First Alert 9120B, 9120 User Manual 2

USER’S MANUAL

Smoke Alarms

AC Powered Ionization Smoke Alarm with Silence and Latching Features

Model 9120

Input: 120V AC ~, 60 Hz, 0.04A

AC Powered Ionization Smoke Alarm with Battery Back-up, Silence and Latching Features

Model 9120B

Input: 120V AC ~, 60 Hz, 0.04A

inted in Mexico

Pr M08-0134-003

TANT! PLEASE READ CAREFULLY AND SAVE

IMPOR

s manual contains important information about your Smoke Alarm’s

This user’ operation. If you are installing the Smoke Alarm for use by others, you must leave this manual — or a copy of it — with the end user

K1 04/07

TABLE OF CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Fire Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Before You Install This Smoke Alarm . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

How To Install This Smoke Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Optional Locking Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Understanding the Indicator Lights

and Alarm Horn Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Weekly Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Regular Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

If This Smoke Alarm Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

What To Do In Case Of Fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Using the Silence Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

“Latching Alarm” Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

If You Suspect a Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Recommended Locations For Smoke Alarms . . . . . . . . . . . . . . . . . . . . .6

Locations To Avoid For Smoke Alarms . . . . . . . . . . . . . . . . . . . . . . . . .6-7

About Smoke Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Special Compliance Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Limitations of Smoke Alar

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

.brkelectr

www

eet Road, Aurora, IL 60504-8122

onics.com • www

ms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

.firstalert.com

INTRODUCTION

Thank you for choosing BRK Brands, Inc. for your Smoke Alarm needs. You have purchased a state-of-the-art Smoke Alarm designed to provide you with early warning of a fire.

Key features include: Smart Technology

Single Button Test/Silence eliminates confusion. Depending on what

mode the alarm is in, pushing the button pr as testing the alarm, silencing the alarm, re-testing the alarm when in silence and clearing the Latching feature.

Latching Alarm Indicator easily identifies initiating alarm even after the alarm condition has subsided.

Perfect Mount System includes a gasketless base for easy installation and a new mounting bracket that keeps the alarm secure over a wide rotation range to allow for perfect alignment.

Dust Cover is included to keep the alarm clean during construction. Easy Installation/Maintenance features include a large opening in the

mounting bracket for easy access to wiring. A battery pull tab keeps the

esh until the home is occupied. A Side Load Battery Drawer allows

battery fr for easy battery r wall (Model 9120B only).

Improved UV Resistance keeps the alarm from discoloring over time.

designed to help reduce unwanted or nuisance alarms.

ovides different functions such

eplacement without r

emoving the alarm fr

om the ceiling or

Models 9120

9120B

All First Alert®and BRK®Smoke Alarms conform to regulatory

equirements, including UL217 and are designed to detect particles of

r combustion. Smoke particles of varying number and size are produced in all fires.

Ionization technology is generally more sensitive than photoelectric technology at detecting small particles, which tend to be produced

in greater amounts by flaming fires, which consume combustible materials rapidly and spread quickly. Sources of these fires may include paper burning in a wastebasket, or a grease fire in the kitchen.

Photoelectric technology is generally more sensitive than ionization technology at detecting large particles, which tend to be produced in

greater amounts by smoldering fires, which may smolder for hours before bursting into flame. Sources of these fires may include cigarettes burning in couches or bedding.

For maximum protection, use both types of Smoke Alarms on each level and in every bedroom of your home.

FIRE SAFETY TIPS

Follow safety rules and prevent hazardous situations: 1) Use smoking materials properly. Never smoke in bed. 2) Keep matches or lighters away from children; 3) Store flammable materials in proper containers;

4) Keep electrical appliances in good condition and don’t overload electrical cuits; 5) Keep stoves, barbecue grills, fir

cir debris-free; 6) Never leave anything cooking on the stove unattended;

7) Keep portable heaters and open flames, like candles, away from flammable

materials; 8) Don’t let rubbish accumulate. Keep alarms clean, and test them weekly

are not working properly. Smoke Alarms that do not work cannot alert you to a fire. Keep at least one working fire extinguisher on every floor, and an additional one in the kitchen. Have fire escape ladders or other reliable means of

om an upper floor in case stairs are blocked.

