Fire-Lite Alarms MS-5024UD, MS-5024UDE User Manual

PN: 15140:G ECN 01-685

Fire Alarm Control Panel

MS-5024UD/MS-5024UDE

Document #15140
01/02/02 Revision

G

Fire Alarm System Limitations

While a fire alarm system may lower insurance
rates, it is not a substitute for fire insurance!

An automatic fire alarm system–typically made up of smoke
detectors, heat detectors, manual pull stations, audible warn­ing devices, and a fire alarm control with remote notification
capability–can provide early warning of a developing fire.
Such a system, however, does not assure protection against
property damage or loss of life resulting from a fire.

The Manufacturer recommends that smoke and/or heat detec­tors be located throughout a protected premise following the
recommendations of the current edition of the National Fire
Protection Association Standard 72 (NFPA 72),
manufacturer's recommendations, State and local codes, and
the recommendations contained in the Guide for Proper Use
of System Smoke Detectors, which is made available at no
charge to all installing dealers. A study by the Federal Emer­gency Management Agency (an agency of the United States
government) indicated that smoke detectors may not go off in
as many as 35% of all fires. While fire alarm systems are de­signed to provide early warning against fire, they do not guar­antee warning or protection against fire. A fire alarm system
may not provide timely or adequate warning, or simply may not
function, for a variety of reasons:

Smoke detectors may not sense fire where smoke cannot
reach the detectors such as in chimneys, in or behind walls, on
roofs, or on the other side of closed doors. Smoke detectors
also may not sense a fire on another level or floor of a build­ing. A second-floor detector, for example, may not sense a
first-floor or basement fire.

Particles of combustion or "smoke" from a developing fire
may not reach the sensing chambers of smoke detectors be­cause:

• Barriers such as closed or partially closed doors, walls, or
chimneys may inhibit particle or smoke flow.

• Smoke particles may become "cold," stratify, and not reach
the ceiling or upper walls where detectors are located.

• Smoke particles may be blown away from detectors by air
outlets.

• Smoke particles may be drawn into air returns before reach­ing the detector.

The amount of "smoke" present may be insufficient to alarm
smoke detectors. Smoke detectors are designed to alarm at
various levels of smoke density. If such density levels are not
created by a developing fire at the location of detectors, the
detectors will not go into alarm.

Smoke detectors, even when working properly, have sensing
limitations. Detectors that have photoelectronic sensing
chambers tend to detect smoldering fires better than flaming
fires, which have little visible smoke. Detectors that have ion­izing-type sensing chambers tend to detect fast-flaming fires
better than smoldering fires. Because fires develop in differ­ent ways and are often unpredictable in their growth, neither
type of detector is necessarily best and a given type of detec­tor may not provide adequate warning of a fire.

Smoke detectors cannot be expected to provide adequate
warning of fires caused by arson, children playing with
matches (especially in bedrooms), smoking in bed, and violent
explosions (caused by escaping gas, improper storage of
flammable materials, etc.).

Heat detectors do not sense particles of combustion and
alarm only when heat on their sensors increases at a prede­termined rate or reaches a predetermined level. Rate-of-rise
heat detectors may be subject to reduced sensitivity over time.
For this reason, the rate-of-rise feature of each detector
should be tested at least once per year by a qualified fire pro­tection specialist. Heat detectors are designed to protect

property, not life.

IMPORTANT! Smoke detectors must be installed in the
same room as the control panel and in rooms used by the sys­tem for the connection of alarm transmission wiring, communi­cations, signaling, and/or power. If detectors are not so lo-

cated, a developing fire may damage the alarm system, crip­pling its ability to report a fire.

Audible warning devices such as bells may not alert people
if these devices are located on the other side of closed or
partly open doors or are located on another floor of a building.
Any warning device may fail to alert people with a disability or
those who have recently consumed drugs, alcohol or medica­tion. Please note that:

• Strobes can, under certain circumstances, cause seizures
in people with conditions such as epilepsy.

• Studies have shown that certain people, even when they
hear a fire alarm signal, do not respond or comprehend the
meaning of the signal. It is the property owner's responsibil­ity to conduct fire drills and other training exercise to make
people aware of fire alarm signals and instruct them on the
proper reaction to alarm signals.

• In rare instances, the sounding of a warning device can
cause temporary or permanent hearing loss.

A fire alarm system will not operate without any electrical
power. If AC power fails, the system will operate from standby
batteries only for a specified time and only if the batteries
have been properly maintained and replaced regularly.

Equipment used in the system may not be technically com­patible with the control. It is essential to use only equipment
listed for service with your control panel.

Telephone lines needed to transmit alarm signals from a
premise to a central monitoring station may be out of service
or temporarily disabled. For added protection against tele­phone line failure, backup radio transmission systems are rec­ommended.

