DOOR & DRAWER
INSTALL SPECIFICATIONS
Model # 53830-S Shown
Model # 53930S Shown
GENERAL INFORMATION
WARNING
INSTALLER: Leave these instructions with consumer.
CONSUMER: Retain for future reference.
Important: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION
• When installing this unit directly below another unit, only install with Fire Magic built-in products.
• For proper installation, be sure to use the correct cutout dimensions as specifi ed for your specifi c
model number.
• It is recommended that silicon caulking (not supplied) is applied around the back of the door/
drawer cabinet trim before sliding the cabinet assembly into the opening.
• Some models may include an additional owner’s manual.
This unit is to be installed by a qualifi ed,
professional service technician.
• When used for propane cylinder storage, a louvered door model is required.
CAUTION: Make sure the enclosure is properly vented. See your grill owner’s manual for venting
requirements, or consult your local codes.
WHEN USING A PROPANE TANK CYLINDER:
• Never locate a cylinder under or near a grill unless suffi cient ventilation and shielding is
provided to prevent any heating of the cylinder regulator and hose. Refer to any additional
instructions included with your door (and/or your grill owner’s manual) for the required installation
method of propane tank cylinders.
• FOLLOW ALL THE SAFETY WARNING AND INFORMATION FOUND IN THESE
INSTRUCTIONS, ON YOUR PROPANE CYLINDER, AND IN YOUR GRILL OWNER’S MANUAL
ABOUT SAFE STORAGE AND USE OF PROPANE GAS.
ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746
REV 2 - 1410240935
1
L-C2-358
Drawer
support
Side View
Drawer
front
IN STA LLAT IO N G UID EL INE S
INSTALLATION GUIDELINES
DEPTH
H
E
I
G
H
T
WIDTH
H
E
I
WIDTH
G
H
T
Fig. 2-1 Cut-out Dimension Guide
For proper installation, be sure to use the correct cutout
dimensions as specifi ed for your specifi c model number. Locate
your model on the following pages for dimensions, and reference
Fig. 2-1 for proper orientation.
Fig. 2-2 Releasing drawer from slides
Fig. 2-3 Drawer Installation (Side View)
DRAWER
Before installing your drawer, remove the drawer from its base by
completely pulling it out. Release the drawer from the drawer slides
by pressing the black lever down on the right side, and up on the left
side
(Fig 2-2). Then pull outward on the drawer until it comes free of
the runners.
1. In order to properly support the weight of your drawer, it is necessary
to provide a secure, level surface in the rear of the unit. (See
2-3
) This may be accomplished by using bricks, 2 X 4’s, etc. Be
sure that the height of this rear support is 1/8" higher than that of
the front opening support, so that your drawer sits level.
2. Slide in and fasten the unit securely into the island enclosure using
the appropriate hardware for your enclosure (not supplied) through
the installation screw slots in the top and bottom of the unit.
3. To re-attach the drawer; extend the drawer slides completely and
align the drawer into the slides, pushing the drawer closed. Open
the drawer to verify that it has locked in place.
DOOR
Slide in and fasten the unit securely into the island enclosure using
the appropriate hardware for your enclosure (not supplied) through the
installation screw slots in the top and bottom of the unit.
Fig
For doors with propane tank trays:
To use, simply open the door, pull out the sliding cylinder tray, place
your cylinder on the tray and push the tray back in. The cylinder is
now ready for connection to your grill.
Important: Refer to any additional instructions included with
your door for the required installation method of
propane tank cylinders.
REV 2 - 1410240935
2
L-C2-358
FLUSH-MOUNTED DOORS & DRAWERS
Cut-out is height x width x depth
DOUBLE DOORS WITH DUAL DRAWERS
MODEL:
CUT-OUT:
53930S-22
21” x 30 ½” x 20 ½”
ELECTRIC WARMING DRAWER
MODEL:
CUT-OUT:
53830-SW
14 ½” x 32 ¼” x 22”
DOUBLE DOORS WITH TANK
TRAY & DUAL DRAWERS
MODEL:
CUT-OUT:
TRIPLE DRAWERS WITH TRAY
MODEL:
CUT-OUT:
53930S-12T
21” x 30 ½” x 20 ½”
53803
26 ¼” x 14 ½” x 20 ½”
MASONRY DRAWER WITH TRAY
MODEL:
CUT-OUT:
DOUBLE DRAWERS WITH TRAY
MODEL:
CUT-OUT:
53830-S
14 ½” x 32 ¼” x 22”
53802
15 ¾” x 14 ½” x 20 ½”
SINGLE ACCESS DOOR*
MODEL:
CUT-OUT:
REV 2 - 1410240935
53924-SL
25” x 17 ½”
DOUBLE ACCESS DOORS
MODEL:
CUT-OUT:
53934S
15” x 30”
Available in left or right hinge
*
3
SINGLE ACCESS DOOR W/ CABINET
& DOUBLE DRAWERS
MODEL:
CUT-OUT:
53810S
18 ½” x 30” x 26”
L-C2-358
FLUSH-MOUNTED DOORS & DRAWERS (cont.)
