Fire Magic E790S4EAP62W Quick Guide
Outdoor Stand Alone
U
L
Gas Grill
ECHELON
Quick Start Guide
diamond “A” series
CAUTION: For your safety read the installation instructions and owner’s manual provided with the grill.
1-Safety
INSTALLER: Leave these instructions with consumer. CONSUMER: Retain for future reference.
This grill must be installed in accordance with local codes and ordinances, or, in the absence of local codes, with either the latest National Fuel Gas Code (ANSI
Z223.1/NFPA 54), and Natural Gas and Propane Storage and Handling Installation Code (CSA-B149.1).
This appliance and its individual shutoff valves must be disconnected from the gas-supply piping system when testing the system at pressures in excess of ½ psig.
This appliance must be isolated from the gas-supply piping system by closing its dedicated manual shutoff valve during any pressure testing of the gas-supply
system at pressures up to and including ½ psig.
WHEN INSTALLING AND OPERATING THIS APPLIANCE WITH PROPANE (L.P.) GAS, ALL INSTRUCTIONS AND WARNINGS IN YOUR OWNER’S MANUAL
MUST BE OBSERVED. FAILURE TO DO SO MAY RESULT IN A FIRE OR EXPLOSION CAUSING SERIOUS INJURY OR DEATH.
This grill is designed for outdoor use only. DO NOT use this grill inside a building, garage, enclosed area, or under any overhead construction. DO NOT
use this grill in or on a recreational vehicle or boat.
Installation must be performed by a qualifi ed professional service technician.
2-Unpacking
Carefully unpack the grill, removing all packing material and protective fi lm. Verify that all
parts have arrived undamaged by consulting the parts list in the owner’s manual. Remove
foam packed hardware from oven area. (See Fig. 2-1.)
Consult the parts list in the owner’s manual. If any parts are missing or damaged,
immediately contact the Fire Magic dealer before beginning installation.
Important: The 2 shipping screws must be removed prior to removing the unit from
the wooden pallet. The screw located on the bottom left side of the unit is
accessed by opening the door. The screw located on the bottom right side of
the unit is accessed by removing the lower drawer.
To remove the drawer; pull it completely out. Release the drawer from the
drawer slides by pressing the black lever down on the right side, and up on
the left side.
Remove plastic
zip-ties
Lift out foam packed hardware
Fig. 2-1
3-Installation
Location
Locate the grill on a flat level surface. Refer to the INSTALLATION
REQUIREMENTS section of your grill owner’s manual for complete details.
CAUTION: Wind blowing into or across the rear oven lid vent (Fig.
3-1) can cause poor performance and/or dangerous
overheating. Orient the grill so that the prevailing wind
blows toward the front of the grill (Fig. 3-2).
CAUTION: To prevent dangerous overheating, the rear of the unit must have
a minimum clearance of 4” from any non-combustible wall.
Connect Gas supply
These quick start instructions assume a
propane cylinder confi gured unit. See main
instructions for natural gas or household
propane confi gured units.
Place approved propane 20lb cylinder in tank
tray and lock holder in position (Fig. 3-3).
Connect quick coupler hose and regulator
supplied with unit to propane cylinder (Fig.
3-4).
Set all burner control valves to OFF and
open gas source control valve.
Follow the lighting instructions on the
reverse side of this guide.
Proper grill airfl ow must be maintained as
shown in Fig. 3-5.
REV 1 - 1602081000
Sideburner
shelf (if
equipped)
Tool holder
Quick
coupler
Fig. 3-3
Tank tray latch
INCORRECT
Rear oven lid vent
YOU MUST PROTECT REAR OVEN
VENT FROM PREVAILING WIND
Fig. 3-1
Regulator
Backburner
cover (if
equipped)
Paper towel
holder
Propane
cylinder (tank)
Vent
Hose
Fig. 3-4 Type I Acme thread quick coupler
Ventilation diagram
Fig. 3-5
Hand nut with
Acme thread
CORRECT
PLACE GRILL SO PREVAILING WIND
BLOWS TOWARD FRONT OF GRILL
Fig. 3-2
Brass Acme
thread fi tting
Liquid level
indicator
(optional)
To connect the regulator/
hose assembly to the
propane-gas cylinder valve
fi tting: Press the hand nut
on the regulator over the
Acme thread fi tting on the
cylinder valve. Turn the hand
nut clockwise to engage the
threads and tighten until
snug.
