©2006 INVENSYS CONTROLS AMERICAS
Carbon Monoxide Alarm
110-1125C
SERIES 10000
MODEL COE: 120 V AC/DC CARBON MONOXIDE ALARM
WITH BATTERY BACKUP
SERIES 10200
MODEL COE-B: DC ONLY CARBON MONOXIDE ALARM
SERIES 10400
MODEL COEA: 120 V AC CARBON MONOXIDE ALARM
PLEASE READ AND SAVE THIS ENTIRE MANUAL
Installer: Please leave this manual with the product
Electrical rating:
120V AC, 60Hz, 0.05amp
Single or multiple station CO alarm
Model COE includes 9V battery back-up
TABLE OF CONTENTS
About This Carbon Monoxide Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Specifications and Important Product Information . . . . . . . . . . . . . . . . . . . . . . . .1
Where to Install This CO Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
How To Install This CO Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
1. Installing an AC With Battery Back-Up Alarm . . . . . . . . . . . . . . . . . . . . . . . .3
2. Interconnecting AC Only and AC/DC Alarms . . . . . . . . . . . . . . . . . . . . . . . .3
If the Alarm Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Chart : Understanding the LED Lights and Horn Patterns . . . . . . . . . . . . . . .5 & 6
Troubleshooting the CO Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 & 6
Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Symptoms of CO Poisoning and sources of CO in the home
Testing and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Service and Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
The following symbols identify the most important safety messages in
this manual.
When you see this symbol, be aware that if the
DANGER
WARNING
CAUTION
About this Carbon Monoxide Alarm:
message is ignored, the hazard WILL result in
SEVERE bodily injury or death.
When you see this symbol, be aware that if the
message is ignored, the hazard CAN cause
SEVERE bodily injury or death.
When you see this symbol, be aware that if the
message is ignored, the hazard CAN or WILL
cause MINOR bodily injury.
This CO alarm is designed to detect carbon monoxide gas. It is NOT designed to
detect smoke, fire, or any other type of gas. If this CO alarm sounds its alarm
horn, DO NOT assume that it is a false alarm. The alarm horn requires your
immediate action.
WARNING
Individuals with medical problems may consider using warning devices which provide
audible and visual signals for carbon monoxide concentrations under 30ppm.
SPECIFICATIONS AND IMPORTANT
PRODUCT INFORMATION
Product Features
• Monthly Self-Test: Approximately every 30 days this alarm performs a silent
internal system test to verify sensor operation utilizing True Gas Testing. True
Gas Testing verifies that the CO sensor is nearing the end of its service life.
Traditional CO alarms test the sensor by simulating an alarm condition electrically.
This is the first CO sensor that runs a diagnostic test by generating a very small
and harmless amount of hydrogen gas. If the sensor is working properly, it WILL
NOT chirp. If the alarm chirps during the monthly self-testing, it is indicating a
problem with the unit. Refer to the charts on pages 5 and 6 for the appropriate
actions to take should this occur. You must still test the alarm weekly to verify
proper horn operation.
• Trigger Alarm Locator™ (TAL™): Most interconnect tests trigger all alarm horns
simultaneously for the duration of the test. This unique system alternates between
a 10 second ALL ON cycle and a 50 second cycle where only the initiating alarm
is sounding.
• Alarm Controlled Interconnect Test: In an interconnected system, this feature
will alarm the local unit first, then quiet the local unit while the remote units alarm.
• Smart Quiet™ Low Battery 1: Allows the homeowners to silence the low battery
chirp for up to 10 hours, giving them time to go back to sleep and/or purchase a
fresh replacement battery.
• Smart Quiet™ Low Battery 2: Indicates the battery no longer has enough
voltage to adequately protect in the event of a power outage or a battery-only
installation. The Smart Quiet™ feature will no longer silence the chirp.
THE BATTERY MUST BE REPLACED IMMEDIATELY.
Required Power Supply (Series 10000 and 10400 only)
• This CO alarm requires constant 120-volt, AC power AND/OR a working 9-volt
battery to operate properly. This alarm WILL NOT work if AC power is not
connected or has failed or been interrupted for any reason AND the battery is
removed, drained or improperly connected. DO NOT use any other kind of battery
except as specified in this manual.
