Firstech FT-DC2-S Install Manual

U.S. Patent No. 8,856,780
20171006
REVISION DATE
FT-RSA-NI8-[FT-DC2-S]
FIRMWARE
FT-DC2-S
HARDWARE
ADS-USB (OPTIONAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL)
ACCESSORIES
DOCUMENT NUMBER
2017 NISSAN QASHQAI PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2017
INSTALL GUIDE
NOTICE
The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.
T003_H
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 2 OF 9
U.S. Patent No. 8,856,780 2017 Nissan Qashqai PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2017 FT-RSA-NI8-[FT-DC2-S]-EN
20171006
!
1
2
2
2
2
2
5
5
1212 1111 1010 99 88 44 33 22 1177 66 5
2424 2323 2222 2121 2020 1616 1515 1414 131319 1818 1717
12 1212223234245
2525626727828929103011313213331434
1535163617371838193920
40
12 12122232342452562672782892910301111
313213331434153516361737183819392040
1234
8 7
6 5
1
2
3
T003_H
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
OEM REMOTE REMAINS FUNCTIONAL DURING REMOTE START SEQUENCE
T-HARNESS / WIRING DIAGRAM - 1 OF 1
1: BLACK CONNECTOR
1: GREEN
2: BLACK CONNECTOR
3: GRAY CONNECTOR
M5
M4
M2
M3
0404
0303
0404
OBDII (A)
BCM (B)
POWER LIFTGATE SWITCH (C)
06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT
06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT
08
0101
0202
0303
0505
07 BROWN•BLACK DOT - SIREN (+) OUTPUT07 BROWN•BLACK DOT - SIREN (+) OUTPUT
BROWN/BLACK•BLACK DOT
BROWN/BLACK•BLACK DOT
09 PURPLE/BLACK•BLACK DOT - POC 2 (-) OUTPUT
09 PURPLE/BLACK•BLACK DOT - POC 2 (-) OUTPUT
1111
1212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT
02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT
03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT
04 GREEN•SILVER DOT04 GREEN•SILVER DOT
05 EMPTY05 EMPTY
06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT
09 EMPTY09 EMPTY
10 TAN•SILVER DOT10 TAN•SILVER DOT
0101
0202
0505
0606
0707
0808
0909
1010
1111
1212
1313
1414
1515
1616
1717
1818
1919
2020
0101
0202
0404
0505
0606
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
POWER LIFTGATE (-) LTGREEN - 06
HOOD SWITCH
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
4
4
4
WARNING: T-HARNESS VS5 AND VS6 CONNECTORS FIT MULTIPLE BCM CONNECTORS.
CONNECT TO GRAY CONNECTOR.
0303
10 WHITE/BLACK•BLACK DOT - POC 3 (-) OUTPUT10 WHITE/BLACK•BLACK DOT - POC 3 (-) OUTPUT
NOT REQUIRED FOR BASIC INSTALLATION. INSERT WIRE TERMINALS IN MS2 CONNECTOR FOR OPTIONAL OUTPUTS. REFER TO PRODUCT GUIDE FOR INFORMATION.
MS3
MS1
VS1
VS2
VS3 C3
VS4
VS8
VS7 C1
1: OBDII CONNECTOR 16 PIN
1: OBDII HARNESS
BLACK
WHITE
WHITE
WHITE
BLACK
BLACK
BLUE
BLUE
JS1
NC
NC
JS3 NI8-NI9
JS2 NI3
MS2
3
CUT THE BROWN/RED AND BROWN/YELLOW WIRES.
INSULATE THE OBDII SIDE OF THE CUT WIRES AND
CONNECT THE OTHER SIDE TO VEHICLE CANH AND CANL.
1: HARNESS
2: HARNESS
VS6
VS5 C2
3: HARNESS
12 12122232342452562672782892910
30
11
20
3132133314341535163617371838193940
4: GREEN
40
4
CANL (DATA) PINK - 40
CANH (DATA) BLUE - 20
BROWN/YELLOW
BROWN/RED
!
M3
M2
M5 M4
PAGE 3 OF 9
U.S. Patent No. 8,856,780 2017 Nissan Qashqai PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2017 FT-RSA-NI8-[FT-DC2-S]-EN
20171006
T003_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 4 OF 9
U.S. Patent No. 8,856,780 2017 Nissan Qashqai PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2017 FT-RSA-NI8-[FT-DC2-S]-EN
20171006
!
