Fisher 46280 PARTS LIST
Swing Spout Installation Instructions
Step 1.
Apply O-ring lube to the O-rings on the swing spout. Make sure the white snap
ring is in place before mounting the swing spout. Mount the swing spout and
tighten the swing spout nut onto the faucet spout outlet.
Step 2.
Turn on water supply and check for leaks.
Step 1
Apply O-ring
Lube Here
Step 2
Swing Spout
FISHER MANUFACTURING COMPANY
Stainless Steel 8” Backsplash/Adjustable
Wall Mount Faucets
Product Installation Guide
Since 1936, Fisher Manufacturing Company has manufactured heavy-duty, high quality plumbing products
and hardware specialties for the food service industry.
For three generations, the Fisher family has adhered to a strict dedication of overall value. When
you install Fisher products… you install the best.
Our hardware is manufactured with the standardization of internal mechanisms. Every piece of
equipment we make is rigorously tested in both
our modern in-house testing center and in actual
field situations under extreme conditions. Every
detail is thoroughly checked. Before we make our
products available to you, they pass each and every test. You get proven performance. Guaranteed.
Limited One Year Warranty
Fisher Manufacturing Company warrants its products and parts thereof (except as noted below) against
defects in materials or workmanship for a period of
one year after the date of original purchase. During
this period Fisher Manufacturing Company will
replace a defective product or part without charge
to you, provided that the entire product is delivered
to Fisher Manufacturing Company. All transportation and insurance charges for shipping the product
to and from Fisher Manufacturing Company must
be borne by you. Charges for transportation and
insurance may, at the option of Fisher Manufacturing Company, be refunded depending upon our
investigation of the warranty claim. This warranty does not cover external finish (except at date
of original purchase) or labor costs not specifically authorized by Fisher Manufacturing Company.
Lever Handles
46280 - 8” Backsplash/Wall Faucet 6” Swing Spout
46299 - 8” Backsplash/Wall Faucet 8” Swing Spout
46302 - 8” Backsplash/Wall Faucet 10” Swing Spout
46310 - 8” Backsplash/Wall Faucet 12” Swing Spout
46329 - 8” Backsplash/Wall Faucet 14” Swing Spout
46337 - 8” Backsplash/Wall Faucet 16” Swing Spout
Wrist Handles
57061 - 8” Backsplash/Wall Faucet 6” Swing Spout
57088 - 8” Backsplash/Wall Faucet 8” Swing Spout
57096 - 8” Backsplash/Wall Faucet 10” Swing Spout
57118 - 8” Backsplash/Wall Faucet 12” Swing Spout
57126 - 8” Backsplash/Wall Faucet 14” Swing Spout
57134 - 8” Backsplash/Wall Faucet 16” Swing Spout
MANUFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
(800)421-6162, FAX: (800)832-8238
Part No. - 62979 REV
www.fisher-mfg.com
A full and complete copy of our One Year limited
warranty is available upon request.
ANSI/A112.18.1M, ANSI/NSF 61.
FISHER MANUFACTURING COMPANY, TOLL FREE: 800-421-6162, FAX:800-832-8238
www.noleadfaucet.com
.A
9
Installation Instructions for Stainless Steel 8” BS/AW Mount Faucet
BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING
JURISDICTION REGARDING BACKFLOW PREVENTION.
Installation Notes:
• Be sure water supply is shut-off before beginning.
• Use pipe thread sealant on all threaded joints such as PST or Teflon tape.
• Check the packaging for missing items BEFORE beginning installation. If
items are missing, contact your supplier.
Items needed for Installation:
• 1 - Medium Sized Crescent Wrenches
• 1 - Plumbers Tape or Pipe Thread Sealant
8” Backsplash Installation Instructions
Step 1.
After unpacking items and checking for missing components, insert the gasket
into the groove on the concentric. Making sure gasket is in place, loosely mount
the concentric and flange onto the control valve body.
Step 2.
Mount control valve body to the backsplash by inserting the concentrics through
the backsplash and attaching slip joints. Tighten concentrics and attach elbows
and supply lines (not included) as required. Be sure to use pipe thread sealant
on all threads.
Step 1
Gasket
Flange
8” Adjustable Wall Mount Installation Instructions
Step 1.
After unpacking items and checking for missing components, insert and center
the gasket into the female swivel inlets of the 8” control valve body. Loosely
mount the eccentrics and flange onto the control valve body.
Step 2.
Mount control valve body to either a wall with a male supply nipples, or backsplash with nipples (not included). Be sure to use pipe thread sealant on the supply nipple threads. Adjust the eccentrics as needed in order to mount the control
valve level. Once level, tighten the eccentrics
Step 1
Gasket
Flange
Eccentric
Step 2
1/2” NPT Supply
Nipples (Not Included)
Ø 7/8”
Concentric
Step 2
Elbows
Ø7/8”
Slip Joints
8”
[204mm]
7 3/4” - 8 1/4”
[196.9mm] - [209.6mm]
1/2” NPT Supply
Nipples (Not Included)
7 3/4” - 8 1/4”
[196.9mm] - [209.6mm]
Elbows
Loading...