1
NOTE: AC/DC alarms offer added protection in the event of a power failure or a
drained battery.
• DO NOT remove or disconnect the battery or turn off AC power to quiet unwanted
alarms. This will remove your protection. This alarm features a Quick Quiet™ False
Alarm Control button which, when activated, will quiet unwanted CO alarms for up
to 6 minutes.
Installation/Interconnect
• This CO alarm should be installed only by a licensed qualified electrician. Observe
and follow all local and national electrical and building codes for installation.
• Unique power connector prevents interconnection with incompatible smoke and
combination alarms or security systems.
• This CO alarm may be interconnected with as many as 12 other Firex model
FADC, AD, ADC, PAD, G, or TPCI smoke alarms, and as many as 5 Firex model
ADH heat alarms or COE and COEA CO alarms for a total of not more than 18
interconnected devices.
WARNING
• DO NOT connect this CO alarm to any other type of smoke, CO, heat, or com-
bination alarm or auxiliary device except those listed in this manual.
• While AC and AC/DC smoke, CO and heat alarms can be interconnected,
ONLY when AC power is ACTIVE will ALL units ALARM when one unit senses
a hazardous condition. WHEN AC power is DISCONNECTED, INTERRUPTED
OR NOT PRESENT FOR ANY REASON, ONLY AC/DC UNITS WILL CONTINUE
TO SEND AND RECEIVE SIGNALS AND SOUND AN ALARM IN RESPONSE TO
THE PRESENCE OF SMOKE. WHEN power is DISCONNECTED, INTERRUPTED
OR NOT PRESENT FOR ANY REASON, AC powered smoke, CO, or heat
alarms WILL NOT OPERATE!
Compliance and Proper Applications
• This CO alarm is designed to be used inside a single-family household. In
multi-family buildings, each individual living unit should have its own alarms. It is
not a substitute for a complete commercial alarm system. It should be used only
as supplemental protection in hotels, motels, dormitories, hospitals, nursing
homes, or group homes.
• This product is intended for use in ordinary indoor locations of family living units.
It is not designed to measure compliance with Occupational Safety and Health
Administration (OSHA) commercial or industrial standards.
NOTE: Enclosed with this CO alarm are two labels detailing actions to take in
the event of an alarm. One should be placed next to the CO alarm; the other
should be placed near a source of fresh air. Please provide the telephone number of the emergency provider and a qualified technician on each label.
WHERE TO INSTALL THIS CO ALARM
About Locating CO Alarms
Carbon monoxide gas can be anywhere and everywhere. CO gas is equal to or
slightly lighter than air, and disperses evenly with the air in a room. Therefore,
install this CO alarm where air circulation is best. Since most CO fatalities occur
while families are sleeping, we recommend that you install at least one CO alarm
in the hallway outside each separate sleeping area and one inside each bedroom
or sleeping area.
We also recommend that you install a CO alarm on every separate living level
of the home where household members frequently spend time, as well as in
the basement.
This CO alarm can share the interconnect wire of smoke and heat alarms,
BUT this alarm will remain silent if smoke or high heat is detected by the
interconnected smoke and heat alarms. Therefore it is necessary to install
both a CO alarm and smoke alarm or a smoke/CO combination alarm in
those areas to be fully protected.
This alarm will indicate only the presence of carbon monoxide gas at the
sensor. Carbon monoxide gas may be present in other areas.
BEDROOM BEDROOM BATH
FURNACE
ROOM
BASEMENT
single story double story
FIGURE 1
CAUTION
LIVED-IN ATTIC
BEDROOM BATH BEDROOM
LIVING
ROOM
FURNACE
BASEMENT
FIGURE 2
BEDROOM BATH
BEDROOM
FAMILY/GREAT ROOM
KITCHEN
ROOM
KITCHEN
LIVING
ROOM
UTILITY
ROOM
BASEMENT
BATH
split level
FIGURE 3
KEY: CO Alarm Locations
WARNING
DO NOT install CO alarms:
• Near bathrooms or in shower areas. Steam and aerosol sprays can disable
the alarm.
