Fisher 38148 Parts Manual
Replacement Parts for Pre-Rinse Units
2924-6000
SPRING
GOOSENECK
2925-6300
HOSE HOOK
70696
PIPE TO HOSE
ADAPTER
2902-12
WALL BRACKET
CONTROL
VALV E
PART NO. 78646
63363
SS 3/8” PIPE
21” RISER
2000-7500
SCREW
2000-8000
RED BUTTON
AND
2000-8001
BLUE BUTTON
2000-2301
LEVER HANDLE
2000-3002
BIBB CAP
10464
DUCK GASKET
2000-5000
WASHER
64424
LH CHECK STEM
OR
64440
RH CHECK STEM
2000-6000
SPRING
2000-0001
RETAINER
ASSEMBLY
10456
LUBE
2914
STAINLESS STEEL
HOSE 36”
2922-5000
W
ASHER
2932-0002
WATTSN9
BACK-FLOW
PREVENTER
BACKFLOW
PREVENTER
71390
INSULATED
HANDLE
71307
ULTRA SPRAY
VALV E
2949-9001
SCRUB BRUSH
10022 (36”)
SUPPLY LINE
1/2” F x 1/2” F
10006 (36”)
SUPPLY LINE
1/2” M x 1/2” F
3000-0000
RH SWIVEL
REPAIR KIT
16” SWING SPOUT
54502
RH CHECK STEM
REPAIR KIT
OR
54510
LH CHECK STEM
REPAIR KIT
14” SWING SPOUT
12” SWING SPOUT
10” SWING SPOUT
8” SWING SPOUT
6” SWING SPOUT
MANFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
(800)421-6162, FAX: (800)832-8238
www.fisher-mfg.com
35572
NOZZLE FOR
71307 SPRAY
VALV E
2949-8600
CUP WASHER
1000-7502
SEAT SCREW
10456
LUBE
SEAT WASHER
54445
54429
54410
54402
54399
54380
RH SWIVEL
2000-5003
2949-9002
BLUE BUMPER
17337
STEM
2000-5000
WASHER
1000-5005
O-RING
2912-2501
2912-7501
2909-6000
12912
ANGLE STOP
WITH KEY
10464
DUCK GASKET
55867
2.2 GPM
AERATOR
2000-3002
BIBB CAP
1000-5003 WASHER
1000-7502 SCREW
12904
ANGLE STOP
W/ CROSS
HANDLES
2000-2301
LEVER HANDLE
2000-8000
RED BUTTON
2000-8001
BLUE BUTTON
2901-0000
ADD-ON CONTROL
VALVE LESS SPOUT
54763
SPOUT NUT
2002
SNAP RING
1600-5000
SPOUT
O-RINGS
10456
LUBE
SWIVEL SPOUT
RETRO-FIT KIT
7 14 2 0
SS SPRAY
VALV E
REPAIR KIT
64610
1000-5001
2912-6000
64580
INCLUDES:
2922-5000
64637
2909-5000
64653
2000-7500
SCREW
AND
19119
REV. A
fisher manufacturing company
Stainless Steel 4” Deck Pre-Rinse Unit
Product Installation Guide
Since 1936, Fisher Manufacturing Company has manufactured heavy-duty, high quality plumbing products
and hardware specialties for the food service industry.
For three generations, the Fisher family has adhered to a strict dedication of overall value. When
you install Fisher products… you install the best.
Our hardware is manufactured with the standardization of internal mechanisms. Every piece of
equipment we make is rigorously tested in both
our modern in-house testing center and in actual
fi eld situations under extreme conditions. Every
detail is thoroughly checked. Before we make our
products available to you, they pass each and every test. You get proven performance. Guaranteed.
Limited One Year Warranty
Fisher Manufacturing Company warrants its products and parts thereof (except as noted below) against
defects in materials or workmanship for a period of
one year after the date of original purchase. During
this period Fisher Manufacturing Company will replace a defective product or part without charge to
you, provided that the entire product is delivered
to Fisher Manufacturing Company. All transportation and insurance charges for shipping the product to and from Fisher Manufacturing Company
must be borne by you. Charges for transportation
and insurance may, at the option of Fisher Manufacturing Company, be refunded depending upon
our investigation of the warranty claim. This warranty does not cover external fi nish (except at date
of original purchase) or labor costs not specifi cally authorized by Fisher Manufacturing Company.
