User's Manual
Version 1.5
Copyright © 2011. All rights reserved.
All other brand names are registered trademarks of their respective owners.
Gladius Smart
15” All in one POS PC
GLADIUS SMART System manual version 1.4
1
Copyright Notice
This document is copyrighted, © 2011. All rights are reserved. FIRICH ENTERPRISES
CO., LTD. has the right to make improvements of the product described in this manual at
any time without notice.
No part of this manual may be reproduced, copied, translated, or transmitted in any form
or by any means without the prior written permission from FIRICH ENTERPRISES CO.,
LTD.. Information provided in this manual is intended to be accurate and reliable. However,
FIRICH ENTERPRISES CO., LTD. assumes no responsibility for its use, nor for any
infringements upon the rights of third parties, which may result from its use.
The material in this document is for product information only and is subject to change
without notice. While reasonable efforts have been made in the preparation of this
document to assure its accuracy, FIRICH ENTERPRISES CO., LTD., assumes no
liabilities resulting from errors or omissions in this document, or from the use of the
information contained herein.
The software described in this guide is furnished under a license agreement or
nondisclosure agreement. The software may be used or copied only in accordance with
the terms of the agreement.
Product names mentioned herein may be trademarks and/or registered trademarks of
their respective companies.
First Edition Nov. 2011
GLADIUS SMART System manual version 1.4
2
Safety and Warranty
1. Read these safety instructions carefully.
2. Keep this user's manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray
detergents for cleaning. Use a damp cloth.
4. For pluggable equipment, the power outlet must be installed near the equipment and must be
easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall could
cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment from
overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the equipment to the
power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything over the
power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source to avoid
damage by transient over-voltage.
12. Never pour any liquid into an opening. This could cause fire or electrical shock.
13. Never open the equipment. For safety reasons, only qualified service personnel should open
the equipment.
14. If any of the following situations arises, get the equipment checked by service personnel :
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according to the user
manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE
THE STORAGE TEMPERATURE IS BELOW -20° C (-4°F) OR ABOVE 60° C (140° F). IT
MAY DAMAGE THE EQUIPME
GLADIUS SMART System manual version 1.4
3
Table of Content
Chapter 1 Introduction 5
Gladius Smart Characteristics………………………………………………………………………… 5
A Quick Tour of Gladius Smart……………………………………………………………………… 7
Gladius Smart Dimension……………………………………………………………………………. 8
Chapter 2 Hardware Setup 12
Gladius Smart Assembly……………………………………………………………………………...12
Adapter Installatio…………………………………………………………………………………….. 13
2.5” Hard Disk Drive Installation…………………………………………………………………….. 13
Magnetic Card Reader Installation………………………………………………………………….. 14
VFD Customer Display Installation…………………………………………………………………. 15
Second Display Installation………………………………………………………………………….. 15
Cash Drawer Installation…………………………………………………………………………….. 16
Chapter3 Software Installatio 17
Intel Chipset Driver Installation for Windows XP…………………………………………………...18
VGA Driver Installation……………………………………………………………………………….. 20
Audio Driver Installation……………………………………………………………………………… 23
Lan Driver Installation………………………………………………………………………………… 24
ELO Touch Tools Installation………………………………………………………………………... 25
Wireless LAN Driver Installation…………………………………………………………………….. 31
Chapter 4 Specifications 34
Gladius Smart Specifications…………………………………………………………………………34
I/O Pin Definition………………………………………………………………………………………. 36
Second I/O Pin Definition…………………………………………………………………………….. 40
Chapter 5 Troubleshooting 43
Touch Panel does not Work………………………………………………………………………….. 43
Touch Panel Cannot Calibrate Correctly…………………………………………………………… 43
LCD Panel is Not Functioning Properly…………………………………………………………….. 43
MCR is not functioning properly……………………………………………………………………… 43
VFD/LCM Pole Display is not functioning properly………………………………………………… 44
LAN is not functioning properly………………………………………………………………………. 44
Cash Drawer Port is not functioning properly………………………………………………………. 44
GLADIUS SMART System manual version 1.4
4
About this Manual
This manual contains all the information you need to set up and use Gladius Smart.
