Fisher 2260 Parts Manual
Replacement Parts for Utility Spray
2931
SWIVEL HOSE
ADAPTER
2932
SWIVEL HOSE
ADAPTER
WITH VACUUM
BREAKER
10014 (24”)
10022 (36”)
SUPPLY LINE
1/2” F X 1/2” F
10049 (24”)
10006 (36”)
SUPPLY LINE
1/2” M X 1/2” F
PART NO. 39454
WALL HOOK
2949-9001
BACKFLOW
PREVENTER
3200-CV
CONTROL VALVE
2000-7500
SCREW
2000-8000
RED BUTTON
2000-8001
BLUE BUTTON
2000-2301
LEVER HANDLE
2000-3002
BIBB CAP
DUCK GASKET
2000-5000
WASHER
2000-3406
LH CHECK STEM
2000-3407
RH CHECK STEM
2000-6000
SPRING
2000-0001
RETAINER
ASSEMBLY
2907
BRUSH
2542
AND
10464
OR
10456
LUBE
WATTSN9
BACK-FLOW
PREVENTER
SEAT SCREW
3000-0000
RH SWIVEL
REPAIR KIT
2000-0004
RH CHECK STEM
REPAIR KIT
OR
2000-0005
LH CHECK STEM
REPAIR KIT
3200-2306
ECCENTRIC
FLANGES
MANFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
(800)421-6162, FAX: (800)832-8238
10456
LUBE
16” SWING SPOUT
14” SWING SPOUT
12” SWING SPOUT
10” SWING SPOUT
8” SWING SPOUT
6” SWING SPOUT
3200-2307
1/2” ECCENTRICS
1790-1
ANGLE STOP
WITH CROSS
HANDLE
1792
ANGLE STOP
WITH KEY
www.fisher-mfg.com
2920
UTILITY SPRAY
VALVE
2913
INSULATED
HANDLE
2922-5000
WASHER
2915
60” HOSE
11355
SPRAY VALVE
REPAIR KIT
1000-7502
2000-5003
SEAT WASHER
3967
3964
3963
3962
3961
3960
3000-0011
RH SWIVEL
STEM
2200-5000
ECCENTRIC
GASKETS
1000-3301
BONNET NUT
2912-6000
SPRING
1000-5003
SEAT WASHER
1000-7502
SCREW
1000-0003
LIFT PIN
SUBASSEMBLY
2909-5000
GASKET
2912-2501
SWUEEZE
LEVER
2912-7501
SCREWS
2909-6000
CLIP
10464
DUCK GASKET
2000-5000
WASHER
2.2 GPM
AERATOR
2200-0000
NIPPLE KIT
2400-2103
ELBOWS
2000-3002
BIBB CAP
12564
1000-5001
BONNET
WASHER
1000-0001
RETAINER DISK
ASSEMBLY
2922-5000
HANDLE
GASKET
1000-5005
O-RING
2909-3400
LIFT PIN GUIDE
2000-2301
LEVER HANDLE
2000-8000
RED BUTTON
2000-8001
BLUE BUTTON
2901-0000
ADD-ON CONTROL
VALVE LESS SPOUT
15621
SPOUT NUT
2002
SNAP RING
1600-5000
SPOUT
O-RINGS
10456
LUBE
SWIVEL SPOUT
RETRO-FIT KIT
AND
19119
2000-7500
SCREW
REV. A
fisher manufacturing company
8” Adjustable Wall Mount Utility Spray
Product Installation Guide
Since 1936, Fisher Manufacturing Company has
manufactured heavy-duty, high quality plumbing
products and hardware specialties for the food service
industry. For three generations, the Fisher family has
adhered to a strict dedication of and overall value.
When you install Fisher products… you install the best.
Our hardware is manufactured with the standardization
of internal mechanisms. All chrome plating is triple
plated copper, nickel and chrome for durability. Every
piece of equipment we make is rigorously tested in
both our modern in-house testing center and in actual
fi eld situations under extreme conditions. Every detail
is thoroughly checked. Before we make our products
available to you, they pass each and every test. You get
proven performance. Guaranteed.
Limited One Year Warranty
Fisher Manufacturing Company warrants its products
and parts thereof (except as noted below) against
defects in materials or workmanship for a period of
one year after the date of original purchase. During
this period Fisher Manufacturing Company will
replace a defective product or part without charge to
you, provided that the entire product is delivered to
Fisher Manufacturing Company. All transportation and
insurance charges for shipping the product to and from
Fisher Manufacturing Company must be borne by you.
