User Guide
for countertop and mobile terminals
First Data Merchant Solutions
EFTPOS
2 Contents
Get to know your terminal
05
Introduction 06
Terminal location and PIN privacy 06
Terminal ownership 07
Settlement 07
Your terminal layout 08
First Data countertop EFTPOS terminal 08
First Data mobile EFTPOS terminal 09
Transaction processing options 10
Installing the privacy shield 11
Loading receipt paper 12
To switch the terminal on and off 13
Communications setup 14
First Data countertop EFTPOS terminal 14
First Data mobile EFTPOS terminal 16
What are you
looking for?
3
Get to know your terminal
Contents 3
Operating your EFTPOS terminal
23
Purchase transaction 22
Purchase transaction with a credit card 26
Cash out transaction 30
Cash out transaction with a purchase 30
Cash out-only transaction 30
Refund transaction 34
Reprint last receipt 38
Cancel transaction 39
Other transaction types 40
Pre-authorisation 40
Processing and pre-authorisation transaction 41
Processing and completion transaction from a pre-authorisation 44
Mail order/telephone order (MOTO) 47
Electronic commerce interface (ECI) 50
Void 53
Administration functions 56
Settlements 56
Tip addition 58
Reports 61
Shift report 61
Settlement report 61
Daily report 62
Transaction report 62
Other terminal functionality 62
Training mode 62
Surcharging 64
Customer receipt marketing message 65
Offline transaction processing 66
Multi merchant capability 67
Hot keys 68
User management 69
Shift change 70
Where to get help 72
4
Get to know your terminal
01
5
Get to know your terminal
Get to know
your terminal
6
Get to know your terminal
Introduction
Terminal location and
PIN privacy
Your First Data Merchant Solutions EFTPOS terminal allows you to accept credit, debit and charge card
transactions electronically as a means of payment.
Customers can access their cheque, savings or credit accounts for purchases and refunds. Customers can
also request cash out from cheque and savings accounts.
The physical location of an EFTPOS terminal is
important in protecting a customer’s PIN privacy.
When your new terminal is installed or relocated
within the premises, you must take care to ensure:
> the EFTPOS terminal is in a position that allows
the customer to enter their PIN so it cannot be
observed by employees or other customers
> the EFTPOS PIN pad has an adequate length of
terminal connection cord to allow customers to
enter their PIN privately
> if in a fixed position, the EFTPOS PIN pad has
not been placed at an angle or height that
prevents customers from shielding their PIN
entry
> the placement of mirrors and other reflective
materials do not allow the customer’s PIN entry
to be observed through reflection
> security cameras can’t make a visual record of a
customer’s PIN entry.
You should communicate these guidelines to any
staff members that process EFTPOS transactions
using the First Data Merchant Solutions terminal.
It is also important to remind staff members that
customers should never be asked to disclose a PIN.
7
Get to know your terminal
Terminal ownership
Settlement
All physical equipment provided to the merchant by First Data Merchant Solutions remains the property
of First Data Merchant Solutions. This can include but is not limited to EFTPOS terminals, PIN pads, power
packs, phone line cables and any additional hardware provided at the time of installation.
You can initiate settlement manually via the
terminal menu any time before 1730 local time.
You can also configure your EFTPOS terminal to
automatically settle any time between 0001 and
1800 local time.
If you want to change your settlement terminal cut
off time to allow for longer trading hours, please
visit the merchant support page to download a
form and email your request.
If you do not complete settlement using one of
these methods, your EFTPOS terminal will prompt
you to manually settle when processing the first
transaction after 1800 local time.
You can perform multiple settlements a day at
any time, but the first settlement of the day (after
0301 and before 1730) will be the only settlement
processed that day. You can obtain totals for
transactions processed after the first settlement
through the reports function on the terminal menu.
8 Get to know your terminal
Your terminal layout
First Data Merchant Solutions countertop
EFTPOS terminal
Receipt printer
Integrated contactless card
reader lights.
(Contactless reader is
embedded behind screen)
Colour touch screen terminal display
Magnetic stripe card reader
Alpha/numeric keys
Power on/off and cancel key
Back key
Enter key
Chip card reader
Receipt printer
Integrated contactless card
reader lights.
(Contactless reader is
embedded behind screen)
Colour touch screen terminal display
Magnetic stripe card reader
Alpha/numeric keys
Power on/off and cancel key
Back key
Enter key
Chip card reader
9 Get to know your terminal
Your terminal layout
First Data Merchant Solutions mobile
EFTPOS terminal
10
Get to know your terminal
Transaction processing options
The First Data Merchant Solutions EFTPOS terminal
has a chip card reader, a magnetic stripe reader
and an integrated contactless reader for processing
transactions.
All chip cards must be inserted into the chip card
reader as shown below.
> Insert the credit card into the card reader with the
gold contact pad facing upward, as shown below.
> Leave the chip card in the reader until the
transaction is completed and the terminal
prompts you to remove it.
> The terminal screen prompts will guide you
through the transaction process.
If the card is capable of performing a contactless
transaction, place the card over the contactless
reader, as shown below.
If the card does not have a chip or contactless
capability, you can process transactions by swiping
the magnetic stripe through the terminal.
Smart card reader — The integrated circuit card (ICC)
reader is located at the bottom end. Please make sure that
the gold ICC contact pad is facing upward when inserting
the card into the slot.
Magnetic card reader — The card reader slot is on the
right side of the terminal. With the magnetic stripe facing
[inwards], slide the card in either direction through the slot
without stopping. If the card swipe fails, check the position
of the magnetic stripe and slide the card again.
Contactless card reader —The contactless card reader
antenna is embedded behind the display and PIN pad. The
reader’s lights will show blue when the terminal is powered
on to indicate the reader is working normally. To process a
contactless payment, place the contactless card near the
card reader antenna during a transaction.
11
Get to know your terminal
Installing the privacy shield
You can choose to add a privacy shield to the terminal to
provide customers with additional security when entering
their PIN.
Remove the adhesive tab around the privacy shield.
Carefully place the privacy shield’s adhesive side around
the keypad.
12
Get to know your terminal
Loading receipt paper
01 — Open the printer cover by gently pulling the printer
cover’s latch, then lift the cover away from the printer.
02 — Load a roll of thermal paper into the printer.
03 — Ensure the roll will feed out of the terminal so that
the print side of the paper faces the operator.
04 — Close the cover by pressing down evenly on both side
tabs, or by pressing on the centre of the printer cover.
