Fisher 3254 Parts Manual
Replacement Parts for Wall Mount Faucets
2000-5003
SEAT WASHER
8” ADJ. WALL CONTROL VALVE
3200
2000-7500
SCREW
2000-8000
RED BUTTON
AND
2000-8001
BLUE BUTTON
2000-2301
LEVER HANDLE
2000-3002
BIBB CAP
73657
DUCK GASKET
2000-5000
WASHER
3000-0010
LH SWIVEL STEM
OR
3000-0011
RH SWIVEL STEM
1000-7502
SCREW
73521
LUBE
3000-0000
RH SWIVEL STEM
REPAIR KIT
OR
3000-0001
LH SWIVEL STEM
REPAIR KIT
10022 (36””)
SUPPLY LINE
1/2” F X 1/2”F
10006 (36””)
SUPPLY LINE
1/2” M X 1/2”F
3967
16” SWING SPOUT
3964
14” SWING SPOUT
3963
12” SWING SPOUT
3962
10” SWING SPOUT
3961
8” SWING SPOUT
3960
6” SWING SPOUT
1792
ANGLE STOP
WITH KEY
1790-1
ANGLE STOP
WITH CROSS
HANDLES
12564
2.2 GPM
AERATOR
15621
SPOUT NUT
2002
SNAP RING
1600-5000
SPOUT
O-RING
73521
LUBE
19119
SWIVEL SPOUT
RETRO-FIT KIT
2400-2103
ELBOWS
3000-0003
DOUBLE JOINT
SPOUT 7 1/2”
OR
4000-0002
DOUBLE JOINT
SPOUT 14”
FISHER MANUFACTURING COMPANY
8” Adjustable Wall Mount Faucet
Product Installation Guide
Since 1936, Fisher Manufacturing Company has
manufactured heavy-duty, high quality plumbing products
and hardware specialties for the food service industry.
For three generations, the Fisher family has adhered to a
strict dedication of and overall value. When you install
Fisher products… you install the best. Our hardware
is manufactured with the standardization of internal
mechanisms. All chrome plating is triple plated copper,
nickel and chrome for durability. Every piece of equipment
we make is rigorously tested in both our modern in-house
testing center and in actual field situations under extreme
conditions. Every detail is thoroughly checked. Before
we make our products available to you, they pass each
and every test. You get proven performance. Guaranteed.
Limited One Year Warranty
Fisher Manufacturing Company warrants its products and
parts thereof (except as noted below) against defects in
materials or workmanship for a period of one year after
the date of original purchase. During this period Fisher
Manufacturing Company will replace a defective product
or part without charge to you, provided that the entire
product is delivered to Fisher Manufacturing Company.
All transportation and insurance charges for shipping the
product to and from Fisher Manufacturing Company must
be borne by you. Charges for transportation and insurance
may, at the option of Fisher Manufacturing Company, be
refunded depending upon our investigation of the warranty
claim. This warranty does not cover external finish
(except at date of original purchase) or labor costs not
specifically authorized by Fisher Manufacturing Company.
A full and complete copy of our One Year limited warranty
is available upon request.
Warning:This product can expose you to chemicals
including Lead, Nickel (Metallic), Di(2-ethylhexyl)
phathalate (DEHP) which are known to the State of
California to cause cancer, and Lead. Di(2-ethylhexyl)
phathalate (DEHP) which are known to the State of
Califorina to cause birth defects or reproductive harm.
For more information go to:
www.P65Warnings.ca.gov.
#3250 - 8” Adj. Wall Mount Faucet with 6” Swing
Spout
#3251- 8” Adj. Wall Mount Faucet with 8” Swing
Spout
#3252 - 8” Adj. Wall Mount Faucet with 10” Swing
Spout
#3253 - 8” Adj. Wall Mount Faucet with 12” Swing
Spout
#3254 - 8” Adj. Wall Mount Faucet with 14” Swing
Spout
#9102 - 8” Adj. Wall Mount Faucet with 16” Swing
Spout
3200-2306
ECCENTRIC
FLANGES
3200-2307
1/2” ECCENTRICS
Part No. - 36218 REV.B
2200-5000
ECCENTRIC GASKETS
MANUFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
(800)421-6162, FAX: (800)832-8238
www.fi sher-mfg.com
2200-0000
SLIP JOINT KIT
ANSI/A112.18.1M, ANSI/NSF 61.
FISHER MANUFACTURING COMPANY, TOLL FREE: 800-421-6162, FAX:800-832-8238
www.fi sher-mfg.com
9
Installation Instructions for Wall Mount Faucet
Installation Instructions Continued
BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING
JURISDICTION REGARDING BACKFLOW PREVENTION.
Installation Notes:
• Be sure water supply is shut-off before beginning.
• Use pipe thread sealant on all threaded joints such as PST or Tefl on tape.
• Check the packaging for missing items BEFORE beginning installation. If
items are missing, contact your supplier.
Package Contents
The box should contain the following:
3200
8” Adj. Control Valve
Swing Spout
Length determined by model
Each spout includes one 2002
snap ring and two 1600-5000
Qty:1
O-rings
3200-2306
Eccentric Flanges
Qty: 2
3200-2307
1/2” Eccentrics
Qty: 2
2200-5000
Eccentrics Gaskets
Qty: 2
Items needed for Installation
• 1 - Medium Sized Crescent Wrenches
• 1 - Plumbers Tape or Pipe Thread Sealant
Installation Instructions
Step 1.
After unpacking items and checking for missing components, insert and center the gasket into the
female swivel inlets of the 8” control valve body. Loosely mount the eccentrics and fl ange onto the
control valve body.
73521
Lube
Qty: 1
Step 2
Ø 7/8”
Step 3
Elbows
(Not Included)
DJ Swing Spout
1/2” NPT Supply
Nipples (Not Included)
7 3/4” - 8 1/4”
[196.9mm] - [209.6mm]
1/2” NPT Supply
Nipples (Not Included)
7 3/4” - 8 1/4”
[196.9mm] - [209.6mm]
Step 4
Supply Lines
(Not Included)
Swing Spout
Step 2.
Mount control valve body to either a wall with a male supply nipples, or backsplash with nipples (not
included). Be sure to use pipe thread sealant on the supply nipple threads. Adjust the eccentrics as
needed in order to mount the control valve level. Once level, tighten the eccentrics
Step 3.
Optional DJ swivel spout, apply lube to the O-ring on the spout. Mount the DJ swivel spout and
tighten the nut onto the faucet spout outlet.
Step 4.
Apply O-ring lube to the O-rings on the swing spout. Make sure the white snap ring is in place before
mounting the swing spout. Mount the swing spout and tighten the swing spout nut onto the faucet
spout outlet.
Step 5.
Turn on water supply and check for leaks.
Step 1
Gasket
Eccentric
Flange
Step 5
Apply O-ring
Lube Here
Apply O-ring
Lube Here
Loading...