The most common cause of fire alarm malfunction is inade­quate maintenance. To keep the entire fire alarm system in
excellent working order, ongoing maintenance is required per
the manufacturer's recommendations, and UL and NFPA stan­dards. At a minimum, the requirements of Chapter 7 of NFPA
72 shall be followed. Environments with large amounts of
dust, dirt or high air velocity require more frequent mainte­nance. A maintenance agreement should be arranged
through the local manufacturer's representative. Maintenance
should be scheduled monthly or as required by National and/
or local fire codes and should be performed by authorized pro­fessional fire alarm installers only. Adequate written records
of all inspections should be kept.

Precau-Lg.p65 01/18/2000

Installation Precautions

Adherence to the following will aid in problem-free
installation with long-term reliability:

WARNING - Several different sources of power can be con-
nected to the fire alarm control panel. Disconnect all sources

of power before servicing. Control unit and associated equip­ment may be damaged by removing and/or inserting cards,
modules, or interconnecting cables while the unit is energized.
Do not attempt to install, service, or operate this unit until this
manual is read and understood.

CAUTION - System Reacceptance Test after Software
Changes. To ensure proper system operation, this product

must be tested in accordance with NFPA 72 Chapter 7 after
any programming operation or change in site-specific soft­ware. Reacceptance testing is required after any change, ad­dition or deletion of system components, or after any modifica­tion, repair or adjustment to system hardware or wiring.

All components, circuits, system operations, or software func­tions known to be affected by a change must be 100% tested.
In addition, to ensure that other operations are not inadvert­ently affected, at least 10% of initiating devices that are not
directly affected by the change, up to a maximum of 50 de­vices, must also be tested and proper system operation veri­fied.

This system meets NFPA requirements for operation at
0-49° C/32-120° F
condensing) at 30° C/86° F. However, the useful life of the
system's standby batteries and the electronic components
may be adversely affected by extreme temperature ranges
and humidity. Therefore, it is recommended that this system
and all peripherals be installed in an environment with a nomi­nal room temperature of 15-27° C/60-80° F.

Verify that wire sizes are adequate for all initiating and
indicating device loops. Most devices cannot tolerate more
than a 10% I.R. drop from the specified device voltage.

and at a relative humidity of 85% RH (non-

Like all solid state electronic devices, this system may
operate erratically or can be damaged when subjected to light­ning-induced transients. Although no system is completely
immune from lightning transients and interferences, proper
grounding will reduce susceptibility. Overhead or outside

aerial wiring is not recommended, due to an increased sus­ceptibility to nearby lightning strikes. Consult with the Techni-

cal Services Department if any problems are anticipated or
encountered.

Disconnect AC power and batteries prior to removing or in­serting circuit boards. Failure to do so can damage circuits.

Remove all electronic assemblies prior to any drilling, filing,
reaming, or punching of the enclosure. When possible, make
all cable entries from the sides or rear. Before making modifi­cations, verify that they will not interfere with battery, trans­former, and printed circuit board location.

Do not tighten screw terminals more than 9 in-lbs.
Over-tightening may damage threads, resulting in reduced
terminal contact pressure and difficulty with screw terminal
removal.

Though designed to last many years, system components
can fail at any time. This system contains static-sensitive
components. Always ground yourself with a proper wrist strap
before handling any circuits so that static charges are re­moved from the body. Use static-suppressive packaging
to protect electronic assemblies removed from the unit.

Follow the instructions in the installation, operating, and
programming manuals. These instructions must be followed
to avoid damage to the control panel and associated
equipment. FACP operation and reliability depend upon
proper installation by authorized personnel.

FCC Warning

WARNING: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used

in accordance with the instruction manual, may cause interference to radio communications. It has been tested and
found to comply with the limits for class A computing device pursuant to Subpart B of Part 15 of FCC Rules, which
is designed to provide reasonable protection against such interference when operated in a commercial environ­ment.
Operation of this equipment in a residential area is likely to cause interference, in which case the user will be re­quired to correct the interference at his own expense.