05 — Use the serrated bar to tear off any excess paper.
IMPORTANT
Always store thermal paper for your terminal in a dry, dark area.
Handle thermal paper carefully. Impact, friction, temperature, humidity and oils can affect the
colour and storage characteristics of the paper.
Never load a roll of paper that has folds, wrinkles, tears or holes at the edges of the print area.
Please call First Data Merchant Solutions on 1300 664 660 for all stationery orders.
13
Get to know your terminal
Switching the terminal on and off
To switch the terminal on:
> Connect the power supply cable to the power
pack and plug it into the terminal.
> Connect the telephone cable or Ethernet cable
and switch the terminal’s power on at the wall.
> Hold down the red X key until the screen
is formatting
> When powered on, your terminal will display the
application main screen before returning to the
idle state.
Do not disconnect your terminal’s power supply
or communication line unless instructed to do so
by the Help Desk. The terminal is now ready for
operation.
To switch the terminal off, hold down the red X key
until you are prompted with the power off option
on the screen.
14
Get to know your terminal
Communications setup
To connect the terminal to your
broadband internet connection:
> Ensure that Ethernet cabling is
available where the terminal is going
to be installed.
> Plug an Ethernet cable into the
Ethernet port on the back of the
terminal and connect the cable’s other
end to the router.
> Once the Ethernet cable connects
the First Data Merchant Solutions
countertop EFTPOS terminal with
your router, the lights on the back of
the terminal next to the Ethernet port
should flash to indicate a connection.
> If the lights fail to turn on, there is
no connection between the First
Data Merchant Solutions countertop
EFTPOS terminal and your router.
Please check your cable and router to
restore connectivity.
First Data countertop EFTPOS terminal
IP/Broadband
Please contact the helpdesk on 1800 243 444
to activate your First Data Merchant Solutions
countertop EFTPOS terminal for transactions over
a broadband connection.
To use the First Data Merchant Solutions
countertop EFTPOS terminals over a broadband
connection, you will need to have Internet access
and a router that has at least one spare Ethernet
port for each terminal you use.
Your router will need to have dynamic host
configuration protocol (DHCP) turned on. If your
router does not support DHCP, please contact
the helpdesk on 1800 243 444 to configure your
terminal for use with a static IP address. If your
connection has a firewall in place, you will need
to open ports 4108 and 443.
The First Data Merchant Solutions EFTPOS terminal is capable of processing transactions through a
broadband Internet connection as well as a standard phone line.
15
Get to know your terminal
Dial-up
Your countertop EFTPOS terminal features a
phone cable input that allows you to connect
your terminal using a regular dial-up phone line.
To process transactions using a standard phone
line, simply connect from the communication port
on your
First Data Merchant Solutions EFTPOS termina
directly to a telephone wall jack.
If the broadband connection fails and the terminal
is configured for a dial-up connection, it will
automatically switch to dial-up mode.
Below is an example of a possible network configuration that the EFTPOS terminal can use to
process transactions over IP/broadband Internet.
16
Get to know your terminal
First Data mobile EFTPOS terminal
Installing the SIM card
The mobile EFTPOS terminal comes with a pre-installed SIM card, so you should not need to install a SIM. If
you are instructed to remove the SIM by the helpdesk, please use the following reinstallation steps.
Turn your mobile EFTPOS terminal off before replacing the
SIM card.
There are four SIM slots on the left side of the device.
Insert the SIM card in the appropriate slot.
Make sure the SIM card is inserted in the correct
direction, as shown.
17
Get to know your terminal
WiFi Settings
Connecting to WiFi
The First Data Merchant Solutions mobile EFTPOS terminal comes with the option of WiFi capability.
To connect to your local WiFi network, the following steps should be performed:
Step 01
Step 03
Step 02
Step 04
Select Admin
Select WiFi
Select Next
Expand the first tree node
Instructions continue on next page >
18
Get to know your terminal
Step 05
Step 07
Step 09
Step 06
Step 08
Expand the WiFi node
To edit the current value, select the text field at the
bottom of the screen
Press the main Ok button to save all the changes
made, or press cancel to retain the original values.
Select the required field node
Use the virtual keyboard to enter the required
value and press the OK button next to the Space Bar
buttonto accept the current change
Once you have made the necessary
changes, restart the device. It may
take up to two minutes for the WiFi
connection to be established once
power is restored.
19
Get to know your terminal
Below is a table detailing the various options available in the terminal’s WiFi setup.
Note: To connect to a WiFi network, you usually only need to fill out the ‘SSID’ and ‘Key’ values.
SSID Name of wireless connection
AdHoc False (default)
True
WiFiMode 1 – MD5
2 – PEAP
3 – TLS (default)
Encryption 0 – Disable
1 – WEP
2 – TKIP
3 – AES (default)
Authentication 0 – Open
1 – Shared
2 – WPA_PSK
3 – WPA
4 – WPA_PSK (default)
5 – WPA2
Key Authentication key
DN WPA domain name (optional)
UN WPA user name (optional)
CAKEY WPA CA key (optional)
PWD WPA password over DES encryption (optional)
20
Operating your EFTPOS terminal
02
21
Operating your EFTPOS terminal
Operating
your EFTPOS
terminal
22
Operating your EFTPOS terminal
Purchase transaction
This section describes how to complete a purchase transaction.
Note: Your terminal can be configured with three frequently used functions or ‘hot keys’.
Refer to page 70 for further details.
TIP
You can perform a purchase transaction in three simple steps.
Simply start keying in the transaction amount from either the idle screen (the main screen) or when the
terminal is in ‘screen saver’ mode and the terminal will recognise that you are undertaking a basic purchase
transaction.
This means if the purchase is performed as a contactless transaction, you can perform a transaction by
following the steps:
Step 1 – Type the purchase amount Step 2 – Present/tap the card Step 3 – Print the customer’s receipt
Step 01
Step 03
Step 02
Step 04
Key in the purchase amount and press the green
ENTER key on the keypad.
Alternatively, if ‘Purchase’ is not a configured hot
key, select ‘Transaction’, then select ‘Purchase’
from the transaction list.
Key in the cash out amount if required.
Select ‘Purchase’ from the main screen.
If it is configured as a hot key. (Refer to page 70
for details)
$0.00
$0.00
23
Operating your EFTPOS terminal
Step 05 Step 06
Step 07
Step 08
Key in the tip amount if required.
Insert, tap or swipe the card.
