Fisher 38156 Parts Manual

Replacement Parts for Pre-Rinse Units

2011-0000

PRE-RINSE

GOOSENECK

SVL 1/4”

31” RISER

2902-12

WALL BRACKET

2943

PIPE CLAMP

MOUNT HOOK

66591

CONTROL

VALV E

47279

TEMPERATURE

CONTROL VALVE

2000-5003

SEAT WASHER

PART NO. 75154

38423

ISH

C A

2000-7500

SCREW

2000-8000

RED BUTTON

AND

2000-8001

BLUE BUTTON

LEVER HANDLE

2000-3002

BIBB CAP

73657

DUCK GASKET

73741

WASHER

18848

RH SWIVEL

STEM

18821

LH SWIVEL

STEM

1000-7502

SCREW

73521

LUBE

2916-151/2

15 1/2” HOSE

2922-5000

WASHER

2932-0002

WATTS N9 BACK-FLOW PREVENTER

BACKFLOW

PREVENTER

71390

INSULATED

HANDLE

71307

ULTRA SPRAY

VALV E

2949-9001

SCRUB BRUSH

2000-0002

HANDLE LEVER KIT

16” SWING SPOUT

14” SWING SPOUT

12” SWING SPOUT

10” SWING SPOUT

8” SWING SPOUT

54518

RH SWIVEL STEM

REPAIR KIT

54526

LH SWIVEL STEM

REPAIR KIT

12912

ANGLE STOP

WITH KEY

6” SWING SPOUT

MANFACTURING COMPANY

PO BOX 60, TULARE, CA 93275

(800)421-6162, FAX: (800)832-8238

www.fisher-mfg.com

54445

54429

54410

54402

54399

54380

ANGLE STOP

W/ CROSS

HANDLES

1000-5005

12904

O-RING

2912-7501

2909-6000

71420

SPRAY VALVE

REPAIR KIT

64610

1000-5001

2912-6000

64580

INCLUDES:

1000-5003 WASHER

1000-7502 SCREW

2922-5000

64637

2909-5000

64645

ADD-ON CONTROL

VALVE LESS SPOUT

SPOUT NUT

55867

2.2 GPM

AERATOR

SNAP RING

SUPPLY LINE

1/2”F X 1/2”F X 36”

SUPPLY LINE

1/2”F X 1/2”M X 36”

38318

73684

20020

1600-5000

SPOUT

O-RINGS

73521

LUBE

19119

SWIVEL SPOUT

RETRO-FIT KIT

10022

10006

REV. A

fisher manufacturing company

PRHS-SV-SDTL

Product Installation Guide

Since 1936, Fisher Manufacturing Company has manufactured heavy-duty, high quality plumbing products and hardware specialties for the food service industry. For three generations, the Fisher family has adhered to a strict dedication of and overall value. When you install Fisher products… you install the best. Our hardware is manufactured with the standardization of internal mechanisms. All chrome plating is triple plated copper, nickel and chrome for durability. Every piece of equipment we make is rigorously tested in both our modern in-house testing center and in actual ﬁ eld situations under extreme conditions. Every detail is thoroughly checked. Before we make our products available to you, they pass each and every test. You get proven performance. Guaranteed.

Limited One Year Warranty

Fisher Manufacturing Company warrants its products and parts thereof (except as noted below) against defects in materials or workmanship for a period of one year after the date of original purchase. During this period Fisher Manufacturing Company will replace a defective product or part without charge to you, provided that the entire product is delivered to Fisher Manufacturing Company. All transportation and insurance charges for shipping the product to and from Fisher Manufacturing Company must be borne by you. Charges for transportation and insurance may, at the option of Fisher Manufacturing Company, be refunded depending upon our investigation of the warranty claim. This warranty does not cover external ﬁ nish (except at date of original purchase) or labor costs not speciﬁ cally authorized by Fisher Manufacturing Company.

A full and complete copy of our One Year limited warranty is available upon request.

Warning:This product can expose you to chemicals including Lead, Nickel (Metallic), Di(2-ethylhexyl) phathalate (DEHP) which are known to the State of California to cause cancer, and Lead. Di(2-ethylhexyl) phathalate (DEHP) which are known to the State of Califorina to cause birth defects or reproductive harm. For more information go to:

www.P65Warnings.ca.gov.

