Fisher 48852 Parts List
Replacement Parts for Backsplash Faucets
8” ADJ. WALL CONTROL VALVE
16101
FLAT SEAT
WASHER
44687
3000-0003
DOUBLE JOINT
SPOUT 7 1/4”
OR
4000-0002
DOUBLE JOINT
SPOUT 13”
2000-7500
SCREW
2000-8000
RED BUTTON
AND
2000-8001
BLUE BUTTON
3984-2300
WRIST HANDLE
2000-3002
BIBB CAP
10464
DUCK GASKET
2000-5000
WASHER
3000-0010
LH SWIVEL STEM
OR
3000-0011
RH SWIVEL STEM
1000-7502
SCREW
10456
LUBE
89621
RH SWIVEL STEM
REPAIR KIT
OR
89613
LH SWIVEL STEM
REPAIR KIT
10014 (24”)
10022 (36”)
SUPPLY LINE
1/2” F X 1/2” F
10049 (24”)
10006 (36”)
SUPPLY LINE
1/2” M X 1/2” F
ANGLE STOP
WITH KEY
3200-2306
CONCENTRIC
FLANGES
16” SWING SPOUT
14” SWING SPOUT
12” SWING SPOUT
10” SWING SPOUT
8” SWING SPOUT
6” SWING SPOUT
2.2 GPM
AERATOR
18694
1790-1
ANGLE STOP
W/ CROSS
HANDLES
1792
1/2” CONCENTRICS
3967
3964
3963
3962
3961
3960
12564
2200-5000
CONCENTRIC
GASKETS
15621
SPOUT NUT
2002
SNAP RING
1600-5000
SPOUT
O-RINGS
10456
LUBE
19119
SWIVEL SPOUT
RETRO-FIT KIT
2400-2103
ELBOWS
1000-8002
SLIP JOINT KIT
fisher manufacturing company
8” C/C Backsplash Faucet
Product Installation Guide
Since 1936, Fisher Manufacturing Company has
manufactured heavy-duty, high quality plumbing
products and hardware specialties for the food service
industry. For three generations, the Fisher family has
adhered to a strict dedication of and overall value.
When you install Fisher products… you install the best.
Our hardware is manufactured with the standardization
of internal mechanisms. All chrome plating is triple
plated copper, nickel and chrome for durability. Every
piece of equipment we make is rigorously tested
in both our modern in-house testing center and in
actual fi eld situations under extreme conditions.
Every detail is thoroughly checked. Before we make
our products available to you, they pass each and
every test. You get proven performance. Guaranteed.
Limited One Year Warranty
Fisher Manufacturing Company warrants its products
and parts thereof (except as noted below) against
defects in materials or workmanship for a period of
one year after the date of original purchase. During
this period Fisher Manufacturing Company will
replace a defective product or part without charge
to you, provided that the entire product is delivered
to Fisher Manufacturing Company. All transportation
and insurance charges for shipping the product
to and from Fisher Manufacturing Company must
be borne by you. Charges for transportation and
insurance may, at the option of Fisher Manufacturing
Company, be refunded depending upon our
investigation of the warranty claim. This warranty
does not cover external fi nish (except at date of
original purchase) or labor costs not specifi cally
authorized by Fisher Manufacturing Company.
A full and complete copy of our One Year limited
warranty is available upon request.
WARNING:
Proposition 65 requires that we provide you with the
following notice: “This product Contains A Chemical
Known To The State Of California To Cause Birth
Defects Or Other Reproductive Harm.”
KEEP THIS MANUAL FOR FUTURE REFERENCE
#48801 - 8” c/c Backsplash Faucet with 6” Swing Spout
#48828 - 8” c/c Backsplash Faucet with 8” Swing Spout
#48836 - 8” c/c Backsplash Faucet with 10” Swing Spout
#48844 - 8” c/c Backsplash Faucet with 12” Swing Spout
#48852 - 8” c/c Backsplash Faucet with 14” Swing Spout
#48860 - 8” c/c Backsplash Faucet with 16” Swing Spout
ANSI/A112.18.1M, ANSI/NSF 61.9
PART NO. 73621
MANFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
(800)421-6162, FAX: (800)832-8238
www.fisher-mfg.com
REV. A
fisher manufacturing company - toll free: 800-421-6162 fax: 800-832-8238
www.fi sher-mfg.com
Installation Instructions for Backsplash Faucets
BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION
REGARDING BACKFLOW PREVENTION
Installation Instructions Continued
Installation Notes:
• Be sure to shut off water supply before beginning.
• Use pipe thread sealant such as PST on all threaded joints.
• Check the packaging for missing items BEFORE beginning installation. If items are missing, contact your supplier.
Tools Required for Installation
• Medium Sized Crescent Wrench
• Pipe Thread Sealant
PST
Package Contents
The box should contain the following:
Control Valve
Qty: 1
Swing Spout
Length determined by model
Qty: 1
3200-2306
Concentric
Flanges
Qty: 2
18694
1/2” Concentrics
Qty: 2
2200-5000
Concentric Gaskets
Qty: 2
10456
Lube
Qty: 1
Installation Instructions
1. After unpacking items and checking for missing components, insert the gasket into the groove
on the concentric. Making sure gasket is in place, loosely mount the concentric and fl ange onto
the control valve body.
2. Mount control valve body to the backsplash by inserting the concentrics through the backsplash
and attaching slip joints. Tighten concentrics and attach elbows and supply lines (not included)
as required. Be sure to use pipe thread sealant on all threads.
3. Optional DJ swivel spout, apply lube to the o-ring on the spout. Mount the DJ swivel spout and
tighten the nut onto the faucet spout outlet.
4. Apply lube to the o-rings on the swing spout. Make sure the white snap ring is in place before
mounting the swing spout. Mount the swing spout and tighten the swing spout nut onto the
faucet spout outlet.
4. Turn on water supply and check for leaks.
Step 2
Step 3
Apply O-Ring
Lube Here
Double Joint
Spout
Ø7/8”
Elbows
(not included)
Step 4
Slip Joints
8”
[203.2mm]
Supply lines
(not included)
Swing Spout
Apply O-Ring
Lube Here
Step 1
Step 5
Gasket
Concentric
Flange
Loading...