Note: the value for a contactless transaction
is $100 or greater, the terminal will prompt the
customer to enter a PIN or insert their card.
Select the account type.
Confirm the transaction amount.
$0.00
Purchase: $$.$$
Total: $$.$$
Instructions continue on next page >
24
Operating your EFTPOS terminal
Step 11
If the customer requires a copy of the receipt,
press the green ‘thumbs up’ button.
If the customer does not require a copy of the
receipt, press the red ‘thumbs down’ button.
Customer copy?
Step 09
Ask the customer if they would prefer to enter
their PIN or sign the receipt. Press ‘PIN’ or
‘Signature’ accordingly.
PIN or Sign?
Step 10
Step 12
This screen indicates the terminal is attempting
to process the transaction. The screen will
update to reflect the status, eg ‘APPROVED’.
If the customer used a chip card to process the
transaction, you can now remove the chip card.
EFTPOS in progress.
Please wait
Remove card
IMPORTANT
Please ensure that you check the transaction is approved before completing the sale. Hand the
customer their copy of the transaction record, their card and any cash out requested. If a transaction
is declined, tell the customer the reason, advise them to contact their bank if required and seek an
alternative form of payment.
25
Operating your EFTPOS terminal
Note: Graphic will only print on the customer copy of the receipt.
MERCHANT ID 4229851 2345678
TERMINAL ID
12345678
USER
01
INV NO
000012
STAN
000034
ACCOUNT TYPE SAVINGS
……..4221(s)
10/15
PURCHASE
$80.00
TOTAL $80.00
AUTH ID
00321
RRN 1234560 00034
APPROVED 00
XXXX Merchant
123 Sydney Street
North Sydney NSW 2060
Merchant Copy
28 OCT 2015 16:00:22
Example of a purchase transaction record
First Data Merchant Solutions
26
Operating your EFTPOS terminal
Purchase transaction
with a credit card
This section describes how to complete a transaction using a credit card.
Step 01 Step 02
Alternatively, if ‘Purchase’ is not a configured hot
key, select ‘Transaction’, then select ‘Purchase’
from the transaction list.
Select ‘Purchase’ from the main screen
if it is configured as a hot key.
(Refer to page 70 for details.)
Step 03
Key in the purchase amount and press the green
ENTER key on the keypad.
$0.00
Step 04
Key in the tip amount if required.
$0.00
27
Operating your EFTPOS terminal
Step 05 Step 06
Step 07
Insert, tap or swipe the card.
Note: the value for a contactless transaction
is $100 or greater, the terminal will prompt the
customer to enter a PIN or insert their card.
Select the ‘Credit’ account type.
Confirm the transaction amount.
Purchase: $$.$$
Total: $$.$$
Step 08
Ask the customer if they would prefer to enter
their PIN or sign the receipt. Press ‘PIN’ or
‘Signature’ accordingly.
PIN or Sign?
Instructions continue on next page >
28
Operating your EFTPOS terminal
Step 10
If the customer requires a copy of the receipt,
press the green ‘thumbs up’ button.
If the customer does not require a copy of the
receipt, press the red ‘thumbs down’ button.
Customer copy?
Step 09
Step 11
This screen indicates the terminal is attempting
to process the transaction.
If the customer used a chip card to process the
transaction, you can now remove the chip card.
EFTPOS in progress.
Please wait
Remove card
29
Operating your EFTPOS terminal
Note: Graphic will only print on the customer copy of the receipt.
MERCHANT ID 4229851 2345678
TERMINAL ID
12345678
USER
01
INV NO
000012
STAN
000034
ACCOUNT TYPE SAVINGS
VISA
……..4221(s)
10/15
PURCHASE
$35.00
SURCHARGE $3.50
SURCHARGE GST
$0.35
SUB-TOTAL AUD $38.85
TIP
TOTAL
First Data Merchant Solutions
XXXX Merchant
123 Sydney Street
North Sydney NSW 2060
Merchant Copy
28 OCT 2015 16:00:22
SIGNATURE
Example of a credit card record
AUTH ID
00321
RRN 1234560 00034
APPROVED 08
30
Operating your EFTPOS terminal
‘Cash out’ transaction
Customers may choose to get cash out by using your terminal to debit their cheque or savings account
with or without making a purchase. Cash out is not allowed on a credit card account.
As the owner of the business, you may choose whether or not to provide this additional facility to
customers.
Cash out transaction with a purchase
To process a cash out transaction with a purchase, simply follow the steps outlined on page 24 of this
guide under ‘Purchase transaction’.
Cash out–only transaction
You may process a ‘cash out’ transaction without a purchase by following these steps.
Step 01 Step 02
Alternatively, if ‘Cashout’ is not a configured hot
key, select ‘Transaction’, then select ‘Cashout’
from the transaction list.
Select ‘Cashout’ from the main screen
if it is configured as a hot key.
(Refer to page 70 for details.)
31
Operating your EFTPOS terminal
Step 03 Step 04
Step 05
Step 06
Key in the amount of cash required and press
the green ENTER key on the keypad.
Insert, tap or swipe the card.
Note: the value for a contactless transaction
is $100 or greater, the terminal will prompt the
customer to enter a PIN or insert their card.
Select either the ‘Cheque’ or ‘Savings’ account type.
Confirm the transaction amount.
$0.00
Cash: $$.$$
Total: $$.$$
Instructions continue on next page >
32
Operating your EFTPOS terminal
Step 09
If the customer requires a copy of the receipt,
press the green ‘thumbs up’ button.
If the customer does not require a copy of the
receipt, press the red ‘thumbs down’ button.
Customer copy?
Step 08
Step 07
Step 10
This screen indicates the terminal is attempting
to process the transaction.
Ask the customer to key in their PIN.
If the customer used a chip card to process the
transaction, you can now remove the chip card.
EFTPOS in progress.
Please wait
$NN.NN
Enter PIN
Remove card
IMPORTANT
Please ensure that you check the transaction is approved before completing the sale. Hand the customer
their copy of the transaction record, their card and any cash out requested. If the transaction is rejected,
the terminal will display an error message giving the reason. Communicate this reason with the customer.
33
Operating your EFTPOS terminal
Note: Graphic will only print on the customer copy of the receipt.
