Fisher 27499 Parts Manual
2924-6000
SPRING
GOOSENECK
2925-6300
HOSE HOOK
2926-3300
PIPE TO HOSE
ADAPTER
2902-12
WALL BRACKET
2600-CV
CONTROL
VALV E
PART NO. 74199
Replacement Parts for Pre-Rinse Units
2914
STAINLESS STEEL
HOSE 36”
2927-4300
3/8” PIPE
21” RISER
2000-7500
SCREW
2000-8000
RED BUTTON
AND
2000-8001
BLUE BUTTON
2000-2301
LEVER HANDLE
2000-3002
BIBB CAP
10464
DUCK GASKET
2000-5000
WASHER
2000-3406
LH CHECK STEM
OR
2000-3407
RH CHECK STEM
2000-6000
SPRING
2000-0001
RETAINER
ASSEMBLY
10456
LUBE
2922-5000
WASHER
2932-0002
WATTS N9
BACK-FLOW
PREVENTER
BACKFLOW
PREVENTER
2913
INSULATED
HANDLE
2949 ULTRA SPRAY
VALV E
2949-9001
SCRUB BRUSH
3000-0000
RH SWIVEL
REPAIR KIT
16” SWING SPOUT
2000-0004
RH CHECK STEM
REPAIR KIT
OR
2000-0005
LH CHECK STEM
REPAIR KIT
(800)421-6162, FAX: (800)832-8238
14” SWING SPOUT
12” SWING SPOUT
10” SWING SPOUT
8” SWING SPOUT
6” SWING SPOUT
MANFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
www.fisher-mfg.com
2949-3001
NOZZLE FOR
2949 SPRAY
VALV E
2949-8600
CUP WASHER
1792
ANGLE STOP
WITH KEY
1000-7502
SEAT SCREW
10456
LUBE
SEAT WASHER
3967
3964
3963
3962
3961
3960
2400-2103
ELBOWS
ANGLE STOP
W/ CROSS
HANDLES
RH SWIVEL
2000-5003
2949-9002
BLUE BUMPER
1790-1
3000-0011
STEM
1000-5005
O-RING
2912-2501
2912-7501
2909-6000
10464
DUCK GASKET
2000-5000
WASHER
2000-3002
BIBB CAP
12564
2.2 GPM
AERATOR
1000-5003 WASHER
1000-7502 SCREW
2000-2301
LEVER HANDLE
2000-8000
RED BUTTON
2000-8001
BLUE BUTTON
2901-0000
ADD-ON CONTROL
VALVE LESS SPOUT
15621
SPOUT NUT
2002
SNAP RING
1600-5000
SPOUT
O-RINGS
10456
LUBE
SWIVEL SPOUT
RETRO-FIT KIT
11355
SPRAY VALVE
REPAIR KIT
1000-3301
1000-5001
2912-6000
1000-0001
INCLUDES:
2922-5000
1000-0003
2909-5000
2909-3400
2000-7500
SCREW
AND
19119
REV. A
fisher manufacturing company
4” C/C Backsplash Pre-Rinse Unit
Product Installation Guide
Since 1936, Fisher Manufacturing Company has
manufactured heavy-duty, high quality plumbing
products and hardware specialties for the food service
industry. For three generations, the Fisher family has
adhered to a strict dedication of and overall value.
When you install Fisher products… you install the best.
Our hardware is manufactured with the standardization
of internal mechanisms. All chrome plating is triple
plated copper, nickel and chrome for durability. Every
piece of equipment we make is rigorously tested in
both our modern in-house testing center and in actual
field situations under extreme conditions. Every detail
is thoroughly checked. Before we make our products
available to you, they pass each and every test. You get
proven performance. Guaranteed.
Limited One Year Warranty
Fisher Manufacturing Company warrants its products
and parts thereof (except as noted below) against
defects in materials or workmanship for a period of
one year after the date of original purchase. During
this period Fisher Manufacturing Company will
replace a defective product or part without charge to
you, provided that the entire product is delivered to
Fisher Manufacturing Company. All transportation and
insurance charges for shipping the product to and from
Fisher Manufacturing Company must be borne by you.
Charges for transportation and insurance may, at the
option of Fisher Manufacturing Company, be refunded
depending upon our investigation of the warranty claim.
This warranty does not cover external finish (except at
date of original purchase) or labor costs not specifically
authorized by Fisher Manufacturing Company.
A full and complete copy of our One Year limited
warranty is available upon request.
