Fire Magic 54020S, 53812 Specifications Sheet

DOOR, DRAWER, & PANTRY

INSTALL SPECIFICATIONS

Model # 53830SC Shown

Model # 53930SC Shown

GENERAL INFORMATION

WARNING

INSTALLER: Leave these instructions with consumer.

CONSUMER: Retain for future reference.

Important: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION

• When installing this unit directly below another unit, only install with Fire Magic built-in products.

• For proper installation, be sure to use the correct cutout dimensions as specifi ed for your specifi c
model number.

• It is recommended that silicon caulking (not supplied) is applied around the back of the unit’s
trim before sliding the cabinet assembly into the opening.

• Some models may include an additional owner’s manual.

This unit is to be installed by a qualifi ed,

professional service technician.

• When used for propane cylinder storage, a louvered door model is required.

CAUTION: Make sure the enclosure is properly vented. See your grill owner’s manual for venting

requirements, or consult your local codes.

WHEN USING A PROPANE TANK CYLINDER:

• Never locate a cylinder under or near a grill unless suffi cient ventilation and shielding is
provided to prevent any heating of the cylinder regulator and hose. Refer to any additional

instructions included with your door (and/or your grill owner’s manual) for the required installation
method of propane tank cylinders.

• FOLLOW ALL THE SAFETY WARNING AND INFORMATION FOUND IN THESE
INSTRUCTIONS, ON YOUR PROPANE CYLINDER, AND IN YOUR GRILL OWNER’S MANUAL
ABOUT SAFE STORAGE AND USE OF PROPANE GAS.

ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746

REV 4 - 1812041030

1

L-C2-358

INSTALLATION GUIDELINES

For proper installation, be sure to use the correct cutout
dimensions as specifi ed for your model number. Locate
your model on the following pages for dimensions, and
reference the cut-out diagram of your unit for proper
orientation.

Important: Doors and drawers are supplied with 8 screws

for installation. If installing into a concrete
island, pilot holes are required.

Important: When installing in an AFD GFRC Island, use

the bracket and screws provided with the
island.

DOOR

Slide in and fasten the unit securely into the island enclosure
using the supplied hardware through the installation screw slots
or holes in the top and bottom of the unit.

For doors with soft-close hinge:

Soft-close hinges have two door adjustment screws per hinge.
Screw "A" adjusts the door left or right. Turn clockwise to move
right and counterclockwise to move left, on both hinges. See Fig.
2-2. Screw "B" allows for the door to adjust inward or outward.
First loosen screw "B", adjust door as needed, then re-secure.
See Fig. 2-2.

For doors with propane tank trays:

To use, simply open the door, pull out the sliding cylinder tray,
place your cylinder on the tray and push the tray back in. The
cylinder is now ready for connection to your grill.

Important: Refer to any additional instructions included

with your door for the required installation
method of propane tank cylinders.

H
E

I

WIDTH

G
H
T

Fig. 2-1 Door cut-out diagram

Screw B Screw A

Fig. 2-2 Adjust door

Screw A: adjust
left/right

Screw B: adjust
inward/outward

A

B

Fig. 2-3 Adjust door

REV 4 - 1812041030

2

L-C2-358

Drawer
support

Side View

Drawer

front

INSTALLATION GUIDELINES (cont.)

PANTRY

Installation Guidelines

Before installing your pantry, remove the drawer from its
base by completely pulling it out. Release the drawer from
the drawer slides by pressing the black lever down on the
right side, and up on the left side
on the drawer until it comes free of the runners.

1. Slide in and fasten the unit securely into the island
enclosure using the appropriate hardware for your
construction (not supplied) through the installation holes
in the top, sides, and bottom of the unit.

Important: Install using

3

screws are fl ush.

2. To re-attach the drawer; extend the drawer slides
completely and align the drawer into the slides, pushing
the drawer closed. Open the drawer to verify that it has
locked in place.

Note: DO NOT damage gasket while installing the screws.

Inner Drawer Height Adjustment

The top inner-drawer height can be adjusted (lowered) by
raising the drawer runners.

1. Pull out the drawer completely (see above section).

2. From the interior of the drawer, use a fl at head

screwdriver and a hammer to tap the runners free
(through the notches). See Fig. 3-3.

3. Align each runner over the alternate notches and use
the hammer to gently tap into place (see Fig. 3-4).

4. Reinstall the drawer.

DRAWER

Before installing your drawer, remove the drawer from its
base by completely pulling it out. Release the drawer from
the drawer slides by pressing the black lever down on the
right side, and up on the left side
on the drawer until it comes free of the runners.

