Firemagic 3092B User Manual

1-Hour Automatic Timer

IN

OFF

60

MINUTES

40

MINUTES

20

MINUTES

TURN

PAST

Shut-Off Valve

Model# 3092B

INSTALLER: Leave these instructions with consumer.
CONSUMER: Retain for future reference.

SPECIFICATIONS

• 100,000 B.T.U., Natural Gas @ 0.6 SP. @ 7" w.c.

• 100,000 B.T.U., Propane Gas @ 1.53 SP.@ 11" w.c.

• Maximum working pressure not to exceed 1/2 P.S.I.G.

• Maximum ambient operating range: from 0° F (-18°
C) to 150° F (65.6° C).

INSTALLATION REQUIREMENTS

• Timer MUST be installed in accordance with local
codes or, in the absence of local codes, in accordance
with the National Fuel Gas Code ANSI Z223.1/
NFPA54, or the Natural Gas & Propane Installation
Code, CSA B149.1, as applicable.

• Timer MUST be installed in-line between the shut-off
valve and the gas appliance.

• Timer MUST be installed a minimum of 18" away from
the appliance or it will overheat, causing damage to
the timer and may result in a leak.

• Timer MUST be installed within 6 feet of the appliance.
If it is located within the appliance enclosure, it must
be easily accessible.

• Timer MUST be protected from high temperatures
and outdoor elements.

• Use pipe joint compound resistant to all gasses on all
NPT fittings except flare fittings. Be sure to leak test
at all connections.

(Setup may vary)

Shut-off valve (shown
in-line) must be within
6 feet of the appliance

AND before the timer

Gas supply

(NPT)

Automatic

shut-off timer

(NPT-to-NPT)

Fig. 1-1 Timer installation overview

HORIZONTAL SETUP

Gas flow direction

(to appliance)

Gas supply

side (IN)

Timer must be a
minimum of 18"

from the appliance

(max. 6 ft.)

Flare-to-NPT

adapter

Timer must be protected

from high temperatures and

outdoor elements

Flex

connector

Appliance

side

Gas

appliance

INSTALLATION

In addition to following the CONNECT GAS SUPPLY section
of the gas appliance owner’s manual, install the timer in
the gas supply line (between the shut-off valve and the
appliance). See Fig. 1-1 and 1-2.

• Ensure you connect the line coming from the gas
supply to the side marked “IN” on the timer.

• The timer accommodates 1/2" NPT piping (both
ends).

• Follow ALL information found in the requirements
section above, in the gas appliance owner’s
manual, and in Fig. 1-1 and 1-2.

• The timer can be installed horizontally or vertically.

ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746

REV 1 - A - 1912031615

VERTICAL SETUP

Appliance

side

Gas flow
direction

(to appliance)

Gas supply

side (IN)

Fig. 1-2 Timer installation detail

1

L-C2-559

OPERATION

To use, set the dial (turn clockwise) to the desired time to
shut off. The dial is marked in 3 twenty minute increments
(any position in between is an estimate of that set time).
The timer dial will auto rotate (counter-clockwise) and
will shut off the gas supply when the dial reaches OFF
(i.e. the time is completed).

Important: When using the timer for periods of less

than twenty minutes, you must first set
the dial to 20 minutes (to activate), then
return (counter-clockwise) to the desired
amount of time. This will ensure proper
timer operation. See Fig. 2-1.

CAUTION: Always leave the shut-off valve in the OFF

position when not in use.

(Horizontal setup shown)

Timer setting mark

(shown here in OFF)

Turn past

20 minutes to

activate

(see important

in text)

Time settings:
20-60 minutes

Fig. 2-1 Timer operation

REV 1 - A - 1912031615

2

L-C2-559