Chapter 1 Provides an introduction to Gladius Smart and this manual.
Chapter 2 Provides all necessary information for all hardware setup.
Chapter 3 Provides the necessary information for installing for chipset and its accessories.
Chapter 4 Lists all Gladius Smart specifications includes the information of Second I/O
Optional Specifications
Chapter 5 Troubleshooting of Gladius Smart
GLADIUS SMART System manual version 1.4
5
Chapter 1
Introduction
Gladius Smart Characteristics
Gladius Smart is a dual core mobile POS and all-in-one fan-less POS system
of FIRICH ENTERPRISES CO., LTD. The extensible, robust and fan-less
design makes it a perfect solution for retail and hospitality market.
System: A high speed fan-less processor enables to process a high capacity of data
efficiently.
Housing: The solid aluminum housing dissipates the heat inside the system and makes
it a perfect fan-less solution; additionally it also assures the compliance to EMI radiation
testing.
Display: The LCD display can be tilted at multiple angles for operator ease of use.
Extensibility: There are five optional second I/O that customer can choose by their
requirement. In addition to, the VESA mount can be others transforming of this system.
Gladius Smart with
VFD
Gladius Smart with 2nd
Display
GLADIUS SMART System manual version 1.4
6
Detachable Stand Optional LCM
GLADIUS SMART System manual version 1.4
7
A Quick Tour of Gladius Smart
Identification Devices
1st Display
Back I/O
VFD or Monitor
pole stand
Power LED
Wireless Module
LCM
HDD
GLADIUS SMART System manual version 1.4
8
Gladius Smart Dimension
GLADIUS SMART System manual version 1.4
9
Rear I/O Panel (with 5 types of Second IO board)
Type A
I/O Port
Connector Type
Description
COM3
COM5
RJ45 Connector
COM3/COM5 are optional to connect to other
devices.
DC 24V
OUT
3 PIN Socket
24V power out support.
Mic In
Microphone Connector
This is used for allowing usage of microphone.
GLADIUS SMART System manual version 1.4
10
Type B
I/O Port
Connector Type
Description
COM3
COM5
RJ45 Connector
COM3/COM5 are optional to connect to other
devices.
Power USB
24V
Power DIN 4P
The power 24V out is for printer.
Mic In
Microphone Connector
This is used for allowing usage of microphone.
Type C
I/O Port
Connector Type
Description
COM3/COM5
RJ45 Connector
COM3/COM5 are optional to
connect to other devices.
Power USB 12V
Power DIN 4P
The power 12V out is for
printer.
Mic In
Microphone Connector
This is used for allowing
usage of microphone.
Type D
I/O Port
Connector Type
Description
Power USB
12V/24V
Power DIN 4P
The power 24V out is for
printer.
Mic In
Microphone Connector
This is used for allowing
usage of microphone.
Type E
I/O Port
Connector Type
Description
Cash Drawer
24V
RJ11 Connector X 2
Cash Drawer connector, 24V
as default
Mic In
Microphone Connector
This is used for allowing
usage of microphone.
GLADIUS SMART System manual version 1.4
11
Packaging List
Gladius Smart Main System and pedestal integrated with 12V-150w adaptor
AC power cord
RJ45-DB9
GLADIUS SMART System manual version 1.4
12
Chapter 2
Hardware Setup
Gladius Smart Assembly
Please make sure that the system power is turned off and the power supply is disconnected when
making any hardware changes to Gladius Smart.
1. Turn off system power
2. It’s not necessary for detach the base and the main system,
just for your convenience.
Suggestion ：It’s not required to detach the base from the main
system. To detach them will be more helpful for your
convenience.
