Fisher 57827 PARTS LIST

Swing Spout Installation Instructions

Step 1.

Apply O-ring lube to the O-rings on the swing spout. Make sure the white snap
ring is in place before mounting the swing spout. Mount the swing spout and
tighten the swing spout nut onto the faucet spout outlet.

Step 2.

Turn on water supply and check for leaks.

FISHER MANUFACTURING COMPANY

Stainless Steel 8” Deck Mount Faucets

Product Installation Guide

Step 1

Step 1

Apply O-ring
Lube Here

Swing Spout

Since 1936, Fisher Manufacturing Company has manu­factured heavy-duty, high quality plumbing products
and hardware specialties for the food service industry.
For three generations, the Fisher family has adhered to
a strict dedication of overall value. When you install
Fisher products… you install the best. Our hardware
is manufactured with the standardization of internal
mechanisms. Every piece of equipment we make is
rigorously tested in both our modern in-house testing
center and in actual fi eld situations under extreme con­ditions. Every detail is thoroughly checked. Before we
make our products available to you, they pass each and
every test. You get proven performance. Guaranteed.

Limited One Year Warranty

Fisher Manufacturing Company warrants its products
and parts thereof (except as noted below) against de­fects in materials or workmanship for a period of one
year after the date of original purchase. During this
period Fisher Manufacturing Company will replace a
defective product or part without charge to you, pro­vided that the entire product is delivered to Fisher
Manufacturing Company. All transportation and in­surance charges for shipping the product to and from
Fisher Manufacturing Company must be borne by you.
Charges for transportation and insurance may, at the
option of Fisher Manufacturing Company, be refunded
depending upon our investigation of the warranty claim.
This warranty does not cover external fi nish (except
at date of original purchase) or labor costs not specifi ­cally authorized by Fisher Manufacturing Company.

A full and complete copy of our One Year limited war­ranty is available upon request.

Lever Handles
53630 - 8” Deck Faucet 6” Swing Spout

57649 - 8” Deck Faucet 8” Swing Spout
57657 - 8” Deck Faucet 10” Swing Spout
57665 - 8” Deck Faucet 12” Swing Spout
57673 - 8” Deck Faucet 14” Swing Spout
57681 - 8” Deck Faucet 16” Swing Spout

Wrist Handles

57827 - 8” Deck Faucet 6” Swing Spout
57835 - 8” Deck Faucet 8” Swing Spout
57843 - 8” Deck Faucet 10” Swing Spout
57851 - 8” Deck Faucet 12” Swing Spout
57878 - 8” Deck Faucet 14” Swing Spout
57886 - 8” Deck Faucet 16” Swing Spout

MANUFACTURING COMPANY

PO BOX 60, TULARE, CA 93275

Part No. - 70343 REV

[phone], FAX: [phone]

www.fi sher-mfg.com

WARNING:

Proposition 65 requires that we provide you with the
following notice: “This product Contains A Chemical

Known To The State Of California To Cause Birth
Defects Or Other Reproductive Harm.”

ANSI/A112.18.1M, ANSI/NSF 61.

9

FISHER MANUFACTURING COMPANY, TOLL FREE: 800-421-6162, FAX:[phone]

www.noleadfaucet.com

.A

Installation Instructions for Stainless Steel 8” Deck Faucet

BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING
JURISDICTION REGARDING BACKFLOW PREVENTION.

Installation Notes:

• Be sure water supply is shut-off before beginning.

• Use pipe thread sealant on all threaded joints such as PST or Teflon tape.

• Check the packaging for missing items BEFORE beginning installation. If
items are missing, contact your supplier.

Items needed for Installation:

• 1 - Medium Sized Crescent Wrenches

• 1 - Plumbers Tape or Pipe Thread Sealant

8” Deck Installation Instructions

Step 1.

After unpacking items and checking for missing components, insert deck
mount elbows by inserting nipples through pre-drilled 7/8” holes in deck.
Tighten deck mount elbows until they are secure, but still can move for ad­justments.

8” Deck Installation Instructions

Step 2.

Insert the gaskets into the grooves on the deck mount elbows. Making sure gas­kets are in place, loosely mount the control valve body on the deck mount elbows
and tighen flange nut by hand.

Step 3.

Once the control valve body is mounted, tighen the flange nuts and the deck
mount elbows securely. attach slip joints kit or supply lines (not included).

Note: If there are leaks at the flange nut, do tighten. Loosen flange nuts

*

and make sure the gaskets are in the groove on the deck mount elbows
and retighten.

Control

Step 2

Valve Body

Gasket

Step 1

8”

[203.2mm]

Deck Mount
Elbows

Ø 7/8”

Slip Joint Kit

Step 3

See Note

*

Deck

Flange Nut