KEEP THIS MANUAL FOR FUTURE REFERENCE

fisher manufacturing company - toll free: 800-421-6162 fax: 800-832-8238

www.ﬁ sher-mfg.com

38156 - SS PRERINSE SVL SDLH

ANSI/A112.18.1M, ANSI/NSF 61.9

Installation Instructions for Pre-Rinse Units

BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION REGARDING BACKFLOW PREVENTION

Installation Notes:

• Be sure to shut oﬀ water supply before beginning.

• Use pipe thread sealant such as PST on all threaded joints.

• Check the packaging for missing items BEFORE beginning installation. If items are missing, contact your supplier.

Tools Required for Installation

• Medium Sized Crescent Wrenches

• Pipe Thread Sealant

• Phillips Screwdriver

• 7/16” Drill Bit

• 1/8” Allen Wrench

Installation Instructions

1. If no add-on faucet will be installed, proceed to step 2 If installing an add-on faucet, mount the small riser to the control valve body using thread sealant. Thread the add-on faucet to the other end of the small riser, again using thread sealant.

2. Mount control valve 66591 to deck by inserting nipple through pre-cut hole and attaching slip joint beneath the deck. Tighten slip joint until control valve is secure.

3. Attach mixing valve 47279 to control valve 66561. Be sure to use thread sealant when attaching control valves. Install your water source to the 47279 mixing valve.

4. Apply thread sealant to one end of the riser’s threads, after thread sealant is applied insert into the single deck control valve inlet and tighten, ( or add on valve if installing add-on faucet).

5. If no wall bracket is to be installed, proceed to Step 6, otherwise do the following:

a. Locate and drill a Ø7/16” hole in the wall directly

behind and about 3/4 the way up the riser pipe.

b. Loosely attach the front and back of the pipe clamp

onto the riser pipe.

c. Hold the wall bracket ﬂ ange against the wall,

centered with the hole. Use the wall screws and a screw driver to mount the ﬂ ange to the wall.

d. Slide part, but not all, of the wall bracket rod non-

threaded end ﬁ rst through the center hole of the ﬂ ange and into the wall.

e. Align the rod with the pipe clamp and thread the

rod into the pipe clamp. Be sure the rod is level by adjusting the pipe clamp position.

f. Once level, ﬁ x the rod in place by tightening both

the set screw located in the ﬂ ange and the pipe clamp screws.

6. Apply thread sealant to riser’s threads and attach to swivel gooseneck sub assembly.

7. Apply thread sealant to SS hose and connect to swivel gooseneck sub assembly.

8. Fit one of the handle gaskets inside the outlet of the insulated handle and mount the spray valve onto it.

PST

Step 1

Step 2

Step 3

47279

66591

Thread Sealant

Goes Here

ISHER CA

I SHE

R C

I S

H ER

C A

Slip Joint

Thread Sealant

Goes Here

Attach Supply

Lines Here

Installation Instructions Continued

9. Fit the other handle gasket inside the inlet of the insulated handle and mount the handle onto the SS hose. If installing backﬂ ow preventer, attach it between the SS hose and insulated handle. Be sure that gaskets are used on both sides of the backﬂ ow preventer.

10. If installing a brush, do so by pressing brush into the bumper of the spray valve until secure.

11. To install swing spout to add-on faucet, apply o-ring lube to the o-rings on the swing spout. Make sure the white snap ring is in place before mounting the swing spout. Mount the swing spout and tighten the swing spout nut onto the add-on faucet spout outlet.

12. If no hose clamp will be installed, proceed to step

13. If installing hose clamp, place the hose clamp on the riser. Adjusting it to the desired height and tighten.

13. Turn on water supply and check for leaks.

Step 5 Step 6

Excess Rod Length

Trim to Fit (optional)

Wall

Wall Screw

Set Screw

Thread Sealant

Goes Here

Pipe

Clamp

Riser Pipe

Step 9 Step 10 Step 11 Step 12

Handle Gasket

WATTS N9 BACK-FLOW PREVENTER

Step 4

Step 7

Thread Sealant

Goes Here

Swing Spout

Apply O-Ring

Lube Here

HER

I S H

E R C

Thread Sealant

Goes Here

Step 8

Handle

Gasket

ISHER CA