Fire Magic AOP03 User Manual

DOUBLE SIDEBURNER

Instructions

For Natural or Propane Gas

(Shown without cover in place)

SIDEBURNER BUILT-IN

09-41

INSTALLER: Please leave these instructions with the consumer. CONSUMER: Retain for future reference.

Model # 3281(-2)(P)

WARNINGS AND SAFETY CODES

DANGER:

IF YOU SMELL GAS:

1. Shut off the gas to the appliance.

2. Extinguish any open fl ame.

3. Open lid if equipped.

4. If odor continues, keep away from the
appliance and immediately call your
gas supplier or the fi re department.

CODE AND SUPPLY REQUIREMENTS: This outdoor
gas unit must be installed in accordance with local codes
and ordinances, or, in the absence of local codes, with
the latest National Fuel Gas Code (ANSI Z223.1/NFPA

54), or Natural Gas and Propane Storage and Handling
Installation Code (CSA-B149.1).

All electrical outlets in the vicinity of the unit must
be properly grounded in accordance with local
codes, or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70, or the
Canadian Electrical Code, CSA C22.1, whichever

is applicable.

1. Do not store or use gasoline or other
fl ammable vapors and liquids in the
vicinity of this or any other appliance.

2. An LP cylinder not connected for use
shall not be stored in the vicinity of this
or any other appliance.

Improper installation, adjustment, alteration,
service, or maintenance can cause injury or
property damage. For proper installation, refer
to the installation instructions. For assistance
or additional information, consult a qualifi ed
professional installer, service agency, or the

Certifi ed to: ANSI Z21.58-2007
CSA 1.6-2007

Keep all electrical supply cords and fuel supply
hoses away from any heated surface.

WARNING:

WARNING:

gas supplier.

REV 6 0906230824

Robert H. Peterson Co. • 14724 East Proctor Avenue, • City of Industry, CA 91746

1

L-C2-11109

SÛRETÉ ET CODES D’AVERTISSEMENT

INSTALLATION INSTRUCTIONS ET MANUEL DU PROPRIÉTAIRE

DANS LE CONTRE- DOUBLE SIDEBURNER

DANGER:

SI VOUS SENTEZ LE GAZ :

1. Coupez l’admission de gaz de
I’appariel.

2. Éteindre toute fl amme nue.

3. Ouvrir le couvercle.

4. Si l’odeur persiste, éloignez-vous de
l’appareil et appelez immédiatement
le fournisseur de gaz ou le service
d’incendie.

CONDITIONS DE CODE ET D’APPROVISIONNEMENT:

Ce gril doit être installé selon des codes et des ordonnances
locaux, ou, en l’absence des codes locaux, avec l’un ou l’autre
le plus défunt Code national de gaz de carburant (norme ANSI
Z223.1/NFPA 54), et Stockage de gaz naturel et de propane
et manipulation du code d’installation (CSA-B149.1).

Cet appareil et ses différents robinets d’isolement doivent être
démontés du gaz-fournissent le système siffl ant en examinant
le système aux pressions au-dessus du ½ psig (kPa 3.5).

Cet appareil doit être isolé dans gaz-fournissent le système
siffl ant par fermeture que ses différents robinets d’isolement
manuels pendant tous les essais sous pression du gaz­fournissent le système aux pressions jusques et y compris
le ½ psig (kPa 3.5).

• Ce gril est pour ultilisation à l’extérieur seulement. Si
l’appareil est entreposé à l’intérieur, enlever les bouteilles et
les laisser à l’extérieur.

• Ne pas ranger le gril immédiatement aprés l’avoir utilisé.
le laisser refroidir avant de le déplacer ou de la ranger. Le
non respect de cette mesure de sécurité pourrait entraîner un
incendie causant des dommages à la propriété, des blessures
ou la mort.

• Ne pas utiliser cet appareil sous une surface
combustible.

• Ne pas utiliser cet appareil sous un auvent. Le non respect
de cette mesure de sécurité pourrait entraîner un incendie ou
des blessures.

• Dégagement minimal entre les parois latérales et l’arriére
de l’appareil et la construction combustible (45.7 cm à partir
des parois latérales et 45.7cm à partir de l’arriére).

• Le régulareur de pression de gaz prévu avec cet appareil
de cuisson à gaz pour l’extérieur doit être utilisé. Ce régulateur
est réglé pour une pression de sortie de 5 pouces de colonne
de l’eau pour le gaz naturel, et 10 pouces pour le propane.

• LE RÉGULATEUR INCLUS D’APPAREILS EST ÉVALUÉ
POUR LE MAXIMUM DE 1/2 (LIVRES PAR POUCE CARRÉ).
SI VOTRE OFFRE DE GAZ EST 1/2 PLUS GRAND QUE
(LIVRES PAR POUCE CARRÉ), UN RÉGULATEUR
ADDITIONNEL DOIT ÊTRE INSTALLÉ AVANT LE GRIL. VOIR
LA SECTION DE CONDITIONS D’OFFRE DE GAZ POUR

AVERTISSEMENT:

1. Ne stockez pas ou n’employez pas
l’essence ou d’autres vapeurs et liquides
infl ammables à proximité de ceci ou
d’aucun autre appareil.

2. Un cylindre de propane non relié pour
l’usage ne sera pas stocké à proximité
de ceci ou d’aucun autre appareil.

AVERTISSEMENT:

L’installation inexacte, l’ajustement,
le changement, le service, ou l’entretien
peuvent causer des dommages ou des dégats
matériels. Référez-vous à ce manuel. Pour
l’aide ou l’information additionnelle, consultez
un installateur professionnel qualifi é, l’agence

de service, ou le fournisseur de gaz.

Toutes les sorties électriques à proximité du gril doivent être
correctement fondues selon des codes locaux, ou en l’absence
de local code, avec le code électrique national, ANSI/NFPA
70, ou le code électrique canadien, CSA C22.1, celui qui est
applicable.

Maintenez tout électrique-fournissent des cordes et carburant­fournissent des tuyaux partis de n’importe quelle surface de
chauffage.

LA PRESSION APPROPRIÉE D’OFFRE DE GAZ.

• Ne couvrez jamais la surface entière de cuisine ou de gril
de gauffreuses ou de casseroles. La surchauffe se produira et
les brûleurs ne seront pas très performants quand la chaleur
de combustion est emprisonnée au-dessous de la surface à
cuire.

• Ne pulvérisez jamais l’eau sur une unité chaude de gaz,
comme ceci peut endommager des composants de porcelaine
ou de fer de fonte.

• Une fuite de GPL peut causer une incendie ou une
explosion si enfl ammée entraînant des blessures corporelles
graves ou la mort.