Cut-out is height x width x depth
DOUBLE ACCESS DOORS
MODEL:
CUT-OUT:
DOUBLE ACCESS DOORS
MODEL:
CUT-OUT:
53938S
16” x 39”
53930S
21” x 30”
SINGLE DOOR WITH DUAL DRAWERS*
MODEL:
CUT-OUT:
SINGLE ACCESS DOOR*
MODEL:
CUT-OUT:
53820-SR
21” x 14 ½” x 20 ½”
53920-SL
21” x 14 ½”
SINGLE DRAWER WITH TRAY
MODEL:
CUT-OUT:
SINGLE ACCESS DOOR*
MODEL:
CUT-OUT:
53801
5 ¼” x 14 ½” x 20 ½”
53917-SR
18” x 24 ½”
SINGLE ACCESS DOOR*
MODEL:
CUT-OUT:
REV 2 - 1410240935
53914-SR
15” x 20 ½”
DOUBLE ACCESS DOORS
WITH LOUVERS
MODEL:
CUT-OUT:
53930S-1
21” x 30”
ACCESS DOORS AND DOUBLE DRAWERS
MODEL:
CUT-OUT:
53816S
18 ½” x 36½” x 26”
Also available: (not shown)
MODEL: 53914-SL CUT-OUT: 15” x 20 ½”
MODEL: 53917-SL CUT-OUT: 18 ½” x 24 ½”
MODEL: 53924-SR CUT-OUT: 25” x 17 ½”
MODEL: 53920-SR CUT-OUT: 21” x 14 ½”
MODEL: 53820-SL CUT-OUT: 21” x 14 ½” x 20 ½”
MODEL: 53930S-12 CUT-OUT: 21” x 30 ½” x 20 ½”
MODEL: 53820-TSR or TSL CUT-OUT: 21” x 14 ½” x 20 ½”
Available in left or right hinge
*
4
L-C2-358
PR EMIU M DO O RS & DR AWE R S
PREMIUM DOORS & DRAWERS
Cut-out is height x width x depth
ELECTRIC WARMING DRAWER
MODEL:
CUT-OUT:
43830-SW
13” x 31” x 20 ½”
DOUBLE ACCESS DOORS
MODEL:
CUT-OUT:
43934S
15” x 30”
MASONRY DRAWER WITH TRAY
MODEL:
CUT-OUT:
TRIPLE DRAWERS WITH TRAY
MODEL:
CUT-OUT:
43830-S
13” x 31” x 20 ½”
43803T
26 ¼” x 14 ½” x 20 ½”
DOUBLE DRAWERS WITH TRAY
MODEL:
CUT-OUT:
SINGLE ACCESS DOOR WITH TANK TRAY
AND LOUVERS*
MODEL:
CUT-OUT:
43802
15 ¾” x 14 ½” x 20 ½”
43820-TSL
21” x 14 ½” x 20 ½”
DOUBLE DOORS WITH TANK TRAY,
LOUVERS, AND DUAL DRAWERS
MODEL:
CUT-OUT:
REV 2 - 1410240935
43930S-12T
21” x 30 ½” x 20 ½”
ACCESS DOORS AND DOUBLE DRAWERS
MODEL:
CUT-OUT:
Available in left or right hinge
*
5
43816S
18 ½” x 36½” x 26”
L-C2-358
PR E MIU M DO O RS & D R AWE R S ( c on t . )
PREMIUM DOORS & DRAWERS (cont.)