Remove the back cover and access to the M/B
(Please refer to the Jumper Setting in the 4th chapter.)
RAM
Jumper
Setting
GLADIUS SMART System manual version 1.4
13
Adapter Installation
1. Turn off system power and unplug the cable
2. Release the bracket with one screw
3. Beware of the direction when replacing the adapter
2.5” Hard Disk Drive Installation
1. Turn off system power
2. Open the HDD door on the left of terminal
3. Release HDD carrier with one screw
4. Pull out whole HDD carrier with finger
5. Fix HDD with 4 screws
6. Slide in the HDD carrier to the system
and lock back the screw
Note: If the HDD does not work normally, please refer to troubleshooting
Pull Out
GLADIUS SMART System manual version 1.4
14
Magnetic Card Reader Installation
1. Turn off system power.
2. The socket to connect Identification Devices
can be found on the right side of terminal
3. Attach the MCR module to terminal and
connect the MCR cable to the MCR socket.
4. Lock MCR module to terminal with 2 screws.
Note: If the MCR does not work normally, please refer to troubleshooting.
GLADIUS SMART System manual version 1.4
15
VFD Customer Display Installation
1. Turn off system power.
2. Important, make sure that the jumpers on the M/B are set correctly.
It's important to note that COM4 supplies voltage for the VFD customer display is
set to +12V. If a LCM customer display is chosen, please change it to +5V.
3. Please refer to jumper setting in the 4th chapter.
4. Attach the VFD Mounting stand to the terminal and lock with one screw.
5. Connect the VFD RJ45 cable to COM4 on the I/O board.
6. Turn on VFD power switch and turn on system power.
Second Display Installation
1. Turn off system power.
2. Connect the VGA cable to VGA connector and the DC in cable connect to 12V out.
3. Turn on OSD switch power on and turn on system power.
Note: If the VFD does not display correctly after an application is loaded, please refer to troubleshooting.
GLADIUS SMART System manual version 1.4
16
Cash Drawer Installation
Before connecting the cash drawer to the Gladius Smart, please make sure the driving voltage
and cable pin assignment of the cash drawer matches the definition of the cash drawer port of
Gladius Smart.
Plug cash drawer cable into cash drawer port.
Note: If the cash drawer cannot be detected by the system, please refer to troubleshooting.
Up to two cash drawers may be driven from this port. Driving voltage of the solenoid is
DC+12V. I/O port 284 is used for drawer operation. A test program is supplied, for Linux and
Windows, source code of which is available on request by software developers.
Value
Description
0x284
Output address.
0x284 read 8bit
Bit 2 => 0: low 1: high
0x200
Sleep 200ms
0x01
Open cashdrawer1 value.
0x02
Open cashdrawer2 value.
0x04
Close cash-drawer value.
0x04
Cash-drawer status mask.
COM5COM3
GLADIUS SMART System manual version 1.4
17
CHAPTER3
Software Installation
A. Please go to FEC website and download AL-7435 driver.
B. The installation sequence: Chipset Driver -> VGA Driver -> LAN Driver -> Audio
Driver ->Touch Driver ->Other Driver(optional)
C. Then, you can start to install.
Please follow this installation sequence accordingly.
GLADIUS SMART System manual version 1.4
18
Intel Chipset Driver Installation for Windows XP
Step 1. Please double confirm the Intel chipset driver from website.
Step 2. Click Next
Step 3. Read the License Agreement and click “Yes” to continue
GLADIUS SMART System manual version 1.4
19
Step 4. Click “Next” to continue
Step 5. Click “Next” to continue
GLADIUS SMART System manual version 1.4
20
Step 6. Click “Finish” to complete setup
VGA Driver Installation
Step 1. Please double confirm the VGA driver from website
Step 2. Click “Next” to continue
GLADIUS SMART System manual version 1.4
21
Step 3. Read the License Agreement and click “Yes” to continue
Step 4. Click “Next” to continue
GLADIUS SMART System manual version 1.4
22
Step 5. Click “Next” to continue
Step 6. Click “Finish” to complete setup
GLADIUS SMART System manual version 1.4
23
Audio Driver Installation
Step 1. Please double confirm the Audio driver from website.