• Communiquez avec le fournisseur de GPL pour les
réparations ou pour disposer de qules bouteille ou du GPL
non utilisé.

Certifi é à la norme: ANSI Z21.58-2007
CSA 1.6-2007

INSTALLATEUR : Laissez ces instructions avec le consommateur.

CONSOMMATEUR : Maintenez pour la future référence.

REV 6 0906230824

2

L-C2-11109

DOUBLE SIDEBURNER PARTS LIST

Item Description

Item Description

1. STAINLESS STEEL COVER

1. STAINLESS STEEL COVER

2A. GRID, STAINLESS STEEL

2A. GRID, STAINLESS STEEL

2B. GRID, PORCELAIN CAST IRON

2B. GRID, PORCELAIN CAST IRON

3. BURNER ASSEMBLY

3. BURNER ASSEMBLY

4. VALVE MANIFOLD ASSEMBLY

4. VALVE MANIFOLD ASSEMBLY

5. KNOBS, FIRE MAGIC (2)

5. KNOBS, FIRE MAGIC (2)

6. CONTROL PANEL, STAINLESS STEEL

6. CONTROL PANEL, STAINLESS STEEL

7. REGULATOR

7. REGULATOR

8. IGNITOR ASSY

8. IGNITOR ASSY

BURNER ASSEMBLY

A. BURNER CAP
B. CERAMIC ELECTRODE
C. BURNER
D. VENTURI TUBE
E. ORIFICE, NAT
or ORIFICE, L.P.

A

E

Fig. 3-1

B

C

D

2B

2B

1

1

2A

2A

3

3

4

4

5

5

6

PRODUCT DATA TABLE

Specifi cation Value

Specifi cation Value

Counter Opening Height* 12"

Counter Opening Height* 12"

Counter Opening Width* 11

Counter Opening Width* 11-

Counter Opening Depth* 22

Counter Opening Depth* 22-

Double Side Burner

Double Side Burner

BTU per burner

BTU per burner

Natural Gas Orifi ce

Natural Gas Orifi ce

Propane Gas Orifi ce

Propane Gas Orifi ce

1

1

/2"

/2"

3

1

/4"

/2"

15,000

15,000

#50

#49

#58

#56

7

7

8

8

Venturi
tube

Orifi ce

Burner - top view

Fig. 3-2

REV 6 0906230824

Table 1 - Product data table

3

L-C2-11109

PREPARING FOR INSTALLATION

WHERE TO INSTALL YOUR

DOUBLE SIDEBURNER

FOR OUTDOOR USE ONLY.

Your double sideburner is designed to complement
your Fire Magic grill. It provides a convenient,
effi cient cooking surface for side dishes that
require bottom heat only.

TOOLS REQUIRED

The double sideburner has been pre-assembled.
You need only a pair of wrenches, pliers, or vice
grips for the gas connection.

CODE AND SUPPLY REQUIREMENTS

This burner must be installed in accordance with
local codes and ordinances, or, in the absence
of local codes, with the National Fuel Gas Code,
ANSI Z223.1.

This appliance and its individual shutoff valve
must be disconnected from the gas supply piping
system when testing the system at pressures in
excess of

The appliance must be isolated from the gas supply
piping system by closing its individual manual shutoff
valve during any pressure testing of the gas supply
system at pressures up to and including
(3.5 kpa).

1

/2 psig (3.5 kpa).

1

/2 psig

Do not install this unit under unprotected
fl ammable surfaces. Do not install or use this
appliance inside a building, garage, or any
other covered area. It must not be used in or
on recreational vehicles or boats.

This is a built-in type unit designed to fi t into open­front enclosures. The control panel of the unit is
removable for gas hookup, servicing, and burner
adjustment. The control panel must be removable
after you install the unit.

INSTALLER NOTE: This unit should be installed
so that it can be removed at a later date if factory
service is required. Any protrusion into the double
sideburner enclosure may prevent the unit from
sliding into place (see GAS SUPPLY PLUMBING
REQUIREMENTS, on page 5).

ENSURING PROPER COMBUSTION AIR AND
COOLING AIR FLOW

You must maintain proper air fl ow for your Fire Magic
double sideburner to perform as it was designed
(Fig. 4-1). If airfl ow is blocked, overheating and poor
combustion will result. Make sure not to block the 1"
front air inlet along the bottom of the control panel
or more than 75% of the support grid surface with
pans or griddles.

ELECTRICAL OUTLETS

Electrical outlets in the vicinity of this appliance

must be properly grounded and GFI equipped.

Important: This unit may be installed into combustible

framing (wood, for instance) provided
there is a minimum of a
between the sides of the unit and any
combustible material. This hanger
requires 1
side and back to support the unit.

Fig. 4-1 Top View

Min. 1/2"

Max. 3/4"
air gap to all
combustible

material

1

/2" of countertop on each

2 1/4"

Hanger

1

/2" airspace

Stainless

steel

hanger

1

2

/4"

Sideburner

Countertop

Edge of
counter

cut-out

Fig. 4-2 Front View

Counter Counter

Sideburner

Maintain air gap all the

way down (back and

side) under countertop

Hanger

REV 6 0906230824

4

L-C2-11109

23 3/4"

12"

12 3/8"

2"

2"

1"

X

HEIGHT

4"

WIDTH

PREPARING FOR INSTALLATION (Cont.)

GAS SUPPLY PLUMBING REQUIREMENTS:

The gas supply pipe connection is to be made
through the fl oor at the rear of the enclosure.
Install the gas line stub at least 2" away from the
side walls and 1" from the back wall, but within 5"
of the back wall, as illustrated by the shaded area
X in Fig. 5-1.

CAUTION: An external valve (with a removable

key) in the gas line is advised for
safety and convenience, particularly
if the unit is accessible to children.

GAS SUPPLY AND MANIFOLD PRESSURES:

For natural gas - normal 7" water column (w.c.),
minimum 3-1/2", maximum 10-1/2". For propane

gas - normal 11" w.c., minimum 8", maximum 13".

INSTALLATION

1. CHECKING FUEL AND PROPER ORIFICES

Your double sideburner has been pre-assembled

Fire Magic units are equipped with orifi ces for

at the factory.

natural gas, unless otherwise indicated. For
use with propane gas, smaller orifi ces must be

1. CHECKING FUEL AND PROPER

installed to avoid hazardous overheating. Please

ORIFICES: Fire Magic units are equipped

refer to Table 1 for the correct orifi ce size. Check

with orifi ces for natural gas, unless otherwise

the orifi ce size by following the instructions

indicated. For use with propane gas, smaller

below. The drill size is stamped on the orifi ce.

orifi ces must be installed to avoid hazardous

If the number is not visible you may have to

overheating. (Please refer to Table 1 for the

remove the orifi ce (as detailed below) to read

correct orifi ce size.)

the number stamped on the side of the orifi ce.