Cut-out is height x width x depth
SINGLE DOOR WITH DUAL DRAWERS*
MODEL:
CUT-OUT:
43820-SL
21” x 14 ½” x 20 ½”
SINGLE DRAWER WITH TRAY
MODEL:
CUT-OUT:
43801
5 ¼” x 14 ½” x 20 ½”
SINGLE ACCESS DOOR*
MODEL:
CUT-OUT:
SINGLE ACCESS DOOR*
MODEL:
CUT-OUT:
43920-SR
21” x 14 ½”
43914-SR
15” x 20 ½”
DOUBLE ACCESS DOORS
MODEL:
CUT-OUT:
SINGLE ACCESS DOOR*
MODEL:
CUT-OUT:
43930S
21” x 30”
43917-SR
18” x 24 ½”
DOUBLE DOORS WITH 2 DUAL DRAWERS
MODEL:
CUT-OUT:
43930S-22
21” x 30 ½” x 20 ½”
Also available: (not shown)
MODEL: 43914-SL CUT-OUT: 15” x 20 ½”
MODEL: 43917-SL CUT-OUT: 18” x 24 ½”
MODEL: 43924-SR or SL CUT-OUT: 25” x 17 ½”
MODEL: 43920-SL CUT-OUT: 21” x 14 ½”
MODEL: 43938S CUT-OUT: 16” x 39”
MODEL: 43930S-12 CUT-OUT: 21” x 30 ½” x 20 ½”
MODEL: 43820-TSR CUT-OUT: 21” x 14 ½” x 20 ½”
REV 2 - 1410240935
DOUBLE ACCESS DOORS WITH
LOUVERS
MODEL:
CUT-OUT:
Available in left or right hinge
*
43930S-1
21” x 30”
6
SINGLE ACCESS DOOR W/ CABINET
& DOUBLE DRAWERS
MODEL:
CUT-OUT:
43810S
18 ½” x 30” x 26”
L-C2-358
SELECT DOORS & DRAWERS
Cut-out is height x width x depth
ELECTRIC WARMING DRAWER
MODEL:
CUT-OUT:
TRIPLE DRAWERS WITH TRAY
MODEL:
CUT-OUT:
33830-SW
13” x 31” x 20 ½”
33803
26 ¼” x 14 ½” x 20 ½”
MASONRY DRAWER WITH TRAY
MODEL:
CUT-OUT:
DOUBLE DRAWERS WITH TRAY
MODEL:
CUT-OUT:
33802
15 ¾” x 14 ½” x 20 ½”
33830-S
13” x 31” x 20 ½”
DOUBLE ACCESS DOORS
MODEL:
CUT-OUT:
DOUBLE DOORS WITH TANK TRAY, LOUVERS,
AND DUAL DRAWERS
MODEL:
CUT-OUT:
33930S-12T
21” x 30 ½” x 20 ½”
33930S
21” x 30”
REV 2 - 1410240935
SINGLE DOOR WITH DUAL DRAWERS*
MODEL:
CUT-OUT:
33820-SR
21” x 14 ½” x 20 ½”
*
Available in left or right hinge
ACCESS DOORS AND DOUBLE DRAWERS
MODEL:
CUT-OUT:
33816S
18 ½” x 36½” x 26”
7
L-C2-358
SELECT DOORS & DRAWERS (cont.)
Cut-out is height x width x depth
SINGLE ACCESS DOOR*
MODEL:
CUT-OUT:
33914-SR
15” x 20 ½”
SINGLE ACCESS DOOR WITH TANK
TRAY AND LOUVERS*
MODEL:
CUT-OUT:
DOUBLE DOORS WITH 2 DUAL DRAWERS
MODEL:
CUT-OUT:
33820-TSL
21” x 14 ½” x 20 ½”
33930S-22
21” x 30 ½” x 20 ½”
SINGLE ACCESS DOOR*
MODEL:
CUT-OUT:
SINGLE ACCESS DOOR*
MODEL:
CUT-OUT:
33917-SR
18” x 24 ½”
33920-SR
21” x 14 ½”
REV 2 - 1410240935
SINGLE DRAWER WITH TRAY
MODEL:
CUT-OUT:
33801
5 ¼” x 14 ½” x 20 ½”
SINGLE ACCESS DOOR W/ CABINET
& DOUBLE DRAWERS
MODEL:
CUT-OUT:
Also available: (not shown)
MODEL: 33914-SL CUT-OUT: 15” x 20 ½”
MODEL: 33917-SL CUT-OUT: 18” x 24 ½”
MODEL: 33920-SL CUT-OUT: 21” x 14 ½”
MODEL: 33924-SR or SL CUT-OUT: 25” x 17 ½”
MODEL: 33938S CUT-OUT: 16” x 39”
MODEL: 33820-SL CUT-OUT: 21” x 14 ½” x 20 ½”
MODEL: 33820-TSR CUT-OUT: 21” x 14 ½” x 20 ½”
MODEL: 33930S-12 CUT-OUT: 21” x 30 ½” x 20 ½”
Available in left or right hinge
*
8
33810S
18 ½” x 30” x 26”
L-C2-358
LE G ACY D OO R S & D RAW ER S
LEGACY DOORS & DRAWERS
Cut-out is height x width x depth
MASONRY DRAWER WITH TRAY
MODEL:
CUT-OUT:
SINGLE ACCESS DOOR (RIGHT OR LEFT)
WITH TANK TRAY AND LOUVERS
MODEL:
CUT-OUT:
23830-S
13” x 31” x 20 ½”
23920-1T-S
20 ½” x 14 ½” x 20 ½”
SINGLE ACCESS DOOR
MODEL:
CUT-OUT:
SINGLE ACCESS DOOR WITH LOUVERS
MODEL:
CUT-OUT:
23917-S
17 ½” x 24 ½”
23920-1-S
20 ½” x 14 ½”
SINGLE ACCESS DOOR
MODEL:
CUT-OUT:
DOUBLE ACCESS DOORS
MODEL:
CUT-OUT:
23920-S
20 ½” x 14 ½”
23930S
20 ½” x 30”
DOUBLE DOORS WITH DUAL DRAWERS
AND TRASH TRAY
MODEL:
CUT-OUT:
VENTING PANEL, LOUVERED STAINLESS STEEL
MODEL:
CUT-OUT:
REV 2 - 1410240935
23930S-12
21” x 30 ½” x 20 ½”
5510-01
3 ¾” x 12 ¾”
SINGLE DOOR WITH DUAL DRAWERS
MODEL:
CUT-OUT:
23820-S
20 ½” x 14 ½” x 20 ½”
Also available: (not shown)
MODEL: 23912-S CUT-OUT: 12 ½” x 18 ½”
MODEL: 23918-S CUT-OUT: 18 ½” x 12 ½”
MODEL: 23924-S CUT-OUT: 24 ½” x 17 ½”
MODEL: 23914-S CUT-OUT: 14 ½” x 20 ½”
Available in left or right hinge
*
9
DRAWER WITH PROPANE DOOR ASSY
MODEL:
CUT-OUT:
25914-S
27 ¾” x 14 ½” x 20 ½”
L-C2-358
CARE & CLEANING
CARE AND CLEANING
Clean your unit by fi rst using Fire Magic Barbecue and
Grill Cleaner (part #3580-1) to remove grease and dirt.
Always wipe with the grain (See Fig. 10-1). Next, use
Fire Magic Stainless Steel Cleaner (3581-1) to restore
the stainless steel color. Finish by wiping your unit down
using Fire Magic Polish Wipes (3586-1).
If your unit is installed in a seaside (salt air) or poolside
(chlorine) location, it will be more susceptible to corrosion
and must be maintained/cleaned more frequently. Do not
store chemicals (such as chlorine or fertilizer) near your
stainless steel unit.
Due to the nature of stainless steel, surface iron oxide
deposits may appear. Do not be alarmed – these
deposits are removable with stainless-steel cleaner
through prompt and periodic maintenance. If not
attended to promptly, permanent pitting may occur.
By following these recommendations, you will enjoy the
beauty and convenience of your unit for many years to
come.
Wipe with grain
Fig. 10-1
REV 2 - 1410240935
10
L-C2-358
U
L
SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS
IMPORTANT FOR YOUR SAFETY
READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.
When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed.
FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION.
CYLINDER/CONNECTOR REQUIREMENTS
a. Propane-gas cylinders, valves, and hoses must be
maintained in good condition and must be replaced if
there is visible damage to either the cylinder or valve. If the
hose is cut or shows excessive abrasion or wear, it must
be replaced before using the gas appliance (see e.).
b. This unit, when used with a cylinder, should be connected
to a standard 5-gallon (20 lb.) propane-gas cylinder
equipped with an OPD (Overfi ll Prevention Device).
The OPD has been required on all cylinders sold since
The use of pliers or a wrench should not be necessary. Only
cylinders marked “propane” may be used.
To disconnect: Turn the hand nut counterclockwise until
detached (Fig. 11-1).