Step 2. Click “Next” to continue
Step 3. Click “Finish” to complete setup
GLADIUS SMART System manual version 1.4
24
Lan Driver Installation
Step 1. Please double confirm the LAN driver from website.
Step 2. Click “Next” to continue
Step 3. Click “Next” to continue
GLADIUS SMART System manual version 1.4
25
Step 4. Click “Finish” to complete setup
ELO Touch Tools Installation
ELO Touch Tools Installation for Windows XP/ Windows Vista/
Windows 7
Step 1. Please double confirm the ELO driver from website
Step 2. Click “Next” to continue
GLADIUS SMART System manual version 1.4
26
1. Install Elo Touch drivers and utilities.
2. Tick the Install USB Touchscreen Drivers and click Next to continue
GLADIUS SMART System manual version 1.4
27
3. Read the “License Agreement” and click Yes if you accept it.
4. Select “Auto-detect Elo devices.” and click Next.
GLADIUS SMART System manual version 1.4
28
5. Click Calibrate Elo Touchscreen monitors
6. Using a soft tip object such as finger to calibrate the touch screen (Red bull’s eye will pop
up three time on different position)
ELO Control Panel
This section explains the different options in the ELO control Panel.
General tab
The General tab allows you to calibrate the touch screen with the Align button.
GLADIUS SMART System manual version 1.4
29
Mode tab
The Mode tab allows you to:
Adjust all mouse emulation controls.
Change cursor properties
Enable or disable right mouse button utility.
GLADIUS SMART System manual version 1.4
30
Sound tab
The Sound tab allows you to:
To change sound properties for ELO touch tools.
Properties tab
The Properties tab allows you to:
View Controller Information.
About tab
The About tab displays Information about ELO Touch systems
GLADIUS SMART System manual version 1.4
31
Wireless LAN Driver Installation
Step 1. Please double confirm the Wireless LAN driver from website.
Step 2. Click “Next” to continue
GLADIUS SMART System manual version 1.4
32
1. Select “Install driver and Ralink WLAN Utility”
2. Select “Ralink Configuration Tool”Select “Optimize for WiFi mode”
GLADIUS SMART System manual version 1.4
33
3. Select “Install”
4. Click “Finish”
GLADIUS SMART System manual version 1.4
34
CHAPTER 4
Specifications
Gladius Smart Specifications
System Configuration (Default)
Processor
Intel D525 1.8GHz (Dual Core, L2 cache 1MB)
Chipset
D525+ICH8M
Memory
1 x DDRIII 800MHz SO-DIMM (Up to 4GB)
Size / Resolution
15" / 1024 x 768
Brightness
450 nits (Option:250 nits)
Touch Screen
5W Resistive touch
Serial Port
2 x COM ports (DB-9 male)
1 x COM port (RJ-45) for 12V Customer display
Parallel Port
1 x Parallel port
Standard USB Port
5 x USB 2.0
Keyboard / Mouse Port
1 x PS/2 port
VGA Port
1 x VGA port for 2nd LCD Display