To change or inspect an orifi ce, you need a 5/16"

IF YOU ARE NOT SURE YOU HAVE THE

socket with a spacer (a small piece of tape balled

CORRECT SIDEBURNER ORIFICE SIZE (OR

up, with the sticky side out, works well to hold

WISH TO CHANGE THE ORIFICE), FOLLOW THE

the orifi ce) to prevent the orifi ce from sliding too

STEPS BELOW.

far into, or dropping out of, the socket. The entire
sideburner should be lifted from its enclosure and,

CAUTION: IF THE BURNER HAS BEEN IN USE,

where possible, tilted on its side while the orifi ce is
still installed. Complete the following steps:

a. Remove sideburner lid and lift off cooking

a. Remove sideburner lid and lift off cooking

b. Removing the control knob and face screws

b. Remove the control knobs and screws fi rst,

Important: Prior to removing the face, you must

WAIT UNTIL THE BURNER AND ITS
COMPONENTS ARE COOL TO THE
TOUCH.

grid.

grid.

fi rst, carefully lift away the face.

then carefully lift away the control panel.

slide the battery out of the battery

Important: Prior to fully removing the

bracket located on the right side of

control panel, you must

the face.

disconnect the battery holder
assembly wires that are
located behind the control
panel.

A REGULATOR MUST BE PROVIDED AT THE
BOTTLE OR GAS SOURCE FOR USE WITH
PROPANE GAS.

22 1/2"

12"

Height

11 1/2"

Width

Fig. 5-1

c. Reach up under the burner support and

remove the burner retaining clip (see Fig.

c. Remove the burner cap, and where fi tted,

5-1), located at the rear of the burner pipe.

the venturi tube from the center of the
burner (see Fig. 3-1 & Fig. 3-2).

d. Remove the burner cap and carefully lift

the burner up and out, clearing the ceramic

d. If connected, disconnect the fl ex connector

electrode (see Fig. 5-2), and pulling the

from the double sideburner manifold. This

burner tube away from the orifi ce, located

will enable you to lift out the unit from its

on the end of the orifi ce holder on the left

enclosure, giving ease of access.

side of the unit (see Fig. 5-3).

e. Insert the socket into the center of the

Note: You do not have to lift the burner

Check the number on the side or face of the new
orifi ce to be certain you are correctly converting for
your gas type (see step 1, above, for orifi ce sizes).

burner, unscrew and extract the orifi ce,
taking care not to drop it from inside the

completely out of the unit to access the

socket.

orifi ce.

e. Using a

3

/8" socket, remove orifi ce from the
orifi ce holder (see Fig. 5-3) and check the
number stamped on the orifi ce face.

f. Replace with the new (correct) orifi ce for

your gas type.

g. Replace the unit into the enclosure or shelf

and follow steps a-c in reverse.

h. Re secure the battery into the battery

bracket. Replace the face and control knob.

Fig. 5-1

Fig. 5-2

Important: If converting the gas type, see the

Orifi ce located at

end of orifi ce holder

CHECKING AND CONVERTING
THE REGULATOR section.

Orifi ce holder

Fig. 5-3

REV 6 0906230824

5

L-C2-11109

INSTALLATION (Cont.)

f. If an orifi ce change is necessary, replace

2. CONNECTING THE GAS SUPPLY TO YOUR

the orifi ce with the correct sized one.

FIRE MAGlC DOUBLE SIDEBURNER:

g. Replace the sideburner tube over the orifi ce,

a. The valve manifold has a 1/2" male fl are

aligning the burner over the electrode,

inlet fitting. A 1/2" female flare fitting

taking care not to detach it from the wire.

connector nut is required to hook the gas
supply to the double sideburner.

h. Replace the burner retaining clip (underneath

burner), and burner cap.

b. Use a stainless steel fl ex connector to bring

the gas supply from the gas line stub, or

i. Repeat steps c. through h. for the second

propane gas tank to the double sideburner

burner, then replace the grid and lid.

manifold. A 1/2" x 24" or 36" fl ex connector

Important: If converting the gas type, see the

CAUTION: Use only a C.S.A. listed stainless

2. CONNECTING THE GAS SUPPLY TO YOUR

Note: Pipe joint compound should not be used

is suitable for most installations.

CHECKING AND CONVERTING
THE REGULATOR section before

steel fl ex connector. Do not use

replacing the control panel.

a rubber hose or plastic hose

i. Replace the control panel, being sure to

reconnect the battery holder assembly
wires. Replace the control knobs.

within the enclosure for your
sideburner, it will leak, resulting
in an explosion and/or serious
injury.

c. Be sure the gas supply is OFF. Connect

FIRE MAGlC SINGLE SIDEBURNER

the pipe adapter fi tting supplied with the

a. The burner manifold has a

fl ex connector to the gas supply stub. Use

fi tting gas inlet elbow. A 1/2" female fl are

pipe joint compound that is resistant to all

fi tting connector nut is required to hook the

gasses on the pipe fi tting. Tighten fi tting

gas supply to the burner.

to the gas supply and connector fl are nut

b. Use a stainless steel fl ex connector to bring

securely.

1

/2" male fl are

the gas supply from the gas line stub or
propane gas tank to the single sideburner

on fl are fi tting connections.

manifold. A

1

/2" x 24" or 36" fl ex connector

is suitable for most installations.

CAUTION: Use only a C.S.A. listed stainless

steel flex connector. Do not use
a rubber hose or plastic hose

d. Slide the unit into the enclosure.
e. Connect the fl ex connector fl are nut to

c. Be sure the gas supply is OFF. Connect the

f. Check all gas connections for leaks with

Note: Pipe joint compound should not be

3. POSITIONING THE BURNER CAP:
d. Connect the flex connector flare nut to

Place the burner cap so it is centered over
the burner. Ensure that the notches in the
burner cap fi t over the studs protruding from
the burner (see Fig. 6-1).

within the enclosure for your single
sideburner; it will leak, resulting in
an explosion and/or serious injury.

the double sideburner manifold flare
fi tting. Be sure to tighten securely. Use a

pipe adapter fi tting supplied with the fl ex

second wrench to support the fi tting on the

connector to the gas supply stub. Use pipe

manifold to avoid damaging the manifold.

joint compound that is resistant to all gasses
on the pipe fi tting. Tighten fi tting to the gas

a brush and soapy water solution before

supply and connector fl are nut securely.

lighting. NEVER USE A MATCH OR

OPEN FLAME TO TEST FOR LEAKS.

used on fl are fi tting connections.

the single sideburner manifold elbow fl are
fi tting. Be sure to tighten securely. Use a
second wrench to support the manifold to
avoid damaging the manifold.

e. Check all gas connections for leaks with

a brush and soapy water solution before
lighting. NEVER USE A MATCH OR OPEN

FLAME TO TEST FOR LEAKS.

f. Slide the unit into the enclosure.