1. In order to properly support the weight of your drawer, it
is necessary to provide a secure, level surface in the rear
of the unit (see
using bricks, 2 X 4’s, etc. Be sure that the height of this
rear support is 1/8" higher than that of the front opening
support, so that your drawer sits level.

2. Slide in and fasten the unit securely into the island
enclosure using the supplied hardware through the
installation screw slots in the top and bottom of the unit.

3. To re-attach the drawer, extend the drawer slides
completely and align the drawer into the slides, pushing
the drawer closed. Open the drawer to verify that it has
locked in place.

Fig 3-6

(Fig 3-2). Then pull outward

/16" countersink screws. Ensure

(Fig 3-2). Then pull outward

). This may be accomplished by

H

DEPTH

E

I
G
H
T

WIDTH

Fig. 3-1 Pantry cut-out diagram

Fig. 3-2 Releasing drawer from slides

Hammer

through notch

(Interior of

the drawer)

Fig. 3-3 Release tracking from drawer

Fig. 3-4 Reinstall runners

DEPTH

H
E

I
G
H
T

WIDTH

Fig. 3-5 Drawer cut-out diagram

REV 4 - 1812041030

Fig. 3-6 Drawer Installation (Side View)

3

L-C2-358

FLUSH-MOUNTED DOORS, DRAWERS, & PANTRY

Cut-out is height x width x depth

DOUBLE DOORS WITH DUAL DRAWERS
MODEL:
CUT-OUT:

53930SC-22
21” x 30 ½” x 20 ½”

ELECTRIC WARMING DRAWER

MODEL:
CUT

53830-SW

-OUT:

14 ½” x 32 ¼” x 22”

DOUBLE DOORS WITH TRASH
TRAY & DUAL DRAWERS

MODEL:
CUT

TRIPLE ENCLOSED DRAWERS

MODEL:
CUT

53930SC-12

-OUT:

21” x 30 ½” x 20 ½”

53803SC

-OUT:

26 ¼” x 14 ½” x 20 ½”

MASONRY DRAWER

MODEL:
CUT

DOUBLE ENCLOSED DRAWERS

MODEL:
CUT

(53802SC model shown)

53830SC

-OUT:

14 ½” x 32 ¼” x 22”

53802(H)SC

-OUT:

16” x 14 ½” x 20 ½”

SINGLE ACCESS DOOR*

MODEL:
CUT

DOUBLE ACCESS DOORS

MODEL:

-OUT:

CUT

(53938SC model shown)

REV 4 - 1812041030

-OUT:

53924SC-L
25” x 17 ½”

53938(H)SC
16” x 39”

DOUBLE ACCESS DOORS

MODEL:

-OUT:

CUT

SINGLE DOOR WITH DUAL DRAWERS*

MODEL:
CUT

53934SC
15” x 30”

53820SC-R

-OUT:

Available in left or right hinge

*

21” x 14 ½” x 20 ½”

4

ACCESS DOOR W/ DOUBLE
DRAWERS

MODEL:

-OUT:

CUT

SINGLE ENCLOSED DRAWER

MODEL:
CUT

53810SC
18 ½” x 30” x 26”

-OUT:

53801SC
5 ¼” x 14 ½” x 20 ½”

L-C2-358

FLUSH-MOUNTED DOORS, DRAWERS, & PANTRY (cont.)

Cut-out is height x width x depth

DOUBLE ACCESS DOORS

MODEL:
CUT

-OUT:

SINGLE ACCESS DOOR*

MODEL:

-OUT:

CUT

53930SC
21” x 30”

53914SC-R
15” x 20 ½”

SINGLE ACCESS DOOR*

MODEL:
CUT

-OUT:

(53920SC-L model shown)

DOUBLE ACCESS DOORS
WITH LOUVERS

MODEL:

-OUT:

CUT

53920(H)SC-L
21” x 14 ½”

53930SC-1
21” x 30”

SINGLE ACCESS DOOR*

MODEL:
CUT

ACCESS DOORS W/ PLATTER STORAGE
AND DOUBLE DRAWERS

MODEL:
CUT

53816SC

-OUT:

18 ½” x 36½” x 26”

-OUT:

53917SC-R
18” x 24 ½”

PANTRY W/ TOP DRAWER
AND SINGLE DOOR W/ DUAL
DRAWERS (INSULATED)

MODEL:

-OUT:

CUT

REV 4 - 1812041030

54020S
33 ½” x 20” x 26”

Also available: (not shown)

