Fire Magic 33816S User Manual

DOOR & DRAWER

INSTALL SPECIFICATIONS

Model # 53830-S Shown

Model # 53930S Shown

GENERAL INFORMATION

WARNING

INSTALLER: Leave these instructions with consumer.

CONSUMER: Retain for future reference.

Important: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION

• When installing this unit directly below another unit, only install with Fire Magic built-in products.

• For proper installation, be sure to use the correct cutout dimensions as specifi ed for your specifi c
model number.

• It is recommended that silicon caulking (not supplied) is applied around the back of the door/
drawer cabinet trim before sliding the cabinet assembly into the opening.

• Some models may include an additional owner’s manual.

This unit is to be installed by a qualifi ed,

professional service technician.

• When used for propane cylinder storage, a louvered door model is required.

CAUTION: Make sure the enclosure is properly vented. See your grill owner’s manual for venting

requirements, or consult your local codes.

WHEN USING A PROPANE TANK CYLINDER:

• Never locate a cylinder under or near a grill unless suffi cient ventilation and shielding is
provided to prevent any heating of the cylinder regulator and hose. Refer to any additional

instructions included with your door (and/or your grill owner’s manual) for the required installation
method of propane tank cylinders.

• FOLLOW ALL THE SAFETY WARNING AND INFORMATION FOUND IN THESE
INSTRUCTIONS, ON YOUR PROPANE CYLINDER, AND IN YOUR GRILL OWNER’S MANUAL
ABOUT SAFE STORAGE AND USE OF PROPANE GAS.

ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746

REV 2 - 1410240935

1

L-C2-358

Drawer
support

Side View

Drawer

front

IN STA LLAT IO N G UID EL INE S

INSTALLATION GUIDELINES

DEPTH

H
E

I
G
H
T

WIDTH

H
E

I

WIDTH

G
H
T

Fig. 2-1 Cut-out Dimension Guide

For proper installation, be sure to use the correct cutout
dimensions as specifi ed for your specifi c model number. Locate
your model on the following pages for dimensions, and reference

Fig. 2-1 for proper orientation.

Fig. 2-2 Releasing drawer from slides

Fig. 2-3 Drawer Installation (Side View)

DRAWER

Before installing your drawer, remove the drawer from its base by
completely pulling it out. Release the drawer from the drawer slides
by pressing the black lever down on the right side, and up on the left
side

(Fig 2-2). Then pull outward on the drawer until it comes free of

the runners.

1. In order to properly support the weight of your drawer, it is necessary
to provide a secure, level surface in the rear of the unit. (See
2-3

) This may be accomplished by using bricks, 2 X 4’s, etc. Be
sure that the height of this rear support is 1/8" higher than that of
the front opening support, so that your drawer sits level.

2. Slide in and fasten the unit securely into the island enclosure using
the appropriate hardware for your enclosure (not supplied) through
the installation screw slots in the top and bottom of the unit.

3. To re-attach the drawer; extend the drawer slides completely and
align the drawer into the slides, pushing the drawer closed. Open
the drawer to verify that it has locked in place.

DOOR

Slide in and fasten the unit securely into the island enclosure using
the appropriate hardware for your enclosure (not supplied) through the
installation screw slots in the top and bottom of the unit.

Fig

For doors with propane tank trays:

To use, simply open the door, pull out the sliding cylinder tray, place
your cylinder on the tray and push the tray back in. The cylinder is
now ready for connection to your grill.

Important: Refer to any additional instructions included with

your door for the required installation method of
propane tank cylinders.

REV 2 - 1410240935

2

L-C2-358

FLUSH-MOUNTED DOORS & DRAWERS

Cut-out is height x width x depth

DOUBLE DOORS WITH DUAL DRAWERS
MODEL:
CUT-OUT:

53930S-22
21” x 30 ½” x 20 ½”

ELECTRIC WARMING DRAWER

MODEL:
CUT-OUT:

53830-SW
14 ½” x 32 ¼” x 22”

DOUBLE DOORS WITH TANK
TRAY & DUAL DRAWERS

MODEL:
CUT-OUT:

TRIPLE DRAWERS WITH TRAY

MODEL:
CUT-OUT:

53930S-12T
21” x 30 ½” x 20 ½”

53803
26 ¼” x 14 ½” x 20 ½”

MASONRY DRAWER WITH TRAY

MODEL:
CUT-OUT:

DOUBLE DRAWERS WITH TRAY

MODEL:
CUT-OUT:

53830-S
14 ½” x 32 ¼” x 22”

53802
15 ¾” x 14 ½” x 20 ½”

SINGLE ACCESS DOOR*

MODEL:
CUT-OUT:

REV 2 - 1410240935

53924-SL
25” x 17 ½”

DOUBLE ACCESS DOORS

MODEL:
CUT-OUT:

53934S
15” x 30”

Available in left or right hinge

*

3

SINGLE ACCESS DOOR W/ CABINET
& DOUBLE DRAWERS

MODEL:
CUT-OUT:

53810S
18 ½” x 30” x 26”

L-C2-358

FLUSH-MOUNTED DOORS & DRAWERS (cont.)

Cut-out is height x width x depth

DOUBLE ACCESS DOORS

MODEL:
CUT-OUT:

DOUBLE ACCESS DOORS

MODEL:
CUT-OUT:

53938S
16” x 39”

53930S
21” x 30”

SINGLE DOOR WITH DUAL DRAWERS*

MODEL:
CUT-OUT:

SINGLE ACCESS DOOR*

MODEL:
CUT-OUT:

53820-SR
21” x 14 ½” x 20 ½”

53920-SL
21” x 14 ½”

SINGLE DRAWER WITH TRAY

MODEL:
CUT-OUT:

SINGLE ACCESS DOOR*

MODEL:
CUT-OUT:

53801
5 ¼” x 14 ½” x 20 ½”

53917-SR
18” x 24 ½”

SINGLE ACCESS DOOR*

MODEL:
CUT-OUT:

REV 2 - 1410240935

53914-SR
15” x 20 ½”

DOUBLE ACCESS DOORS
WITH LOUVERS

MODEL:
CUT-OUT:

53930S-1
21” x 30”

ACCESS DOORS AND DOUBLE DRAWERS

MODEL:
CUT-OUT:

53816S
18 ½” x 36½” x 26”

Also available: (not shown)

MODEL: 53914-SL CUT-OUT: 15” x 20 ½”
MODEL: 53917-SL CUT-OUT: 18 ½” x 24 ½”
MODEL: 53924-SR CUT-OUT: 25” x 17 ½”
MODEL: 53920-SR CUT-OUT: 21” x 14 ½”
MODEL: 53820-SL CUT-OUT: 21” x 14 ½” x 20 ½”
MODEL: 53930S-12 CUT-OUT: 21” x 30 ½” x 20 ½”
MODEL: 53820-TSR or TSL CUT-OUT: 21” x 14 ½” x 20 ½”

Available in left or right hinge

*

4

L-C2-358