Precau-Lg.p65 01/18/2000

Notes

4

Document #15140 Rev.G 01/02/02 P/N 15140:G

Table of Contents

CHAPTER 1: Product Description .........................................................................................................................10

1.1: Product Features..........................................................................................................................................10

FIGURE 1-1: Optional DP-5024UD....................................................................................................11

FIGURE 1-2: MS-5024UD Panel........................................................................................................12

1.2: Controls and Indicators ...............................................................................................................................13

FIGURE 1-3: Controls and Indicators .................................................................................................13

1.3: Circuits ........................................................................................................................................................13

1.4: Digital Communicator.................................................................................................................................14

1.5: Components.................................................................................................................................................14

1.5.1: Main Circuit Board ...........................................................................................................................14

1.5.2: Cabinet ..............................................................................................................................................14

1.5.3: Transformer Assembly......................................................................................................................15

FIGURE 1-4: XRM-24(E) Transformer ..............................................................................................15

1.5.4: Batteries ............................................................................................................................................15

1.6: Optional Devices .........................................................................................................................................15

1.6.1: RM-5F Five-Zone Relay Module .....................................................................................................15

1.6.2: CAC-5F Class A Converter Module.................................................................................................15

1.6.3: ADM-24 Annunciator Driver Module ..............................................................................................15

1.6.4: RZA-5F Remote Annunciator...........................................................................................................15

1.6.5: PRT-24 Printer Interface Module......................................................................................................16

1.6.6: DP-5024UD Dress Panel ..................................................................................................................16

1.6.7: BB-17F Battery Box .........................................................................................................................16

1.6.8: PK-5024UD Programming Kit .........................................................................................................16

1.7: Specifications ..............................................................................................................................................16

1.8: Telephone Requirements and Warnings ......................................................................................................18

1.8.1: Telephone Circuitry...........................................................................................................................18

1.8.2: Digital Communicator.......................................................................................................................18

1.8.3: Telephone Company Rights and Warnings .......................................................................................18

CHAPTER 2: Installation.........................................................................................................................................19

2.1: Mounting Options ......................................................................................................................................19

FIGURE 2-1: MS-5024UD Cabinet ....................................................................................................19

2.2: Backbox Mounting......................................................................................................................................19

FIGURE 2-2: Cabinet Dimensions and Knockout Locations ..............................................................20

FIGURE 2-3: Backbox and Battery Box .............................................................................................21

2.3: Operating Power..........................................................................................................................................22

FIGURE 2-4: Operating Power Connections.......................................................................................22

2.4: Input Circuits...............................................................................................................................................23

FIGURE 2-5: Typical Initiating Device Circuit Connections .............................................................23

2.5: Output Circuits ............................................................................................................................................24

FIGURE 2-6: Auxiliary Power Connections .......................................................................................24

FIGURE 2-7: Notification Appliance Circuit Connections .................................................................24

FIGURE 2-8: Auxiliary Relay and Relay Driver Terminals ...............................................................25

2.6: UL Power-limited Wiring Requirements ....................................................................................................26

FIGURE 2-9: Typical Wiring Diagram for UL Power-limited Requirements ....................................26

2.7: Digital Communicator.................................................................................................................................27

FIGURE 2-10: Wiring Phone Jacks.....................................................................................................27

2.8: Optional Boards...........................................................................................................................................28

2.8.1: ADM-24 Annunciator Driver Module ..............................................................................................28

FIGURE 2-11: ADM-24 Annunciator Driver Module ........................................................................28

2.8.2: RZA-5F Remote Annunciator ..........................................................................................................28

FIGURE 2-12: RZA-5F .......................................................................................................................28

Document 15140 Rev. G 01/02/02 P/N: 15140:G 5

Table of Contents

FIGURE 2-13: Wiring the RZA-5F/ADM-24 .....................................................................................29

FIGURE 2-14: Installing the Annunciator (Single-Gang Electrical Box) ...........................................29

2.8.3: PRT-24 Printer Interface Module......................................................................................................30

FIGURE 2-15: Remote Printer Connections........................................................................................30

2.8.4: RM-5F Five-Zone Relay Module......................................................................................................31

FIGURE 2-16: RM-5F Installation and Wiring ...................................................................................31

2.8.5: CAC-5F Class A Converter Module .................................................................................................32

FIGURE 2-17: CAC-5F Style D Converter .........................................................................................32

CHAPTER 3: Programming Instructions...............................................................................................................33

3.1: Entering Program Mode ..............................................................................................................................33

3.2: Switch Functions .........................................................................................................................................34

FIGURE 3-1: Control Panel Keypad ...................................................................................................34

3.3: Programming Options .................................................................................................................................34

TABLE 3-1: Primary Event Codes - 3+1, 4+1 Express, 4+1 Standard, Expanded & 4+2 Expanded .36

TABLE 3-2: Primary Event Codes - 4+2 Standard and 4+2 Express..................................................37

TABLE 3-3: Event Codes, Primary Central Station Number..............................................................38

TABLE 3-4: Secondary Event Codes-3+1, 4+1 Express, 4+1 Standard, Expanded & 4+2 Expanded41

TABLE 3-5: Secondary Event Codes - 4+2 Standard and 4+2 Express..............................................42

TABLE 3-6: Event Codes, Secondary Central Station Number ..........................................................43

FIGURE 3-2: Verification Timing Diagram........................................................................................44