3. POSITIONING THE BURNER CAP

Place the burner cap
so it is centered over
the burner. Ensure
that the notches in
the burner cap fi t over

Positioning

the studs protruding
from the burner (see

Fig. 6-1

Fig. 6-1).

SAFETY TIPS FOR USING THE DOUBLE SIDEBURNER

Each time you use your double sideburner, ensure
that:

1. The area around the unit is clear and free from

gasoline and other fl ammable vapors, liquids,
and materials.

2. There is no blockage of air fl ow around the

4. Burner fl ames are burning evenly around the

burner.

3. When using propane gas:
a. The special ventilation openings in the

enclosure are kept free and clear of debris.

Do not operate the burner with the cover
closed.

b. If connected to a propane cylinder, the

The valve, igniter, and burner on your double sideburner have been pre-assembled and tested before
shipping. We suggest you follow and practice these instructions for safe lighting of your double sideburner.

REV 6 0906230824

6

rubber hose attached to the regulator is
carefully inspected before each use.

c. The propane cylinder, regulator, and rubber

hose are installed in a location not subject
to heating above 125° F (51° C).

burner cap with a steady fl ame (mostly blue
with yellow tipping).

L-C2-11109

LIGHTING (IGNITION) INSTRUCTIONS

Read all instructions before lighting, and follow these instructions each time you light the grill.

ELECTRONIC LIGHTING

Note: Electronic lighting requires an installed 9-volt

battery with a good charge.

1. Open lid(s) or remove cover(s) from burner(s) to be lit.

2. Turn all gas control knob(s) to their OFF position(s).

3. Turn on the gas at its source.

Read setting here

Read setting

(OFF position shown)

here

TURN OFF

To Turn OFF

TO

Press
knob in
to turn

Fig. 7-1 - Valve control knob

OFF

LOW

To Turn ON

TO TURN ON

LIGHT

HI

HIGH to

Use

LIGHT

HI (high)
to light

4. Depress the desired control knob, and while pressing
turn it counterclockwise to the HI LIGHT position.
Once the burner lights, release the control knob.

Note: DO NOT
turn on more
than one valve at
a time for either
electronic or
manual lighting.

MANUAL LIGHTING

CAUTION: Always wait fi ve (5) minutes for gas to

clear after any unsuccessful lighting
attempt.

1. Follow steps 1 through 3 (left).

2. Insert either a burning long-barrel butane lighter or

2. Insert either a burning long-barrel butane lighter, a

a burning long-stem match through the cooking grid

burning long-stem match, or a burning match held
opening to the top of the lighting tube. (Fig. 7-2).

by a wire extension holder through the cooking grid
For backburners, hold the flame against the

opening to the burner (Fig. 7-2). Hold the fl ame
perforated material of the backburner.

against the edge of the burner.
For sideburners, hold the fl ame against the burner.

3. While holding the match or lighter fl ame next to the

3. While holding the match or lighter fl ame at the top of

3. While holding the match or lighter fl ame at the top

burner, depress the control knob and while pressing
the lighting tube or next to the burner (backburner

of the lighting tube or next to the burner (sideburner

turn it counterclockwise to the HI LIGHT position.
only), depress the desired control knob and while

and backburner only), depress the desired control

Remove the lighter or match when the burner lights,
pressing turn it counterclockwise to the HI LIGHT

knob and while pressing turn it counterclockwise to

and release the control knob.
position. Remove the lighter or match when the

the HI LIGHT position. Remove the lighter or match

4. If the burner does not light, immediately depress

burner lights, and release the control knob.

when the burner lights, and release the control
the knob and turn the valve to OFF. WAIT FIVE
knob.
(5) MINUTES before repeating steps 2 through 4

4. If the burner does not light, immediately depress

of the MANUAL LIGHTING instructions.
the knob and turn the valve to OFF. WAIT FIVE

(5) MINUTES before repeating steps 2 through 4
of the MANUAL LIGHTING instructions.

CAUTION: If a burner does not light within fi ve (5)

seconds of turning on the control knob,
depress the knob and turn it to the OFF

position. WAIT FIVE (5) MINUTES
before repeating step 4. If you smell
gas, follow the instructions on the cover
of this manual. If the burners still do not
light after several attempts, refer to the

instructions for manual lighting.

5. Repeat step 4 for each additional burner to be lit.

REPLACING IGNITOR BATTERIES

To replace the 9V battery powering the ignitors, pull out the
battery holder located on the outside of the control panel.
Remove the lid. Disconnect the battery from the connector
and replace it connecting the new battery. Replace the lid
and close the drawer (see Fig. 7-3).

WHEN USING A PORTABLE PROPANE TANK

Propane tanks are equipped with a safety shutdown
device that may cause low or no gas pressure/fl ame
at the burners if operating and lighting instructions
are not followed exactly (See important note in the
TROUBLESHOOTING section for more details.)

Lighting

tube

Lighter

Fig. 7-2 - Manual lighting

Fig. 7-2 - Manual lighting

SHUTTING OFF THE GRILL

To shut off the grill, depress each valve control knob
and, and while pressing turn it clockwise to the OFF
position.

Always close the valve from the gas supply after each
use of the grill.

Fig. 7-3

Fig. 7-3

7

ALLUMAGE DES INSTRUCTIONS (D’ALLUMAGE)

Lisez toutes les instructions avant l’allumage, et suivez ces instructions chaque fois vous lumière le gril.

ÉCLAIRAGE ÉLECTRONIQUE

Note: L’éclairage électronique exige une batterie installée

de 9 volts avec une bonne charge.

1. Ouvrez les couvercles ou enlevez les couvertures des brûleurs
pour être Lit.

2. Tournez tous les boutons de commande de gaz à leurs
positions de repos.

3. Allumez le gaz à sa source.

Lisez l’établissement ici

Read setting

(OUTRE de montrer)

here

TURN OFF

OUTRE DE

TO

Enfoncez
le bouton
pour
tourner

Fig. 8-1 - bouton de commande

OFF

LOW

TO TURN ON

LIGHT

HI

SUR

HIGH to

Utilisation

LIGHT

SALUT
(haute)
à la lu­mière

4. Diminuez le bouton de commande désiré, et tout en
pressant le tour il dans le sens contraire des aiguilles d’une
montre dans la position LÉGÈRE de HI. Une fois que le
brûleur s’allume, libérez le bouton de commande.