MERCHANT ID 4229851 2345678
TERMINAL ID
12345678
USER
01
INV NO
000012
STAN
000034
ACCOUNT TYPE SAVINGS
DEBIT
……..4221(s)
10/15
CASH-OUT $80.00
TOTAL AUD $80.00
XXXX Merchant
123 Sydney Street
North Sydney NSW 2060
Merchant Copy
28 OCT 2015 16:00:22
Example of a cash out transaction record
AUTH ID
00321
RRN 1234560 00034
APPROVED 00
First Data Merchant Solutions
34
Operating your EFTPOS terminal
Refund transaction
You can use the refund function when customers are returning goods and to reverse keying errors made by
operators.
IMPORTANT — If you are reversing an error, ensure the full amount of the transaction is refunded before
the purchase is re processed with the correct amount.
Step 01
Step 02
Alternatively, if ‘Refund’ is not a configured hot
key, select ‘Transaction’, then select ‘Refund’
from the transaction list.
Select ‘Refund’ from the main screen
if it is configured as a hot key.
(Refer to page 70 for details.)
Step 03
Step 04
Key in your user ID and press the green ENTER
key on the keypad if prompted.
Key in your password and press the green
ENTER key on the keypad if prompted.
Supervisor
NN
Password
XXXX
35
Operating your EFTPOS terminal
Step 05 Step 06
Step 07
Step 08
Key in the refund amount and press the
green ENTER key on the keypad.
Insert, tap or swipe the card.
Note: the value for a contactless transaction
is $100 or greater, the terminal will prompt the
customer to enter a PIN or insert their card.
Select the account type.
Confirm the transaction amount.
$0.00
Enter Refund
Amount
Refund: $$.$$
Total: $$.$$
Instructions continue on next page >
36
Operating your EFTPOS terminal
Step 09
Ask the customer if they would prefer to enter
their PIN or sign the receipt. Press ‘PIN’ or
‘Signature’ accordingly.
PIN or Sign?
Step 12
If the customer requires a copy of the receipt,
press the green ‘thumbs up’ button. If the
customer does not require a copy of the
receipt, press the red ‘thumbs down’ button.
Customer copy?
Step 11
Step 10
This screen indicates the terminal is attempting
to process the transaction.
Ask the customer to key in their PIN.
EFTPOS in progress.
Please wait
$NN.NN
Enter PIN
37
Operating your EFTPOS terminal
Step 13
If the customer used a chip card to process the
transaction, you can now remove the chip card.
Remove card
Note: Graphic will only print on the customer
copy of the receipt.
MERCHANT ID 4229851 2345678
TERMINAL ID
12345678
USER
01
INV NO
000012
STAN
000034
ACCOUNT TYPE Credit
VISA
……..4221(s)
10/15
REFUND $35.00
TOTAL $35.00
XXXX Merchant
123 Sydney Street
North Sydney NSW 2060
Merchant Copy
28 OCT 2015 16:00:22
Example of a refund
transaction record
AUTH ID
00321
RRN 1234560 00034
APPROVED 08
SIGNATURE
AUTH ID
1234560
RRN 1234560 00034
APPROVED 08
APPROVED WITH
SIGNATURE
First Data Merchant Solutions
38
Operating your EFTPOS terminal
Reprint last receipt
This section describes how to reprint the last receipt printed.
Step 01
Step 02
Step 03
Step 04
Select ‘Receipts’.
Select ‘Merchant’, ‘Customer’ or ‘Settlement’
to re-print the most recent receipt.
Select ‘Search’ to look for other receipts.
Select the required transaction
from the list or press the ‘Back’ button
to return to the main receipt screen.
Select ‘Admin’.
N. DD/MM INV No
39
Operating your EFTPOS terminal
Cancel transaction
Step 05
Press the green ‘thumbs up’ button to re-print
the receipt or press the ‘Back’ button to return
to the transaction list.
Inv # NNNNNN
Card
NNNN
Amount
$$.$$
Date dd/mm/yyyy
A transaction may be cancelled at any time before
the customer presses the green ENTER key or OK
for the PIN entry.
Pressing the red CANCEL key will cancel the
transaction and return the terminal to its idle state.
Once a customer has entered their PIN and
pressed ENTER, the transaction has been
completed and you will need to perform a refund
or void transaction if the customer needs to alter
their purchase.
40
Operating your EFTPOS terminal
Other transaction types
Pre-authorisation
The pre-authorisation function allows you to authorise and hold funds on a customer’s credit card for a
period of up to seven days. A pre-authorisation will not debit a customer’s account until a completion
transaction is processed at a later date. Each ‘transaction’ consists of two parts: the pre-authorisation and
the completion.
This facility is only available for use in certain industries, such as hotels or lodgings.
Part one: pre-authorisation
A pre-authorisation transaction requests
verification from a customer’s card-issuing bank for
the full value of the purchase. The customer’s bank
will issue a successful pre-authorisation request
with a 6-digit authorisation number.
IMPORTANT
The card issuer determines how long the
pre-authorisation value is ‘held’ against the
customer’s account. This period of time is typically
three to five days. After this, the authorisation
request expires and the business needs to issue
a new pre-authorisation request to begin the
transaction again.
Part two: completion
When processing the completion request, use the
following data to retrieve the pre-authorisation
transaction:
> the six-digit authorisation number
> the invoice number and amount
> the card number or date.
The amount of the completion request may not
exceed the pre-authorisation request by more than
15%. If it does, the transaction will be declined.
When a completion transaction is successful, its
value will be included in the end-of-day settlement
to your merchant account.
41
Operating your EFTPOS terminal
Processing a pre-authorisation transaction
Step 01 Step 02
Alternatively, if ‘Auth’ is not a configured hot
key, select ‘Transaction’, then select ‘Auth’ from
the transaction list.
Select ‘Auth’ from the main screen
if it is configured as a hot key.
(Refer to page 68 for details.)
Step 03
Key in the pre-authorisation amount and
press ENTER.
$0.00
Enter Amount
PREAUTH
Step 04
Insert, tap or swipe the card or manually
enter the card details
Instructions continue on next page >
42
Operating your EFTPOS terminal
Step 05
Select the green ‘thumbs up’ button if the
pre-authorisation amount is correct or the
red ‘thumbs down’ button if you wish to
cancel the transaction.
PreAuth $$.$$
Total: $$.$$
Step 06
Ask the customer if they would prefer to enter
their PIN or sign the receipt. Press ‘PIN’ or
‘Signature’ accordingly.
PIN or Sign?
Step 07
This screen indicates the terminal is attempting
to process the transaction.
EFTPOS in progress.