1
2
2
10 11 12 13 14 15 1616
1 2 3 4 5 6
4 7 8
9
1212 1111 1010 99 88 44 33 22 1177 66 5
2424 2323 2222 2121 2020 1616 1515 1414 1313
19 1818 1717
12 1212223234245256267278289
29103011313213331434
1535163617371838193920
40
12 1212223234245256267278
28
25
2728
929103011
11
313213331434153516361737183819392040
1234
8 7
6 5
1
2
3
4
T003_W
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
OEM REMOTE REMAINS FUNCTIONAL DURING REMOTE START SEQUENCE
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1: BLACK
1: GREEN
2: BLACK
3: GRAY
WHITE
M5
M4
M2
M3
04 EMPTY04 EMPTY
03 BROWN/RED - CANH 103 BROWN/RED - CANH 1 04 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
CANH (DATA) BLUE - 20
IGNITION (+) YELLOW - 08
PTS (-) RED - 09
LOCK (-) BROWN - 12
NEG. STARTER (-) BLUE - 19
UNLOCK (-) PINK - 13
CANL (DATA) PINK - 40
HAZARD LIGHT (-) WHITE/YELLOW - 11
NEG. IGNITION 3 (-) WHITE/PINK - 25
NEG. IGNITION 1 (-) WHITE/GREEN - 27
NEG. IGNITION 2 (-) WHITE/BLUE - 28
GROUND (-) BLACK - 04
12V (+) WHITE - 16
POWER LIFTGATE (-) LTGREEN - 06
OBDII (A)
BCM (B)
POWER LIFTGATE SWITCH (C)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 EMPTY08 EMPTY
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT 02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE•BLACK DOT - IGNITION (-) OUTPUT
03 RED/WHITE•BLACK DOT - IGNITION (-) OUTPUT
05 EMPTY05 EMPTY
07 BROWN•BLACK DOT07 BROWN•BLACK DOT
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT - TRUNK (-) OUTPUT11 BROWN/BLACK•BLACK DOT - TRUNK (-) OUTPUT 12 WHITE•BLACK DOT - PARKING LIGHT (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHT (-) OUTPUT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT
02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT
03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT
04 GREEN•SILVER DOT04 GREEN•SILVER DOT
05 EMPTY05 EMPTY
06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT
09 EMPTY09 EMPTY
10 TAN•SILVER DOT10 TAN•SILVER DOT
01 EMPTY01 EMPTY
02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED
06 BLUE/YELLOW06 BLUE/YELLOW
07 EMPTY07 EMPTY
08 ORANGE08 ORANGE
09 YELLOW09 YELLOW
10 EMPTY10 EMPTY
11 GRAY/RED11 GRAY/RED
12 GRAY/YELLOW12 GRAY/YELLOW
13 GREEN/RED13 GREEN/RED
14 ORANGE/WHITE14 ORANGE/WHITE
15 BROWN15 BROWN
16 ORANGE/BLACK - PTS (-) OUTPUT16 ORANGE/BLACK - PTS (-) OUTPUT 17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT
18 PURPLE18 PURPLE
19 RED - POWER 12V (+) INPUT19 RED - POWER 12V (+) INPUT 20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - GROUND (-)01 GRAY/BLACK•BLUE DOT - GROUND (-)
02 WHITE/BLACK•BLUE DOT02 WHITE/BLACK•BLUE DOT
04 WHITE/RED•BLUE DOT04 WHITE/RED•BLUE DOT
05 GRAY•BLUE DOT - STARTER (-) OUTPUT05 GRAY•BLUE DOT - STARTER (-) OUTPUT
06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
HORN (-)
HOOD SWITCH
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
4: GREEN
12 121222323424525626727828929103011
20
3132133314341535163617371838193940
40
!
M3
M2
M5 M4
PAGE 5 OF 9
U.S. Patent No. 8,856,780 2017 Nissan Qashqai PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2017 FT-RSA-NI8-[FT-DC2-S]-EN
20171006
01
ENGINE
START
STOP
STOP ACC ON START
ON
02
03
ENGINE
START
STOP
STOP ACC ON START
STOP
04
05
ENGINE
START
STOP
STOP ACC ON START
ON
06
07
ENGINE
START
STOP
STOP ACC ON START
STOP
08
09
10
11
ENGINE
START
STOP
STOP ACC ON START
ON
12
13
ENGINE START
STOP
STOP ACC ON START
START
14
15
16
17
18
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Set ignition to ON position.
Wait, LED 1 will turn solid RED, then solid GREEN for 1 second, then solid RED.
Set ignition to OFF position.
Wait, LED 1 will turn OFF.
Set ignition to ON position.
If LED 1 flashes GREEN rapidly, proceed with step 7. If LED 1 turns solid GREEN for 2 seconds, proceed with step 13.
Set ignition to OFF position.
WARNING: Disconnect power last. Disconnect module from vehicle.
Connect module to computer and proceed with extended programming.
Connect power first. Connect module to vehicle.
Set ignition to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 9
U.S. Patent No. 8,856,780 2017 Nissan Qashqai PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2017 FT-RSA-NI8-[FT-DC2-S]-EN
20171006
>>
01
02
03
04
05
06
>>
TAKEOVER PROCEDURE - 1 OF 1
All vehicle doors must be closed and locked prior to remote start sequence.
Time restriction. Complete steps 2 to 5 within 45 seconds.
Unlock driver door.
Open driver door and enter vehicle.
Close driver door.
Press and release BRAKE pedal.
Take over procedure completed.
Failure to follow procedure will result in vehicle engine shutdown.
PAGE 7 OF 9
U.S. Patent No. 8,856,780 2017 Nissan Qashqai PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2017 FT-RSA-NI8-[FT-DC2-S]-EN
20171006
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock? YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock? YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start? YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down? YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12
If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once
[1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the
wiring diagram, if applicable, and call technical support.
19 Exit vehicle. 20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 8 OF 9
U.S. Patent No. 8,856,780 2017 Nissan Qashqai PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2017 FT-RSA-NI8-[FT-DC2-S]-EN
20171006
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down? YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step. 9 Close hood.
10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal.
 
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if
applicable, and call technical support.
14 Exit vehicle. 15 Installation checklist completed.
PAGE 9 OF 9
U.S. Patent No. 8,856,780 2017 Nissan Qashqai PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2017 FT-RSA-NI8-[FT-DC2-S]-EN
20171006
U.S. Patent No. 8,856,780
20171006
REVISION DATE
FT-RSA-NI8-[FT-DC2-S]
FIRMWARE
FT-DC2-S
HARDWARE
ADS-USB (OPTIONAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL)
ACCESSORIES
DOCUMENT NUMBER
2017 NISSAN ROGUE SPORT PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2017
INSTALL GUIDE
NOTICE
The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.
T003_H
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 2 OF 9
U.S. Patent No. 8,856,780 2017 Nissan Rogue Sport PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2017 FT-RSA-NI8-[FT-DC2-S]-EN
20171006
Loading...
+ 25 hidden pages