Note: N’ouvrez
pas plus d’une
valve à la fois
pour l’éclairage
électronique ou
manuel.

ÉCLAIRAGE MANUEL

ATTENTION: Attendez toujours cinq (5) minutes le gaz

pour se dégager après que n’importe quelle
tentative non réussie d’éclairage.

1. Suivez les étapes 1 à 3 (à gauche).

2. Insérez un allumeur brûlant de butane de long-baril, une

2. Passez un allumeur brûlant de butane de long-baril ou

allumette brûlante de long-tige, ou une allumette brûlante

une allumette brûlante de long-tige dans la grille à cuire
tenue par un support de prolongation de fi l par la grille

s’ouvrant au dessus du tube d’éclairage. (Fig. 8-2). Pour
à cuire s’ouvrant au brûleur (fi g. 8-2). Tenez la fl amme

des backburners, tenez la fl amme contre le matériel
contre le bord du brûleur.

perforé du backburner. Pour des sideburners, tenez la
fl amme contre le brûleur.

3. Tout en tenant l’allumette ou la fl amme plus légère à côté

du brûleur, diminuez le bouton de commande et tout en

3. Tout en tenant l’allumette ou la flamme plus légère

pressant le tour il dans le sens contraire des aiguilles

au dessus du tube d’éclairage ou à côté du brûleur
d’une montre dans la position LÉGÈRE de HI. Enlevez

(sideburner et backburner seulement), diminuez le
l’allumeur ou assortissez quand le brûleur s’allume, et

bouton et tout en pressant le tour de commande désirés
libérez le bouton de commande.

il dans le sens contraire des aiguilles d’une montre
dans la position LÉGÈRE de HI. Enlevez l’allumeur ou

4. Si le brûleur ne s’allume pas, enfoncez immédiatement

assortissez quand le brûleur s’allume, et libérez le bouton
le bouton et tournez la valve à AU LOIN. ATTENDEZ

de commande.
CINQ (5) MINUTES avant de répéter les étapes 2 à 4

des instructions manuelles d’éclairage.

4. Si le brûleur ne s’allume pas, enfoncez immédiatement

le bouton et tournez la valve à AU LOIN. ATTENDEZ
CINQ (5) MINUTES avant de répéter les étapes 2 à 4
des instructions manuelles d’éclairage.

ATTENTION : Si un brûleur ne s’allume pas dans cinq

(5) secondes d’allumer le bouton de
commande, enfoncez le bouton et tournez­le à la position de repos. ATTENDEZ CINQ
(5) MINUTES avant de répéter l’étape 4. Si
vous sentez le gaz, suivez les instructions
sur la couverture de ce manuel. Si les
brûleurs ne s’allument toujours pas après
que plusieurs tentatives, se rapportent aux
instructions pour l’éclairage manuel.

5. Répétez l’étape 4 pour que chaque brûleur additionnel soit Lit.

REMPLACEMENT DES BATTERIES D’ALLUMEUR

Pour remplacer la batterie de 9V actionnant les allumeurs,
retirez le support de batterie situé sur l’extérieur du panneau
de commande. Enlevez le couvercle. Démontez la batterie
du connecteur et remplacez-la reliant la nouvelle batterie.
Remplacez le couvercle et fermez le tiroir (voir la fi g. le 8- 3).

EN EMPLOYANT UN RÉSERVOIR DE PROPANE PORTATIF

Des réservoirs de propane sont équipés d’un dispositif
d’arrêt de sûreté qui peut ne pas causer le bas ou aucunes
pression de gaz/fl amme aux brûleurs si le fonctionnement
et l’allumage des instructions ne sont pas suivis exactement
(voir la note importante dans la section de dépannage pour
plus de détails.)

Tube

d’éclairage

Plus léger

Fig. 8-2 - Éclairage manuel

Fig. 8-2 - Éclairage manuel

ARRÊT DU GRIL

Pour couper le gril, diminuez chaque bouton de commande de
valve et, et tout en pressant tour il dans le sens des aiguilles
d’une montre à la position de repos.

Fermez toujours la valve de la fourniture de gaz après chaque
utilisation du gril.

Fig. 8-3

Fig. 8-3

8

U

L

SAFE USE & MAINTENANCE OF PROPANE-GAS CYLINDERS

IMPORTANT FOR YOUR SAFETY

READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.

When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed.

FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION.

CYLINDER/CONNECTOR REQUIREMENTS

a. Propane-gas cylinders, valves, and hoses must be

maintained in good condition and must be replaced if
there is visible damage to either the cylinder or valve. If the
hose is cut or shows excessive abrasion or wear, it must
be replaced before using the gas appliance (see e.).

b. This unit, when used with a cylinder, should be connected

to a standard 5-gallon (20 lb.) propane-gas cylinder
equipped with an OPD (Overfi ll Prevention Device).
The OPD has been required on all cylinders sold since

The use of pliers or a wrench should not be necessary. Only
cylinders marked “propane” may be used.

To disconnect: Turn the hand nut counterclockwise until
detached (Fig. 9-1).

Important: Before using the unit, and after each time the

cylinder is removed and reattached, check
the hose for wear (see a.) and check all
connections for leaks. Turn off the unit valves
and open the main cylinder valve, then check
connections with soapy water. Repair any
leaks before lighting the unit.

October 1,1998, to prevent overfi lling.

c. Cylinder dimensions should be approximately 12" (30.5

cm) in diameter and 18" (45.7 cm) high. Cylinders must
be constructed and marked in accordance with the

Specifi cations for Propane Gas Cylinders of the U.S.
Department of Transportation (D.O.T.) or the National
Standard of Canada, CAN/CSA-B339, Cylinders,
Spheres, and Tubes for Transportation of Dangerous
Goods.

d. The cylinder must include a collar to protect the cylinder

valve, and the cylinder supply system must be arranged
for vapor withdrawal.

e. The pressure regulator and hose assembly used must

e. The pressure regulator and hose assembly (Fig. 9-1)

match the specifi cation for Type I by ANSI Z 21.58-2005/

supplied with this outdoor-cooking gas appliance must

CGA 1.6-2005 (see Fig. 9-1).

be used. Original and replacement pressure regulator
and hose assemblies must be those specifi ed by the
manufacturer for connection with a cylinder connecting
device identifi ed as Type I by the ANSI Z 21.58-2005/CGA

1.6-2005 (see PARTS LIST for ordering information).

f. The propane-gas cylinder valve must be equipped with a

cylinder connection coupling device, described as Type
I in the standard defi ned in paragraph e. above. This
device is commonly described as an Acme thread quick

CAUTION: Always turn the propane cylinder main valve

off after each use, and before moving the unit
and cylinder or disconnecting the coupling.
This valve must remain closed and the
cylinder disconnected while the appliance
is not in use, even though the gas fl ow is
stopped by a safety feature when the coupler
is disconnected.

