Firesense PH08-SA, PH08-SSA User Manual

Patio Heater

Model: PH08-SA, PH08-SSA

Item #: 60804

WARNING: For outdoor use only.

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. If odor continues, immediately call
gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other
flammable vapors or liquids in the
vicinity of this or any other appliance.

An LP-cylinder not connected for
use shall not be stored in the
vicinity of this or any other
appliance.

Instruction Manual & Parts List

INSTALLER: Please leave this manual for the consumer.
CONSUMER: Please retain this manual for future reference.
MANUFACTURER: Changzhou Wellife Furnace Co., Ltd.

- 1 -

FOR YOUR SAFETY

3177588

Tools and parts needed for assembly

DANGER

CARBON MONOXIDE HAZARD

This appliance can produce carbon
monoxide which has no odor.

Using it in an enclosed space can kill you.

Never use this appliance in an enclosed
space such as a camper, tent, car or
home.

WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause injury
or property damage. Read the installation,
operating and maintenance instructions thoroughly
before installing or servicing this equipment.

WARNING :
For Outdoor Use Only

LPG Cylinders to be used must be constructed and
marked in accordance with US DOT specific atio ns.

Storage of the heater indoors is per miss ible only
if the gas cylinder is turned off and re moved .
NOTE:

Use only 20lb LP-Gas tank with size of

18.1in / 46cm(Height)*12.5in / 32cm
(Width).
Do not use if the environment temperature
is below 40 degrees

F / 4.4 degrees C.

- 2 -

Tools needed:

●Open end wrench 10 & 13mm
(included)

NOT included:

●Adjustable opening wrench 8’’
long

●Philips screwdriver w/ medium

blade

●Spray bottle of soapy solution
for leak testing

PRECAUTIONS

NOTE: PLEASE READ THE FOLLOWING SAFETY RULES

WARNING:

This heater must only be used outdoors. Using this product in an enclosed area may
cause injury, death or property damage.

Only use in a well-ventilated space. Do not use in a building, gara ge, or any other
enclosed area.

Read the instructions before use. This heater must be installed in accordance
with local codes or, in the absences of loca l codes, with the Nat ional Fuel Code, ANSI
Z223.1. If applicable, the heater, when installed, must be electrically grounded in
accordance with local codes or, in the absence of l ocal codes, with The National
Electrical Code, ANSI/NFPA70.

Do not use the heat er in an explosiv e atmosphere. Keep t he heater away from areas
where gasoline or other flammable liquids or vapors are stored.

Prior to use, check for damaged parts such as hoses, regulato rs, pilo t o r bu rn er.
Turn off and disconnect LP G c ylin der before moving the heat er.
Do not attempt to alter this heater in any manner. EXAMPLE: Using the heater

without the top canopy reflector or radiant screen.
Do not use this heater in basements or below ground level. It must always be placed

on a solid and level surface.
Always ensure there is ample fresh air ventilation. For outdoor use ONLY.
Never replace or substitute the regulator with any re gulator other than the factory

suggested replacement.
Do not clean the heater with cleaners that are combustible or corrosive.
Do not paint radiant screen, control panel, or top canopy reflect or.
All leak tests should be done with a soapy solution. NEVER USE AN OPEN FLAME TO

CHECK FOR LEAKS.
The LPG cylinder should be turned off when the heater is not in use.
At least once a year, the unit should be inspected for the presence of spiders, spider

webs or other insects.

- 3 -

PRECAUTIONS

CHECK THE HEATER IMMEDIATELY IF ANY OF THE FOLLOWING
EXIST:

1. The smell of gas in conj unction w ith extr eme yellow colored tips of the burner flames.

2. The heater does not reach temperature.

3. The burner makes a popping noise during use (a slight popping noise is normal when
the burner is extinguished after using).

Children and adults should be aware of the hazards of high surface temperature, and

should stay away to avoid burns or clothi n g ignition.
Young children should be carefully supervised when they are in the area of the heater.
Clothing or other flammable material should not be hung from the heater , or placed on

or near the heater.

Any guard or other protective device removed for servicing the heater must be

replaced prior to operating the heater.
Installation and repair should be done by a qualified service person. The heater should

be inspected before use and cleaning may be required at least once a year, or as
necessary. It is imperative that the control compartment, burner and circulating
passageways of the heater are kept clean.

Keep the heater area clear of combustib le mate rials such as ga solin e and o ther f lammable
vapors and liquids.

Do not obstruct the flow of combustion and ventilation air.
Keep the ventilation opening of the LPG cylinder enclosure free and clear of debris.

Storage of a heater indoors is permissible only if the LPG cylinder is turned off,
disconnected and removed from the heater.
Cylinders must be stored outdoors in a well-ventilated area out of the reach of
children. Disconnected cylinders must have threaded valve plugs tightly installed,
and must not be stored in a building, garage or any other enclosed area.

。

- 4 -

ASSEMBLY

# 13 (exploded view)

1. Base assembly with
tank and control
housing

2. 2pcs wheels

3. Handle

4. 2pcs glass tube fixed
parts (one for top, one
for bottom)

5. 2pcs glass tube

6. Glass tube connector

7. 4pcs lower support

8. 4pcs upper support

9. 4pcs support connector

10. 8pcs mesh guard

11. Upper plate

12. Top reflector

13. 4pcs mesh fixed parts
(see exploded view
below)

14. 3pcs gas cylinder fixed
parts and 3pcs
M8x25mm bolts (to
secure LPG cylinder on
base)

15. 4pcs M12 screws

16. 4pcs M5x10mm bolts

17. 4pcs M6x12mm bolts

18. 6pcs M6x12mm bolts

19. 3pcs 3/16’’ screws

20. 3pcs M4x8mm screws

21. 3pcs M4x8mm screws

22. 4pcs M4x8mm screws

23. 8pcs M6x18mm bolts

24. 8pcs M6 nuts

- 5 -

ASSEMBLY

WARNING: This appliance requires installation by a competent

person. Proper assembly is the responsibility of the installer.

Step 1

Attach the wheels (2) to the base assembly
(1)with 8pcs M6x18mm bolts (23) and
8pcs M6 nuts (24).

Step 2

Attach the handle (3) to the back
panel of the base assembly(1) with
4pcs M6x12mm bolts (17).

- 6 -

ASSEMBLY

Step 3

Attach one of the glass tube fixed
parts (4) on the base assembly (1)
with 3pcs M4x8mm screws (20).

Step 4

Screw the 4pcs lower support (7)
into the holes located on the top
of the base assembly (1).

- 7 -