• Combustible construction requires insulating liner
• Select Natural or Propane (LP gas)
• Determine total gas consumption for supply line size
• Access required to gas connections and shut o valve
• Plan location of propane tank away from grill and appliances
• Always refer to the installation and operating instructions of your
Fire Magic® grill and/or accessories for installation guidelines &
safety warnings before starting your project
• Always check all gas connections for leaks
• Provide ventilation in island for gas vapors. Allow at least
four ventilation openings (two at oor level and two 16” above oor
10 in² each) at opposing ends/sides
DETAIL 1
TYPICAL
B
Deluxe 11-S30” 25 1/8”
32” Gourmet Charcoal 14-S131 3/4”32 1/2”
26” Gourmet Charcoal 12-S131 3/4”32 1/2”
Grill Hanger Outline
FOR BULL NOSE COUNTER TOP
Allow the grill face to sit flush
when installed.
LOCATION
• Identify outdoor area where grill will be installed
• Determine the utilities needed (gas, water, electricity, drainage etc.)
• Consider element exposure (sun, wind direction*, weather etc.)
MATERIALS
• Foundation- concrete
• Base- brick, stone, stucco, concrete
• Counter top- tile, granite, marble, concrete
1 ¼”
?,_[YHJ\[V\[MVY
7V^LY/VVK653@
COUNTER TOP
X
10”
11”
TOP VIEW
DE TA I L 1
Grill hanger varies in width (2½"-3")
depending on the size & configuration
of the grill.
AVAILABLE WITH RIGHT
DOOR HINGE (-TSR)
SEE NOTE 6
3" clearance required (on
both sides) for access
to battery compartment
when using material that
extends out from island
surface.
AVAILABLE WITH RIGHT
DOOR HINGE (-SR)
3"
Notes
1. There is a hanger on three sides of each grill. You must
allow clearance for the hanger (SEE DETAIL 1).
2. The control panel (face) of the grill is wider than the
cutout width. This conceals the cutout space on the left &
right hand sides.
3. Clearance of 10” on each side of the oven is
recommended for unrestricted operation of lid and
rotisserie and at least 3” at the rear ange for ease of
maintenance and proper operation. (18” from combustible
surroundings on each side and rear is required)
4. See specic model cutout plan for units equipped with
motorized hood.
5. Insulating liners must be used & are available for
combustible surrounds (See page 6).
6. The rotisserie motor on all models is located on the right
side of the grill. Optional Reverse Brackets are available
to mount rotisserie motor on opposite side. ONLY units
ordered with back burner option come with rotisserie kit
and brackets.
3
Page 4
12
CLASSIC DOUBLE DOORS
24½
20
1
34
8
¾
21
3590A & 3590-DR
REFRIGERATOR
53825-T
TRASH CONTAINER
(1) CO canister can be stored in back.
2
Additional 7" clearance needed.
+ Kegerator requires a circular cut-out on
countertop (2" diameter) for Tap.
†The new Cut & Clean Combo can
also be dropped into the 3280
Single Sideburner cutout.
¼
14
14
24
3591
KEGERATOR(¹)
BLENDER
3284A
4
¾
8
8
¾
¼
¾
12
20
3592
ICE MAKER
23920-1T(-S)*
TANK DOOR LOUVERED
w/ PULL OUT TRAY
4
24
37
24
¼
16
8¾
14
½
½
18
23820-S
DUAL DRAWER
CABINET
SINGLE
SIDEBURNER
3280
4
¼
15
14
+
½
25
½
15
½
20
Cut & Clean Combo
53816
STAINLESS
½
14
STEEL SINK
3587
19½
14 ½
½
½
20
18
23918(-S)*
STORAGE DOOR
23920(-S)*
STORAGE DOOR
23920-1(-S)*
STORAGE DOOR
6
24½
½
12
½
½
20
25914(-S)*
DRAWER & L.P
DOOR ASSEMBLY
ALL DIMENSIONS ARE IN INCHES
DELUXE CLASSIC
COUNTERTOP
31-S
12
DELUXE GOURMET
COUNTERTOP
3C-S
14½
16
½
27¾
29
½
14½
20½
23924(-S)*
STORAGE DOOR
24
½
STORAGE DOOR
14
17
½
12
23912(-S)*
20
½
41
½
12
18½
½
REGAL I COUNTERTOP
18
¾
22
12
½
14
34-S
20½
14
17
¾
22
½
CLASSIC CHARCOAL GRILLS
DESCRIPTION
32” Lift-A-Fire
Charcoal 3334
24” Lift-A-Fire
Charcoal 3339
31” Firemaster 3324
24” Firemaster 3329
OPENING REQUIRED
WIDTHDEPTHHEIGHT
32 1/4”19 3/4” 12”
24 3/4”17 3/4”12”
31 1/4”21 1/4”12”
24 1/4”19 1/4” 12”
12”
9 ¼”
8”
53812
PAPER TOWEL HOLDER
ACCESSORIES CUT-OUT DIMENSIONS
23914(-S)*
STORAGE DOOR
23917(-S)*
STORAGE DOOR
(-S) signifies STAINLESS STEEL
w/o(-S) signifies BLACK POWDER COATED
*
Page 5
12
3"
A430 Pedestal Dimensions
A430s-2E1N-P6
26"
50"
57"
56"
25"
