Fisher 53783 Parts Manual
Replacement Parts for SS Deck Mount Faucets
DOUBLE JOINT
SPOUT 7”
DOUBLE JOINT
SPOUT 12”
10022 (36”)
SUPPLY LINE
1/2” F X 1/2” F
10006 (36”)
SUPPLY LINE
1/2” M X 1/2” F
2000-5003
SEAT WASHER
67423
CONTROL VALVE
12912
ANGLE STOP
WITH KEY
2000-7500
SCREW
2000-8000
RED BUTTON
AND
2000-8001
BLUE BUTTON
2000-2301
LEVER HANDLE
56944
BIBB CAP
10464
DUCK GASKET
2000-5000
WASHER
17329
LH SWIVEL STEM
OR
17337
RH SWIVEL STEM
1000-7502
SCREW
10456
LUBE
54518
RH SWIVEL STEM
REPAIR KIT
OR
54526
LH SWIVEL STEM
REPAIR KIT
12904
ANGLE STOP
W/ CROSS
HANDLES
55867 SS
AERATOR
2.2 GPM
54763
SPOUT NUT
2002
SNAP RING
1600-5000
SPOUT
O-RINGS
10456
LUBE
SWIVEL SPOUT
RETRO-FIT KIT
54445
16” SWING SPOUT
54429
14” SWING SPOUT
54410
12” SWING SPOUT
54402
10” SWING SPOUT
54399
8” SWING SPOUT
54380
6” SWING SPOUT
19119
54461
OR
55050
FISHER MANUFACTURING COMPANY
Stainless Steel 4” Deck Mount Faucets
Product Installation Guide
Since 1936, Fisher Manufacturing Company has manufactured heavy-duty, high quality plumbing products
and hardware specialties for the food service industry.
For three generations, the Fisher family has adhered to
a strict dedication of overall value. When you install
Fisher products… you install the best. Our hardware
is manufactured with the standardization of internal
mechanisms. Every piece of equipment we make is
rigorously tested in both our modern in-house testing
center and in actual fi eld situations under extreme conditions. Every detail is thoroughly checked. Before we
make our products available to you, they pass each and
every test. You get proven performance. Guaranteed.
Limited One Year Warranty
Fisher Manufacturing Company warrants its products
and parts thereof (except as noted below) against defects in materials or workmanship for a period of one
year after the date of original purchase. During this
period Fisher Manufacturing Company will replace a
defective product or part without charge to you, provided that the entire product is delivered to Fisher
Manufacturing Company. All transportation and insurance charges for shipping the product to and from
Fisher Manufacturing Company must be borne by you.
Charges for transportation and insurance may, at the
option of Fisher Manufacturing Company, be refunded
depending upon our investigation of the warranty claim.
This warranty does not cover external fi nish (except
at date of original purchase) or labor costs not specifi cally authorized by Fisher Manufacturing Company.
A full and complete copy of our One Year limited warranty is available upon request.
WARNING:
Proposition 65 requires that we provide you with the
following notice: “This product Contains A Chemical
Known To The State Of California To Cause Birth
Defects Or Other Reproductive Harm.”
Lever Handles
53740 - 4” Deck Faucet 6” Swing Spout
53759 - 4” Deck Faucet 8” Swing Spout
53767 - 4” Deck Faucet 10” Swing Spout
53775 - 4” Deck Faucet 12” Swing Spout
53783 - 4” Deck Faucet 14” Swing Spout
53791 - 4” Deck Faucet 16” Swing Spout
Wrist Handles
58564 - 4” Deck Faucet 6” Swing Spout
58572 - 4” Deck Faucet 8” Swing Spout
58580 - 4” Deck Faucet 10” Swing Spout
58599 - 4” Deck Faucet 12” Swing Spout
58602 - 4” Deck Faucet 14” Swing Spout
58610 - 4” Deck Faucet 16” Swing Spout
PART NO. 78611
MANFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
(800)421-6162, FAX: (800)832-8238
www.fisher-mfg.com
REV. A
REV. A
ANSI/A112.18.1M, ANSI/NSF 61.
FISHER MANUFACTURING COMPANY, TOLL FREE: 800-421-6162, FAX:800-832-8238
www.noleadfaucet.com
9
Installation Instructions for SS Deck Faucets
BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION
REGARDING BACKFLOW PREVENTION
Installation Instructions Continued
Installation Notes:
• Be sure to shut off water supply before beginning.
• Use pipe thread sealant such as PST on all threaded joints.
• Check the packaging for missing items BEFORE beginning installation. If items are missing, contact your supplier.
Tools Required for Installation
• Medium Sized Crescent Wrench
• Pipe Thread Sealant
PST
Package Contents
The box should contain the following:
Control Valve
Qty: 1
Each spout includes one 2002 snap ring
Swing Spout
Length determined by model
Qty: 1
and two 1600-5000 o-rings
1000-8002
Slip Joint Kit
Qty: 2
10456
Lube
Installation Instructions
1. Mount control valve on deck by inserting nipples through pre-drilled 7/8” holes in deck. Apply
thread sealant to both nipples and attach slip joint kits. Tighten until control valve is secure.
2. If installing a double joint spout, apply lube to the o-rings on the spout. Mount the double joint
spout and tighten the nut onto the faucet spout outlet.
3. Apply lube to the o-rings on the swing spout. Make sure the white snap ring is in place before
mounting the swing spout. Mount the swing spout and tighten the swing spout nut onto the
faucet spout outlet.
4. Turn on water supply and check for leaks.
Step 2
Step 3
Double Joint Spout
Apply O-Ring
Lube Here
Swing Spout
Apply O-Ring
Lube Here
Step 1
Step 4
Thread Sealant
Goes Here
Slip Joint Kit
Loading...