Fisher 48755 Parts Manual
Replacement Parts for Wall Mount Faucets
8” ADJ. WALL CONTROL VALVE
16101
FLAT SEAT
WASHER
3200-2306
ECCENTRIC
FLANGES
18090
Part No. - 73307 REV.A
2000-7500
SCREW
2000-8000
RED BUTTON
AND
2000-8001
BLUE BUTTON
3984-2300
WRIST HANDLE
2000-3002
BIBB CAP
10464
DUCK GASKET
2000-5000
WASHER
3000-0010
LH SWIVEL STEM
OR
3000-0011
RH SWIVEL STEM
1000-7502
SCREW
10456
LUBE
3200-2307
1/2” ECCENTRICS
3967
16” SWING SPOUT
3964
14” SWING SPOUT
3963
12” SWING SPOUT
3962
10” SWING SPOUT
3961
8” SWING SPOUT
3960
6” SWING SPOUT
89621
RH SWIVEL STEM
REPAIR KIT
OR
89613
LH SWIVEL STEM
REPAIR KIT
10014 (24”)
10022 (36””)
SUPPLY LINE
1/2” F X 1/2”F
10049 (24”)
10006 (36””)
SUPPLY LINE
1/2” M X 1/2”F
ANGLE STOP
ANGLE STOP
WITH CROSS
2200-5000
ECCENTRIC GASKETS
MANUFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
(800)421-6162, FAX: (800)832-8238
www.fi sher-mfg.com
1792
WITH KEY
1790-1
HANDLES
12564
2.2 GPM
AERATOR
15621
SPOUT NUT
2002
SNAP RING
1600-5000
SPOUT
O-RING
10456
LUBE
19119
SWIVEL SPOUT
RETRO-FIT KIT
2400-2103
ELBOWS
3000-0003
DOUBLE JOINT
SPOUT 7 1/2”
OR
4000-0002
DOUBLE JOINT
SPOUT 14”
2200-0000
SLIP JOINT KIT
FISHER MANUFACTURING COMPANY
8” Adjustable Wall Mount Faucet
Product Installation Guide
Since 1936, Fisher Manufacturing Company has manufactured heavy-duty, high
quality plumbing products and hardware
specialties for the food service industry.
For three generations, the Fisher family has adhered to a strict dedication of and overall value.
When you install Fisher products… you install
the best. Our hardware is manufactured with
the standardization of internal mechanisms. All
chrome plating is triple plated copper, nickel and
chrome for durability. Every piece of equipment
we make is rigorously tested in both our modern
in-house testing center and in actual fi eld situa-
tions under extreme conditions. Every detail is
thoroughly checked. Before we make our products available to you, they pass each and every
test. You get proven performance. Guaranteed.
Limited One Year Warranty
Fisher Manufacturing Company warrants its prod-
ucts and parts thereof (except as noted below)
against defects in materials or workmanship for a
period of one year after the date of original purchase. During this period Fisher Manufacturing
Company will replace a defective product or part
without charge to you, provided that the entire product is delivered to Fisher Manufacturing Company.
All transportation and insurance charges for shipping the product to and from Fisher Manufacturing
Company must be borne by you. Charges for transportation and insurance may, at the option of Fisher
Manufacturing Company, be refunded depending
upon our investigation of the warranty claim. This
warranty does not cover external fi nish (except at
date of original purchase) or labor costs not specifi -
cally authorized by Fisher Manufacturing Company.
A full and complete copy of our One Year limited
warranty is available upon request.
WARNING:
Proposition 65 requires that we provide you with the
following notice: “This product Contains A Chemical
Known To The State Of California To Cause Birth
Defects Or Other Reproductive Harm.”
FISHER MANUFACTURING COMPANY, TOLL FREE: 800-421-6162, FAX:800-832-8238
www.fi sher-mfg.com
#48739 - 8” Adj. Wall Mount Faucet with 6” Swing
Spout 7” DJ Swing Spout
#48747- 8” Adj. Wall Mount Faucet with 8” Swing
Spout 7” DJ Swing Spout
#48755 - 8” Adj. Wall Mount Faucet with 10”
Swing Spout 7” DJ Swing Spout
#48763 - 8” Adj. Wall Mount Faucet with 12”
Swing Spout 7” DJ Swing Spout
#48771 - 8” Adj. Wall Mount Faucet with 14”
Swing Spout 7” DJ Swing Spout
#48798 - 8” Adj. Wall Mount Faucet with 16”
Swing Spout 7” DJ Swing Spout
ANSI/A112.18.1M, ANSI/NSF 61.
9
Installation Instructions for Wall Mount Faucet
Installation Instructions Continued
BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING
JURISDICTION REGARDING BACKFLOW PREVENTION.
Installation Notes:
• Be sure water supply is shut-off before beginning.
• Use pipe thread sealant on all threaded joints such as PST or Tefl on tape.
• Check the packaging for missing items BEFORE beginning installation. If
items are missing, contact your supplier.
Package Contents
The box should contain the following:
18090
8” Adj. Control Valve
Swing Spout
Length determined by model
Each spout includes one 2002
snap ring and two 1600-5000
Qty:1
O-rings
3200-2306
Eccentric Flanges
Qty: 2
3200-2307
1/2” Eccentrics
Qty: 2
2200-5000
Eccentrics Gaskets
Qty: 2
10456
Qty: 1
Items needed for Installation
• 1 - Medium Sized Crescent Wrenches
• 1 - Plumbers Tape or Pipe Thread Sealant
Installation Instructions
Step 1.
After unpacking items and checking for missing components, insert and center the gasket into the
female swivel inlets of the 8” control valve body. Loosely mount the eccentrics and fl ange onto the
control valve body.
Step 2.
Mount control valve body to either a wall with a male supply nipples, or backsplash with nipples (not
included). Be sure to use pipe thread sealant on the supply nipple threads. Adjust the eccentrics as
needed in order to mount the control valve level. Once level, tighten the eccentrics
Lube
Step 2
Step 3
Ø 7/8”
Elbows
(Not Included)
DJ Swing Spout
Apply O-ring
Lube Here
1/2” NPT Supply
Nipples (Not Included)
7 3/4” - 8 1/4”
[196.9mm] - [209.6mm]
1/2” NPT Supply
Nipples (Not Included)
7 3/4” - 8 1/4”
[196.9mm] - [209.6mm]
Step 4
Supply Lines
(Not Included)
Swing Spout
Apply O-ring
Lube Here
Step 3.
Optional DJ swivel spout, apply lube to the O-ring on the spout. Mount the DJ swivel spout and
tighten the nut onto the faucet spout outlet.
Step 4.
Apply O-ring lube to the O-rings on the swing spout. Make sure the white snap ring is in place before
mounting the swing spout. Mount the swing spout and tighten the swing spout nut onto the faucet
spout outlet.
Step 5.
Turn on water supply and check for leaks.
Step 1
Gasket
Eccentric
Flange
Step 5
Loading...