Fisher 25135 Parts Manual

Spray Valve and Accessories
Model 2949 Spray Valve
Cast red brass construction with polished chrome fi nish. Inlet thread size fi t Fisher and all other pre-rinse units. Squeeze lever is insulated for operator safety. Large, vinyl dish guard bumper accommodates optional snap-in scrubbing brush.
2949-3001
Nozzle for
2949 Spray
Valve
Model 2902-12 Wall Bracket
Designed to brace riser pipe, Chrome plated nish, Adjustable - 2 1/4” to 12”. (Cut off adjusting rod for correct length.
Model 2911 Hose and Spray Assembly
Overall length 46”. Note: Upon request, optional adapter for inlet is available to fi t other pre-rinse units.
Stainless Steel Armor Clad Flex Hose
Model 2914 - “A” = 36” (Fits Model 2010 Pre-rinse Unit) Model 2916 -25 1/2” - “A” = 25 1/2” (Fits Model 2211 Pre-rinse Unit) Model 2916 - 15 1/2” - “A” = 15” (Fits Model 2916 - 15 1/2” Pre-rinse Unit) Model 2918 - 44” Replacement Pre-rinse hose with T&S adapter. Also available in 68” for T&S sprays.
Model 2913 Insulated Handle
3/4” 14 Female
1/4” NPT Male Stainless Steel
1/4” NPT Male
Fisher Handle Thread
2912-2501
Squeeze Lever
Dish Guard Bumper
Vinyl Insulation
2914
Fisher and T&S Valve Thread
1000-3301
Bonnet Nut
1000-5001
Bonnet Washer
2912-6000
Spring
1000-0001
Retainer Disk Assy
2922-5000
Handle Gasket
1000-0003
Lift Pin Sa
2909-5000
Gasket
2909-3400
Lift Pin Guide
2912-7501
Screws
2909-6000
Clip
3/4” Insulated Handle
200 P.S.I. 3- Ply Hose Liner
Stainless Steel Cover
2918
T&S Spring Stop
Thread
3/4” 14 Female
11355
Spray Valve
Repair Kit
fisher manufacturing company
Pre-Rinse Units
Product Installation Guide
Since 1936, Fisher Manufacturing Company has manufactured heavy-duty, high quality plumbing products and hardware specialties for the food service industry. For three generations, the Fisher family has adhered to a strict dedication of and overall value. When you install Fisher products… you install the best. Our hardware is manufactured with the standardization of internal mechanisms. All chrome plating is triple plated copper, nickel and chrome for durability. Every piece of equipment we make is rigorously tested in both our modern in-house testing center and in actual fi eld situations under extreme conditions. Every detail is thoroughly checked. Before we make our products available to you, they pass each and every test. You get proven performance. Guaranteed.
Limited One Year Warranty
Fisher Manufacturing Company warrants its products and parts thereof (except as noted below) against defects in materials or workmanship for a period of one year after the date of original purchase. During this period Fisher Manufacturing Company will replace a defective product or part without charge to you, provided that the entire product is delivered to Fisher Manufacturing Company. All transportation and insurance charges for shipping the product to and from Fisher Manufacturing Company must be borne by you. Charges for transportation and insurance may, at the option of Fisher Manufacturing Company, be refunded depending upon our investigation of the warranty claim. This warranty does not cover external fi nish (except at date of original purchase) or labor costs not specifi cally authorized by Fisher Manufacturing Company.
A full and complete copy of our One Year limited warranty is available upon request.
WARNING:
Proposition 65 requires that we provide you with the following notice: “This product Contains A Chemical
Known To The State Of California To Cause Birth Defects Or Other Reproductive Harm.”
KEEP THIS MANUAL FOR FUTURE REFERENCE
PART NO. L9417
MANFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
(800)421-6162, FAX: (800)832-8238
www.fisher-mfg.com
REV. A
ANSI/A112.18.1M, ANSI/NSF 61.9
fisher manufacturing company - toll free: 800-421-6162 fax: 800-832-8238
www.fi sher-mfg.com
Installation Instructions for All Models
#2924-6000
1. Install MIXING FAUCET.
2. Install 2927-4300 PIPE RISER and
2926-3300 PIPE TO HOSE ADAPTER.
Into mixing faucet. Note: Use pipe Sealant compound on both joints.
3. Slip 2925-6300 HOSE HOOK over
2926-3300 ADAPTER.
4. Install 2914 FLEX HOSE into 2926-3300 ADAPTER. Note: Use pipe sealant compound.
5. Install 2924-6000 SPRING GOOSE­NECK by slipping 2914 FLEX HOSE through the spring. Spring will fit over
2926-3300 ADAPTER which holds it in
an upright position. Note: Be sure spring is installed as shown. DO NOT INSTALL SHORT BEND DOWN.