Carefully inspect the hose assembly each time before the
gas is turned on. A cracked or frayed hose should be replaced
immediately.

If the appliance is stored indoors, the cylinder must be
disconnected and removed.

Cylinders must be stored out of

doors, out of the reach of children, and must not be stored

in a building, garage, or any other enclosed area.

FOR YOUR SAFETY

a. DO NOT store a spare propane-gas cylinder under or

near this appliance.

b. NEVER fi ll the cylinder beyond 80-percent full.
c. IF THE INFORMATION IN a. AND b. IS NOT FOLLOWED

EXACTLY, A FIRE CAUSING DEATH OR SERIOUS
INJURY MAY OCCUR.

coupler.

g. If the propane-gas cylinder comes with a dust plug, place

the dust cap on the cylinder valve outlet whenever the
cylinder is not in use.

QUICK COUPLER OPERATION

To connect the regulator/hose assembly to the propane­gas cylinder valve fi tting: Press the hand nut on the regulator

over the Acme thread fi tting on the cylinder valve. Turn the hand

Pressure
relief
valve

Fig. 9-1 Type I Acme thread quick coupler

QCC
Type 1
valve

Hand wheel

Brass Acme
thread fi tting

Liquid level
indicator
(optional)

Hand nut with Acme
thread

Regulator

Hose

nut clockwise to engage the threads and tighten until snug.

ENCLOSURE REQUIREMENTS

FOR YOUR SAFETY, you must provide the openings listed below for drainage, replacement air, and cross-ventilation
of any storage area exposed to possible leakage from gas connections, the unit, or propane cylinders:

One side of the gas cylinder enclosure left completely open to the outside OR by providing four (4) ventilation
openings. Two (2) openings are to be at the cylinder valve level (approx. 16" [40.6 cm] above the fl oor) and on
opposite walls of the enclosure. Two (2) more openings must be at the fl oor level on opposite sides of the enclosure.
The fl oor-level openings must start at the fl oor and shall extend no higher than 5" (12.7 cm) above the fl oor. Each
opening must have a minimum of 10 sq. in. (64.5 cm
a series of holes, omit the grout from masonry joints, or replace a brick with a hardware cloth screen. If the fl oor
in the cabinet is raised and the space beneath the cabinet is open to the outside, the lower ventilation openings
may be in the fl oor.

Consult your gas supplier for ventilation and regulator requirements when connecting to a household propane supply.

2

) of free area. To achieve the proper ventilation, you may drill

Vent

9

U

L

UTILISATION SÛRE ET ENTRETIEN DES CYLINDRES DE GAZ DE PROPANE

IMPORTANT POUR VOTRE SÛRETÉ

LISEZ ET SUIVEZ TOUS LES AVERTISSEMENTS ÉQUIPÉS DE VOTRE CYLINDRE DE GAZ DE PROPANE.

En actionnant cet appareil avec un cylindre de gaz de propane ON DOIT observer ces instructions et avertissements.

LE MANQUE DE FAIRE AINSI PEUT AVOIR COMME CONSÉQUENCE UNE INCENDIE OU UNE EXPLOSION SÉRIEUSE.

CYLINDRE ET CONDITIONS ET
CARACTÉRISTIQUES DE CONNECTEUR

a. Des cylindres et les valves de gaz de propane doivent être

maintenus en bon état et doivent être remplacés s’il y a
des dommages évidents au cylindre ou à la valve.

b. Ce gril, une fois utilisé avec un cylindre, devrait être relié à

un gallon de la norme 5 (20lb.) cylindre de gaz de propane
équipé d’un OPD (remplissez au-dessus du niveau le
dispositif d’empêchement). L’OPD a été exigé sur tous les
cylindres vendus depuis octobre 1.1998 pour empêcher le
remplissage excessif.

c. Les dimensions de cylindre devraient être approximativement

12"(30.5cm) de diamètre et 18" (45.7cm) hauts. Des
cylindres doivent être construits et marqués selon les
caractéristiques pour des cylindres de gaz de propane du
département des ETATS-UNIS du transport (D.O.T.) ou
le niveau national du Canada, du CAN/CSA-B339, des
cylindres, des sphères et des tubes pour le transport des
marchandises dangereuses.

d. Le cylindre doit inclure un collier pour protéger la valve

de cylindre et le circuit d’alimentation de cylindre doit être
assuré le retrait de vapeur.

e. Le régulateur de pression et l’ensemble de tuyau (

e. Le régulateur de pression et l’ensemble de tuyau utilisé

1

) fourni avec cet appareil à cuire extérieur de gaz doivent

doivent assortir les spécifi cations pour le type I par ANSI

être utilisés. Les régulateurs d’original et de pression de

Z 21.58-2005/CGA 1.6-2005 (voir la fi gue. 10-1).

remplacement et les ensembles de tuyau doivent être ceux

fi g. 10-

indiqués par le fabricant pour le raccordement avec un
dispositif se reliant de cylindre identifi é comme type I par la
norme ANSI Z 21.58-2007/CGA 1.6-2007 avec la norme ANSI
Z 21.58a -1998 d’addenda et CGA 1.6a - M98.

f. La valve de cylindre de gaz de propane doit être équipée

d’un dispositif d’accouplement de raccordement de
cylindre, décrit comme type I dans la norme défi nie dans le
e. de paragraphe ci-dessus. Ce dispositif est généralement
décrit comme coupleur rapide de fi l de point culminant.

g. Si votre cylindre de gaz de propane vient avec une prise

de la poussière, placez le bouchon anti-poussière sur la
sortie de valve de cylindre toutes les fois que le cylindre
n’est pas en service.

OPÉRATION DE COUPLEUR RAPIDE

Pour relier le regulator/hose à l’ajustage de précision de
valve de cylindre de gaz de propane: Serrez l’écrou de main

sur le régulateur au-dessus de l’ajustage de précision de fi l
de point culminant sur la valve de cylindre. Tournez l’écrou de

main dans le sens des aiguilles d’une montre pour engager les
fi ls et pour serrer jusqu’à ce que douillettement. L’utilisation des
pinces ou de la clé ne devrait pas être nécessaire. Seulement
le propane marqué par cylindres doit être employé.

Pour débrancher: Tournez l’écrou de main dans le sens
contraire des aiguilles d’une montre jusqu’à isolé (fi g. 10-1).