Hand wheel
QCC
Type 1
valve
Pressure
relief
valve
L-C2-407
Note: For infrared burner equipped
grills; see detailed instructions
included in your owner’s manual.
Cooking grid
4-Grill Setup
Parts Placement Checklist
Place the following items according to their position and orientation in
Fig. 4-1:
Backburner
cover
Warming
rack
Sideburner
lid
Drip tray
liners
Drip tray (with
lighting instructions)
Fig. 4-1
Flavor grid
(not with IR)
Cotter
pin
Door
E-burner *
(comes pre-
installed)
Rotisserie
rod storage
ring
Drawers
Flavor grids, cooking grids, heat zone dividers, backburner cover,
warming rack, and meat probe.
Leave pre-installed E-burners in place to maintain proper alignment.
Backburner Cover
Hook the backburner cover over the top of the backburner to protect
the backburner from grease, dust and dirt when it is not in use. Remove
before use.
Warming Rack
The warming rack comes pre-installed. Remove zip ties before use.
Consult the owner’s manual to remove or replace.
Shelf/Sideburner (if equipped)
Align the four (4) holes in the shelf with the four (4) holes in the side of
the cart while aligning and engaging the burner venturi with the orifi ce
(Fig. 4-2). Insert the four (4) screws (provided) into the holes and tighten.
Connect the spark wire to igniter electrode (Fig. 4-2). Open sideburner
lid, set cap on burner, and set grid into shelf.
Igniter
The burner ports
*
electrode
and carry-over slots
must be kept clean to
ensure proper ignition
and operation.
Replacement parts can
be ordered from your
local Fire Magic dealer.
Spark
wire
Venturi
Air shutter
Screws
Orifi ce
Fig. 4-2
Read setting here
Read setting
(OFF position shown)
here
TURN OFF
To Turn OFF
TO
Press
knob in
to turn
Fig. 5-1 - Burner valve control knob
OFF
Gas Flow
Indicator
LOW
To Turn ON
T O TURN ON
LIGHT
HI
HIGH to
Use
LIGHT
HI (high)
to light
For your convenience and safety;
when the control knob is in the
ON position, the gas fl ow indicator
will change from blue to red. (Red
indicates gas fl ow.) See Fig. 5-1.
WHEN OPERATING THIS
APPLIANCE WITH PROPANE, ALL
INSTRUCTIONS AND WARNINGS
MUST BE OBSERVED. FAILURE TO
DO SO MAY RESULT IN A FIRE OR
EXPLOSION CAUSING SERIOUS
INJURY OR DEATH.
The light switch is push button operated,
and is located on the right side of the
control panel (see Fig. 5-2). It controls the
power to all lights.
5-Test
Note: This unit must be connected to 120VAC power for electronic lighting.
1. Open lid(s) or remove cover(s) from burner(s) to be lit.
2. Turn all gas control knob(s) to their OFF position(s).
3. Turn on the gas at its source.
Note: DO NOT turn on more than one valve at a time for either electronic or manual lighting.
4. Depress the desired control knob for 5 seconds, then, while pressing turn it counterclockwise to the
HI LIGHT position. Once the burner lights, release the knob.
CAUTION: If a burner does not light within fi ve (5) seconds of turning on the control knob, depress
the knob and turn it to the OFF position. WAIT FIVE (5) MINUTES before repeating
step 4. If you smell gas, follow the instructions on the cover of the grill owner’s manual.
If the burners still do not light after several attempts, refer to the grill owner’s manual
for manual lighting.
5. Repeat step 4 for each additional burner to be lit.
Left
backburner
control knob
(if equipped)
Left main burner
control knob
Sideburner
control knob
Center left main
burner
control knob
Center right main burner
control knob
Pull-out drip
tray
Smoker drawer
burner control
knob
Smoker
drawer
Right
main burner
control knob
Right backburner
control knob
(if equipped)
Fig. 5-2
Light
switch
6-Propane Safety
Gas Cylinders
IMPORTANT: READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.
READ ALL SAFETY INSTRUCTIONS AND WARNINGS REGARDING THE USE OF PROPANE GAS FOUND IN
YOUR OWNER’S MANUAL.
REV 1 - 1602081000
L-C2-407
Loading...