Fisher 34525 Parts Manual

2924-6000

SPRING

GOOSENECK

2925-6300

HOSE HOOK

2926-3300

PIPE TO HOSE

ADAPTER

2902-12

WALL BRACKET

2600-CV

CONTROL

VALV E

PART NO. 74199

Replacement Parts for Pre-Rinse Units

2914

STAINLESS STEEL

HOSE 36”

2927-4300

3/8” PIPE

21” RISER

2000-7500

SCREW

2000-8000

RED BUTTON

AND

2000-8001

BLUE BUTTON

2000-2301

LEVER HANDLE

2000-3002

BIBB CAP

10464

DUCK GASKET

2000-5000

WASHER

2000-3406

LH CHECK STEM

OR

2000-3407

RH CHECK STEM

2000-6000

SPRING

2000-0001

RETAINER

ASSEMBLY

10456

LUBE

2922-5000

WASHER

2932-0002

WATTS N9
BACK-FLOW
PREVENTER

BACKFLOW

PREVENTER

2913

INSULATED

HANDLE

2949 ULTRA SPRAY

VALV E

2949-9001

SCRUB BRUSH

3000-0000

RH SWIVEL
REPAIR KIT

16” SWING SPOUT

2000-0004

RH CHECK STEM

REPAIR KIT

OR

2000-0005

LH CHECK STEM

REPAIR KIT

[phone], FAX: [phone]

14” SWING SPOUT

12” SWING SPOUT

10” SWING SPOUT

8” SWING SPOUT

6” SWING SPOUT

MANFACTURING COMPANY

PO BOX 60, TULARE, CA 93275

www.fisher-mfg.com

2949-3001

NOZZLE FOR

2949 SPRAY

VALV E

2949-8600

CUP WASHER

1792

ANGLE STOP

WITH KEY

1000-7502

SEAT SCREW

10456

LUBE

SEAT WASHER

3967

3964

3963

3962

3961

3960

2400-2103

ELBOWS

ANGLE STOP

W/ CROSS

HANDLES

RH SWIVEL

2000-5003

2949-9002

BLUE BUMPER

1790-1

3000-0011

STEM

1000-5005

O-RING

2912-2501

2912-7501

2909-6000

10464

DUCK GASKET

2000-5000

WASHER

2000-3002

BIBB CAP

12564

2.2 GPM

AERATOR

1000-5003 WASHER

1000-7502 SCREW

2000-2301

LEVER HANDLE

2000-8000

RED BUTTON

2000-8001

BLUE BUTTON

2901-0000

ADD-ON CONTROL

VALVE LESS SPOUT

15621

SPOUT NUT

2002

SNAP RING

1600-5000

SPOUT

O-RINGS

10456

LUBE

SWIVEL SPOUT

RETRO-FIT KIT

11355

SPRAY VALVE

REPAIR KIT

1000-3301

1000-5001

2912-6000

1000-0001

INCLUDES:

2922-5000

1000-0003

2909-5000

2909-3400

2000-7500

SCREW

AND

19119

REV. A

fisher manufacturing company

4” C/C Backsplash Pre-Rinse Unit

Product Installation Guide

Since 1936, Fisher Manufacturing Company has
manufactured heavy-duty, high quality plumbing
products and hardware specialties for the food service
industry. For three generations, the Fisher family has
adhered to a strict dedication of and overall value.
When you install Fisher products… you install the best.
Our hardware is manufactured with the standardization
of internal mechanisms. All chrome plating is triple
plated copper, nickel and chrome for durability. Every
piece of equipment we make is rigorously tested in
both our modern in-house testing center and in actual
field situations under extreme conditions. Every detail
is thoroughly checked. Before we make our products
available to you, they pass each and every test. You get
proven performance. Guaranteed.

Limited One Year Warranty

Fisher Manufacturing Company warrants its products
and parts thereof (except as noted below) against
defects in materials or workmanship for a period of
one year after the date of original purchase. During
this period Fisher Manufacturing Company will
replace a defective product or part without charge to
you, provided that the entire product is delivered to
Fisher Manufacturing Company. All transportation and
insurance charges for shipping the product to and from
Fisher Manufacturing Company must be borne by you.
Charges for transportation and insurance may, at the
option of Fisher Manufacturing Company, be refunded
depending upon our investigation of the warranty claim.
This warranty does not cover external finish (except at
date of original purchase) or labor costs not specifically
authorized by Fisher Manufacturing Company.