A full and complete copy of our One Year limited
warranty is available upon request.
WARNING:
Proposition 65 requires that we provide you with the
following notice: “This product Contains A Chemical
Known To The State Of California To Cause Birth
Defects Or Other Reproductive Harm.”
KEEP THIS MANUAL FOR FUTURE REFERENCE
FISHER MANUFACTURING COMPANY, TOLL FREE: 800-421-6162, FAX:800-832-8238
www.noleadfaucet.com
#53961 - Stainless Steel Pre-Rinse, Spring Style
4” Deck Control Valve, 21” Riser, 36” Hose &
Spray Valve with Lever Handles
ANSI/A112.18.1M, ANSI/NSF 61.9
Installation Instructions for SS Pre-Rinse Units
BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION
REGARDING BACKFLOW PREVENTION
Installation Notes:
• Be sure to shut off water supply before beginning.
• Use pipe thread sealant such as PST on all threaded joints.
• Check the packaging for missing items BEFORE beginning installation. If items are missing, contact your supplier.
Tools Required for Installation
• Medium Sized Crescent Wrenches
• Pipe Thread Sealant
• Phillips Screwdriver
• 7/16” Drill Bit
• 1/8” Allen Wrench
Installation Instructions
1. If no add-on faucet will be installed, proceed to step
2. If installing an add-on faucet, mount the small
riser to the control valve body using thread sealant.
Thread the add-on faucet to the other end of the
small riser, again using thread sealant.
2. Mount control valve on deck by Inserting nipples
through pre-drilled 7/8” holes in deck. Apply thread
sealant to both nipples and attach slip joint kits.
Tighten until control valve is secure.
3. Mount the pipe to hose adapter to the enclosed
riser using thread sealant. Mount the other end of
the riser to the female outlet of the add-on body (if
applicable), or the control valve body.
4. If no wall bracket is to be installed, proceed to Step
5, otherwise do the following:
a. Locate and drill a Ø7/16” hole in the wall directly
behind and about 3/4 the way up the riser pipe.
b. Loosely attach the front and back of the pipe
clamp onto the riser pipe.
c. Hold the wall bracket fl ange against the wall,
centered with the hole. Use the wall screws and
a screw driver to mount the fl ange to the wall.
d. Slide part, but not all, of the wall bracket rod non-
threaded end fi rst through the center hole of the
fl ange and into the wall.
e. Align the rod with the pipe clamp and thread the
rod into the pipe clamp. Be sure the rod is level
by adjusting the pipe clamp position.
f. Once level, fi x the rod in place by tightening both
the set screw located in the fl ange and the pipe
clamp screws.
5. Slip the hose hook over the pipe to hose adapter.
Using thread sealant and a crescent wrench, thread
the SS hose into the pipe to hose adapter.
6. Install gooseneck spring by slipping SS hose
through the spring. Spring will fi t over adapter which
holds it in an upright position. Note: Be sure spring
is installed as shown. DO NOT INSTALL SHORT
BEND DOWN.
7. Fit one of the handle gaskets inside the outlet of the
insulated handle and mount the spray valve onto it.
PST
Step 1
Thread Sealant
Goes Here
Step 2
Thread Sealant
Goes Here
Slip Joint Kit
Step 3
Thread Sealant
Goes Here
Installation Instructions Continued
8. Fit the other handle gasket inside the inlet of the
insulated handle and mount the handle onto the
SS hose. If installing backfl ow preventer, attach it
between the SS hose and insulated handle. Be sure
that gaskets are used on both sides of the backfl ow
preventer.
9. If installing a brush, do so by pressing brush into
the bumper of the spray valve until secure.
10. To install swing spout to add-on faucet, apply
o-ring lube to the o-rings on the swing spout.
Make sure the white snap ring is in place before
mounting the swing spout. Mount the swing spout
and tighten the swing spout nut onto the add-on
faucet spout outlet.
11. Turn on water supply and check for leaks.
Step 5 Step 6
Spring Bend
On This Side
Thread Sealant
Goes Here
Step 8 Step 9 Step 10 Step 11
Handle Gasket
WATTSN9
BACK-FLOW
PREVENTER
Step 4
Excess Rod Length
Trim to Fit (optional)
Wall
Wall Screw
Set Screw
Pipe
Clamp
Riser Pipe
Step 7
Swing Spout
Apply O-Ring
Lube Here
Handle Gasket
Loading...