• In closets, crawlspaces, unused attics, or unheated areas where surrounding air
temperatures man go below 40ºF (4.4ºC) or above 100ºF (37.8ºC).
• Within five feet of any fuel-burning appliance (stove, kerosene heater, furnace,
fireplace, etc.).
• Within one foot of any wall, corner, or other dead air space.
• In rooms where chemicals or cleaning supplies are frequently used (paint,
hair spray, thinner, etc.). Allow plenty of ventilation in rooms where chemicals
are used.
• Directly above a sink, bathtub or basin.
• Directly above or below air exchange or heating vents.
• Behind drapes, furniture, or appliances that could block air flow to the CO alarm.
WARNING
This unit cannot be used in recreational vehicle applications.
HOW TO INSTALL THIS CO ALARM
This alarm can be mounted and operated in one of three ways: 1. Battery (DC)
Only Stand Alone, 2. AC With a Junction Box, and 3. Interconnected AC Only and
AC/DC Alarms.
2
Do not use super glue or silicon caulk on or near the alarm! Fumes from
these products can coat and permanently damage the sensor.
Installing a Battery (DC) Only Stand-Alone Alarm
Model COE-B (10200 Series)
CAUTION
1. Remove the mounting plate. Hold the alarm and turn the mounting plate clockwise
to separate it from the back of the alarm.
2. Hold the mounting plate against the ceiling or wall in the desired position and use
a pencil to trace the mounting holes.
3. Use a 3/16” (5mm) drill bit to drill through the center of the outlines you made in
Step 2.
4. Insert screw anchors into the drilled holes. If necessary, gently tap anchors with
a hammer until they are flush with the mounting surface.
5. Attach the mounting plate to the mounting surface with the mounting screws
provided.
6. Position the alarm on the mounting plate and turn clockwise to lock it into place.
7. Pull out the battery activation strip. The alarm will respond with one yellow
light flash.
8. Test the alarm. See “TESTING AND MAINTENANCE” for details.
Installing With a Junction Box
Models COE (10000 Series) and COEA (10400 Series)
ELECTRICAL SHOCK HAZARD. Turn off power at the main fuse box or circuit
breaker by removing the fuse or switching the circuit breaker to the OFF position.
WARNING
This CO alarm should be installed only by a qualified electrician. Carbon
Monoxide alarm installation must be in accordance with the requirements of
Article 760 of the National Electrical Code and any local codes that may apply.
• Install CO alarm on any 4-inch or single gang junction box only.
1. From box of CO alarm, remove mounting plate.
2. Align recessed slots on plate with mounting holes
of any 4-inch or single gang junction box.
3. Gently pull household wires through center hole
of plate.
4. Secure plate to junction box using mounting screws.
5. With a small wire connector, connect white wire from
connector plug to white household wire.
6. Connect black wire from connector plug to black
household wire.
7. To interconnect alarms, connect
yellow wire from connector to
interconnect wire between other
combination or smoke alarms.
DANGER
Before starting, see “INTERCONNECTING AC and AC/DC
ALARMS.”
NOTE: For a single-station alarm,
cover yellow wire with
electrical tape and tuck into
junction box.
8. Attach connector plug to pins on back of combination alarm. Plug will only fit
one way and will snap into place. Gently tug connector to be sure it is
attached securely.
9. Position the CO alarm to mounting plate and turn clockwise to lock into place.
10. Turn on power at main fuse box or circuit breaker.
11. Test CO alarm. See “TESTING THE CO ALARM.”
12. Model COE only: Activate the battery. Remove arrow tab and close battery
door. The yellow light will flash as door is closed.
WHITE
YELLOW
BLACK
FOR INTERCONNECT: USE #18 AWG MINIMUM WIRE
WHITE
YELLOW
BLACK
WHITE
BLACK
TO NEUTRAL
TO 120V AC
Interconnecting AC Only and AC/DC Alarms
DANGER
ELECTRICAL SHOCK HAZARD. Turn off power at the main fuse box or circuit
breaker by removing the fuse or switching the circuit breaker to the OFF position.
