IM Supplement: Changing easy-Drive On/Off Configuration from Single Dry Contact Control to Dual Dry Contact Control (L2e Level Controller)
Fisher IM Supplement: Changing easy-Drive On/Off Configuration from Single Dry Contact Control to Dual Dry Contact Control (L2e Level Controller) Manuals & Guides
Instruction Manual Supplement
D103987X012
L2e Controller
September 2017
Changing easy-Drive™ Electric Actuator On/Off
Input Configuration from Single Dry Contact
Control to Dual Dry Contact Control
Supplement to Fisher™ L2e Electric Level Controller Instruction
Manual (D103531X012)
This supplement contains information for converting the easyDrive Electric Actuator from Single Dry Contact Control
Mode to Dual Dry Contact Control Mode.
Refer to the L2e instruction manual (D103531X012
Partner, or at Fisher.com
The Dual Dry Contact Control Mode of operation has proven to be a superior and reliable method of operation with the
easyDrive actuator. This method provides a more stable switch actuation by reducing, or eliminating, the switch
bounce that may be associated with the Single Dry Contact Control Mode.
Refer to the appropriate easyDrive Electric Actuator instruction manual for cautions, warnings, and instructions on
removing the easyDrive actuator cover.
D Fisher D3 Control Valve with easyDrive Electric Actuator (D103460X012
D Fisher D4 Control Valve with easyDrive Electric Actuator (D103597X012
Note
This procedure is for easyDrive Electric Actuators configured for ON/OFF INPUT only.
, for all other information regarding the L2e electric level controller.
), available from your Emerson sales office or Local Business
)
)
L2e Switch Wiring Conversion
1. Ensure easyDrive actuator power is turned off and remove cover.
2. Observe easyDrive actuator electrical connector to determine Dry Contact Control Mode.
3. If easyDrive actuator is wired as shown in figure 1, the actuator is already configured as Dual Dry Contact Control
Mode and no further action is required. Replace easyDrive actuator cover and apply power to put system in service.
4. If easyDrive actuator is wired as shown in figure 2, the actuator is configured as Single Dry Contact Control Mode.
Proceed with the following instructions to reconfigure to Dual Dry Contact Control Mode.
5. Loosen binding screw #2 on easyDrive actuator
6. Install red wire from L2e in easyDrive actuator electrical connector location #2 (marked as “OPEN” or “N.O.”) and
tighten binding screw (see figure 1).
7. Loosen binding screw #3 in easyDrive actuator electrical connector, install blue wire from L2e, and tighten binding
screw (see figure 1).
electrical connector (see figure 2) and remove wire.
www.Fisher.com
L2e Controller
September 2017
Instruction Manual Supplement
D103987X012
8. The L2e wires should now be connected as shown in figure 1:
a. Brown to position #1 (COMM)
b. Red to position #2 (OPEN or N.O.)
c. Blue to position #3 (CLOSE or N.C.)
9. The wiring is now configured as Dual Dry Contact Mode. Proceed to next section for easyDrive electric actuator
software configuration.
Figure 1. Dual Dry Contact Control Figure 2. Single Dry Contact Control
2
Instruction Manual Supplement
D103987X012
L2e Controller
May 2014
Changing the Inputs Settings from Single Dry Contact to Dual Dry
Contacts
Note
All configuration within the valve is done by setting values in Modbus registers. This can be done using any Modbus master (flow
computer, PLC, PC). Configuration software, providing a visual interface to the registers, is available through your Emerson sales
office or Local Business Partner or at Fisher.com
Refer to the “Changing the Inputs from Default Settings” in the D3 or D4 Control Valve with easyDrive Electric Actuator
instruction manual for instructions on how to connect to and communicate with the easyDrive Electric Actuator.
L2e Single Dry Contract Control to Dual Dry Contact Control
.
Once communications have been established with the easyDrive actuator, change register 40043 to configure the
inputs to Dual Dry Contacts as follows:
D Modbus
Set register 40043 (Analog I/P mode) to 0 (L2e Dual Dry Contact)
D Configuration Software
Use radio button to select L2e Dual Dry Contact local digital control when Control Source is set to Local. Click “update”
to accept the change.
Configuration is complete. Replace cover and put system in service.
3
L2e Controller
September 2017
Instruction Manual Supplement
D103987X012
Neither Emerson, Emerson Automation Solutions, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance
of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.
Fisher and easy-Drive are marks owned by one of the companies in the Emerson Automation Solutions business unit of Emerson Electric Co. Emerson
Automation Solutions, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their
respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not
to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are
governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such
products at any time without notice.
Emerson Automation Solutions
Marshalltown, Iowa 50158 USA
Sorocaba, 18087 Brazil
Cernay, 68700 France
Dubai, United Arab Emirates
Singapore 128461 Singapore
www.Fisher.com
4
E 2014, 2017 Fisher Controls International LLC. All rights reserved.
Loading...