Audio Port
1 x Line-out
Hard Disk Drive
1 x 2.5" SATA type
Speaker
Integrated 2W x 2 stereo speakers
Power Supply
150W 12V External Power Adaptor
Construction
Aluminum
Housing Color / ID
Black
GLADIUS SMART System manual version 1.4
35
Optional LCM
Use COM6 with 5V as default
Thermal Conditions
Fanless Thermal Design
Operating Temperature
0℃ ~ 40℃
O/S Supported
Windows XP (Pro, Embedded), WEPOS, POS Ready2009, Windows 7
Dimensions (W x H xD)
258.61mm x 358.11mm x 269.31mm
EMI/Safety
CE, FCC, RoHS
Second I/O Optional Specifications
I/O Optional-Type A
COM3/COM5
2XCOM Port (RJ45)
Mic In
1X Line in
Power Supply
150W 12V External Power Adaptor
I/O Optional-Type B
COM3/COM5
2XCOM Port (RJ45)
Powered USB Port
24V supported
Mic In
1X Line in
I/O Optional-Type C
COM3/COM5
2XCOM Port (RJ45)
Powered USB Port
12V supported
Mic In
1X Line in
GLADIUS SMART System manual version 1.4
36
I/O Optional-Type E
Cash Drawer Port
1 x 12V RJ11 port (Option: 24V x 2)
Mic In
1X Line in
I/O Pin Definition
A. DC_IN (DC Adapter 12V in)
B. +12V_OUT (12V OUT)
C. COM4_USB1 (VFD & RS-232 port + USB 2.0/1.1 port)
I/O Optional-Type D
Powered USB Port
24supported
Powered USB Port
12V supported
Mic In
1X Line in
Pin
Definition
1
12V
2
GND
3
12V
4
GND
DC_IN
+12V_OUT
Pin
Definition
1
12V
2
GND
COM4_USB1
Pin
Definition
1
RI/ 5V /12V
2
CTS & RTS
3
GND
4
RTS & GND
5
DTR
6
DSR
7
TXD
8
RXD
GLADIUS SMART System manual version 1.4
37
D. USB 2.0/1.1 Port
E. COM2
F. VGA
COM4_USB1
USB_LAN1
Pin
Definition
1
USB 5V
2
D- 3 D+ 4 GND
COM2
Pin
Definition
1
DCD
2
RXD
3
TXD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
RI/ 5V /12V
VGA
Pin
Definition
1
RED
2
GREEN
3
BLUE
4
NC 5 GND
6
GND
7
GND
8
GND
9
VCC 5V
10
GND
11
NC
12
DDC Data
13
H-SYNC
14
V-SYNC
15
DDC Clock
GLADIUS SMART System manual version 1.4
38
G. USB_LAN1 (LAN connector RJ45+USB 2.0/1.1 Port)
H. LPT Port
I. KB_MS1 (PS/2 Connector)
J. RJ11 Port
USB_LAN1
Connection/Speed LED:
State
Description
Orange
Speed:1 Gbps
Green
Speed:1 00 Mbps
State
Description
On
Transmitting
Off
Not Transmitting
Activity LED:
Pin
Definition
1
Data 0+
2
Data 0-
3
Data 1+
4
Data 1-
5
Data 2+
6
Data 2-
7
Data 3+
8
Data 3-
LPT
Pin
Definition
Pin
Definition
1
STB-
14
AFD-
2
PD0
15
ERR-
3
PD1
16
INIT-
4
PD2
17
SLIN-
5
PD3
18
GND
6
PD4
19
GND
7
PD5
20
GND
8
PD6
21
GND
9
PD7
22
GND
10
ACK-
23
GND
11
BUSY
24
GND
12
PE
25
GND
13
SLCT
Pin
Definition
1
Keyboard Data
2
Mouse Data
3
GND
4
Mouse Clock
5
5V
6
Keyboard Clock
RJ11
Pin
Definition
1
GND
2
GPIO-0
3
CASH Drawer Switch
4
12V
5
GPIO-1
6
GND
GLADIUS SMART System manual version 1.4
39
K. AUDIO_JACK (Audio Line Out)
Audio Jack
Pin
Definition
1
GND
2
Line Out (L)
3
AUDIO_JD
4
-ACZ_DET
5
Line Out (R)