Please wait
Step 08
If the customer requires a copy of the receipt,
press the green ‘thumbs up’ button.
If the customer does not require a copy of the
receipt, press the red ‘thumbs down’ button.
Customer copy?
43
Operating your EFTPOS terminal
Note: Graphic will only print on the customer copy of the receipt.
MERCHANT ID 4229851 2345678
TERMINAL ID
12345678
USER
01
INV NO
000012
STAN
000034
ACCOUNT TYPE Credit
MASTERCARD
……..4221(s)
10/15
PRE-AUTH
$355.00
TOTAL AUD $355.00
XXXX Merchant
123 Sydney Street
North Sydney NSW 2060
Merchant Copy
28 OCT 2015 16:00:22
SIGNATURE
Example of a pre-authorisation transaction record
AUTH ID
00321
RRN 1234560 00034
APPROVED 08
APPROVED WITH
SIGNATURE
First Data Merchant Solutions
44
Operating your EFTPOS terminal
Processing a completion transaction
from a pre-authorisation
Step 01 Step 02
Alternatively, if ‘Checkout’ is not a configured
hot key, select ‘Transaction’, then select
‘Checkout’ from the transaction list.
Select ‘Checkout’ from the main screen
if it is configured as a hot key.
(Refer to page 68 for details.)
Step 03
Select an existing pre-authorised
transaction from the list.
N. DD/MM $$$.$$
Step 04
Press the green ‘thumbs up’ button if the
transaction details are correct.
Auth ID NNNNNN
Inv # NNNNNN
Card
NNNN
Amount
$$.$$
Date dd/mm/yyyy
45
Operating your EFTPOS terminal
Step 05 Step 06
Key in the Checkout amount and press ENTER. Key in the tip amount and press ENTER.
$0.00
Enter Amount
Checkout
$0.00
Step 07
Insert, tap or swipe the card.
Step 08
Step 09
Select the account type.
Select the green ‘thumbs up’ button if the
total amount is correct, the red ‘thumbs down’
button if you wish to cancel the transaction, or
‘Back’ if you wish to re enter the amount details.
Checkout: $$.$$
Tip: $$.$$
Total: $$.$$
Step 10
Ask the customer if they would prefer to enter
their PIN or sign the receipt. Press ‘PIN’ or
‘Signature’ accordingly.
PIN or Sign?
46
Operating your EFTPOS terminal
Step 11
This screen indicates the terminal is attempting
to process the transaction.
EFTPOS in progress.
Please wait
Step 12
If the customer requires a copy of the receipt,
press the green ‘thumbs up’ button.
If the customer does not require a copy of the
receipt, press the red ‘thumbs down’ button.
Customer copy?
Note: Graphic will only print on the customer
copy of the receipt.
MERCHANT ID 4229851 2345678
TERMINAL ID
12345678
USER
01
INV NO
000012
STAN
000034
ACCOUNT TYPE Credit
MASTERCARD
……..4221(s)
10/15
CHECKOUT
$355.00
TOTAL AUD $355.00
XXXX Merchant
123 Sydney Street
North Sydney NSW 2060
Merchant Copy
28 OCT 2015 16:00:22
SIGNATURE
Example of a processing a
transaction completion record
AUTH ID
00321
RRN 1234560 00034
APPROVED T08*
APPROVED WITH
SIGNATURE
First Data Merchant Solutions
47
Operating your EFTPOS terminal
Mail order/telephone order (MOTO)
Mail order and telephone order (MOTO) merchants are authorised to manually key credit card transactions.
The terminal will automatically default to ‘Credit’ as the account type whenever you manually enter card
numbers. Should you attempt to manually key a debit card number, the terminal will reject the transaction.
The MOTO process is similar to a normal purchase (or refund) that involves manually entering card details.
However, as the physical card and customer are not present at the point of sale, you should gather and
record as much customer information as possible before processing a MOTO transaction.
Step 01 Step 02
Alternatively, if ‘MOTO’ is not a configured hot
key, select ‘Transaction’, then select ‘MOTO’
from the transaction list.
Select ‘MOTO’ from the main screen
if it is configured as a hot key.
(Refer to page 68 for details.)
Instructions continue on next page >
48
Operating your EFTPOS terminal
Step 03
Step 05
Step 04
Step 06
Step 07
Select ‘Purchase’ or ‘Refund’
as the transaction type.
Key in the card number and press ENTER.
Key in the purchase or refund amount and
press ENTER.
Key in the expiry date on the card
and press ENTER.
Key in the CCV number on the back of the card
and press ENTER.
$0.00
Enter Amount
MOTO-Purchase
NNNNNNNN
Enter Expiry
(MMYY)
NNNN
Enter CCV
NNN
Step 08
Press green ‘thumbs up’ button to confirm the
amount or the red ‘thumbs down’ button to cancel it.
MOTO
Purchase: $$.$$
Total: $$.$$
49
Operating your EFTPOS terminal
Step 09
This screen indicates the terminal is attempting
to process the transaction.
EFTPOS in progress.
Please wait
Step 10
If the customer requires a copy of the receipt,
press the green ‘thumbs up’ button.
If the customer does not require a copy of the
receipt, press the red ‘thumbs down’ button.
Customer copy?
Note: Graphic will only print on the customer
copy of the receipt.
MERCHANT ID 4229851 2345678
TERMINAL ID
12345678
INV NO
000012
ACCOUNT TYPE Credit
MASTERCARD
……..4221(s)
10/15
MOTO PURCHASE
$99.00
TOTAL AUD $99.00
APPROVED 00
XXXX Merchant
123 Sydney Street
North Sydney NSW 2060
Merchant Copy
28 OCT 2015 16:00:22
Example of a MOTO
transaction record
First Data Merchant Solutions
50
Operating your EFTPOS terminal
Electronic commerce interface (ECI)
Step 01 Step 02
Alternatively, if ‘ECI’ is not a configured hot key,
select ‘Transaction’, then select ‘ECI’ from the
transaction list.
Select ‘ECI’ from the main screen if
it is configured as a hot key.
(Refer to page 70 for details.)
An electronic commerce interface (ECI) transaction occurs when a customer orders goods or services from
a merchant via a web-based interface or e-commerce platform and the customer and their card are not
present at the merchant outlet. The merchant must key the card number into the terminal to process the
purchase or refund transaction.
The process is similar to a normal purchase (or refund) with manual entry of card details. However, as the
physical card and customer are not present at the point of sale, you should gather and record as much
customer information as possible before processing an ECI transaction.
