First Alert 2035DEF User Manual

Operation & Installation Guide

Model / Modèle / Modelo / Modell: 3035DF / 3035DEF / 3040DF / 3040DEF

DELUXE SECURITY BOX

with Digital Electronic Lock

y Carefully!

Read These Instructions V

e ces instructions très attentivement!

Lir

vase leer estas instrucciones cuidadosamente!

¡Sír

MFCB3035DF40DF30809

English

Français

Español

Illustrations

Fig. 1

Fig. 4

English

Fig. 2

Fig. 5

Español

Français

Fig. 3

Fig. 6

Important

EXTERIOR S

IDE VIEW

Overview

elcome to the First Alert

W Products

Along with peace of mind, your First Alert Digital Security Box will provide many years

f secure storage for your valuables.

For security, you should:

mmediately set your own personal

• I

combination.

• Store the keys and personal combination way from the security box.

-set factory code for your safe is:

he pre

amily of

1. Locked override key icon . Override key lock

3. Rotating knob or latching handle

4. Unlocked knob icon

5. LED Indicator light

6. Security box lid

7. Red code setting button

(see diagram to the right)

8. Unlocked override key icon

9. Locked knob icon

10.Digital keypad buttons

11.Security cable attachment hole plug

Your Security Box Includes

• (4) “AA” Batteries

• (1) Foam pad pr protection for your valuables

• (2) Override keys

• (1) Key lock cover

• (1) 4 foot steel secure cable

3040DF, 3040DEF)

(

• (1) Security cable attachment hole plug

(3040DF, 3040DEF)

oviding added

English

Getting Started

STEP 1: Locate Override Keys

Keys and batteries are stor material. Remove them before discarding the box.

STEP 2: Opening your Security Box using your Override Key

Remove cover from key lock. Insert Override Key into key lock and turn

the key counter clockwise one quarter turn to the unlocked position.

Turn the knob counter-clockwise one quarter turn to the unlocked position. (fig.1)

o open, lift fr

T (fig.2)

om the outer edge of the lid.

STEP 3: Installing Batteries

Locate the battery cover on the back side of the lid. (fig.4)

Slide the cover of compartment.

Properly insert batteries, noting correct

ection, r

dir Security Box lid.

Return the Override Key and the knob to the locked position.

NOTE: Clean the battery contacts in the battery compartment and on the batteries befor installing new batteries

eplace cover and close the

ed in the packing

f the battery

English

STEP 4: Opening your Security Box using the pre-set factory code

THE PRE-SET FACTORY CODE IS 3

Using the keypad, enter the factory pre-set code. The LED will flash a green light and stay green for 10 seconds after the button is pressed. Y Security Box unlock.

NOTE: You have 10 seconds to open the Security Box. If the green light goes out, you will have to re-enter the code.

To open, turn the knob from the locked position to the unlocked position, one quarter tur from the outer edge of the lid. (fig.2)

If the LED light flashes r the code, this means the code was entered incorrectly and the Security Box will not open.

NOTE: If an incorrect code is entered 3 times in a row, the Security Box will automatically shut down for 4 minutes before it can be opened again using the correct code. During this delay, the Override Key can be used to open the Security Box.

n counter

ou will hear the

-clockwise. To open, lift

ed after you enter

Programming your Personal Passcode

NOTE: For your security, immediately re-program the digital lock to your Personal Passcode.

Open your Security Box with the Override Key or with the pre-set factory Passcode.

On the inside of the lid, find and press the red button located to the side of the battery compartment (Fig.3). The LED light above the keypad will flash orange.

Enter your personal Passcode, up to 5 digits, followed by the button and then

epeat a second time. You must enter

r the number twice.

For example: 1 2 3 4 5 - 1 2 3 4 5 After the first entry After the second entry green and then go out.

Your Personal Passcode is now saved. Write it down and store it in a secure place

om the Security Box.

away fr Close the lid of your Security Box and

return the knob to the locked position (Fig. 6). If the override key was used, turn to the locked position, remove and replace the lock cover.

NOTE: The factory pr be used to open the Security Box.

, the LED will flash orange.

, the LED will flash

e-set code is no longer active and cannot

Closing and Securing your

NSIDE

IEW

Left side panel

Back panel

XTERIOR

IDE VIEW

EXTERIOR SIDE VIEW

ress Here

Security Box

Be careful not to overfill your Security Box

r obstruct the door from completely

o closing.

Make sure knob is in the unlocked position.

ake sure lid is closed completely. (Fig. 5)

M Turn the knob from the unlocked position

one quarter turn clockwise to the locked position. Your Security Box should now be secured.

OTE: While the override key is in the

N unlocked position you can open and close

he Security Box by turning the knob from

t the locked to the unlocked position and back again without entering your personal code. To secure your Security Box, make sure that you have turned the override key to the locked position and have stored the key away from the Security Box in a safe place.

Troubleshooting

o light from LED: This indicates that the

batteries are expired and need to be replaced. To change the batteries, see Getting Started STEPS 2 & 3.

NOTE: Replacing batteries does not

rase your personal code.

The LED is blinking a red light:

This means that your batteries are low. To change your batteries, see Getting Started STEPS 2 & 3.

Warning: DO NOT FORCE THE KNOB

If forced, the knob will break and your Security Box will be damaged. When operated correctly, the knob will function

o that it can be turned easily into the

s opened position.

f you have additional questions while

perating your Security Box, please

all BRK / SISCO Consumer Affairs at

c 1-800-223-8566. Please call our Consumer Affairs line prior to returning your Security Box to the retailer.

Security Cable

Models 3040DF / 3040DEF include security cable.

emove the plug from

R security cable

ttachment hole.

Loop cable around

esired object and then

hrough itself.

Depress cable release

utton and while holding

own, insert security

d cable into the hole as

hown in diagram, then

elease button.

English

+ 10 hidden pages