Fisher 2740 Parts List
Replacement Parts for Pot Filler
2931
SWIVEL HOSE
ADAPTER
2932
SWIVEL HOSE
ADAPTER
WITH VACUUM
BREAKER
2000-5003
SEAT WASHER
PART NO. 39446
2907
WALL HOOK
3700
CONTROL VALVE
2542
BACKFLOW
PREVENTER
WATTSN9
BACK-FLOW
PREVENTER
2000-7500
SCREW
2000-8000
RED BUTTON
AND
2000-8001
BLUE BUTTON
2000-2301
LEVER HANDLE
2000-3002
BIBB CAP
10464
DUCK GASKET
2000-5000
WASHER
3000-0011
RH SWIVEL STEM
1000-7502
SCREW
10456
LUBE
11061
POT FILLER
VALVE
2913
INSULATED
HANDLE
2922-5000
WASHER
2915-FG
60” FOODGRADE
HOSE
1790-1
ANGLE STOP
WITH CROSS
HANDLE
ANGLE STOP
WITH KEY
2200-0000
NIPPLE KIT
3000-0000
RH SWIVEL STEM
REPAIR KIT
10014 (24”)
10022 (36”)
SUPPLY LINE
1/2” F X 1/2” F
10049 (24”)
10006 (36”)
SUPPLY LINE
1/2” M X 1/2” F
MANFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
(800)421-6162, FAX: (800)832-8238
www.fisher-mfg.com
1000-5005
O-RING
1792
2400-2103
ELBOWS
2912-2501
2912-7501
2909-6000
3967
16” SWING SPOUT
3964
14” SWING SPOUT
3963
12” SWING SPOUT
3962
10” SWING SPOUT
3961
8” SWING SPOUT
3960
6” SWING SPOUT
12564
2.2 GPM
AERATOR
11355
SPRAY VALVE
REPAIR KIT
1000-3301
1000-5001
2912-6000
1000-0001
INCLUDES:
1000-5003 WASHER
1000-7502 SCREW
2922-5000
1000-0003
2909-5000
2909-3400
2901-0000
ADD-ON CONTROL
VALVE LESS SPOUT
15621
SPOUT NUT
2002
SNAP RING
1600-5000
SPOUT
O-RINGS
10456
LUBE
19119
SWIVEL SPOUT
RETRO-FIT KIT
REV. A
fisher manufacturing company
Single Wall Mount Pot Filler
Product Installation Guide
Since 1936, Fisher Manufacturing Company has
manufactured heavy-duty, high quality plumbing
products and hardware specialties for the food service
industry. For three generations, the Fisher family has
adhered to a strict dedication of and overall value.
When you install Fisher products… you install the best.
Our hardware is manufactured with the standardization
of internal mechanisms. All chrome plating is triple
plated copper, nickel and chrome for durability.
Every piece of equipment we make is rigorously
tested in both our modern in-house testing center and
in actual fi eld situations under extreme conditions.
Every detail is thoroughly checked. Before we make
our products available to you, they pass each and
every test. You get proven performance. Guaranteed.
Limited One Year Warranty
Fisher Manufacturing Company warrants its products
and parts thereof (except as noted below) against
defects in materials or workmanship for a period of
one year after the date of original purchase. During
this period Fisher Manufacturing Company will
replace a defective product or part without charge to
you, provided that the entire product is delivered to
Fisher Manufacturing Company. All transportation and
insurance charges for shipping the product to and from
Fisher Manufacturing Company must be borne by you.
Charges for transportation and insurance may, at the
option of Fisher Manufacturing Company, be refunded
depending upon our investigation of the warranty claim.
This warranty does not cover external fi nish (except at
date of original purchase) or labor costs not specifi cally
authorized by Fisher Manufacturing Company.
A full and complete copy of our One Year limited
warranty is available upon request.
WARNING:
Proposition 65 requires that we provide you with the
following notice: “This product Contains A Chemical
Known To The State Of California To Cause Birth
Defects Or Other Reproductive Harm.”
KEEP THIS MANUAL FOR FUTURE REFERENCE
fisher manufacturing company - toll free: 800-421-6162 fax: 800-832-8238
#2740 - Pot Filler: Single Wall Mount Control Valve with
Vacuum Breaker and Wall Hook
#2750 - Pot Filler: Single Wall Mount Control Valve with
Swivel Hose Adapter and Wall Hook
ANSI/A112.18.1M, ANSI/NSF 61.9
www.fi sher-mfg.com
Installation Instructions for Pot Filler
A112.18.1M
BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION
REGARDING BACKFLOW PREVENTION
Installation Notes:
• Be sure to shut off water supply before beginning.
• Use pipe thread sealant such as PST on all threaded joints.
• Check the packaging for missing items BEFORE beginning installation. If items are missing, contact your supplier.
Tools Required for Installation
• Medium Sized Crescent Wrench
• Pipe Thread Sealant
• Phillips Screwdriver
Installation Instructions
1. If no add-on faucet will be installed, proceed to step
2. If installing an add-on faucet, mount the small
riser to the control valve body using thread sealant.
Thread the add-on faucet to the other end of the
small riser, again using thread sealant.
2. Mount control valve body to either a wall with male
supply nipples, or a backsplash with nipples (not
included). Be sure to use pipe thread sealant on the
supply nipple threads.
3. Mount either the swivel hose adapter with vacuum
breaker (2932) or swivel hose adapter without
vacuum breaker (2931) to control valve body. Use
lube on the o-rings on the swivel hose adapter and
be sure white snap ring is in place. Tighten nut until
swivel hose adapter is secure.
4. If installing a backfl ow preventer, do so by applying
thread sealant and inserting into the swivel hose
adapter, tightening until secure. Be sure that arrows
on backfl ow preventer are pointing in direction of
fl ow. Using pipe thread sealant, insert the stainless
steel hose into either the backfl ow preventer or the
swivel hose adapter and tighten nut until secure.
5. Fit one of the handle gaskets inside the outlet of the
insulated handle and mount the pot fi ller valve onto
it. Fit the other handle gasket inside the inlet of the
insulated handle and mount the handle onto the
stainless steel hose. Be sure that gaskets are used
on both sides of the insulated handle.
6. To install the wall bracket, determine a good
location and hold fi rmly against the wall. Using a
screwdriver, insert the three screws through the
holes in the wall hook and screw into the wall.
7. To install swing spout to add-on faucet, apply lube
to the o-rings on the swing spout. Make sure the
white snap ring is in place before mounting the
swing spout. Mount the swing spout and tighten the
swing spout nut onto the add-on faucet spout outlet
8. Turn on water supply and check for leaks.
PST
Step 1
Thread Sealant
Goes Here
Step 2
1/2” NPT Supply
Nipples (not included)
Installation Instructions Continued
Step 3
2932
Swivel Hose
Adapter with
Vacuum Breaker
Apply O-Ring
Lube Here
Step 5
Handle Gasket
Step 7 Step 8
Swing Spout
Apply O-Ring
Lube Here
Step 4
Step 6
Thread Sealant
Goes Here
WATTSN9
BACK-FLOW
PREVENTER
Ø7/8”
Loading...