GLADIUS SMART System manual version 1.4
40
Second I/O Pin Definition
A. Type A
Pin
Definition
Pin
Definition
Pin
Definition
Pin
Definition
A1
NC
A16
GND
B1
NC
B16
GND
A2
NC
A17
GND
B2
NC
B17
GND
A3
NC
A18
GND
B3
NC
B18
GND
A4
NC
A19
GND
B4
NC
B19
GND
A5
DSR_5
A20
GND
B5
DSR_3
B20
GND
A6
DCD_5
A21
12V
B6
DCD_3
B21
12V
A7
RXD_5
A22
12V
B7
RXD_3
B22
12V
A8
RI_5
A23
12V
B8
RI_3
B23
12V
A9
CTS_5
A24
12V
B9
CTS_3
B24
12V
A10
TXD_5
A25
12V
B10
TXD_3
B25
12V
A11
RTS_5
A26
12V
B11
RTS_3
B26
12V
A12
DTR_5
A27
12V
B12
DTR_3
B27
12V
A13
GND
A28
12V
B13
GND
B28
12V
A14
5V
A29
GND
B14
5V
B29
GND
A15
GND
A30
MIC_L
B15
GND
B30
MIC_R
B. Type B
Pin
Definition
Pin
Definition
Pin
Definition
Pin
Definition
A1
NC
A16
GND
B1
USB5V
B16
GND
A2
NC
A17
GND
B2
D-
B17
GND
A3
NC
A18
GND
B3
D+
B18
GND
A4
NC
A19
GND
B4
USB_GND
B19
GND
A5
DSR_5
A20
GND
B5
DSR_3
B20
GND
A6
DCD_5
A21
12V
B6
DCD_3
B21
12V
A7
RXD_5
A22
12V
B7
RXD_3
B22
12V
A8
RI_5
A23
12V
B8
RI_3
B23
12V
A9
CTS_5
A24
12V
B9
CTS_3
B24
12V
A10
TXD_5
A25
12V
B10
TXD_3
B25
12V
A11
RTS_5
A26
12V
B11
RTS_3
B26
12V
A12
DTR_5
A27
12V
B12
DTR_3
B27
12V
A13
GND
A28
12V
B13
GND
B28
12V
A14
5V
A29
GND
B14
5V
B29
GND
A15
GND
A30
MIC_L
B15
GND
B30
MIC_R
GLADIUS SMART System manual version 1.4
41
C. Type C
Pin
Definition
Pin
Definition
Pin
Definition
Pin
Definition
A1
NC
A16
GND
B1
USB5V
B16
GND
A2
NC
A17
GND
B2
D-
B17
GND
A3
NC
A18
GND
B3
D+
B18
GND
A4
NC
A19
GND
B4
USB_GND
B19
GND
A5
DSR_5
A20
GND
B5
DSR_3
B20
GND
A6
DCD_5
A21
12V
B6
DCD_3
B21
12V
A7
RXD_5
A22
12V
B7
RXD_3
B22
12V
A8
RI_5
A23
12V
B8
RI_3
B23
12V
A9
CTS_5
A24
12V
B9
CTS_3
B24
12V
A10
TXD_5
A25
12V
B10
TXD_3
B25
12V
A11
RTS_5
A26
12V
B11
RTS_3
B26
12V
A12
DTR_5
A27
12V
B12
DTR_3
B27
12V
A13
GND
A28
12V
B13
GND
B28
12V
A14
5V
A29
GND
B14
5V
B29
GND
A15
GND
A30
MIC_L
B15
GND
B30
MIC_R
D. Type D
Pin
Definition
Pin
Definition
Pin
Definition
Pin
Definition
A1
USB5V
A16
GND
B1
USB5V
B16
GND
A2
D-
A17
GND
B2
D-
B17
GND
A3
D+
A18
GND
B3
D+
B18
GND
A4
USB_GND
A19
GND
B4
USB_GND
B19
GND
A5
NC
A20
GND
B5
NC
B20
GND
A6
NC
A21
12V
B6
NC
B21
12V
A7
NC
A22
12V
B7
NC
B22
12V
A8
NC
A23
12V
B8
NC
B23
12V
A9
NC
A24
12V
B9
NC
B24
12V
A10
NC
A25
12V
B10
NC
B25
12V
A11
NC
A26
12V
B11
NC
B26
12V
A12
NC
A27
12V
B12
NC
B27
12V
A13
GND
A28
12V
B13
GND
B28
12V
A14
NC
A29
GND
B14
NC
B29
GND
A15
GND
A30
MIC_L
B15
GND
B30
MIC_R
GLADIUS SMART System manual version 1.4
42
E. Type E
Pin
Definition
Pin
Definition
Pin
Definition
Pin
Definition
A1
NC
A16
GND
B1
NC
B16
GND
A2
NC
A17
GND
B2
NC
B17
GND
A3
NC
A18
GND
B3
NC
B18
GND
A4
NC
A19
GND
B4
NC
B19
GND
A5
NC
A20
GND
B5
NC
B20
GND
A6
NC
A21
12V
B6
NC
B21
12V
A7
NC
A22
12V
B7
NC
B22
12V
A8
NC
A23
12V
B8
NC
B23
12V
A9
CTS_5
A24
12V
B9
CTS_3
B24
12V
A10
TXD_5
A25
12V
B10