MODEL: 54018S
MODEL: 53820SC-L
MODEL: 53820(H)SC-TL or
MODEL: 53914SC-L
MODEL: 53917SC-L
MODEL: 53920(H)SC-R
MODEL: 53924SC-R
MODEL: 53930SC-12T

TRASH CABINET

MODEL:

-OUT:

CUT

(53820TSC model shown)

Available in left or right hinge

*

53820(H)TSC
21” x 14 ½” x 19 ¼”

CUT-OUT: 25” x 17 ½” x 26”
CUT-OUT: 21” x 14 ½” x 20 ½”
CUT-OUT: 21” x 14 ½” x 20 ½”

TR

CUT-OUT: 15” x 20 ½”
CUT-OUT: 18 ½” x 24 ½”
CUT-OUT: 21” x 14 ½”
CUT-OUT: 25” x 17 ½”
CUT-OUT: 21” x 30 ½” x 20 ½”

5

L-C2-358

SELECT DOORS & DRAWERS

Cut-out is height x width x depth

ELECTRIC WARMING DRAWER

MODEL:

-OUT:

CUT

TRIPLE DRAWERS

MODEL:
CUT

33803

-OUT:

26 ¼” x 14 ½” x 20 ½”

33830-SW
13” x 31” x 20 ½”

MASONRY DRAWER

MODEL:

-OUT:

CUT

DOUBLE DRAWERS

MODEL:

-OUT:

CUT

33802
16” x 14 ½” x 20 ½”

33830-S
13” x 31” x 20 ½”

DOUBLE ACCESS DOORS

MODEL:
CUT

DOUBLE DOORS WITH TANK TRAY
AND LOUVERS

MODEL:

-OUT:

CUT

33930S

-OUT:

21” x 30”

33930S-12T
21” x 30 ½” x 20 ½”

REV 4 - 1812041030

SINGLE DOOR WITH DUAL DRAWERS*

MODEL:

-OUT:

CUT

33820-SR
21” x 14 ½” x 20 ½”

*

Available in left or right hinge

ACCESS DOORS W/ PLATTER STORAGE
AND DOUBLE DRAWERS

MODEL:

-OUT:

CUT

6

33816S
18 ½” x 36½” x 26”

L-C2-358

SELECT DOORS & DRAWERS (cont.)

Cut-out is height x width x depth

SINGLE ACCESS DOOR*

MODEL:
CUT

-OUT:

33914-SR
15” x 20 ½”

SINGLE ACCESS DOOR WITH TANK
TRAY AND LOUVERS*

MODEL:

-OUT:

CUT

DOUBLE DOORS WITH 2 DRAWERS

MODEL:
CUT

33820-TSL
21” x 14 ½” x 20 ½”

-OUT:

33930S-22
21” x 30 ½” x 20 ½”

SINGLE ACCESS DOOR*

MODEL:

-OUT:

CUT

SINGLE ACCESS DOOR*

MODEL:
CUT

-OUT:

33917-SR
18” x 24 ½”

33920-SR
21” x 14 ½”

REV 4 - 1812041030

SINGLE DRAWER

MODEL:

-OUT:

CUT

33801
5 ¼” x 14 ½” x 20 ½”

ACCESS DOOR W/ DOUBLE DRAWERS

MODEL:

-OUT:

CUT

Also available: (not shown)

MODEL: 33914-SL CUT-OUT: 15” x 20 ½”
MODEL: 33917-SL CUT-OUT: 18” x 24 ½”
MODEL: 33920-SL CUT-OUT: 21” x 14 ½”
MODEL: 33924-SR or SL CUT-OUT: 25” x 17 ½”
MODEL: 33920-1-SR or SL CUT-OUT: 21” x 14 ½”
MODEL: 33938S CUT-OUT: 16” x 39”
MODEL: 33820-SL CUT-OUT: 21” x 14 ½” x 20 ½”
MODEL: 33820-TSR CUT-OUT: 21” x 14 ½” x 20 ½”
MODEL: 33930S-12 CUT-OUT: 21” x 30 ½” x 20 ½”

Available in left or right hinge

*

7

33810S
18 ½” x 30” x 26”

L-C2-358

LEGACY DOORS & DRAWERS

Cut-out is height x width x depth

MASONRY DRAWER

MODEL:

-OUT:

CUT

SINGLE ACCESS DOOR (RIGHT OR LEFT)
WITH TANK TRAY AND LOUVERS

MODEL:
CUT-OUT:

23830-S
13” x 31” x 20 ½”

23920-1T-S
20 ½” x 14 ½” x 20 ½”

SINGLE ACCESS DOOR

MODEL:

-OUT:

CUT

SINGLE ACCESS DOOR WITH LOUVERS

MODEL:

