Fisher 19526 Parts Manual
Replacement Parts for Backsplash Faucets
fisher manufacturing company
2000-5003
SEAT WASHER
ANGLE STOP
W/ CROSS
HANDLET
ANGLE STOP
WITH KEY
1790-1
1792
T
O
H
H
O
T
3600
CONTROL VALVE
2000-7500
SCREW
2000-8000
RED BUTTON
2000-8001
BLUE BUTTON
2000-2301
LEVER HANDLE
2000-3002
BIBB CAP
DUCK GASKET
2000-5000
WASHER
3000-0010
LH SWIVEL STEM
3000-0011
RH SWIVEL STEM
1000-7502
SCREW
L
D
O
C
C
O
D
L
AND
10464
OR
10456
LUBE
3000-0000
RH SWIVEL STEM
REPAIR KIT
OR
3000-0001
LH SWIVEL STEM
REPAIR KIT
10014 (24”)
10022 (36”)
SUPPLY LINE
1/2” F X 1/2” F
10049 (24”)
10006 (36”)
SUPPLY LINE
1/2” M X 1/2” F
3967
16” SWING SPOUT
3964
14” SWING SPOUT
3963
12” SWING SPOUT
3962
10” SWING SPOUT
3961
8” SWING SPOUT
3960
6” SWING SPOUT
3000-0003
DOUBLE JOINT
SPOUT 7 1/4”
4000-0002
DOUBLE JOINT
SPOUT 13”
12564
2.2 GPM
AERATOR
OR
15621
SPOUT NUT
2002
SNAP RING
1600-5000
SPOUT
O-RINGS
10456
LUBE
19119
SWIVEL SPOUT
RETRO-FIT KIT
2400-2103
ELBOWS
1000-8002
SLIP JOINT KIT
4” C/C Backsplash Faucet
Product Installation Guide
Since 1936, Fisher Manufacturing Company has
manufactured heavy-duty, high quality plumbing
products and hardware specialties for the food service
industry. For three generations, the Fisher family has
adhered to a strict dedication of and overall value.
When you install Fisher products… you install the best.
Our hardware is manufactured with the standardization
of internal mechanisms. All chrome plating is triple
plated copper, nickel and chrome for durability. Every
piece of equipment we make is rigorously tested in
both our modern in-house testing center and in actual
fi eld situations under extreme conditions. Every detail
is thoroughly checked. Before we make our products
available to you, they pass each and every test. You get
proven performance. Guaranteed.
Limited One Year Warranty
Fisher Manufacturing Company warrants its products
and parts thereof (except as noted below) against
defects in materials or workmanship for a period of
one year after the date of original purchase. During
this period Fisher Manufacturing Company will
replace a defective product or part without charge to
you, provided that the entire product is delivered to
Fisher Manufacturing Company. All transportation and
insurance charges for shipping the product to and from
Fisher Manufacturing Company must be borne by you.
Charges for transportation and insurance may, at the
option of Fisher Manufacturing Company, be refunded
depending upon our investigation of the warranty claim.
This warranty does not cover external fi nish (except at
date of original purchase) or labor costs not specifi cally
authorized by Fisher Manufacturing Company.
A full and complete copy of our One Year limited
warranty is available upon request.
WARNING:
Proposition 65 requires that we provide you with the
following notice: “This product Contains A Chemical
Known To The State Of California To Cause Birth
Defects Or Other Reproductive Harm.”
#19461 - 4” c/c Backsplash Faucet, 6” Swing Spout with
Elbows
#19488 - 4” c/c Backsplash Faucet, 8” Swing Spout with
Elbows
#19496 - 4” c/c Backsplash Faucet, 10” Swing Spout with
Elbows
#19518 - 4” c/c Backsplash Faucet, 12” Swing Spout with
Elbows
#19526 - 4” c/c Backsplash Faucet, 14” Swing Spout with
Elbows
#19534 - 4” c/c Backsplash Faucet, 16” Swing Spout with
Elbows
PART NO. 73712
MANFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
(800)421-6162, FAX: (800)832-8238
www.fisher-mfg.com
REV. A
KEEP THIS MANUAL FOR FUTURE REFERENCE
ANSI/A112.18.1M, ANSI/NSF 61.9
fisher manufacturing company - toll free: 800-421-6162 fax: 800-832-8238
www.fi sher-mfg.com
Installation Instructions for Backsplash Faucets
O
T
O
H
H
T
C
D
O
L
O
L
D
C
O
T
O
H
H
T
C
D
O
L
O
L
D
C
O
T
O
H
H
T
C
D
O
L
O
L
D
C
BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION
REGARDING BACKFLOW PREVENTION
Installation Instructions Continued
Installation Notes:
• Be sure to shut off water supply before beginning.
• Use pipe thread sealant such as PST on all threaded joints.
• Check the packaging for missing items BEFORE beginning installation. If items are missing, contact your supplier.
Tools Required for Installation
• Medium Sized Crescent Wrench
• Pipe Thread Sealant
PST
Package Contents
The box should contain the following:
Qty: 1
L
D
O
C
C
O
D
L
Swing Spout
Length determined by model
Each spout includes one 2002 snap ring
Qty: 1
and two 1600-5000 o-rings
2400-2103
Elbows
Qty: 2
1000-8002
Slip Joint Kit
Qty: 2
10456
Lube
T
O
H
H
O
T
Control Valve
Installation Instructions
1. Mount control valve body to the backsplash by inserting the nipples through the backsplash
and attaching slip joints. Tighten the slip joints until the control valve is secure. Be sure to use
pipe thread sealant on the nipple threads. Attach elbows or supply lines as needed.
2. If installing a double joint spout, apply lube to the o-rings on the spout. Mount the double joint
spout and tighten the nut onto the faucet spout outlet.
3. Apply lube to the o-rings on the swing spout. Make sure the white snap ring is in place before
mounting the swing spout. Mount the swing spout and tighten the swing spout nut onto the
faucet spout outlet.
4. Turn on water supply and check for leaks.
Step 2
Step 3
Double Joint Spout
Apply O-Ring
Lube Here
T
O
H
H
O
T
T
O
H
H
O
T
L
D
O
C
C
O
D
L
Swing Spout
Apply O-Ring
Lube Here
L
D
O
C
C
O
D
L
Step 1
Step 4
Slip Joints
4”
Ø7/8”
[101.6mm]
1/2” Elbows
T
O
H
H
O
T
L
D
O
C
C
O
D
L
Loading...