WARNING
This CO alarm should be installed only by a qualified electrician. Carbon
Monoxide alarm installation must be in accordance with the requirements of
Article 760 of the National Electrical Code and any local codes that may apply.
• Use #18 AWG minimum solid or stranded wire. When interconnecting, maximum
wire length between any two is 1,500 feet for #18 AWG or 4,000 feet for #14 AWG
(20 OHMS loop resistance).
• This CO alarm may be interconnected with as many as 12 other Firex model
FADC, AD, ADC, PAD, G or TCPI smoke alarms, and as many as 6 Firex model
ADH heat alarms or COE and COEA CO alarms for a total of not more than 18
interconnected devices. DO NOT connect to any other type or model combination
smoke, or CO alarm.
WARNING
While AC and AC/DC smoke, CO and heat alarms can be interconnected, ONLY
when AC power is ACTIVE will ALL units ALARM when one unit senses a hazardous condition. WHEN AC power is DISCONNECTED, INTERRUPTED OR NOT
PRESENT FOR ANY REASON, ONLY AC/DC UNITS WILL CONTINUE TO SEND
AND RECEIVE SIGNALS AND SOUND AN ALARM IN RESPONSE TO THE PRESENCE OF SMOKE., CO, OR HEAT, AS DETERMINED BY THE MODEL OF ALARM
THAT IS PRESENT. WHEN power is DISCONNECTED, INTERRUPTED OR NOT
PRESENT FOR ANY REASON, AC powered smoke, CO, or heat alarms WILL
NOT OPERATE.
• Connect CO and smoke alarms to a single dedicated AC branch circuit. If local
codes do not permit such a wiring configuration or connection, be sure the neutral
wire is common to both circuits or phases.
Installing AC/DC CO Alarms as Replacements with
Interconnected Legacy Firex Alarms
Model COE and COEA CO alarms are designed to be used as replacement units for all
Firex AC and AC/DC CO alarms with a low voltage interconnect line. All models listed
use a 3-wire interconnect system. To interconnect with other models, please call our
free technical support line at (800) 445-8299.
3
IMPORTANT! READ BEFORE INSTALLING THIS CO ALARM WITH EXISTING
In residential homes, there are two ways smoke and CO alarms are hardwire installed
and interconnected. One uses 4 wires, the other uses 3 wires.
CO alarms can be used with both 4 and 3 wire systems.
COEA
1. Identify whether the installed system uses 3 or 4 wires to interconnect.
2. If a 4-wire system is installed, change the system to a 3-wire by connecting the
independent interconnect wires (yellow and blue) at any point in the system.
3. Smoke alarms generally don’t require any changes (other than replacement every
ten years).
4. Replace older CO alarms on the new 3-wire system with COE and COEA CO
alarms. These alarms can discriminate between signals coming from a smoke
alarm and signals coming from a CO alarm. Older model CO alarms converted to
3-wire cannot. So when any alarm is triggered, all the older CO alarms will sound,
creating confusion about which danger is actually present.
To Install a CO alarm as a Replacement:
1. Turn off AC power at circuit breaker or main fuse box.
2. Remove old alarm from mounting bracket.
3. Disconnect wire connector from back of unit.
4. Remove wire nuts and connect new wire connector to household wiring. Be
certain not to cross the wiring.
5. Connect wire connector to back of alarm.
6. If mounting bracket is the same, reattach alarm to mounting bracket. Feed wiring
back through hole in mounting surface.
7. Turn on power at main fuse box or circuit breaker.
8. Test CO alarm. See “TESTING THE CO ALARM.”
9. Model COE only: Activate the battery. Remove arrow tab and close battery
yellow light will flash as door is closed.
INTERCONNECTED FIREX ALARMS
The model
COE and
IF THE ALARM SOUNDS
If Your CO Alarm Sounds (and you are not testing it)
Carbon Monoxide has no taste, feel or smell – but it can be FATAL.