Notes
1. There is a hanger on three sides of the cutout (SEE DETAIL 3).
2. The control panel (face) of the accessories is wider than the cutout
width This conceals the cutout space on the left & right hand sides.
3. Clearance of 10” on each side, and 3” at the rear of the oven is
recommended for unrestricted operation of accessories. (18” from
combustible surroundings on each side and rear)
4. Insulating liners must be used and are available for combustible
surrounds. Double Side burner (3281), Single Side burner (3279-1)
and Drop-In Side burner (3280) do not require an insulating liner
(See page 6).
22
17"
SEARING STATION
32874-1 & 3287-1
12
BAR CADDY
1D-S0
12
SINGLE
SIDEBURNER
32794-1 & 3279-1
14
¼
11
½
¾
12
DBL SEARING STATION
32884-1 & 3288-1
POWER BURNER
19 SERIES
12
SIDEBURNER
32814 & 3281
DOUBLE
24.5"
FOR BULL NOSE COUNTER TOP
Allow the grill face to sit flush
when installed.
12
BEVERAGE CENTER
1D-SSA
12
12
24½
14
DETAIL 4
TYPICAL
12
DETAIL 3
TYPICAL
18
19
11
½
¾
Accessory Hanger Outline
DE TA I L 3
COUNTER TOP
TOP VIEW
Accessory hanger varies in width
(2”-2½” ALL AROUND) depending
on the size & configuration of the
accessory.
Door/Drawer
Frame Outline
½
20
23930-S
CLASSIC DOUBLE DOORS
CLASSIC DOUBLE DOORS
W/ DUAL DRAWERS & TANK TRAY
30
23930S-12
¾
22
12
½
30
21
½
20
23830-S
MASONRY DRAWER CABINET
12
13
20
¾
36
DE TA I L 4
Door frame varies in width (1"-2"
ALL AROUND) depending on the
½
23
31
½
5
3" clearance required (on
both sides) for access to
14
battery compartment when
using material that extends
out from island surface.
size & configuration of the door
& drawer.
5
Page 6
B U I L D I NG I N A C O M BU ST I B L E I S L A N D
INSULATING LINER MUST BE USED WHEN INSTALLING IN A COMBUSTIBLE ISLAND
Not used on Double Sideburner (3281), Single Sideburner (3279-1) or Drop-In Sideburner (3280)
GRILL CUT-OUT DIMENSIONS w/ INSULATING LINER
MODEL
Echelon E1060i
Echelon E790i
Echelon E660i
OPENING REQUIRED
WIDTHDEPTHHEIGHT
ABC
55”26”12”
42 1/8”26”12”
36 3/8”26”12”
ECHELONSTANDALONE
C
A
GREEN: Support Hangers
RED: Heat Shield
BLUE: Combustible Material
C
A
Aurora A790i
Aurora A660i
B
Aurora A540i
Aurora A530i
Aurora A430i
Maintain proper clearance to combustible materials.
Notes:
1. A nominal 1/16” gap around the back and sides of the liner is recommended for ease of installation.
2. The counter top material may be placed up to the insulating liner on the back and sides.
3. A minimum of 100 sq. in. in air ventilation is required at cabinet face.
4. Cabinet face may be made of combustible material up to the front ange of the insulating liner.
42 1/8”26”12”
36 3/8”26”12”
36 5/8”22 1/8”12”
30 1/8” 26”12”
30 1/8”22 1/8”12”
AURORASTANDALONE
To install and operate the Fire Magic outdoor gas appliance,
please refer to the Installation and Operating instructions and
safety precautions shipped with the appliance.
ACCESSORY & LEGACY CUT-OUT
DIMENSIONS w/ INSULATING LINER
B
MODEL
Deluxe
Power Burner
Searing Station
OPENING REQUIRED
WIDTHDEPTHHEIGHT
ABC
2819 3/8”12 1/4”
22 5/8”20 3/4”12”
18 3/8”24 3/4”11 5/8”
The information provided is for reference only. Detailed instructions are supplied with the insulation liner, unique to
the model selected. Read those instructions carefully and completely before starting installation of the liner.
