Fire Sense PH01-S, PH01-SS Instruction Manual & Parts List

- 1 -

Patio Heater

Model: PH01-S PH01-SS
Item numbers: 61185

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. If odor continues, immediately
call gas supplier.

PLEASE retain this manual for
reference

.

FOR YOUR SAFETY

Do not store or use gasoline or
other flammable vapors or liquids
in the vicinity of this or any other
a

ppliance.

Instruction Manual & Parts List

INSTALLER: Please leave this manual for the consumer.
CONSUMER: Please retain this manual for future reference.
Manufacturer: Changzhou Wellife Furnace Co., Ltd.

WARNING: For outdoor use only.

CERTIFICATE TO
ANSI 83.26a-2008
CONFORM TO CSA

2.37a-2008

Intertek

DANGER

CARBON MONOXIDE HAZARD

This appliance can produce carbon monoxide

which has no odor.

Using it in an enclosed space can kill you.

Never use this appliance in an enclosed space

such as a camper, tent, car or home.

WARNING :

For Outdoor Use Only

LPG Cylinders to be used must be constructed and
marked in accordance with US DOT specifications.

Storage of the heater indoors is permissible only
if the gas cylinder is turned off and removed.
NOTE:
Use only 20lb LP-Gas tank with size of 18.1in
/ 46cm(Height)*12.5in / 32cm (Width).
Do not use if the environment temperature is
below 40 degrees F / 4.4 degrees C.

WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause injury
or property damage. Read the installation,
operating and maintenance instructions thoroughly
before installing or servicing this equipment.

Tools needed:

● Open end wrench 10 &

13mm (included)

NOT included:

● Adjustable opening wrench

8’’ long

● Philips screwdriver

w/ medium blade

● Spray bottle of soapy

solution for leak testing

Tools and parts needed for assembly

- 2 -

NOTE: PLEASE READ THE FOLLOWING SAFETY RULES

WARNING:

PRECAUTIONS

This heater must only be used outdoors. Using this product in an enclosed area may
cause injury, death or property damage.

Only use in a well-ventilated space. Do not use in a building, garage, or any other
enclosed area.

Read the instructions before use. This heater must be installed in accordance
with local codes or, in the absences of local codes, with the National Fuel Code, ANSI
Z223.1. If applicable, the heater, when installed, must be electrically grounded in
accordance with local codes or, in the absence of local codes, with The National
Electrical Code, ANSI/NFPA70.

Do not use the heater in an explosive atmosphere. Keep the heater away from areas
where gasoline or other flammable liquids or vapors are stored.

Prior to use, check for damaged parts such as hoses, regulators, pilot or burner .
Turn off and disconnect LPG cylinder before moving the heater.
Do not attempt to alter this heater in any manner. EXAMPLE: Using the heater without

the top canopy reflector or radiant screen.

Do not shorten the burner post assembly.
Do not use this heater in basements or below ground level. It must always be placed on

a solid and level surface.
Always ensure there is ample fresh air ventilation. For outdoor use ONLY.
Never replace or substitute the regulator with any regulator other than the factory

suggested replacement.
Do not clean the heater with cleaners that are combustible or corrosive.
Do not paint radiant screen, control panel, or top canopy reflector.
All leak tests should be done with a soapy solution. NEVER USE AN OPEN FLAME TO

CHECK FOR LEAKS.
The LPG cylinder should be turned off when the heater is not in use.
At least once a year, the unit should be inspected for the presence of spiders, spider

webs or other insects.

- 3 -

be replaced prior to operating the heater.

Young children should be carefully superv

CHECK THE HEATER IMMEDIATELY IF ANY OF THE FOLLOWING
EXIST:

1. The smell of gas in conjunction with extreme yellow colored tips of the burner flames.

2. The heater does not reach temperature.

3. The burner makes a popping noise during use (a slight popping noise is normal
when the burner is extinguished after using).

Children and adults should be aware of the hazards of high surface temperature,
and should stay away to avoid burns or clothing ignition.

ised when they are in the area of the heater.

Clothing or other flammable material should not be hung from the heater, or placed

on or near the heater.

Any guard or other protective device removed for servicing the heater must

Installation and repair should be done by a qualified service person. The heater should
be inspected before use and cleaning may be required at least once a year, or as
necessary. It is imperative that the control compartment, burner and circulating
passageways of the heater are kept clean.

Keep the heater area clear of combustible materials such as gasoline and other
flammable vapors and liquids.

Do not obstruct the flow of combustion and ventilation air.

Keep the ventilation opening of the LPG cylinder enclosure free and clear of debris.
Storage of a heater indoors is permissible only if the LPG cylinder is turned
off, disconnected and removed from the heater.
Cylinders must be stored outdoors in a well-ventilated area out of the reach
of children. Disconnected cylinders must have threaded valve plugs tightly
installed, and must not be stored in a building, garage or any other enclosed
area.

PRECAUTIONS

- 4 -

ASSEMBLY

1. 3 pcs castle nuts

2. Reflector

3. 6 pcs 8mm washers for pins
support

4. 3 pcs 90mm (L) pins for
reflector support

5. Head assembly

6. 4 pcs M6x10mm bolts

7. 2 pcs Post assembly

8. Tank housing

9. Regulator

10. 6 pcs M6x30mm bolts and
M6 washers and 6mm nuts

for connection of

post support

and support

legs

11. 3 pcs M8x16mm bolts for
connection of support

legs and base

12. Post support

13. 6pcs M6x12mm bolts and

M6 washers and 6mm nuts for
connection LPG cylinder fixed

parts with base,6pcs M8x25mm
bolts for securing the cylinder

14. 3 pcs Support legs

15. Base

16. 1 pc open end wrench

(10&13mm)

17.

18.

19.Empty water box(attached to base -

fill with sand before use)

Wheel assembly
Gas hose
(attached to head assembly)

17

- 5 -

19

ATTACHING WHEEL ASSEMBLY

Step 1
1-1. Locate Wheel Assembly (17) and 2 nuts/bolts

contained in plastic bag with Wheel Assembly
(Fig. 1).

Step 2
2-1. Turn Base (15) so that holes for attachment of

Wheel Assembly are facing you (Fig. 2).

2-2. Align holes in Wheel Assembly (17) with
holes on Base (15) (Fig. 3).Insert bolts through both sets of holes
and secure nuts on end of bolt (Fig. 4).

Step 3
3-1. Wheel Assembly (17) should now be attached to Base (15)

as shown (Fig. 5).

ASSEMBLY

Fig. 1

Fig. 2

Fig. 3 Fig. 4

Fig. 5

- 6 -