IF 1 RED LIGHT IS FLASHING AND THE HORN SOUNDS 4 ALARMS APPROXIMATELY EVERY FIVE SECONDS, IT INDICATES THE PRESENCE OF CO WHICH
CAN BE FATAL. YOU MUST QUICKLY DO THE FOLLOWING:
1. Operate Test/Reset button;
2. Call your emergency services [fire department or 911]
3. Immediately move to fresh air — outdoors or by an open door/window. Make certain that all persons are accounted for. Do not reenter the premises or move away
from the open door/window until the emergency services responders have arrived,
the premises have been aired out, and your alarm remains in its normal condition.
4. After following steps 1 - 3, if your alarm reactivates within a 24 hour period, repeat
steps 1 - 3 and call a qualified appliance technician (__________________) to investigate sources of CO from fuel burning equipment and appliances, and to inspect
for proper operation of this equipment. If problems are identified during this
inspection, have the equipment serviced immediately. Note any combustion equipment not inspected by the technician and consult the manufacturers’ instructions
or contact the manufacturers directly for more information about CO safety and
this equipment. Make sure that motor vehicles are not, and have not been, operating in an attached garage or adjacent to the residence.
If the CO alarm sounds its alarm horn again, it has sensed CO. This is not a
false alarm.
TO TEMPORARILY SILENCE AN ALARM
NOTE: These features temporarily quiet alarms, but do not disable the sensor.
Quick Quiet™CO Reset
Pushing the Smart Button initiates the
CO reset, which quiets all alarms, including the one you touched.
This means the unit nearest you
triggered the alarm.
WARNING
™
Smart Quiet
Pushing the Smart Button quiets
all alarms EXCEPT the one that
triggered the alarm.
This means the unit still
sounding triggered the alarm.
These features help you identify the trigger alarm(s) and areas of immediate
danger to avoid under alarm conditions. After one minute if a dangerous condition
persists all units will go back into alarm
the initiating alarm will sound for 50 seconds. This 10-second/50-second alarm
pattern will keep repeating until the air is cleared and the immediate danger
has passed.
MOVE AWAY from areas where you hear trigger alarms sounding if at all
possible. DO NOT IGNORE the trigger alarm(s), and be aware that an extremely
dangerous situation exists at that location(s) in your home.
Trigger Alarm Locator
: all alarms will sound for 10 seconds, then just
Latching LED Alarm Indicator
The Latching LED Alarm Indicator activates automatically, and helps you identify the
original trigger alarm(s) in an interconnected series after a smoke or CO event.
CO Alarm - after a CO alarm condition, the single RED light on the triggering alarm(s)
blinks 3 times every 10 seconds until manually reset.
Smart Quiet™ for Low Battery Alert
You can silence the Low Battery Alert for up to 10 hours by pressing and releasing the
Smart Button. The sensor remains active. This allows you and your family to go back
to sleep or gives you time to purchase a replacement battery. It is important that you
replace the battery as soon as possible to continue your protection!
4
UNDERSTANDING THE ALARM
CONDITION
AC power is present
Standby condition
Push-to-Test
(Local Test Only)
Press-and-Hold
(Local and Interconnect Tests)
Smart Quiet™ Low-Battery #1
Smart Quiet™ Low-Battery #2
Fault condition
Local CO condition is detected
HORN
Horn beeps once per minute
Horn beeps once per minute
Horn sounds two quick beeps
every minute
Horn sounds 4 short tone
patterns every 5 seconds
Local CO condition is latched
Quick Quiet™ CO Reset is
activated
Remote signal is received from
another CO alarm
DANGER
PROBLEM
GREEN light is not on.
Alarm does not sound
and lights do not flash
when unit(s) is tested.
NOTE: Push and hold
Smart Button for at least
5 to 10 seconds if unit
does not
sound!