Important: Avant d’employer le gril, et ensuite chaque

fois que le cylindre est enlevé et rattaché,
examinez tous les raccordements pour déceler
les fuites. Arrêtez les valves de gril et ouvrez
la valve principale de cylindre, puis vérifi ez
les raccordements avec de l’eau savonneux.
Réparez toutes les fuites avant d’allumer le
gril.

ATTENTION: Tournez toujours la valve principale de cylindre

de propane au loin après chaque utilisation,
et avant de déplacer le gril et le cylindre, ou
débrancher l’accouplement. Cette valve doit
rester fermée et le cylindre a débranché alors
que l’appareil n’est pas en service, quoique
l’écoulement de gaz soit arrêté par un dispositif
de sûreté quand le coupleur est débranché.

Inspectez soigneusement l’ensemble de tuyau chaque fois
avant que le gaz soit allumé. Un tuyau criqué ou frangé devrait
être remplacé immédiatement.

Si l’appareil est stocké à l’intérieur, le cylindre doit être débranché
et enlevé. Des cylindres doivent être stockés hors des portes, hors
de l’extension des enfants, et ne doivent pas être stockés dans un

bâtiment, le garage, ou n’importe quel autre secteur inclus.

POUR VOTRE SÛRETÉ

a. Ne stockez pas un cylindre de gaz disponible de propane

dessous ou ne vous approchez pas de cet appareil.

b. Ne remplissez jamais cylindre au delà de 80 pour cent de

plein.

c. SI L’INFORMATION DANS “A” ET “B” N’EST PAS SUIVIE

EXACTEMENT, UN FEU CAUSANT LA MORT OU DES
DOMMAGES SÉRIEUX PEUT SE PRODUIRE.

Fig. 10-1 type coupleur rapide de fi l de point culminant d’I

Volant de commande

QCC
Type 1

Valve

Valve
de
décompression

1

Ajustage de précision
en laiton de fi l de
point culminant

4

Indicateur
de niveau
de liquide
(facultatif)

3

2

Écrou de main avec le
fi l de point culminant.

Régulateur

Passage

Tuy au

CONDITIONS DE CLÔTURE

POUR VOTRE SÛRETÉ, vous devez fournir les ouvertures suivantes ci-dessous pour le drainage, l’air de rechange, et
la ventilation en travers de n’importe quelle zone de stockage exposée à la fuite possible des raccordements de gaz,
du gril, ou du cylindre de propane:

Un côté de la clôture de cylindre de gaz a laissé complètement ouvert de extérieur OU en fournissant quatre (4)
ouvertures de ventilation. Deux ouvertures doivent être au niveau de valve de cylindre (approximativement 16" (40.6
centimètres) au-dessus du plancher) et sur les murs opposés de la clôture. Deux ouvertures supplémentaires doivent
être au niveau de plancher des côtés opposés de la clôture. Les ouvertures de niveau de plancher doivent commencer
au plancher et se prolongeront pas plus haut que 5"(12.7 centimètre) au-dessus du plancher. Chaque ouverture doit
avoir un minimum de 10 pouces carrés (64.5 cm
forer une série de trous, omettez le coulis des joints de maçonnerie, ou remplacez une brique avec un écran de tissu
de matériel. Si le plancher dans le coffret est augmenté et l’espace sous le coffret est ouvert d’extérieur, les ouvertures

2

) du secteur libre. Pour réaliser la ventilation appropriée, vous pouvez

inférieures de ventilation peuvent être dans le plancher.

10

CARE & CLEANING

CARE AND CLEANING

To enjoy continuous service from your appliance
and to maintain the appearance, we recommend
the following:

Clean your appliance by fi rst using Fire Magic
Barbecue and Grill Cleaner (part #3580-1) to
remove grease and dirt. Always wipe with the grain
(See Fig. 11-1). Next, use Fire Magic Stainless
Steel Cleaner (3581-1) to restore the stainless steel
color (Note: not for mirror fi nish). Finish by wiping
your appliance down using Fire Magic Polish Wipes
(3586-1). To clean the mirror panel, use a quality
brand glass cleaner only, not any of the cleaners
mentioned above.

Clean your appliance at least once a month.
If your appliance is installed in a seaside (salt air) or

poolside (chlorine) location, it will be more susceptible
to corrosion and must be maintained/cleaned more
frequently. Do not store chemicals (such as chlorine
or fertilizer) near your stainless steel appliance.

Due to the nature of stainless steel, surface iron
oxide deposits may appear. Do not be alarmed –
these deposits are removable with stainless-steel
cleaner through prompt and periodic maintenance.
If not attended to promptly, permanent pitting may
occur.

Wipe with grain

Fig. 11-1 - Wipe with grain

PROTECTING YOUR APPLIANCE FROM THE
WEATHER

An optional heavy-duty cover will protect your
appliance’s fi nish and protect your investment. The
water repellent cover will protect your appliance
from the weather. Always cover your appliance
when not in use. (Allow to cool before covering.)

Please specify the model number and serial
number of your appliance when ordering a cover.

Check and clean the burner ports and burner carry­over slits for blockage at least annually by removing
the burner (see orifi ce changing instructions) and
visually inspecting the burner inlet for insects and
nests. A clogged burner can lead to a fi re in the
bottom of the appliance.

The inside of the appliance may be cleaned
periodically with oven cleaner if desired. Follow the
oven cleaner instructions for proper use.

Be careful not to get oven cleaner on the outside
surface of the appliance as it can permanently
damage the fi nish.

By following these recommendations, you will enjoy
the beauty and convenience of your appliance for
many years to come.

11

CHECKING AND CONVERTING GAS TYPE

This unit comes from the factory confi gured for
one type of gas, as marked on the label behind the
faceplate.

Converting this unit to burn a different type of
gas requires a conversion kit from the factory.
The professional installer who converts this
unit to burn a different gas must perform the
following functions:

1. Change brass gas orifices (included at original

shipping) on each burner to match the new gas type
(see PRODUCT DATA TABLE, Table 1).

2. Switch the convertible gas regulator (included

at original shipping) to match the new gas type
(see below).

3. Plumb the unit to the new gas supply.

4. Apply a new label behind the faceplate, indicating

the new gas the unit will burn (included with
conversion kit).

WARNING

HAZARDOUS OVERHEATING WILL OCCUR
IF A NATURAL-GAS ORIFICE IS USED WITH
PROPANE GAS. IF YOU ARE NOT SURE IF THE
CORRECT ORIFICES ARE INSTALLED, OR IF AN
ORIFICE CHANGE IS NECESSARY, REFER TO
THE FOLLOWING INSTRUCTIONS.