escape fr

eplaces and chimneys gr

. Replace alarms immediately if they

ease- and

BEFORE YOU INSTALL THIS SMOKE ALARM

IMPORTANT! Read “Recommended Locations for Smoke Alarms” and “Locations to Avoid for Smoke Alarms” before beginning. This unit monitors the air

, and when smoke reaches its sensing chamber, it alarms. It can give

e time to escape befor

you mor early warning of developing fires if it is installed, maintained and located where smoke can reach it, and where all residents can hear it, as described in this manual. This unit will not sense gas, heat, or flame. It cannot prevent or extinguish fir

Understand The Different Type of Smoke Alarms

Battery powered or electrical? Different Smoke Alarms provide different types of protection. See “About Smoke Alarms” for details.

Know Where To Install Your Smoke Alarms

Fir level of your home, in every bedr separate sleeping area. See “Recommended Locations For Smoke Alarms” and “Locations To Avoid For Smoke Alarms” for details.

Know What Smoke Alar

A Smoke Alarm can help alert you to fire, giving you precious time to escape. It can only sound an alarm once smoke reaches the sensor. See “Limitations of Smoke Alarms” for details.

Check Your Local Building Codes

This Smoke Alarm is designed to be used in a typical single-family home. It alone will not meet requirements for boarding houses, apartment buildings, hotels or motels. See “Special Compliance Considerations” for details.

es.

e Safety Professionals recommend at least one Smoke Alarm on every

ms Can and Can’

eads. This unit can ONLY give an

e spr

e fir

oom, and in every bedr

t Do

oom hallway or

BEFORE YOU INSTALL THIS SMOKE ALARM, Continued

ELECTRICAL SHOCK HAZARD. Turn off the power to the area where the Smoke Alar Failur injury or death.

m is installed before removing it from the mounting bracket.

e to turn off the power first may result in serious electrical shock,

•

This unit will not alert hearing impaired residents. It is recommended that you install special units which use devices like flashing str lights to aler

•

Installation of this unit must confor area; Articles 210, 760 of NFPA 70 (NEC), NFPA 72, NFPA 101; ICC; SBC (SBCCI); UBC (ICBO); NBC (BOCA); OTFDC (CABO), and any other local or building codes that may apply must be performed by a licensed electrician. Failure to follow these guidelines may r

This unit must be powered by a 24-hour, 120V AC pure sine wave

• 60 Hz circuit. dimmer, or ground fault circuit interrupter. Failure to connect this unit to a 24-hour cir Unit may be connected to an arc fault circuit interrupter.

•

This Smoke Alarm must have AC or battery power to operate. If the AC power fails, battery back-up will allow the alarm to sound for at least 4 minutes. If AC power fails and the batter protection should last for up to 7 days. If AC power fails and the battery is dead or missing, the alarm cannot operate.

•

Never disconnect the power from an AC powered unit to stop an unwanted alar protection. In the case of a true unwanted alarm open a window or fan the smoke away fr when it r a batter smoke, etc.). Instead open a window or fan the smoke away from the unit. The alar

•

Connect this unit ONL Install This Smoke Alarm” for details. Do not connect it to any other type of alarm or auxiliary device. Connecting anything else to this unit may damage it or prevent it from operating properly.

• The battery compartment resists closing unless a battery is installed. This warns you the unit will not operate under DC power without a battery.

• Do not paint over the unit. Paint may clog the openings to the sensing chamber and prevent the unit from operating properly.

t hearing impaired residents.

m to the electrical codes in your

. Wiring and installation

esult in injury or property damage.

Be sure the circuit cannot be turned off by a switch,

cuit may prevent it from providing constant protection.

y is weak,

m. Doing so will disable the unit and remove your

eturns to normal operation. Never remove the batteries from

y operated unit to stop an unwanted alarm (caused by cooking

om the unit. The alarm will reset automatically

m will reset automatically.

