Fisher 3265 Parts Manual

Replacement Parts for Wall Mount Faucets

2000-5003

SEAT WASHER

3200-2306

ECCENTRIC

FLANGES

3967

16” SWING SPOUT

3964

14” SWING SPOUT

8” ADJ. WALL CONTROL VALVE

3200

3963

12” SWING SPOUT

3962

2000-7500

SCREW

2000-8000

RED BUTTON

AND

2000-8001

BLUE BUTTON

2000-2301

LEVER HANDLE

3000-0000

RH SWIVEL STEM

2000-3002

BIBB CAP

10464

DUCK GASKET

2000-5000

WASHER

3000-0010

LH SWIVEL STEM

3000-0011

RH SWIVEL STEM

1000-7502

SCREW

10456

LUBE

3200-2307

1/2” ECCENTRICS

Part No. - 36218 REV.B

REPAIR KIT

3000-0001

LH SWIVEL STEM

REPAIR KIT

ECCENTRIC GASKETS

10” SWING SPOUT

3961

8” SWING SPOUT

3960

6” SWING SPOUT

10014 (24”)

10022 (36””)

SUPPLY LINE

1/2” F X 1/2”F

10049 (24”)

10006 (36””)

SUPPLY LINE 1/2” M X 1/2”F

ANGLE STOP

WITH KEY

ANGLE STOP WITH CROSS

HANDLES

2200-5000

MANUFACTURING COMPANY

PO BOX 60, TULARE, CA 93275

(800)421-6162, FAX: (800)832-8238

www.ﬁ sher-mfg.com

AERATOR

1792

1790-1

12564

2.2 GPM

15621

SPOUT NUT

2002

SNAP RING

1600-5000

SPOUT O-RING

10456

LUBE

19119

SWIVEL SPOUT

RETRO-FIT KIT

2400-2103

ELBOWS

3000-0003

DOUBLE JOINT

SPOUT 7 1/2”

4000-0002

DOUBLE JOINT

SPOUT 14”

2200-0000

SLIP JOINT KIT

FISHER MANUFACTURING COMPANY

8” Adjustable Wall Mount Faucet

Product Installation Guide

Since 1936, Fisher Manufacturing Company has manufactured heavy-duty, high quality plumbing products and hardware specialties for the food service industry. For three generations, the Fisher family has adhered to a strict dedication of and overall value. When you install Fisher products… you install the best. Our hardware is manufactured with the standardization of internal mechanisms. All chrome plating is triple plated copper, nickel and chrome for durability. Every piece of equipment we make is rigorously tested in both our modern in-house testing center and in actual ﬁ eld situations under extreme conditions. Every detail is thoroughly checked. Before we make our products available to you, they pass each and every test. You get proven performance. Guaranteed.

Limited One Year Warranty

Fisher Manufacturing Company warrants its products and parts thereof (except as noted below) against defects in materials or workmanship for a period of one year after the date of original purchase. During this period Fisher Manufacturing Company will replace a defective product or part without charge to you, provided that the entire product is delivered to Fisher Manufacturing Company. All transportation and insurance charges for shipping the product to and from Fisher Manufacturing Company must be borne by you. Charges for transportation and insurance may, at the option of Fisher Manufacturing Company, be refunded depending upon our investigation of the warranty claim. This warranty does not cover external ﬁ nish (except at date of original purchase) or labor costs not speciﬁ - cally authorized by Fisher Manufacturing Company.

A full and complete copy of our One Year limited warranty is available upon request.

WARNING:

Proposition 65 requires that we provide you with the following notice: “This product Contains A Chemical

Known To The State Of California To Cause Birth Defects Or Other Reproductive Harm.”

FISHER MANUFACTURING COMPANY, TOLL FREE: 800-421-6162, FAX:800-832-8238

www.ﬁ sher-mfg.com

#3250 - 8” Adj. Wall Mount Faucet with 6” Swing Spout #3251- 8” Adj. Wall Mount Faucet with 8” Swing Spout #3252 - 8” Adj. Wall Mount Faucet with 10” Swing Spout #3253 - 8” Adj. Wall Mount Faucet with 12” Swing Spout #3254 - 8” Adj. Wall Mount Faucet with 14” Swing Spout #9102 - 8” Adj. Wall Mount Faucet with 16” Swing Spout

ANSI/A112.18.1M, ANSI/NSF 61.

Installation Instructions for Wall Mount Faucet

Installation Instructions Continued

BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION REGARDING BACKFLOW PREVENTION.

Installation Notes:

• Be sure water supply is shut-off before beginning.

• Use pipe thread sealant on all threaded joints such as PST or Teﬂ on tape.

• Check the packaging for missing items BEFORE beginning installation. If items are missing, contact your supplier.

Package Contents

The box should contain the following:

3200

8” Adj. Control Valve

Swing Spout

Length determined by model

Each spout includes one 2002

snap ring and two 1600-5000

Qty:1

O-rings

3200-2306

Eccentric Flanges

Qty: 2

3200-2307

1/2” Eccentrics

Qty: 2

2200-5000

Eccentrics Gaskets

Qty: 2

Items needed for Installation

• 1 - Medium Sized Crescent Wrenches

• 1 - Plumbers Tape or Pipe Thread Sealant

Installation Instructions

Step 1.

After unpacking items and checking for missing components, insert and center the gasket into the female swivel inlets of the 8” control valve body. Loosely mount the eccentrics and ﬂ ange onto the control valve body.

10456

Lube

Qty: 1

Step 2

Ø 7/8”

Step 3

Elbows

(Not Included)

DJ Swing Spout

1/2” NPT Supply Nipples (Not Included)

7 3/4” - 8 1/4”

[196.9mm] - [209.6mm]

1/2” NPT Supply Nipples (Not Included)

7 3/4” - 8 1/4”

[196.9mm] - [209.6mm]

Step 4

Supply Lines

(Not Included)

Swing Spout

Step 2.

Mount control valve body to either a wall with a male supply nipples, or backsplash with nipples (not included). Be sure to use pipe thread sealant on the supply nipple threads. Adjust the eccentrics as needed in order to mount the control valve level. Once level, tighten the eccentrics

Step 3. Optional DJ swivel spout, apply lube to the O-ring on the spout. Mount the DJ swivel spout and tighten the nut onto the faucet spout outlet.

Step 4.

Apply O-ring lube to the O-rings on the swing spout. Make sure the white snap ring is in place before mounting the swing spout. Mount the swing spout and tighten the swing spout nut onto the faucet spout outlet.

Step 5.

Turn on water supply and check for leaks.

Step 1

Gasket

Eccentric

Flange

Step 5

Apply O-ring Lube Here