SOLUTION
1. Alarm may be functioning properly on DC (battery)
2. Check AC power supply at fuse box or breaker panel.
3. Alarm wiring is improperly connected. Have wiring
1. Check that AC power is turned on (GREEN light ON);
2. Turn off power. Remove alarm from mounting plate
3. Clean alarm (see “Cleaning” on page 8).
Horn sounds 4 short tone patterns every 5 seconds
TROUBLESHOOT
Always turn off power at main fuse box or circuit
breaker before taking troubleshooting action.
power if YELLOW light flashes once per minute.
checked by a licensed electrician. Retest the alarm.
check that a good battery is inserted correctly in the
battery compartment; check that the battery door is
tightly closed.
and check that connector plug is securely attached.
Interconnected smoke,
heat, or CO alarms do
not sound when
Button is pushed to test
units
.
Smart
1. Press and hold the Smart Button longer until the
second set of two quick beeps sounds to initiate the
remote test.
2. Check that remote alarms are receiving power and
functioning properly
3. Alarm interconnect circuit problem. Replace
and retest.
4. On DC (battery powered) interconnected alarms,
remove alarm from mounting bracket and check that
the connector plug is securely attached.
5. On an interconnected series with both AC and AC/DC
powered units, wiring may have been improperly
connected. Have wiring checked by a licensed
electrician. Retest all alarms in the series.
5
LED AND HORN PATTERNS
LIGHTS
GREEN light ON
YELLOW light blinks once per
minute
YELLOW light blinks during horn
ramp-up.
RED blinks 4 times right after
horn sounds.
YELLOW light blinks during horn
ramp-up.
RED blinks 4 times right after
horn sounds.
YELLOW light flashes 2 times per
minute after horn beeps
YELLOW light flashes 3 times per
minute after horn beeps
YELLOW light flashes constantly
after horn beeps
RED light flashes 4 times right
after horn
SMART BUTTON KEY
Quick push activates a local
Push-to-Test sequence
Press and RELEASE button
before you hear the third chirp.
The system will perform a single
local test cycle.
Press and HOLD button.
The system will perform a single
local test cycle, then repeat the
interconnect test until you release
the button.
Quick press will eliminate the
low-battery warning for about 10
hours
Smart Button WILL NOT silence
the low battery chirp! Replace
battery immediately!
Press to check the alarm again.
Replace alarm if it remains in the
fault condition.
Quick press activates CO Reset
RED light flashes 3 times every
10 seconds
RED light flashes 1 time every
10 seconds
WARNING
DO NOT disconnect the battery or AC power
to quiet an unwanted alarm. This will remove
your protection.
Use Quick Quiet™ False Alarm Control by
pushing the Smart Button.
PROBLEM
The horn beeps once,
then two beeps, then
three beeps, pauses, and
then sounds the full
alarm when using the
Smart Button to test.
Quick press erases the CO
latched signal
Quick press activates Smart
Quiet™ Trigger Alarm locator for
Model COE and COEA alarms.
SOLUTION
The alarm is operating properly. The Firex patented
Horn Ramp-Up feature lets you start the test sequence
and move away from the unit before the full alarm
horn sounds.
Alarm sounds;
no hazard present.
The alarm beeps once a
minute and YELLOW
light flashes.
Horn beeps twice a
minute and YELLOW
light flashes.
For Technical Support:
PH: (800) 445-8299
Email: technical service@invensys.com
Website: www.icca.invensys.com/firex
Take Emergency Safety Actions in all alarm situations! If
no hazard proves to be present: Test the alarm to check
for proper functioning. Clean the alarm. (See TESTING
AND MAINTENANCE.) Check that the alarm is placed
properly. (See AGENCY RECOMMENDATIONS FOR
ALARM PLACEMENT.)
The battery needs to be replaced. Turn off power and
replace the battery. (See “REPLACING THE BATTERY” in
“TESTING AND MAINTENANCE”.) Push the Smart Button
to temporarily quiet the low battery signal for 10 hours.
Push the Smart Button to allow alarm to reset and self
test. If fault signal continues, alarm is no longer providing
protection and must be replaced.