Y to other compatible units. See “How To

obe

HOW TO INSTALL THIS SMOKE ALARM

This Smoke Alarm is designed to be mounted on any standard wiring junction box to a 4-inch (10 cm) size, on either the ceiling or wall. Read “Recommended Locations For Smoke Alarms” and “Locations to Avoid For Smoke Alarms” before you begin installation.

Tools you will need: • Needle-nose pliers or utility knife • Standard Flathead screwdriver.

Make sure the Alarm is not receiving excessively noisy power. Examples of noisy power could be major appliances on the same circuit, power from a generator or solar power, light dimmer on the same circuit or mounted near fluorescent lighting. Excessively noisy power may cause damage to your

Alar

TS OF THIS SMOKE ALARM

THE P

The Mounting Bracket:

emove the mounting bracket fr

o r

T Alarm base, hold the Smoke Alarm base firmly and twist the mounting bracket counterclockwise. The mounting bracket installs onto the junction box. It has a variety of screw slots to fit most boxes.

The Power Connector:

The power connector plugs into a power input block on the Smoke Alarm. It supplies the unit with AC power.

• The black wir

• The white wire is neutral.

• The orange wire is used for interconnect.

If you need to r flat screwdriver blade between the power connector and the security tab inside the power input block. Gently pry back the tab and pull the connector fr

e is “hot.”

emove the power connector, insert a

om the Smoke

ee.

The Parts of This Unit

Mounting Bracket

1 2 Mounting Slots

Locking Pins (br

eak out of bracket) 4 Hot (Black) AC Wire 5 Neutral (White) AC Wire 6 Interconnect (Orange) Wire 7 Latch to Open Battery Compartment 8 Swing-Out Battery Compartment

Quick-Connect Power Connector

6 7 8

4 3

}

FOLLOW THESE INSTALLATION STEPS

The basic installation of this Smoke Alarm is similar whether you want to install one Smoke Alarm, or interconnect more than one Smoke Alarm.

f you are interconnecting more than one Smoke Alarm, you MUST read

I “Special Requir you begin installation.

ELECTRICAL SHOCK HAZARD. T will install this unit at the circuit breaker or fuse box before beginning installation. Failur in serious electrical shock, injur

Using wire nuts, connect the power connector to the household wiring.

oper wiring of the power connector or the wiring leading to the

Impr power connector will cause damage to the Alar non-functioning Alarm.

STAND-ALONE ALARM ONLY:

• Connect the white wire on the power connector to the neutral wire in the junction box.

Connect the black wire on the power connector to the hot wire in

• the junction box.

• Tuck the orange wire inside the junction box. It is used for inter

INTERCONNECTED UNITS ONL Strip of

wire on the power connector.

• Connect the white wire on the power connector to the neutral wire in the junction box.

Connect the black wire on the power connector to the hot wire in

• the junction box.

•

Connect the orange wir wire in the junction box. Repeat for each unit you are interconnecting. Never connect the hot or neutral wires in the junction box to the orange interconnect wire. Never cross hot and neutral wires between Alarms.

2. Remove the mounting bracket from the base, and attach it to the junction box.

3. Plug the power connector into the back of the Smoke Alarm. Position the base of the Smoke Alarm over the mounting bracket and

4. turn. The Alarm will remain secure over a wide rotation range to allow for perfect alignment. When wall mounting, this will allow fine-tuning on the positioning to compensate for misaligned wall studs and to keep the wording level. The Alarm can be positioned over the bracket every 120°. Rotate the Alarm until aligned properly.

5. Check all connections.

STAND-ALONE ALARM ONLY:

• If you are only installing one Smoke Alarm, restore power to the junction box.