ENTER
$0.00
Enter Amount
ECI-Purchase
51
Operating your EFTPOS terminal
Step 05 Step 06
Step 07
Key in the card number and press ENTER.
Key in the expiry date on the card
and press ENTER.
Key in the CCV number on the back of the card
and press ENTER.
NNNNNNNN
Enter Expiry
(MMYY)
NNNN
Enter CCV
NNN
Step 08
Press green ‘thumbs up’ button to confirm the
amount or the red ‘thumbs down’ button to cancel it.
ECI
Purchase: $$.$$
Total: $$.$$
Step 09
This screen indicates the terminal is attempting
to process the transaction.
EFTPOS in progress.
Please wait
Step 10
If the customer requires a copy of the receipt,
press the green ‘thumbs up’ button. If the
customer does not require a copy of the
receipt, press the red ‘thumbs down’ button.
Customer copy?
52
Operating your EFTPOS terminal
Note: Graphic will only print on the customer copy of the receipt.
MERCHANT ID 4229851 2345678
TERMINAL ID
12345678
USER 01
INV NO
000012
STAN 004322
ACCOUNT TYPE Credit
VISA
……..4221(s)
10/15
ECI
PURCHASE $15.00
SURCHARGE $1.50
SURCHARGE GST $0.15
TOTAL AUD $16.65
XXXX Merchant
123 Sydney Street
North Sydney NSW 2060
Merchant Copy
28 OCT 2015 16:00:22
Example of a ECI transaction record
SIGNATURE
AUTH ID
00321
RRN 1234560 00034
APPROVED 08
APPROVED WITH
SIGNATURE
First Data Merchant Solutions
53
Operating your EFTPOS terminal
Void
There are some cases where either the merchant
or the customer makes a mistake during the
payment process and don’t realise until the
transaction has completed. In these instances, it
is too late to cancel or reverse the transaction and
the transaction must be voided instead.
The void function may need to be used if:
> the customer uses an incorrect card
> the merchant enters an incorrect amount
> the merchant accidentally adds a tip to an
incorrect transaction.
When this occurs, the merchant needs to void the
incorrect transaction and process a new one.
IMPORTANT — A void can only be performed on a
credit card transaction. A refund is the equivalent
process for debit transactions.
You can only void a transaction prior to performing
a settlement on your terminal (this includes forced
settlement).
There will be no record of the transaction and
its void on your customer’s bank account. This is
because the transaction is deleted before the
bank can complete it and no funds are removed
from your customer’s account.
The transaction and void will also not appear on
your terminal settlement summary for the same
reason. A record of the voided transaction will only
appear on your transaction list report.
If you have already settled your terminal, the
incorrect transaction must be refunded and
re-processed. For more information, refer to the
refund process on page 31 of this guide.
54
Operating your EFTPOS terminal
Step 03
Select the transaction you need to void.
N. DD/MM $$$.$$
Step 04
Press the green ‘thumbs up’ button if the
transaction details are correct.
Auth ID NNNNNN
Inv # NNNNNN
Card
NNNN
Amount
$$.$$
Date dd/mm/yyyy
Step 05
This screen indicates the terminal is attempting
to process the transaction.
EFTPOS in progress.
Please wait
Step 06
If requested, verify the customer’s signature.
Signature Required
Signature OK
Step 01 Step 02
Alternatively, if ‘Void’ is not a configured hot key,
select ‘Transaction’, then select
‘Void’ from the transaction list.
Select ‘Void’ from the main screen if it is configured
as a hot key. (Refer to page 72 for details.)
55
Operating your EFTPOS terminal
Step 07
If the customer requires a copy of the receipt,
press the green ‘thumbs up’ button. If the
customer does not require a copy of the
receipt, press the red ‘thumbs down’ button.
Customer copy?
Note: Graphic will only print on the customer
copy of the receipt.
MERCHANT ID 4229851 2345678
TERMINAL ID
12345678
USER 01
INV NO
000012
STAN 004322
ACCOUNT TYPE Credit
VISA
……..4221(s)
10/15
VOID
PURCHASE $55.00
TOTAL AUD $55.00
XXXX Merchant
123 Sydney Street
North Sydney NSW 2060
Merchant Copy
28 OCT 2015 16:00:22
Example of a void
transaction record
SIGNATURE
AUTH ID
00321
RRN 1234560 00034
APPROVED T08*
APPROVED WITH
SIGNATURE
First Data Merchant Solutions
56
Operating your EFTPOS terminal
Step 01 Step 02
Alternatively, if ‘Settlement’ is not a configured
hot key, select ‘Transaction’, then select
‘Settlement’ from the transaction list.
Select ‘Settlement’ from the main screen
if it is configured as a hot key.
(Refer to page 72 for details.)
The settlement function provides a “Settlement
Summary” receipt that summarises EFTPOS transactions
taken as at the current settlement date.
The net total amount on the receipt will be credited to
the nominated bank account you have provided to First
Data Merchant Solutions.
Important — We recommend that you perform a
settlement each day. If you do not, a settlement will
automatically be ‘forced’ by First Data Merchant
Solutions between 1730 and 1800 local time.
You can perform a settlement by following the steps
below.
Step 03
The terminal will display the settlement
processing status on the screen.
Administration functions
Settlements
<<status msg>>
57
Operating your EFTPOS terminal
Note: Graphic will only print on the customer
copy of the receipt.
MERCHANT ID 4229851 2345678
TERMINAL ID
12345678
BANK TOTALS
(AUD)
BATCH 0000002
SETL 02/02/2015
004322
SALES 28 $174.57
REFUNDS 51 $7.14
TOTAL 29
$167.43
CASH OUT 2
$8.32
ADJUSTS 2
$15.70
MERCHANT XXXX Merchant
MERCHANT ID
324234 3423423
TERMINAL ID 12345678
DEBIT
PUR 005
$37.25
CSH 002 $8.32
REF 001 ($7.14)
TOTAL
AUD $38.43
MASTERCARD
PUR 007 $47.88
TOTAL
AUD $38.43
VISA
PUR 008 $32.17
TOTAL
AUD $32.17
AMEX
PUR 002 $14.30
TOTAL
AUD $14.30
TOTAL DEBIT/
CREDIT
PUR 020 $117.30
CSH 002 $8.32
REF 001 ($7.14)
TOTAL
AUD $118.48
XXXX Merchant
123 Sydney Street
North Sydney NSW 2060
Merchant Copy
28 OCT 2015 16:00:22
to
29 OCT 2015 16:00:22
BANK TOTALS
Example of a settlement record
TERMINAL TOTALS
First Data Merchant Solutions
58
Operating your EFTPOS terminal
Step 01
Select ‘tip addition’ from the main screen if it is
configured as a hot key. (Refer to page 70 for details.)