6
Page 7
ECHELON STAND ALONE
C
D
A
B
Model #SeriesTop of Face
(A)
E106062/6337"53"86 1/
E106051/7137"77 3/
E79062/6337"40"73 1/
E7907137"58 3/
E66062/6337"34 1/
E6607137"
Cart Base
(B)
4"
4"
4"
53"
Shelves Up
(C)
111"60 1/
92"60 1/
67 1/
86 1/
4"
4"
2"
4"
Oven Open
(D)
60 1/
2"
2"
60 1/
2"
2"
60 1/
2"
60 1/
2"
E
F
Max Outer
(E)
29 3/
4"
29 3/
4"
29 3/
4"
29 3/
4"
29 3/
4"
29 3/
4"
Cart Base
(F)
Oven Closed
(G)
1-Up/1-Down
26"52"74 3/
26"52"99 1/
26"52"61 3/
26"52"80 1/
26"52"56"
26"52"74 3/
I
G
H
4"
2"
4"
2"
4"
Shelves Down
(I)
n/a
88"
n/a
69"
n/a
63 1/
4"
(H)
AURORA STAND ALONE
C
®
D
B
Model #SeriesTop of Face
(A)
A660s61/6237"32 1/
A540s61/6237"32 1/
A530s61/6237"26"55 3/
A430s61/6237"26"55 3/
Cart Base
(B)
2"
2"
A
Shelves Up
(C)
62 1/
62 1/
4"
4"
4"
4"
E
F
Oven Open
(D)
60 1/
2"
57"25 3/
60 1/
2"
57"25 3/
Max Outer
(E)
29 3/
4"
4"
29 3/
4"
4"
I
®
H
Cart Base
(F)
26"52"52 1/
21 3/
26"52"46"35 1/
21 3/
4"
4"
Oven Closed
(G)
1-Up/1-Down
(H)
2"
50"52 1/
2"
50"46"35 1/
Shelves Down
(I)
41 1/
41 1/
G
2"
2"
4"
4"
7
Page 8
V E N T H O O D
SPECIFICATION
36”
42”
60”
∆
~†
*
30”
18”
Electrical
requirements
Fans12 VDC, 1400 CFM
Power supply †12 VDC, 60 watts
110 volts, 60 hertz, 20 amp;
GFI outlet.
Models Available
† 36-VH-4
~ 36-VH-3
∆ 42-VH-3
* 60-VH-3
FIRE MAGIC OUTDOOR GAS GRILL WARRANTY
LI F E TIME WARRA N TY
FIRE MAGIC CAST STAINLESS STEEL BURNERS, STAINLESS STEEL ROD COOKING GRIDS, AND STAINLESS
STEEL HOUSINGS ARE WARRANTED FOR AS LONG AS YOU OWN YOUR FIRE MAGIC GRILL.
FI F T EEN Y E AR WA RRANTY
FIRE MAGIC BRASS BURNERS, BRASS VALVES, MANIFOLD ASSEMBLIES , AND BACKBURNER ASSEMBLIES (EXCEPT
IGNITION SYSTEMS) ARE WARRANTED FOR FIFTEEN (15) YEARS.
TE N YEAR WARRA N TY
FIRE MAGIC ELECTRIC GRILLS, ELECTRIC GRILL STAINLESS STEEL COOKING GRIDS, AND ELECTRIC GRILL STAINLESS
STEEL HOUSING ARE WARRANTED FOR TEN (10) YEARS.
FI V E YEAR WARR A NTY
INFRARED BURNERS, CHARCOAL STAINLESS STEEL GRILLS, AND SMOKERS (EXCEPT FOR THE CHARCOAL PAN,
CHARCOAL GRID, WOOD PELLET SCREEN, THERMOMETER, AND ASH TRAY WHICH ARE WARRANTED FRO ONE YEAR)
ARE WARRANTED FOR FIVE (5) YEARS
TH R E E YEA R WAR R ANTY
FIRE MAGIC SIDEBURNERS AND ALL OTHER FIRE MAGIC GRILL COMPONENTS (EXCEPT IGNITION SYSTEMS AND
ELECTRICAL PARTS) ARE WARRANTED FOR THREE (3) YEARS.
ON E YEAR WARRA N TY
FIRE MAGIC IGNITION SYSTEMS (EXCLUDING BATTERIES), ELECTRICAL COMPONENTS (INCLUDING LIGHTS AND
THERMOMETER), AND GRILL ACCESSORIES ARE WARRANTED FOR ONE (1) YEAR.
THE ROBE RT H. PETER SO N CO®. RE SE RVES THE RI GH T TO AMEN D PRODUCT SPE CIFICATIONS WI THOUT PRIOR N OTICE.
WWW.RHPETERSON.COM PHONE 626.369.5085
L-C1-01312
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.