INTERCONNECTED UNITS ONLY:

• If you are interconnecting multiple Smoke Alarms, repeat steps 1-5 for each Smoke Alarm in the series. When you are finished, restore power to the junction box.

ements For Interconnected Smoke Alarms” below before

urn off power to the area where you

e to turn off the power before installation may result

y or death.

m and may lead to a

connect only.

f about 1/2” (12 mm) of the plastic coating on the orange

e on the power connector to the interconnect

9. For new construction, place supplied dust cover over Alarm to prevent damage fr plete, r

Smoke will not be able to r Cover must be removed!

om dust and construction debris. When construction is com-

emove cover.

each smoke sensor while cover is in place.

SPECIAL REQUIREMENTS FOR INTERCONNECTED SMOKE ALARMS

Failure to meet any of the above requirements could damage the

•

units and cause them to malfunction, removing your protection. AC and AC/DC Smoke Alarms can be interconnected. Under AC

•

, all units will alarm when one senses smoke. When power is

power interrupted, only the AC/DC units in the series will continue to send

eceive signals. AC powered Smoke Alarms will not operate.

and r

Interconnected units can provide earlier warning of fire than stand-alone units, especially if a fir series senses smoke, all units will alarm. To determine which Smoke Alarm initiated an alarm, see table:

During an Alar

On Initiating Alarm(s)

e starts in a remote area of the dwelling. If any unit in the

Red LED(s) flashes (flash) rapidly

On All Other Alarms Red LED is Off

After an Alarm (Latching):

On Initiating Alarm(s)

Green LED(s) On for 2 seconds/Off for 2 seconds

On All Other Alarms Green LED(s) On, Red LED(s) is Off

Compatible Interconnected Units

Interconnect units within a single family residence only. Otherwise all households will experience unwanted alarms when you test any unit in the series. Interconnected units will only work if they are wired to compatible units and all requirements are met. This unit is designed to be compatible with:

First Alert®Smoke Alarm Models SA4120, SA4121B, SA100B and BRK Electronics®Smoke Alarm Models 9120, 9120B, SC6120B, SC9120B, 7010,

7010B, 100S, 4120, 4120B, 4120SB, RM3 (Relay Module); BRK Electronics CO Alarm Models CO5120BN, CO5120PDBN; BRK Electronics®Heat Alarm Models HD6135F and HD6135FB.

Interconnected units must meet ALL of the following requirements:

• A maximum of 18 compatible units may be interconnected

(Maximum of 12 Smoke Alarms).

• The same fuse or circuit breaker must power all interconnected units.

• The total length of wire interconnecting the units should be less than

1000 feet (300 meters). This type of wire is commonly available at Hardware and Electrical Supply stores.

All wiring must conform to all local electrical codes and NFPA 70 (NEC).

•

Refer to NFPA 72, NFPA 101, and/or your local building code for further connection r

equirements.

ELECTRICAL SHOCK HAZARD. Do not restore power until all Smoke Alarms are completely installed. Restoring power before installation is complete may r

Make sur

6. operation, the Green power indicator light will shine continuously.

7. If the Green power indicator light does not light, TURN OFF POWER TO THE JUNCTION BOX and recheck all connections. If all connections

e corr

estore the power, the unit should be replaced immediately.

r Single Station Alarms: Test each Smoke Alarm. Press and hold the

8. Test/Silence button until the unit alarms. Interconnected Alarms: Press and hold the Test/Silence button until the unit alarms. All inter Alarms sounding only tests the interconnect signal between Alarms. It does not test each Alarm’s operation. You must test each Alarm

individually to check if the Alar

If any unit in the series does not alarm, TURN OFF POWER and r connections. If it does not alarm when you r immediately.

esult in serious electrical shock, injur

e the Smoke Alarm is r

ect and the Gr

een power indicator still does not light when you

eceiving AC power

connected Alarms should sound. The other

m is functioning pr

estor

y or death.

. Under normal

e power

operly

, replace it

echeck

Unswitched 120V

60 Hz source

1. Smoke Alarm

2. Ceiling or Wall

3. Power Connector

B. To additional units; Maximum = 18 total

(Maximum 12 Smoke Alarms)

4. Wire Nut

5. Junction Box

6. Neutral Wire (Wht)

7. Interconnect Wire (Orange)

Hot Wir

e (Blk)

+ 4 hidden pages