Fisher 74913 Parts List
Replacement Parts for Backsplash Faucets
fisher manufacturing company
16101
FLAT SEAT
WASHER
1790-1
ANGLE STOP
W/ CROSS
HANDLET
1792
ANGLE STOP
WITH KEY
46906
CONTROL VALVE
BLUE BUTTON
LEVER HANDLE
DUCK GASKET
LH SWIVEL STEM
RH SWIVEL STEM
2000-7500
SCREW
2000-8000
RED BUTTON
AND
2000-8001
2000-2301
2000-3002
BIBB CAP
10464
2000-5000
WASHER
3000-0010
OR
3000-0011
1000-7502
SCREW
10456
LUBE
3000-0000
RH SWIVEL STEM
REPAIR KIT
OR
3000-0001
LH SWIVEL STEM
REPAIR KIT
10014 (24”)
10022 (36”)
SUPPLY LINE
1/2” F X 1/2” F
10049 (24”)
10006 (36”)
SUPPLY LINE
1/2” M X 1/2” F
3967
16” SWING SPOUT
3964
14” SWING SPOUT
3963
12” SWING SPOUT
3962
10” SWING SPOUT
3961
8” SWING SPOUT
3960
6” SWING SPOUT
3000-0003
DOUBLE JOINT
SPOUT 7 1/4”
4000-0002
DOUBLE JOINT
SPOUT 13”
12564
2.2 GPM
AERATOR
OR
15621
SPOUT NUT
2002
SNAP RING
1600-5000
SPOUT
O-RINGS
10456
LUBE
19119
SWIVEL SPOUT
RETRO-FIT KIT
2400-2103
ELBOWS
1000-8002
SLIP JOINT KIT
4” C/C Backsplash Faucet
Product Installation Guide
Since 1936, Fisher Manufacturing Company has
manufactured heavy-duty, high quality plumbing
products and hardware specialties for the food
service industry. For three generations, the Fisher
family has adhered to a strict dedication of and overall
value. When you install Fisher products… you install
the best. Our hardware is manufactured with the
standardization of internal mechanisms. All chrome
plating is triple plated copper, nickel and chrome
for durability. Every piece of equipment we make is
rigorously tested in both our modern in-house testing
center and in actual fi eld situations under extreme
conditions. Every detail is thoroughly checked. Before
we make our products available to you, they pass
each and every test. You get proven performance.
Guaranteed.
Limited One Year Warranty
Fisher Manufacturing Company warrants its products
and parts thereof (except as noted below) against
defects in materials or workmanship for a period of
one year after the date of original purchase. During
this period Fisher Manufacturing Company will
replace a defective product or part without charge
to you, provided that the entire product is delivered
to Fisher Manufacturing Company. All transportation
and insurance charges for shipping the product to and
from Fisher Manufacturing Company must be borne
by you. Charges for transportation and insurance
may, at the option of Fisher Manufacturing Company,
be refunded depending upon our investigation of
the warranty claim. This warranty does not cover
external fi nish (except at date of original purchase)
or labor costs not specifi cally authorized by Fisher
Manufacturing Company.
A full and complete copy of our One Year limited
warranty is available upon request.
WARNING:
Proposition 65 requires that we provide you with the
following notice: “This product Contains A Chemical
Known To The State Of California To Cause Cancer
and Birth Defects Or Other Reproductive Harm.”
#91588 - 4” c/c Backsplash Faucet with 6” Swing Spout
#94544 - 4” c/c Backsplash Faucet with 8” Swing Spout
#45330 - 4” c/c Backsplash Faucet with 10” Swing Spout
#45349 - 4” c/c Backsplash Faucet with 12” Swing Spout
#45357 - 4” c/c Backsplash Faucet with 14” Swing Spout
#45365 - 4” c/c Backsplash Faucet with 16” Swing Spout
PART NO. 74029
MANFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
(800)421-6162, FAX: (800)832-8238
www.fisher-mfg.com
REV. A
KEEP THIS MANUAL FOR FUTURE REFERENCE
ANSI/A112.18.1M, ANSI/NSF 61.9
fisher manufacturing company - toll free: 800-421-6162 fax: 800-832-8238
www.fi sher-mfg.com
Installation Instructions for Backsplash Faucets
BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION
REGARDING BACKFLOW PREVENTION
Installation Instructions Continued
Installation Notes:
• Be sure water supply is shut-off before beginning.
• Use pipe thread sealant on all threaded joints such as PST or Tefl on tape.
• Check the packaging for missing items BEFORE beginning installation. If
items are missing, contact your supplier.
Items needed for Installation:
• 1 - Medium Sized Crescent Wrenches
• 1 - Plumbers Tape or Pipe Thread Sealant
Step 1.
After unpacking items and checking for missing components, insert the gasket
into the groove on the concentric. Making sure gasket is in place, loosely mount
the concentric and fl ange onto the control valve body.
Step 2.
Mount control valve body to the backsplash by inserting the concentrics through
the backsplash and attaching slip joints. Tighten concentrics and attach elbows
and supply lines (not included) as required. Be sure to use pipe thread sealant
on all threads.
Step 3.
Apply O-ring lube to the O-rings on the swing spout. Make sure the white snap
ring is in place before mounting the swing spout. Mount the swing spout and
tighten the swing spout nut onto the faucet spout outlet.
Step 4.
Turn on water supply and check for leaks.
Step 2
Double Joint Spout
Slip Joint
Kit
1/2” Elbows
(not included)
4”
(101.6mm)
Ø7/8”
Step 3
Swing Spout
Apply O-Ring
Lube Here
Step 1
Step 4
Gasket
Concentric
Flange
Loading...