OUTDOOR BUILT-IN SINK
Model #: 3587
INSTALLER: Leave these instructions with consumer.
CONSUMER: Retain for future reference.
Sink shown here with faucet (not included but
available separately, design may vary)
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE
Specifi cation Value
Counter opening width 14"
Counter opening length 14"
Min. vert. clearance below counter 17"
Counter overlap beyond cutout
1
/
Table 1-1 Specifi cations table
"
2
14"
17"
1/2" clearance all
the way around
14"
PREPARE FOR INSTALLATION
This product is intended to be used as an outdoor
sink and must be installed by a licensed professional
plumber according to all applicable local codes.
Prepare a cut-out in the countertop as specifi ed in
Table 1-1 and shown in Fig. 1-1. There must be a
minimum of 1/2" overlap of the stainless-steel hanger
plate on all sides of the opening. The countertop must
be completely level for safe and effective operation
of this appliance.
Provide for access beneath the sink before and after
installation to allow for proper maintenance. Allow for
adequate water line and drain connections.
Fig. 1-1 Cut out dimensions detail
Sink
Foam-rubber
gasket
Anchor clips
Drain Kit
Important: All plastic fittings must be hand
tightened only! DO NOT use wrenches
on plastic fi ttings.
ATTACH FOAM-RUBBER GASKET
1. Gently place the sink up-side-down on the
countertop or other work surface. Locate the
foam-rubber gasket and begin to peel away the
protective paper.
2. Attach the adhesive side of the foam rubber liner
around the under side of the sink lip (see Fig. 1-3).
ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746
REV 4 - 1301300830
Fig. 1-2 Sink detail
(Sink bottom)
Foam-rubber
gasket
Fig. 1-3 Attach foam-rubber gasket
1
L-C2-270
SINK INSTALLATION (cont.)
INSTALL DRAIN ASSEMBLY
1. Pull out the plug from the drain assembly, and
remove the exposed retaining bolt using a
Flathead screwdriver or a 9/16" nut driver (see
Fig. 2-1).
2. Separate the upper drain fi tting from the remainder
of the drain assembly, being sure to keep one
rubber gasket on each part (see Fig. 2-2).
(A) Remove
drain plug
3. Turn the sink on its side, and insert the upper
drain fi tting into the hole on the bottom of the sink.
Ensure the ribbed gasket is between the metal
of the sink and the fi tting. See Fig. 2-3.
4. Insert the retaining bolt into the upper drain fi tting.
With the grooved gasket resting in the lower
drain assembly, orient the assembly against the
bottom of the sink, align with the retaining bolt,
and hand tighten. See Fig. 2-4.
5. Complete tightening by using the screwdriver /
nut driver to apply a fi nal quarter-turn.
(B) Remove retaining bolt
Fig. 2-1 Remove drain plug and retaining bolt
Grooved gasket
Ribbed gasket
(bottom of upper
drain fi tting)
Fig. 2-2 Remove upper drain fi tting
Ribbed gasket
Upper drain
fi tting
REV 4 - 1301300830
Fig. 2-3 Insert upper drain fi tting in sink
(A) Insert retaining bolt
(from inside of sink)
(B) Attach lower drain assembly
Fig. 2-4 Insert retaining bolt and attach lower drain
2
L-C2-270
SINK INSTALLATION (cont.)
INSTALL SINK
1. After application of any silicon sealant, lower the
sink into the counter cut-out with the Fire Magic
logo toward the back.
2. From underneath the counter, connect the eight
anchor clips to the punched tabs around the
outside of the sink by snapping them into place
as shown in Fig. 3-1.
3. Hook each clip claw under the inside bottom of
the counter and tighten the screw until enough
tension exists to hold the sink fi rmly down against
the counter (see Fig. 3-2).
4. Install a faucet or plug (not included) into the
opening in the top of the sink.
5. Insert the drain plug into the sink drain.
Fig. 3-1
View beneath
countertop
(countertop not
shown for clarity)
Connect anchor clips to sink (below countertop)
INSTALL SUPPLIED PIPING
1. Assemble the supplied piping and install to
the bottom of the drain assembly. (Various
confi gurations are available for the individual
setup. An example is shown in Fig. 3-3.)
Alternatively, the provided hose adapter may be
installed to the bottom of the drain assembly.
Important: Use rubber rings to seal drain
compression fi ttings.
All plastic fi ttings must be hand
tightened only! DO NOT use wrenches
on plastic fi ttings.
2. Plumb out the system as appropriate for the
installation.
Clip
Claw
Tightening screw
Fig. 3-2 Anchor detail
REV 4 - 1301300830
Fig. 3-3 Drain assembly example
3
L-C2-270
CARE & CLEANING
DRAIN MAINTENANCE
The sink drain assembly is equipped with a removable
trap for larger food particles. This prevents larger
food particles from entering and blocking the drain
plumbing. Regularly check the drain trap and clean
out any foreign matter it contains to help keep the
drain functioning at its best. To remove the drain
trap simply unscrew it from the bottom of the drain
assembly (see Fig. 4-1).
CLEANING THE SINK
This sink has a stainless steel fi nish. Use a standard
non-abrasive kitchen cleaner for basic cleaning or
a quality stainless-steel cleaner if heavy cleaning is
required.
Clean the sink at least once a month, following the
instructions on the cleaner. Always rub stainless steel
in the direction of the grain (see Fig. 4-2).
Fig. 4-1 Drain trap cleaning
Fig. 4-2 Always wipe with the grain
REV 4 - 1301300830
4
L-C2-270
Loading...