-OUT:

CUT

23917-S
17 ½” x 24 ½”

23920-1-S
20 ½” x 14 ½”

SINGLE ACCESS DOOR

MODEL:

-OUT:

CUT

DOUBLE ACCESS DOORS

MODEL:
CUT

23920-S
20 ½” x 14 ½”

-OUT:

23930S
20 ½” x 30”

DOUBLE DOORS WITH DUAL DRAWERS
AND TRASH TRAY

MODEL:

-OUT:

CUT

VENTING PANEL, LOUVERED STAINLESS STEEL

MODEL:
CUT
OUTER DIMENSIONS:

REV 4 - 1812041030

23930S-12

21” x 30 ½” x 20 ½”

-OUT:

5510-01
5” x 12 ¾”
6” x 14”

*

Available in left or right hinge

SINGLE DOOR WITH DUAL DRAWERS

MODEL:

-OUT:

CUT

23820-S
20 ½” x 14 ½” x 20 ½”

Also available: (not shown)

MODEL: 23912-S CUT-OUT: 12 ½” x 18 ½”
MODEL: 23918-S CUT-OUT: 18 ½” x 12 ½”
MODEL: 23924-S CUT-OUT: 24 ½” x 17 ½”
MODEL: 23914-S CUT-OUT: 14 ½” x 20 ½”
MODEL: 23912 CUT-OUT: 12 ½” x 18 ½”
MODEL: 23918 CUT-OUT: 18 ½” x 12 ½”
MODEL: 23924 CUT-OUT: 24 ½” x 17 ½”
MODEL: 23914 CUT-OUT: 14 ½” x 20 ½”
MODEL: 23917 CUT-OUT: 17 ½” x 24 ½”
MODEL: 23920 CUT-OUT: 20 ½” x 14 ½”
MODEL: 23920-1T CUT-OUT: 20 ½” x 14 ½” x 20 ½”
MODEL: 23920-1 CUT-OUT: 20 ½” x 14 ½”

8

L-C2-358

CARE & CLEANING

By following these recommendations, you will enjoy the beauty
and convenience of your unit for many years to come.

The trash should be emptied regularly.

STAINLESS STEEL

As needed, use a grill cleaner (or a soapy water solution) and
a clean cloth to remove grease and dirt from the outside of the
unit. For tough deposits, a copper pad can be used. Always
wipe with the grain. Rinse and dry completely. Then follow up
with a stainless steel cleaner and a clean cloth.

If this routine cleaning is not performed, the stainless steel
may become dull and develop surface rust (due to use and
atmospheric conditions). If left uncleaned, signifi cant damage
and pitting may occur.

Important: DO NOT use steel wool, any other metal tools,

or any other cleaners/chemicals to clean the
exterior other than recommended above. Such
items promote rust.

When this unit is installed in a corrosive environment such
as near the ocean (salt air), poolside (chlorine and/or pool
chemicals) or any other location with exposure to high salt/
chloride content or corrosive chemicals/solutions, it will be
more susceptible to corrosion and MUST be maintained/
cleaned more frequently.

Stainless

steel shown

Wipe with grain

Fig. 9-1

• DO NOT store any corrosive chemicals (chlorine,
hydrochloric acid, fertilizer, etc.) near your stainless steel
unit.

• DO NOT allow any corrosive materials (masonry dust,
debris, etc.) to settle on your stainless steel unit.

• These environments, chemicals, and materials may
cause the 304 stainless steel to develop surface rust and
consequently pitting. Under these conditions the unit MUST
be cleaned at least monthly. Inspect your unit often and
clean accordingly.

PORCELAIN

As needed, use a non-corrosive oven/grill cleaner (or a soapy
water solution) and a clean cloth to remove grease and dirt.
Rinse and dry completely.

REV 4 - 1812041030

9

L-C2-358

U

L

SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS

IMPORTANT FOR YOUR SAFETY

READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.

When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed.

FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION.

