Fisher 3615 Parts List
Replacement Parts for Backsplash Faucets
fisher manufacturing company
2000-5003
SEAT WASHER
SWIVEL
T
O
H
H
O
T
3600
CONTROL VALVE
LEVER HANDLE
LH SWIVEL STEM
RH SWIVEL STEM
L
D
O
C
C
O
D
L
2000-7500
SCREW
2000-8000
RED BUTTON
AND
2000-8001
BLUE BUTTON
2000-2301
2000-3002
BIBB CAP
10464
DUCK GASKET
2000-5000
WASHER
3000-0010
OR
3000-0011
1000-7502
SCREW
10456
LUBE
3000-0000
RH SWIVEL STEM
REPAIR KIT
OR
3000-0001
LH SWIVEL STEM
REPAIR KIT
1792
ANGLE STOP
WITH KEY
1790-1
ANGLE STOP
W/ CROSS
HANDLE
10014 (24”)
10022 (36”)
SUPPLY LINE
1/2” F X 1/2” F
10049 (24”)
10006 (36”)
SUPPLY LINE
1/2” M X 1/2” F
12564
2.2 GPM
AERATOR
1000-8002
SLIP JOINT KIT
GOOSENECK
15621
SPOUT NUT
2002
SNAP RING
1600-5000
SPOUT
O-RINGS
10456
LUBE
19119
SWIVEL SPOUT
RETRO-FIT KIT
3968
6” SWIVEL
GOOSENECK
SPOUT
3965
12” SWIVEL
SPOUT
2400-2103
ELBOWS
4” C/C Backsplash Faucet
Product Installation Guide
Since 1936, Fisher Manufacturing Company has
manufactured heavy-duty, high quality plumbing
products and hardware specialties for the food service
industry. For three generations, the Fisher family has
adhered to a strict dedication of and overall value.
When you install Fisher products… you install the best.
Our hardware is manufactured with the standardization
of internal mechanisms. All chrome plating is triple
plated copper, nickel and chrome for durability.
Every piece of equipment we make is rigorously
tested in both our modern in-house testing center and
in actual fi eld situations under extreme conditions.
Every detail is thoroughly checked. Before we make
our products available to you, they pass each and
every test. You get proven performance. Guaranteed.
Limited One Year Warranty
Fisher Manufacturing Company warrants its products
and parts thereof (except as noted below) against
defects in materials or workmanship for a period of
one year after the date of original purchase. During
this period Fisher Manufacturing Company will
replace a defective product or part without charge to
you, provided that the entire product is delivered to
Fisher Manufacturing Company. All transportation and
insurance charges for shipping the product to and from
Fisher Manufacturing Company must be borne by you.
Charges for transportation and insurance may, at the
option of Fisher Manufacturing Company, be refunded
depending upon our investigation of the warranty claim.
This warranty does not cover external fi nish (except at
date of original purchase) or labor costs not specifi cally
authorized by Fisher Manufacturing Company.
A full and complete copy of our One Year limited
warranty is available upon request.
WARNING:
Proposition 65 requires that we provide you with the
following notice: “This product Contains A Chemical
Known To The State Of California To Cause Birth
Defects Or Other Reproductive Harm.”
KEEP THIS MANUAL FOR FUTURE REFERENCE
#3615 - 4” c/c Backsplash Faucet with 12” Swivel
Gooseneck Spout
#1996 - 4” c/c Backsplash Faucet with 6” Swivel Gooseneck Spout
PART NO. 42226
MANFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
(800)421-6162, FAX: (800)832-8238
www.fisher-mfg.com
REV. A
ANSI/A112.18.1M, ANSI/NSF 61.9
fisher manufacturing company - toll free: 800-421-6162 fax: 800-832-8238
www.fi sher-mfg.com
Installation Instructions for Backsplash Faucets
O
T
O
H
H
T
C
D
O
L
O
L
D
C
BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION
REGARDING BACKFLOW PREVENTION
Installation Instructions Continued
Installation Notes:
• Be sure to shut off water supply before beginning.
• Use pipe thread sealant such as PST on all threaded joints.
• Check the packaging for missing items BEFORE beginning installation. If items are missing,
contact your supplier.
Tools Required for Installation
• Medium Sized Crescent Wrench
PST
• Pipe Thread Sealant
Package Contents
The box should contain the following:
Qty: 1
L
D
O
C
C
O
D
L
Swivel Gooseneck Spout
Length determined by model
Swivel spout includes one 2002 snap ring
Qty: 1
and two 1600-5000 o-rings
1000-8002
Slip Joint Kit
Qty: 2
T
O
H
H
O
T
Control Valve
Installation Instructions
1. Mount control valve body to the backsplash by inserting the nipples through the
backsplash and attaching slip joints. Tighten the slip joints until the control valve
is secure. Be sure to use pipe thread sealant on the nipple threads. Attach elbows
and supply lines as needed. (not Included)
2. Apply lube to the o-rings on the swivel gooseneck spout. Make sure the white snap
ring is in place before mounting the swivel gooseneck spout. Mount the swivel
gooseneck spout and tighten the swivel gooseneck spout nut onto the faucet spout
outlet.
3. Turn on water supply and check for leaks.
10456
Lube
Step 2
Apply O-Ring
Lube Here
Step 3
Step 1
Ø7/8”
Slip Joints
Supply Lines
(not included)
T
O
4”
[101.6mm]
H
H
O
T
L
D
O
C
C
O
D
L
1/2” Elbows
(not included)
Loading...