Charges for transportation and insurance may, at the
option of Fisher Manufacturing Company, be refunded
depending upon our investigation of the warranty claim.
This warranty does not cover external fi nish (except at
date of original purchase) or labor costs not specifi cally
authorized by Fisher Manufacturing Company.
A full and complete copy of our One Year limited
warranty is available upon request.
WARNING:
Proposition 65 requires that we provide you with the
following notice: “This product Contains A Chemical
Known To The State Of California To Cause Birth
Defects Or Other Reproductive Harm.”
KEEP THIS MANUAL FOR FUTURE REFERENCE
fisher manufacturing company - toll free: 800-421-6162 fax: 800-832-8238
#2260 - Utility Spray: 8” Adjustable Wall Mount Control
Valve with Vacuum Breaker and Wall Hook
#2270 - Utility Spray: 8” Adjustable Wall Mount Control
Valve with Swivel Hose Adapter and Wall Hook
ANSI/A112.18.1M, ANSI/NSF 61.9
www.fi sher-mfg.com
Installation Instructions for Utility Spray
PREVENTER
WATTSN9
BACK-FLOW
Installation Instructions Continued
BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION
REGARDING BACKFLOW PREVENTION
Installation Notes:
• Be sure to shut off water supply before beginning.
• Use pipe thread sealant such as PST on all threaded joints.
• Check the packaging for missing items BEFORE beginning installation. If items are missing, contact your supplier.
Tools Required for Installation
• Medium Sized Crescent Wrench
• Pipe Thread Sealant
• Phillips Screwdriver
Installation Instructions
1. Insert the gasket into the groove on the eccentric.
Making sure gasket is in place, loosely mount the
eccentric and fl ange onto the control valve body.
2. If no add-on faucet will be installed, proceed to step
3. If installing an add-on faucet, mount the small
riser to the control valve body using thread sealant.
Thread the add-on faucet to the other end of the
small riser, again using thread sealant.
3. Mount control valve body to either a wall with male
supply nipples, or a backsplash with nipples (not
included). Be sure to use pipe thread sealant on
the supply nipple threads. Adjust the eccentrics as
needed in order to mount the control valve level.
Once level, tighten the eccentrics.
4. Mount either the swivel hose adapter with vacuum
breaker (2932) or swivel hose adapter without
vacuum breaker (2931) to control valve body. Use
lube on the o-rings on the swivel hose adapter and
be sure white snap ring is in place. Tighten nut until
swivel hose adapter is secure.
5. If installing a backfl ow preventer, do so by applying
thread sealant and inserting into the swivel hose
adapter, tightening until secure. Be sure that arrows
on backfl ow preventer are pointing in direction of
fl ow. Using pipe thread sealant, insert the stainless
steel hose into either the backfl ow preventer or the
swivel hose adapter and tighten nut until secure.
6. Fit one of the handle gaskets inside the outlet of the
insulated handle and mount the utility spray valve
onto it. Fit the other handle gasket inside the inlet of
the insulated handle and mount the handle onto the
stainless steel hose. Be sure that gaskets are used
on both sides of the insulated handle.
7. If installing a brush, do so by pressing brush into
the bumper of the spray valve until secure.
PST
Step 1
Step 2
Step 3
Gasket
Eccentric
Thread Sealant
Goes Here
1/2” NPT Supply
Nipples (not included)
7 3/4” - 8 1/4”
[196.9 - 209.6mm]
Flange
8. To install the wall bracket, determine a good
location and hold fi rmly against the wall. Using a
screwdriver, insert the three screws through the
holes in the wall hook and screw into the wall.
9. To install swing spout to add-on faucet, apply lube
to the o-rings on the swing spout. Make sure the
white snap ring is in place before mounting the
swing spout. Mount the swing spout and tighten the
swing spout nut onto the add-on faucet spout outlet
10. Turn on water supply and check for leaks.
Step 5 Step 6
Thread Sealant
Goes Here
Step 8
Step 9 Step 10
Swing Spout
Apply O-Ring
Lube Here
Step 4
Handle Gasket
2932
Swivel Hose
Adapter with
Vacuum Breaker
Apply O-Ring
Lube Here
Step 7
3
/4” - 8 1/4”
Ø7/8”
7
[196.9 - 209.6mm]
Loading...