A full and complete copy of our One Year limited
warranty is available upon request.

WARNING:

Proposition 65 requires that we provide you with the
following notice: “This product Contains A Chemical

Known To The State Of California To Cause Birth
Defects Or Other Reproductive Harm.”

KEEP THIS MANUAL FOR FUTURE REFERENCE

fisher manufacturing company - toll free: 800-421-6162 fax: [phone]

#2610 - Pre-Rinse Unit: 4” C/C Backsplash Control

Valve, Ultra Spray

#2610-WB - Pre-Rinse Unit: 4” C/C Backsplash Control-

Valve, Ultra Spray, Wall Bracket

ANSI/A112.18.1M, ANSI/NSF 61.9

www.sher-mfg.com

Installation Instructions for Pre-Rinse Units

BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION
REGARDING BACKFLOW PREVENTION

Installation Notes:

• Be sure to shut off water supply before beginning.

• Use pipe thread sealant such as PST on all threaded joints.

• Check the packaging for missing items BEFORE beginning installation. If items are missing, contact your supplier.

Tools Required for Installation

• Medium Sized Crescent Wrenches

• Pipe Thread Sealant

• Phillips Screwdriver

• 7/16” Drill Bit

• 1/8” Allen Wrench

Installation Instructions

1. If no add-on faucet will be installed, proceed to step

2. If installing an add-on faucet, mount the small
riser to the control valve body using thread sealant.
Thread the add-on faucet to the other end of the
small riser, again using thread sealant.

2. Mount control valve body to the backsplash by insert­ing the nipples through the backsplash and attach­ing slip joints. Tighten the slip joints until the control

valve is secure. Be sure to use pipe thread sealant

on the nipple threads. Attach elbows or supply lines

as needed.

3. Mount the pipe to hose adapter to the enclosed

riser using thread sealant. Mount the other end of
the riser to the female outlet of the add-on body (if
applicable), or the control valve body.

4. If no wall bracket is to be installed, proceed to Step
5, otherwise do the following:

a. Locate and drill a Ø7/16” hole in the wall directly

behind and about 3/4 the way up the riser pipe.

b. Loosely attach the front and back of the pipe

clamp onto the riser pipe.

c. Hold the wall bracket ange against the wall,

centered with the hole. Use the wall screws and a

screw driver to mount the ange to the wall.

d. Slide part, but not all, of the wall bracket rod non-

threaded end rst through the center hole of the
ange and into the wall.

e. Align the rod with the pipe clamp and thread the

rod into the pipe clamp. Be sure the rod is level by
adjusting the pipe clamp position.

f. Once level, x the rod in place by tightening both

the set screw located in the ange and the pipe
clamp screws.

5. Slip the hose hook over the pipe to hose adapter.

Using thread sealant and a crescent wrench, thread

the SS hose into the pipe to hose adapter.

6. Install gooseneck spring by slipping SS hose through
the spring. Spring will t over adapter which holds
it in an upright position. Note: Be sure spring is in-

stalled as shown. DO NOT INSTALL SHORT BEND
DOWN.

7. Fit one of the handle gaskets inside the outlet of the
insulated handle and mount the spray valve onto it.

PST

Step 1

Step 2

Step 3

Ø7/8”

Slip Joints

1/2” Elbows

(not included)

Thread Sealant

Goes Here

4”

[101.6mm]

Thread Sealant

Goes Here

Installation Instructions Continued

8. Fit the other handle gasket inside the inlet of the

insulated handle and mount the handle onto the
SS hose. If installing backow preventer, attach it
between the SS hose and insulated handle. Be sure
that gaskets are used on both sides of the backow

preventer.

9. If installing a brush, do so by pressing brush into the
bumper of the spray valve until secure.

10. To install swing spout to add-on faucet, apply o-ring

lube to the o-rings on the swing spout. Make sure
the white snap ring is in place before mounting the
swing spout. Mount the swing spout and tighten
the swing spout nut onto the add-on faucet spout

outlet.

11. Turn on water supply and check for leaks.

Step 5

Step 6

Spring Bend

On This Side

Thread Sealant

Goes Here

Step 8 Step 9 Step 10 Step 11

Handle Gasket

WATTS N9
BACK-FLOW
PREVENTER

Step 4

Swing Spout

Apply O-Ring

Lube Here

Excess Rod Length

Trim to Fit (optional)

Wall Screw

Set Screw

Pipe

Clamp

Riser Pipe

Step 7

Wall

Handle Gasket