CYLINDER/CONNECTOR REQUIREMENTS

a. Propane-gas cylinders, valves, and hoses must be

maintained in good condition and must be replaced if
there is visible damage to either the cylinder or valve. If the
hose is cut or shows excessive abrasion or wear, it must
be replaced before using the gas appliance (see e.).

b. This unit, when used with a cylinder, should be connected

to a standard 5-gallon (20 lb.) propane-gas cylinder
equipped with an OPD (Overfi ll Prevention Device).
The OPD has been required on all cylinders sold since
October 1,1998, to prevent overfi lling.

c. Cylinder dimensions should be approximately 12" (30.5

cm) in diameter and 18" (45.7 cm) high. Cylinders must
be constructed and marked in accordance with the

Specifi cations for Propane Gas Cylinders of the U.S.
Department of Transportation (D.O.T.) or the National
Standard of Canada, CAN/CSA-B339, Cylinders,
Spheres, and Tubes for Transportation of Dangerous
Goods.

d. The cylinder used must include a collar to protect the

cylinder valve, and the cylinder supply system must be
arranged for vapor withdrawal.

e. The pressure regulator and hose assembly used must

e. The pressure regulator and hose assembly (Fig. 10-1)

match the specifi cation for Type I by ANSI Z 21.58/CGA

supplied with this outdoor gas appliance (L.P. models

1.6 (see Fig. 10-1).

only) must be used. Original and replacement pressure
regulator and hose assemblies must be those specifi ed by
the manufacturer for connection with a cylinder connecting
device identifi ed as Type I by the ANSI Z 21.58/CGA 1.6
(see PARTS LIST for ordering information).

f. The propane-gas cylinder valve must be equipped with a

cylinder connection coupling device, described as Type I
in the standard defi ned in paragraph e. above. This device
is commonly described as an Acme thread quick coupler.

g. If the propane-gas cylinder comes with a dust plug, place

the dust cap on the cylinder valve outlet whenever the
cylinder is not in use.

QUICK COUPLER OPERATION

To connect the regulator/hose assembly to the propane­gas cylinder valve fi tting: Press the hand nut on the regulator

over the Acme thread fi tting on the cylinder valve. Turn the hand
nut clockwise to engage the threads and tighten until snug.

The use of pliers or a wrench should not be necessary. Only
cylinders marked “propane” may be used.

To disconnect: Turn the hand nut counterclockwise until
detached (Fig. 10-1).

Important: Before using the unit, and after each time

the cylinder is removed and reattached,
check the hose for wear (see a.) and check
all connections for leaks. Turn off the unit
valves and open the main cylinder valve,
then check connections with soapy water.
Repair any leaks before lighting the unit.

CAUTION: Always turn the propane cylinder main valve

off after each use, and before moving the unit
and cylinder or disconnecting the coupling.
This valve must remain closed and the
cylinder disconnected while the appliance
is not in use, even though the gas fl ow is
stopped by a safety feature when the coupler
is disconnected.

Carefully inspect the hose assembly each time before the
gas is turned on. A cracked or frayed hose must be replaced
immediately.

If the appliance is stored indoors, the cylinder must be
disconnected and removed. Disconnected

cylinders must be

stored outdoors, out of the reach of children, with threaded
valve plugs tightly installed, and must not be stored in a

building, garage, or any other enclosed area.

FOR YOUR SAFETY

a. DO NOT store a spare propane-gas cylinder under or

near this appliance.

b. NEVER fi ll the cylinder beyond 80-percent full.

c. IF THE INFORMATION IN a. AND b. IS NOT FOLLOWED

EXACTLY, A FIRE CAUSING DEATH OR SERIOUS
INJURY MAY OCCUR.

Fig. 10-1 Type I Acme thread quick coupler

QCC
Type 1
valve

Pressure
relief
valve

Hand wheel

Brass Acme
thread fi tting

Liquid level
indicator
(optional)

Hand nut with Acme
thread

Regulator

Vent

Hose

ENCLOSURE REQUIREMENTS

FOR YOUR SAFETY, you must provide the openings listed below for replacement air and ventilation of the unit enclosure. One
side of the enclosure shall be left completely open to the outside; OR 4 (minimum) ventilation openings MUST be created:

• Each opening must have a minimum of 10 sq. in. of free area. The openings must be equally sized.

• Two openings must be in the side walls of the enclosure, at the top level, and spaced at a minimum of 90 degrees. The openings
must begin 1" or less below the countertop level and end no more than 5" below the countertop level.

• Two openings must be in the side walls of the enclosure, at the fl oor level, and spaced at a minimum of 90 degrees. The openings
must begin 1" or less above the fl oor level and end no more than 5" above the fl oor level.

• The openings must remain unobstructed: The clearance between the openings and any items outside of the enclosure is
a minimum of 6". The clearance between the openings and any items within the enclosure is a minimum of 2".

It is acceptable to use RHP venting panels (PN 5510-01). Contact your dealer.

KEEP THE REQUIRED VENT OPENINGS AND SURROUNDING AREA OF THE ENCLOSURE CLEAR AND FREE AT ALL TIMES.
WARNING: Ventilation openings in side walls shall not communicate directly with other enclosures of the outdoor cooking gas appliance.

10