WARNING:
Proposition 65 requires that we provide you with the
following notice: “This product Contains A Chemical
Known To The State Of California To Cause Birth
Defects Or Other Reproductive Harm.”
KEEP THIS MANUAL FOR FUTURE REFERENCE
fisher manufacturing company - toll free: 800-421-6162 fax: 800-832-8238
#2610 - Pre-Rinse Unit: 4” C/C Backsplash Control
Valve, Ultra Spray
#2610-WB - Pre-Rinse Unit: 4” C/C Backsplash Control-
Valve, Ultra Spray, Wall Bracket
ANSI/A112.18.1M, ANSI/NSF 61.9
www.sher-mfg.com
Installation Instructions for Pre-Rinse Units
BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION
REGARDING BACKFLOW PREVENTION
Installation Notes:
• Be sure to shut off water supply before beginning.
• Use pipe thread sealant such as PST on all threaded joints.
• Check the packaging for missing items BEFORE beginning installation. If items are missing, contact your supplier.
Tools Required for Installation
• Medium Sized Crescent Wrenches
• Pipe Thread Sealant
• Phillips Screwdriver
• 7/16” Drill Bit
• 1/8” Allen Wrench
Installation Instructions
1. If no add-on faucet will be installed, proceed to step
2. If installing an add-on faucet, mount the small
riser to the control valve body using thread sealant.
Thread the add-on faucet to the other end of the
small riser, again using thread sealant.
2. Mount control valve body to the backsplash by inserting the nipples through the backsplash and attaching slip joints. Tighten the slip joints until the control
valve is secure. Be sure to use pipe thread sealant
on the nipple threads. Attach elbows or supply lines
as needed.
3. Mount the pipe to hose adapter to the enclosed
riser using thread sealant. Mount the other end of
the riser to the female outlet of the add-on body (if
applicable), or the control valve body.
4. If no wall bracket is to be installed, proceed to Step
5, otherwise do the following:
a. Locate and drill a Ø7/16” hole in the wall directly
behind and about 3/4 the way up the riser pipe.
b. Loosely attach the front and back of the pipe
clamp onto the riser pipe.
c. Hold the wall bracket ange against the wall,
centered with the hole. Use the wall screws and a
screw driver to mount the ange to the wall.
d. Slide part, but not all, of the wall bracket rod non-
threaded end rst through the center hole of the
ange and into the wall.
e. Align the rod with the pipe clamp and thread the
rod into the pipe clamp. Be sure the rod is level by
adjusting the pipe clamp position.
f. Once level, x the rod in place by tightening both
the set screw located in the ange and the pipe
clamp screws.
5. Slip the hose hook over the pipe to hose adapter.
Using thread sealant and a crescent wrench, thread
the SS hose into the pipe to hose adapter.
6. Install gooseneck spring by slipping SS hose through
the spring. Spring will t over adapter which holds
it in an upright position. Note: Be sure spring is in-
stalled as shown. DO NOT INSTALL SHORT BEND
DOWN.
7. Fit one of the handle gaskets inside the outlet of the
insulated handle and mount the spray valve onto it.
PST
Step 1
Step 2
Step 3
Ø7/8”
Slip Joints
1/2” Elbows
(not included)
Thread Sealant
Goes Here
4”
[101.6mm]
Thread Sealant
Goes Here
Installation Instructions Continued
8. Fit the other handle gasket inside the inlet of the
insulated handle and mount the handle onto the
SS hose. If installing backow preventer, attach it
between the SS hose and insulated handle. Be sure
that gaskets are used on both sides of the backow
preventer.
9. If installing a brush, do so by pressing brush into the
bumper of the spray valve until secure.
10. To install swing spout to add-on faucet, apply o-ring
lube to the o-rings on the swing spout. Make sure
the white snap ring is in place before mounting the
swing spout. Mount the swing spout and tighten
the swing spout nut onto the add-on faucet spout
outlet.
11. Turn on water supply and check for leaks.
Step 5
Step 6
Spring Bend
On This Side
Thread Sealant
Goes Here
Step 8 Step 9 Step 10 Step 11
Handle Gasket
WATTS N9
BACK-FLOW
PREVENTER
Step 4
Swing Spout
Apply O-Ring
Lube Here
Excess Rod Length
Trim to Fit (optional)
Wall Screw
Set Screw
Pipe
Clamp
Riser Pipe
Step 7
Wall
Handle Gasket
Loading...