6
IMPORTANT SAFETY INFORMATION
CO Home Safety Tips
CO poisoning is often caused by equipment failures due to poor maintenance, prod-
uct defects, and damaged parts. The following tips can help prevent CO within
your home:
1. Have all fuel-burning appliances inspected and cleaned yearly by a qualified service technician. The furnace, water heater, and stove are some of the
leading sources of CO.
2. Clean fireplace vents and chimney regularly. A blocked chimney could cause
a backdraft of CO into the home. Do not seal chimney. This will cause a
backdraft of CO into the home.
3. Do not seal a draft hood or exhaust vent to any appliance. This will trap
dangerous CO inside the house.
4. Do not close off or confine your fuel-burning appliances in a closed area.
They need plenty of ventilation to operate properly.
5. Do not use liquid propane (LP) or charcoal grills or operate any gasoline
powered equipment indoors.
6. Allow for plenty of ventilation when using a kerosene heater. Do not use in
small areas.
Preventive maintenance, common sense, and a CO detection device are some of the
best methods of preventing CO poisoning. However, a dangerous situation can
happen to anyone at any time.
The following list illustrates some danger signs of CO presence.
1. Soot and dirt build-up seeping out of chimney or other exhaust vents.
2. A mostly yellow (rather than clear blue) burner flame or pilot flame in gas appliances.
3. A draft of air coming from an appliance, chimney, or vents.
4. Car idling in an open or closed attached garage, or near a home.
If you have flu-like symptoms or suspect CO poisoning, seek medical
assistance immediately!
Symptoms of Carbon Monoxide Poisoning
CO poisoning has many symptoms. Some are very similar to the flu, the effects
of intoxication, or drug usage. In many CO cases, people feel ill and stay home to
rest. This only compounds the CO poisoning because they stay in the home where
CO is present.
As CO levels rise, the symptoms become more extreme. At low levels people will
suffer headaches and mild nausea. At higher levels unconsciousness, heart failure,
and even death can occur. The following symptoms are related to CARBON MONOXIDE POISONING and should be discussed with ALL members of the household:
Mild Exposure: Slight headache, nausea, vomiting, fatigue (often described as
flu-like symptoms).
Medium Exposure: Severe throbbing headache, drowsiness, confusion, fast
heart rate.
Extreme Exposure: Unconsciousness, convulsions, cardio-respiratory failure, death.
Many cases of reported carbon monoxide poisoning indicate that while victims are
aware they are not well, they become so disoriented they are unable to save
themselves by either exiting the building or calling for assistance. Also, young children,
the elderly, and household pets may be the first affected by CO poisoning.
The important factor with any CO poisoning, however, is time. At high levels, CO can
cause death in just minutes. At lower levels, it could take from hours to days of constant CO exposure to have the same life-threatening effect.
The chart below illustrates the symptoms of CO poisoning by concentration of CO and
its effect over time.
Slight headache within 2-3 hours.
Frontal headache within 1-2 hours.
Dizziness, nausea, and convulsions within 45 minutes.
Insensible within 2 hours.
Headache, dizziness, and nausea within 20 minutes.
Death within 2 hours.
Headache, dizziness, and nausea within
5-10 minutes. Death within 30 minutes.
Headache, dizziness, 1-2 minutes.
Death in less than 15 minutes.
Death in less than 3 minutes
1000200 300 400 500 600 700 800 900 1000 1100 1200
Concentration of CO in air (ppm)
Conditions That Can Cause CO Levels to Change.
The following conditions can result in transient CO situations in the home.
1. Excessive spillage or reverse venting of fuel burning appliances caused by
outdoor ambient conditions, such as:
a. Wind direction and/or velocity, including high gusts of wind. Heavy air in the
vent pipes (cold/humid air with extended periods between cycles).
b. Negative pressure differential resulting from the use of exhaust fans.
c. Simultaneous operation of several fuel burning appliances competing for limited
internal air.
d. Vent pipe connections vibrating loose from clothes dryers, furnaces, or
water heaters.
e. Obstruction in the vent pipe or unconventional vent pipe designs which can
amplify the above situations.