6. Install 2913 INSULATED HANDLE with hex end toward spray valve. Note: Be sure internal gaskets are in place for both hose and spray valve end of handle.
NOTICE TO PLUMBER:
It is not necessary to install check valves in supply lines to prevent cross flow of hot and cold water. All Fisher Mixing Faucets are supplied with internal check valves.
To insure long, maintenance free service and efficiency from your Fisher Pre-Rinse unit, we note the following.
1. Whenever possible install 2902-12 WALL BRACKET. This prevents the bending of the pipe riser by the operator.
2. The spray valve is provided with a spring clip which when placed in the squeeze handle notch allows the spray to run freely. This allows the operator to use both hands for pre-rinsing etc.
3. To avoid accidental flooding and increase hose life, relieve pressure on the hose during slack periods and at closing time by first turning off mixing faucet (or water supply) then squeezing the lever handle.
Spring
Gooseneck
2926-3300
Pipe To Hose
Adapter
#2927-4300
3/8” Pipe 21” Riser
2020-0006
Ultra-Flex Gooseneck
1000-5008
O-Ring
2929-2500
Packing Gland
2927-4301
31” Riser
2020-7000
2020-7000
Set Screw
Set Screw
ULTRA-FLEX
PRE-RINSE
UNIT
2020-7000
Set Screw
2949 Ultra-Spay Valve
2922-5000
Washer
2925-6300
Hose Hook
2902-12
Wall Bracket
2020-5003
Gasket
2020-5003
Gasket
2020-5004
Gasket
2020-5002
O-Ring
2916-15 ½ 15 ½” Hose
2922-5000
Gasket
2913-3/8
3/8” Handle
#2914
Stainless Steel
36” Hose
OPTION
#2932-0002
In-Line
Dual Check
Valve
#2913
Insulated
Handle
2949
Ultra-Spray
Optional 2901
Add-On Faucet
2020-5004
Gasket
1700-5002
O-Ring
2020-5002
O-Ring
1700-5002
O-Ring
Optional
2949-9001
Brush
A
E
A #2700 – Single Wall Control Valve w/ 3/8”F outlet Stem RH Swivel Repair Kit #3000-0000
B #13196 – 8” c/c Backsplash Control Valve w/ 3/8”F outletand check valves Hot Stem RH Check Repair Kit #2000-0004
Cold Stem LH Check Repair Kit #2000-0005
C #2500-CV – 4” c/c Deck Control Valve w/ 3/8”F outlet, check valves Hot Stem RH Check Repair Kit #2000-0004
Cold Stem LH Check Repair Kit #2000-0005
D #12890 – Single Deck Control Valve w/ 3/8”F outlet
Stem LH Swivel Repair Kit #3000-0001
2020-0004
Ultra-Swivel W/Handle
2000-3406
LH Check Stem
2000-3407
RH Check Stem
2000-6000
Spring
2000-5003 Seat Washer
1000-7502 Screw
2000-7500
Screw
2000-8000
2000-8000
Red Button
Red Button And
And
2000-8001 2000-8001
Blue Button Blue Button
2000-2301
Handle
2000-3002
Bibb Cap
10464
Gasket
2000-5000
Washer
2000-0001
Retainer Assembly
B
F
E #2300-CV – 8” c/c Deck Control Valve w/ 3/8”F outlet, check valves
Hot Stem RH Check Repair Kit #2000-0004 Cold Stem LH Check Repair Kit #2000-0005
F #2600-CV – 4” c/c Backsplash Control Valve w/ 3/8” F outlet, check valves
Hot Stem RH Check Repair Kit #2000-0005 Cold Stem LH Check Repair Kit #2000-0004
G #2200-CV – 8” adj Wall Control Valve w/ 3/8”F outlet and check valves
Hot Stem RH Check Repair Kit #2000-0004 Cold Stem LH Check Repair Kit #2000-0005
H #13080 – Single Deck Dual Control Valve w/ 3/8” F outlet, check valves
Hot Stem RH Check Repair Kit #2000-0004
2000-7500
Screw
2000-8000
Red Button And
2000-0004
RH Check Stem
Repair Kit
Or
2000-0005
LH Check Stem
Repair Kit
3000-0000
3000-0000
RH Swivel Stem
RH Swivel Stem
Repair Kit
Repair Kit
Or
Or
3000-0001
3000-0001
LH Swivel Stem
LH Swivel Stem
Repair Kit
Repair Kit
2000-8001
Blue Button
2000-2301
Handle
2000-3002
Bibb Cap
10464
Gasket
2000-5000
Washer
C
G
2000-5003 Seat Washer
1000-7502 Screw
-
H
3000-0010
LH Swivel Stem
r
3000-0011
RH Swivel Stem
D
Loading...