TXD_3
B25
12V
A11
NC
A26
12V
B11
NC
B26
12V
A12
NC
A27
12V
B12
NC
B27
12V
A13
GND
A28
12V
B13
GND
B28
12V
A14
5V
A29
GND
B14
5V
B29
GND
A15
GND
A30
MIC_L
B15
GND
B30
MIC_R
GLADIUS SMART System manual version 1.4
43
CHAPTER 5
Troubleshooting
Please note that the following troubleshooting guide is designed for people with strong
computer hardware knowledge such as System Administrators and Engineers.
Touch Panel does not Work
A) Check if the touch driver has been properly installed. Or try to reinstall again (Please refer
to the touch driver installation).
B) Move back cover, check all relative cables for touch controller.
C) If touch controller does not appear green light, it could be defective.
Touch Panel Cannot Calibrate Correctly
A) Please try to re-install touch driver and re-calibrate again. If not, the touch controller and
touch panel could be defective.
LCD Panel is Not Functioning Properly
A) Check that the LCD driver is installed properly (Please refer to the LCD driver installation
section).
B) Connect a LCD or CRT monitor to the VGA connector, if there is a display, then the LCD
panel could be defective or is not installed properly.
C) Move back cover, check all the LCD relative cables. (For example: check LVDS, inverter
whether they are properly.)
MCR is not functioning properly
A-1) Check if the MCR is properly connected to the MCR connector board on main
system.
A-2) Make sure the MCR 12PIN cable is properly connected to the right side wafer
(which is USB hub board) of LCD.
A-3) The USB hub board could be defective.
A-4) The MCR module could be defective.
GLADIUS SMART System manual version 1.4
44
VFD/LCM Pole Display is not functioning properly
A) Ensure that COM4 is enabled in the CMOS setup, and data is written to COM4 in the
application.
B) Ensure the jump setting of COM4 ,please refer the M/B manual.
C) Check if there is any display when system power is ON, if the screen is blank, please
follow the steps below.
B-1) Make sure the power switch on the VFD display is on before powering the main
system.
D) Check RJ-45 cable is properly connected to I/O
E) Check the cable is properly connected to main board
F) The on-board COM4 I/O chips could be defective.
LAN is not functioning properly
A) Check if the LAN driver is installed properly. (Please refer to the LAN driver installation)
B) Check if there are any IRQ conflicts.
C) Check if the RJ45 cable is properly connected.
D) The on board LAN chip could be defective.
Cash Drawer Port is not functioning properly
A) Make sure the pin assignment matches between the cash drawer and the RJ11 cash
drawer port
B) Verify the digit I/O port address is 284
C) The motherboard could be defective
Loading...