CAUTION: Make sure the unit is at a safe

temperature and isolated from gas and
electrical supplies before beginning
the tasks outlined below.

Note: The cooler the unit, the greater the tolerances

between the stainless-steel parts, and
therefore the easier to disassemble and
reassemble parts of the unit.

CAUTION: For your safety, exercise caution and

use adequate hand protection (such
as gloves) when handling potentially
sharp sheet-metal parts.

Regulator: note the cap
on top

STEP 1:

Unscrew and remove the cap from the
regulator, extracting the converter.

CHECKING AND CONVERTING THE REGULATOR

Note: Each end of the plastic converter is engraved with either the letters “NAT”

or “L.P.” (propane) for the respective gasses. When the converter is in the
cap and the cap is held uppermost, the letters seen indicate the gas that
the regulator is set up for.

To convert the regulator from one gas to another, follow steps 1-4.

STEP 3:

Turn the converter around and
replace it carefully, into the
center of the cap (it will snap

Read gas
type here

STEP 2:

Remove the converter (the
plastic stalk) by carefully
pulling it away from the center
of the cap (it will snap out of
its seating).

into place). Check that you can
read the type of gas the unit is
set for.

STEP 4:

Replace the unit into the
regulator and screw down
until snug.

WARNING

THIS APPLIANCE REGULATOR IS RATED FOR 1/2 PSI MAXIMUM. IF YOUR GAS SUPPLY IS
GREATER THAN 1/2 PSI, AN ADDITIONAL REGULATOR MUST BE INSTALLED TO REDUCE
THE INPUT PRESSURE TO THE UNIT to
SECTION FOR PROPER GAS-SUPPLY PRESSURE.

1

/2 PSI OR LESS. SEE GAS-SUPPLY REQUIREMENTS

12

REPLACING THE IGNITOR BATTERY

To replace the 9V battery powering the ignitors, pull out the
battery holder located on the outside of the control panel.

Fig. 13-1

It may be necessary to lift the drawer up slightly before it
will pull out. Disconnect the battery from the connector and
replace it connecting the new battery and closing the drawer
(see Fig. 13-1).

TROUBLESHOOTING

If you have trouble with the unit, please use this list to identify the problem. By trying one or more of the
solutions to the possible cause, you should be able to solve the problem. If this list does not cover your
present problem, or if you have other technical diffi culties with the unit, please contact your local dealer.

PROBLEM POSSIBLE CAUSE CORRECTION

Ignition system
failure

Insuffi cient heat

Uneven heating

Burner goes out on

LOW

Rotisserie noisy

1) Improper air shutter adjustment 1) Adjust air shutters.

2) Ignition wire disconnected 2) Replug wires into generator.

3) Low gas pressure 3) Adjust or replace battery.

4) Dead battery 4) Replace battery.

5) Improper air shutter adjustment 5) Adjust air shutters.

6) Using propane orifi ce for natural gas 6) Change orifi ces.

7) Low gas pressure/fl ame (natural) 7) Have gas company check the
operating pressure at the unit.

8) Low gas pressure/flame

(propane)

9) Burner ports partially blocked by debris 9) Remove burners and clean out ports.

10) Small spiders or insects in burner 10) Inspect burners for spider webs or

11) V a l v e “ L o w ” setting needs

adjustment

12) Rotisserie out of balance 12) Adjust counterbalance.

8) Refill propane tank, or reset
propane tank safety*: Shut off all
valves (including propane tank) and
follow lighting instructions exactly.

other debris that may block gas fl ow.

11) Light burner on HIGH, immediately
turn to LOW setting. Remove
knob from valve and using a small
flat screwdriver, slowly turn the
adjustment screw in the stem,
a little at a time (30° to 45°), in
either direction, until the fl ame is
approximately
burner ports.

1

/4” in height from

Note: *Propane tanks are equipped with a safety shutdown device that may cause low or no gas/fl ame at the

burners if operating and lighting instructions are not followed exactly. If you suspect the propane tank safety
shutoff is in effect, shut off all burner control valves and the propane tank valve. Then read and follow
the LIGHTING INSTRUCTIONS exactly. Lighting instructions are located in the owner’s manual. If the
problem persists, continue troubleshooting, or contact your local dealer or distributor for assistance.

13

FIRE MAGIC® OUTDOOR GAS GRILL LIMITED WARRANTY

LIFETIME WARRANTY - Fire Magic® cast stainless-steel burners, stainless-steel rod cooking grids, and stainless-steel housings are

warranted for as long as you own your Fire Magic® grill.
FIFTEEN-YEAR WARRANTY - Fire Magic® cast brass burners, brass valves, backburner assemblies (except ignition parts), and

manifold assemblies are warranted for 15 years from the date of purchase of your Fire Magic

®

THREE-YEAR WARRANTY - Fire Magic
parts) are warranted for three (3) years from the date of purchase of your Fire Magic

Fire Magic
warranted for one (1) year from date of purchase.

This warranty applies to the original purchaser and to single family residential use only. It commences from date of purchase, and is valid only with
proof of purchase.

This warranty does not cover parts becoming defective through misuse, accidental damage, electrical damage, improper handling, storage, and/or
installation. Product must be installed (and gas must be connected) as specifi ed in the instructions or operator’s manual, by a qualifi ed professional
installer. Accessories, parts, valves, remotes, etc., when used must be Peterson Co. product.

This warranty does not apply to rust, corrosion, oxidation, or discoloration, unless the affected component becomes inoperable. It does not cover
labor or labor-related charges.

This warranty specifi cally excludes liability for indirect, incidental, or consequential damages. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above exclusion may not apply to you. This warranty gives you specifi ed legal rights, and you may have
other rights that may vary from state to state.

For additional information regarding this warranty, or to place a warranty claim, contact the R.H. Peterson dealer where the product was purchased.

®

ignition systems (excluding batteries), electronic components (including lights and thermometers), and accessories are

PLEASE KEEP A COPY OF YOUR SALES SLIP FOR PROOF OF PURCHASE

sideburners and all other Fire Magic® grill components (except ignition and electronic

®

grill.

®

grill.

TO REGISTER YOUR PRODUCT ONLINE GO TO: WWW.RHPETERSON.COM,

AND CLICK ON PRODUCT REGISTRATION. THANK YOU FOR YOUR PURCHASE.

ROBERT H. PETERSON CO.

Quality Check Date:___________

Orifi ce # (Main):__________
Orifi ce # (Other):__________ Model #: ___________
Leak Test: ___________ Serial #: ___________
Burn Test: ___________ Air Shutter: ___________
Gas Type: NAT. / PROPANE Inspector: ___________

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

14