2. Extended operation of unvented fuel burning devices (range, oven, fireplace, etc.).
3. Temperature inversions which can trap exhaust gasses near the ground.
4. Car idling in an open or closed attached garage, or near a home.
7
TESTING AND MAINTENANCE
Testing
• Stand-alone units: Test each alarm regularly to be sure it is operating properly.
• Interconnected units: Test each alarm in an interconnected system regularly.
• The Smart Button accurately tests all functions. DO NOT use an open flame to test
this CO alarm. You may ignite and damage the smoke alarm or your home.
• Test alarms weekly and upon returning from vacation or when no one has been in
the household for several days.
IMPORTANT! Refer to “Understanding the Alarm LEDs and Horn Patterns” chart
so you understand how to tell if your alarm is operating properly.
Maintenance and Care
DANGER
ELECTRICAL SHOCK HAZARD. Turn off power at main service panel
by removing fuse or switching appropriate circuit breaker to OFF
position BEFORE cleaning CO alarm or replacing the battery.
Cleaning
IMPORTANT: Do not attempt to remove the cover or clean inside the alarm.
THIS WILL VOID YOUR WARRANTY.
Clean the cover at least once a month using the soft brush or wand attachment to a
vacuum cleaner. Be sure all the vents are free of debris. If necessary, use a damp cloth
to clean residual dirt. Do not use abrasive cleansers or spray the alarm with cleaning
agents or waxes, especially cleaners containing ammonia. These liquids may impair the
performance of sensors. Do not submerge the alarm in water.
Replacing the Battery (Model COE and COE-B)
Replace the battery at least once a year or immediately when the low battery
warning activates. If a replacement battery is not immediately available, push
the Smart Button to silence the Low Battery Warning for approximately 10
hours. If alarm does not silence, replace the battery immediately.
Use only Eveready 522, Duracell MN 1604 or Ultralife U9VL-J batteries! DO NOT
USE ANY OTHER TYPE OF BATTERY. DO NOT USE RECHARGEABLE BATTERIES. Refer to the Installation section if you are not familiar with the proper way
to install a new battery.
WARNING
WARRANTY INFORMATION
5-YEAR LIMITED CO ALARM WARRANTY
Invensys Controls Americas warrants to the original consumer purchaser each new
CO alarm to be free from defects in material and workmanship under normal use
and service for a period of five (5) years from the date of purchase. Invensys
Controls Americas agrees to repair or replace, at its option, any defective CO alarm
provided it is returned with postage prepaid and with proof of purchase date to
Invensys Controls Americas. This warranty does not cover damage resulting from
accident, misuse or abuse or lack of reasonable care of the product. This warranty
is in lieu of all other express warranties, obligations or liabilities. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE LIMITED TO A PERIOD OF FIVE (5) YEARS FROM THE DATE OF PURCHASE
FOR THE CO ALARM. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitations may not apply to you. IN NO CASE SHALL
INVENSYS CONTROLS AMERICAS BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY,
EXPRESS OR IMPLIED, WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS
CAUSED BY ITS NEGLIGENCE OR FAULT. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal rights, and
you may also have other legal rights which vary from state to state. This product
meets all the requirements of U.L. Standard 2034.
Where to send your alarm for service
Not attempt to repair this combination alarm. Doing so will void your
warranty. If the alarm is not operating properly, see “Troubleshooting.” If you must
return an alarm under warranty, send the alarm in a well-padded envelope with
postage prepaid, a note describing the nature of the difficulty, and proof of date of
purchase to:
In U.S.: In Canada:
Invensys Controls Americas Invensys Controls Americas
28C Leigh Fisher Blvd. Service de réparation
El Paso Texas 79906 3505 Laird Road - Unit #14
United States of America Mississauga Ontario L5L 5Y7
If the CO alarm is no longer under warranty, have a licensed electrician replace the
CO alarm immediately with a comparable Firex brand alarm.
For Technical Support:
Phone: (800) 445-8299
Email: technicalservice@invensys.com
Website: www.icca.invensys.com/firex
Controls Americas
191 E. North Avenue
Carol Stream Illinois 60188
©2006 Invensys Controls Americas 110-1125C
8
Loading...