If a customer needs to add a tip after completing the original transaction, your First Data Merchant Solutions
terminal allows you to add tips using the tip addition function.
A tip can only be added to a credit card purchase transaction and is limited to 25% of the transaction amount.
Tip addition
Step 02
Alternatively, if ‘Purchase’ is not a configured hot key,
select ‘Transaction’, then select ‘tip addition’ from
the transaction list.
Step 03
Select the transaction to which the
tip will be added.
N. DD/MM $$$.$$
Step 04
Press the green ‘thumbs up’ button if the transaction
details are correct.
Auth ID NNNNNN
Inv # NNNNNN
Card
NNNN
Amount
$$.$$
Date dd/mm/yyyy
59
Operating your EFTPOS terminal
Step 05 Step 06
Confirm purchase amount and press ENTER. Key in the tip amount and press ENTER.
$0.00
Verify Amount
$0.00
Enter Amount
Tip
Step 07
Press the green ‘thumbs up’ button to continue or
the red ‘thumbs down’ button to cancel the tip.
Purchase: $$.$$
Tip: $$.$$
Total: $$.$$
Step 08
This screen indicates the terminal is attempting
to process the transaction.
EFTPOS in progress.
Please wait
Step 09
If the customer requires a copy of the receipt, press
the green ‘thumbs up’ button. If the customer does
not require a copy of the receipt, press the red
‘thumbs down’ button.
Customer copy?
60
Operating your EFTPOS terminal
MERCHANT ID 4229851 2345678
TERMINAL ID
12345678
USER 01
INV NO 0000012
STAN
0000034
ACCOUNT TYPE CREDIT
VISA
........4221(S)
10/15
PURCHASE
$35.00
TIP
$2.00
SURCHARGE
$3.50
SURCHARGE GST
$0.35
TOTAL
AUD $40.85
AUTH ID
159876
RRN
123456780 00034
APPROVED
T00*
XXXX Merchant
123 Sydney Street
North Sydney NSW 2060
Merchant Copy
28 OCT 2015 16:00:22
Example of a tip addition transaction record
Note: Graphic will only print on the customer copy of the receipt.
First Data Merchant Solutions
61
Operating your EFTPOS terminal
Reports
Shift
report
The shift report shows each of the following details
for each merchant terminal accessible to the user
requesting the report:
> the shift user from the start date to the end date
is printed along with their ID or name
> the new shift user from the end date is printed
with their ID or name
> the EFTPOS totals provide a summary of all
purchases (including tips), cash out transactions
and refunds per user. The summary shows
the number of occurrences and the subtotal
amounts
> The report then details a pre-authorisation
summary for each user. The summary shows
the number of occurrences and the subtotal
amount. This includes all pre-authorisation
transactions regardless if they’ve been checked
out or not.
> The report details each user’s tip summary last.
This shows the number of occurrences and the
subtotal amount.
If the user is attached to or selects multiple
merchants, the report will include all merchants in
the same printout. Only the first merchant’s details
will display the report header.
Settlement
report
The settlement report contains three separate
sub-reports, as follows:
> the subtotal report displays the subtotals for
purchases, cash outs and refunds for each card
type (non-charge cards), purchases, tips, a
summary of pre-authorisation transactions and
a summary of electronic fallback transactions
in the current period (i.e. since the last
settlement).
> the last settlement report displays the totals for
purchases, cash outs and refunds for each card
type (non-charge cards), purchases, tips, cash
outs and refunds for charge cards, a summary of
pre-authorisation transactions and a summary
of electronic fallback transactions in the last
settlement.
> the previous settlement report displays the
totals for purchases, cash outs and refunds for
each card type (non-charge cards), purchases,
tips, cash outs and refunds for charge cards, a
summary of pre-authorisation transactions and
a summary of electronic fallback transactions
during the previous settlement period.
When the settlement report is printed for all
merchants, it will contain one section for each
merchant accessible to the user who initiates the
tip report function.
You can generate the following reports from the Reports menu.
62
Operating your EFTPOS terminal
Training mode is useful for showing new staff how
to use the terminal to process transactions. When
in this mode, any card transactions will not be
submitted for processing or added to the terminal
amount totals.
Before the terminal can be placed in training
mode, you must perform a settlement to clear out
any existing transactions. The terminal will remain
in training mode until the mode is cancelled,
even if the power is turned off. When in training
mode, the status bar on the idle screen will display
(TRAINING).
All reporting functions are available when
operating in training mode. All transactions
conducted in training mode will be deleted once
training mode is turned off.
Other terminal functionality
Training mode
Daily report
The daily report displays:
> debit totals for all card types
> totals per card type (non-charge cards)
– a summary of all purchases, cash outs
and refunds, with the number of occurrences
and the sub total amounts for each
transaction type
> totals per charge card type – a summary
of all purchases, tips, cash outs and
refund transactions, with the number of
occurrences and the sub total amounts
for each transaction type
> a pre-authorisation summary for all card types.
Transaction report
The transaction report displays selected approved
transactions stored in the terminal. Online
transactions are stored until settlement except for
pre-authorisation transactions, which are kept for
seven calendar days.
63
Operating your EFTPOS terminal
Step 01
Step 05
Select ‘Admin’.
The status bar will now show
the status as (TRAINING).
Step 02
Step 03
Select ‘Next’.
Select ‘Training Mode’.
Step 04
Press the green ‘thumbs up’ button to turn on
training mode or ‘Back’ to return to the Admin menu.
Training off
Training
64
Operating your EFTPOS terminal
The First Data Merchant Solutions EFTPOS
terminal can add a surcharge to every transaction
processed. The surcharge can be either a fixed
dollar amount ($1.00 per transaction, for example)
or it can be a percentage of the total transaction
(2%, for example).
To enable your terminal for surcharging, please
contact the helpdesk on 1800 243 444.
If required, the method of calculation and the
surcharge amount can be different for different
card types. For example, you could set the
terminal to charge all debit cards a set amount per
transaction (such as a. $1.00 surcharge) and all
credit cards could incur a 2% surcharge.
As shown below, the surcharge amount is always
displayed on the customer and merchant receipts.