Important: Before using the unit, and after each time the
cylinder is removed and reattached, check
the hose for wear (see a.) and check all
connections for leaks. Turn off the unit valves
and open the main cylinder valve, then check
connections with soapy water. Repair any
leaks before lighting the unit.
October 1,1998, to prevent overfi lling.
c. Cylinder dimensions should be approximately 12" (30.5
cm) in diameter and 18" (45.7 cm) high. Cylinders must
be constructed and marked in accordance with the
Specifi cations for Propane Gas Cylinders of the U.S.
Department of Transportation (D.O.T.) or the National
Standard of Canada, CAN/CSA-B339, Cylinders,
Spheres, and Tubes for Transportation of Dangerous
Goods.
d. The cylinder used must include a collar to protect the
cylinder valve, and the cylinder supply system must be
arranged for vapor withdrawal.
e. The pressure regulator and hose assembly used must
e. The pressure regulator and hose assembly (Fig. 11-1)
match the specifi cation for Type I by ANSI Z 21.58-2005/
supplied with this outdoor-cooking gas appliance must
CGA 1.6-2005 (see Fig. 11-1).
be used. Original and replacement pressure regulator
and hose assemblies must be those specifi ed by the
manufacturer for connection with a cylinder connecting
device identifi ed as Type I by the ANSI Z 21.58-2005/CGA
1.6-2005 (see PARTS LIST for ordering information).
f. The propane-gas cylinder valve must be equipped with a
cylinder connection coupling device, described as Type
I in the standard defi ned in paragraph e. above. This
device is commonly described as an Acme thread quick
coupler.
g. If the propane-gas cylinder comes with a dust plug, place
the dust cap on the cylinder valve outlet whenever the
cylinder is not in use.
QUICK COUPLER OPERATION
To connect the regulator/hose assembly to the propanegas cylinder valve fi tting: Press the hand nut on the regulator
over the Acme thread fi tting on the cylinder valve. Turn the hand
CAUTION: Always turn the propane cylinder main valve
off after each use, and before moving the unit
and cylinder or disconnecting the coupling.
This valve must remain closed and the
cylinder disconnected while the appliance
is not in use, even though the gas fl ow is
stopped by a safety feature when the coupler
is disconnected.
Carefully inspect the hose assembly each time before the
gas is turned on. A cracked or frayed hose should be replaced
immediately.
If the appliance is stored indoors, the cylinder must be
disconnected and removed. Disconnected
cylinders must be
stored outdoors, out of the reach of children, with threaded
valve plugs tightly installed, and must not be stored in a
building, garage, or any other enclosed area.
FOR YOUR SAFETY
a. DO NOT store a spare propane-gas cylinder under or
near this appliance.
b. NEVER fi ll the cylinder beyond 80-percent full.
c. IF THE INFORMATION IN a. AND b. IS NOT FOLLOWED
EXACTLY, A FIRE CAUSING DEATH OR SERIOUS
INJURY MAY OCCUR.
Fig. 11-1 Type I Acme thread quick coupler
QCC
Type 1
valve
Pressure
relief
valve
Hand wheel
Brass Acme
thread fi tting
Liquid level
indicator
(optional)
Hand nut with Acme
thread
Regulator
Hose
nut clockwise to engage the threads and tighten until snug.
ENCLOSURE REQUIREMENTS
FOR YOUR SAFETY, you must provide the openings listed below for drainage, replacement air, and cross-ventilation
of any storage area exposed to possible leakage from gas connections, the unit, or propane cylinders:
One side of the gas cylinder enclosure left completely open to the outside OR by providing four (4) ventilation
openings. Two (2) openings are to be at the cylinder valve level (approx. 16" [40.6 cm] above the fl oor) and on
opposite walls of the enclosure. Two (2) more openings must be at the fl oor level on opposite sides of the enclosure.
The fl oor-level openings must start at the fl oor and shall extend no higher than 5" (12.7 cm) above the fl oor. Each
opening must have a minimum of 10 sq. in. (64.5 cm2) of free area. To achieve the proper ventilation, you may drill
a series of holes, omit the grout from masonry joints, or replace a brick with a hardware cloth screen. If the fl oor
in the cabinet is raised and the space beneath the cabinet is open to the outside, the lower ventilation openings
may be in the fl oor.
Consult your gas supplier for ventilation and regulator requirements when connecting to a household propane supply.
Vent
11
NOTES PAGE
Please use this page to record any information about your door/drawer that you may want to have at hand.
12
Loading...