You can configure your terminal to automatically
calculate the GST on surcharge amounts.
Surcharging
Note: Graphic will only print on the customer copy
of the receipt.
MERCHANT ID 4229851 2345678
TERMINAL ID
12345678
INV NO
000012
STAN
000034
ACCOUNT TYPE Credit
VISA
……..4221(s)
10/15
PURCHASE
$200.00
SURCHARGE $4.00
SURCHARGE GST
$0.40
TIP
TOTAL
XXXX Merchant
123 Sydney Street
North Sydney NSW 2060
Merchant Copy
28 OCT 2015 16:00:22
SIGNATURE
RRN 1234560 00034
APPROVED 08
First Data Merchant Solutions
65
Operating your EFTPOS terminal
Your First Data Merchant Solutions EFTPOS terminal
allows you to add a marketing message to the
bottom of every customer receipt.
Merchants can use this to make their customers
aware of any special deals or discounts.
You can see an example of the customer receipt
marketing message function in the receipt below.
Please contact the helpdesk on 1800 243 444 to
add a marketing message to your customer receipts.
Customer receipt marketing message
Note: Graphic will only print on the customer copy
of the receipt.
GET 15% OFF ALL BAR FOOD AND SNACK ON
MONDAYS, TUESDAYS AND WEDNESDAYS
OPENING HOURS 6AM – 10PM 7 DAYS
MERCHANT ID 4229851 2345678
TERMINAL ID
12345678
INV NO
000012
STAN
000034
ACCOUNT TYPE Credit
VISA
……..4221(s)
10/15
PURCHASE
$200.00
SURCHARGE $4.00
SURCHARGE GST
$0.40
TIP
TOTAL
XXXX Merchant
123 Sydney Street
North Sydney NSW 2060
Merchant Copy
28 OCT 2015 16:00:22
SIGNATURE
RRN 1234560 00034
APPROVED 08
First Data Merchant Solutions
66
Operating your EFTPOS terminal
Card rules
Certain transactions are considered low risk and do
not need to be authorised online. Transactions in
this category are known as off-host transactions.
Below is a list of off-host transaction responses:
Y1 = offline approved
Z1 = offline declined
Y3 = unable to go online and approved offline
Z3 = unable to go online and declined offline.
Electronic fallback
If approved by First Data Merchant Solutions, your
EFTPOS terminal can be configured for electronic
fallback mode.
The First Data Merchant Solutions EFTPOS terminal
will enter electronic fallback mode if there is a
problem transmitting the transaction to the card
issuer. This could be due to a communications error
or due to the issuer being unavailable.
These transactions are known as electronic fallback
(EFB) transactions.
All EFB transactions require signature confirmation
and will be approved with a response code of “08
Approved with signature”. Transactions above
the floor limit will prompt the user to enter an
authorisation number.
You can obtain an authorisation for EFB
transactions by contacting the helpdesk on
1800 243 444.
Please note that in EFB mode, the terminal may
prompt the customer to enter their PIN and
provide their signature. In all cases, please follow
the prompts on your terminal.
Offline transaction processing
Offline transactions are those your terminal approves without contacting the card issuer. The approved
transactions are forwarded to the issuer at a later stage. Offline transactions are allowed for a number of
reasons, outline below.
67
Operating your EFTPOS terminal
Multi-merchant capability
The First Data Merchant Solutions terminal lets you
manage multiple merchant accounts on a single
terminal. This functionality is particularly useful
on premises where there are multiple businesses
sharing space and each has their own merchant
facility.
Multi-merchant capability allows:
> users to be attached to one or all merchant
accounts enabled on the terminal
> different configuration for each merchant
account on the terminal for settings such as
security, reporting and screen layout.
Multi-merchant capability is not a standard feature
enabled on the First Data Merchant Solutions
terminal.
68
Operating your EFTPOS terminal
Hot keys
There are three programmable hot keys that can be set to execute certain functions from the terminal’s
idle screen.
Hot keys provide faster access to frequently used functions.
Hot key assignment options
Once assigned, pressing a function’s hot key will have the same effect as selecting its equivalent key from
the Transaction menu. The following functions can be assigned as hot keys.
> Cashout
> Checkout
> Purchase-ECI
> Purchase-MOTO
> Pre-auth
> Purchase
> Refund
> Settlement
> Tip-addition
> Void
Configuration of hot keys is controlled centrally by First Data Merchant Solutions and cannot be changed
on a terminal.
Programmable hot
keys
69
Operating your EFTPOS terminal
User management
First Data Merchant Solutions terminals can support multiple users. Each user can be flagged as either
a SUPERVISOR or USER and can be associated with one or more merchants. You can set the following
attributes within the context of a user/merchant configuration.
> Trading Name (the merchant’s
name)
> Cashout
> Pre-auth
> Purchase
> Purchase cash
> Purchase tip
> Refund
> Tip
> Void
User configuration is controlled centrally by First Data Merchant Solutions and cannot be changed
on a terminal.
70
Operating your EFTPOS terminal
Shift change
Users can use the shift change function to manage shifts and obtain reports for each shift.
The user who changes the shift becomes the default user for transactions or operations that do not
require user authentication.
Use the following steps to manage shifts and obtain shift reports using the shift change function.
Step 01
Select ‘Admin’.
Step 02
Step 03
Select ‘Next’.
Select ‘Shift’.
Step 04
Key in your user ID and press ENTER.
User Name
NN
71
Operating your EFTPOS terminal
Step 05
Step 08
Key in your password and press ENTER.
Select ‘User’ to print shift totals by user.
Select ‘Card’ to print shift totals by card.
User Password
****
Step 06
Step 07
Select the green ‘thumbs up’ button.
Select the Merchant, if prompted.
Start Shift?
<<Merchant>>
<<Merchant>>
72 Operating your EFTPOS terminal
Where to get help
First Data Merchant Solutions
customer support
Visit the merchant support page at firstdatams.com.au
The site is equipped to keep you up to date with tips and
articles, forms and guides, security and fraud prevention
information and so much more.
Or call
Service and support 1800 243 444
Stationery 1300 664 660
Fraud and risk support 1800 372 838
Keep your merchant ID number handy when you call,
this can help speed up your enquiry.
73
Operating your EFTPOS terminal
Operating your EFTPOS terminal 73
©2015 First Data Corporation. All Rights Reserved. All trademarks, service marks
and trade names used in this material are the property of their respective owners.
Loading...