TABLE 3-7: Zone Function Selection .................................................................................................45

3.4: Default Programming ..................................................................................................................................49

CHAPTER 4: Operating Instructions ....................................................................................................................50

4.1: Switches in Normal Mode...........................................................................................................................50

4.1.1: RESET...............................................................................................................................................50

4.2: Displays .......................................................................................................................................................51

FIGURE 4-1: Phone Connectors and LEDs.........................................................................................52

4.3: Operation .....................................................................................................................................................53

4.3.1: Alarm Response ................................................................................................................................53

4.3.2: Alarm Restoral ..................................................................................................................................54

4.3.3: System Supervisory Condition Response .........................................................................................54

4.3.4: System Supervisory Restoral Response ............................................................................................54

4.3.5: Trouble Condition Response .............................................................................................................55

4.3.6: Trouble Condition Restoral...............................................................................................................55

4.3.7: Off Normal Reporting .......................................................................................................................55

4.3.8: Zone Disable/Enable .........................................................................................................................56

4.3.9: Fire Drill............................................................................................................................................56

4.4: Central Station Communications.................................................................................................................57

TABLE 4-1: Format Selection Address (16 & 42) ..............................................................................58

TABLE 4-2: Format Selection Address Explanation...........................................................................59

4.4.1: Transmittal Priorities.........................................................................................................................60

TABLE 4-3: Compatible UL Listed Receivers....................................................................................61

CHAPTER 5: Servicing............................................................................................................................................62

5.1: Walktest Mode.............................................................................................................................................62

5.2: History Mode...............................................................................................................................................63

5.3: Troubleshoot Mode......................................................................................................................................64

5.3.1: Zone Voltages ....................................................................................................................................64

TABLE 5-1: Nominal Zone Voltages..................................................................................................64

5.3.2: AC Line Voltage................................................................................................................................65

5.3.3: Battery Voltage ..................................................................................................................................65

5.3.4: Telephone Lines ................................................................................................................................65

FIGURE 5-1: Phone Connectors and LEDs.........................................................................................65

TABLE 5-2: AC Line Voltage Range..................................................................................................65

6

Document 15140 Rev. G 01/02/02 P/N: 15140:G

Table of Contents

TABLE 5-3: Battery Voltage...............................................................................................................65

5.3.5: NAC 1 & 2 ........................................................................................................................................66

5.3.6: Resettable Power...............................................................................................................................66

5.4: Lamp Test ....................................................................................................................................................66

5.5: Print Mode...................................................................................................................................................66

CHAPTER 6: Slave Communicator Configuration ...............................................................................................67

FIGURE 6-1: Slave Communicator Connections...............................................................................68

CHAPTER 7: Remote Site Upload/Download .......................................................................................................69

7.1: Downloading Program ................................................................................................................................69

7.1.1: Security Features...............................................................................................................................70

7.2: Downloading Initiated at Control Panel......................................................................................................71

7.3: Downloading Initiated at a Service Terminal..............................................................................................71

7.4: Uploading Initiated at a Service Terminal...................................................................................................72

Appendix A: Battery Calculations .......................................................................................................................73

TABLE A-1: Battery Calculations ......................................................................................................73

A.1: The Main Power Supply ............................................................................................................................74

TABLE A-2: Filtered Load in Standby - external devices connected to TB4 only ............................74

TABLE A-3: Filtered Load in Alarm .................................................................................................75

Appendix B: Programming Reference Sheets .....................................................................................................76

Appendix C: Operation and Function Modes .....................................................................................................82

C.1: Operation Modes .......................................................................................................................................82

C.2: Function Modes ........................................................................................................................................82

TABLE C-1: Operation Modes ...........................................................................................................82

TABLE C-2: Function Modes .............................................................................................................82

Appendix D: Ademco Contact ID Format Event Code Descriptions ...............................................................83

Document 15140 Rev. G 01/02/02 P/N: 15140:G 7

This control panel has been designed to comply with standards set forth by the following regulatory agencies:

• Underwriters Laboratories Standard UL 864

• NFPA 72 National Fire Alarm Code for Local, Remote Station and Central Station Fire Alarm System

Before proceeding, the installer should be familiar with the following documents.

NFPA Standards

This Fire Alarm Control Panel complies with the following NFPA Standards:

NFPA 72 National Fire Alarm Code for Central Station Fire Alarm Systems Protected Premises Unit
(Automatic, Manual and Waterflow), Local Fire Alarm Systems (Automatic, Manual, Waterflow and
Sprinkler Supervisory), Auxiliary Protective Fire Alarm Systems (Automatic, Manual and Water­flow), Proprietary Protective Fire Alarm Systems (Automatic, Manual and Waterflow) and Remote
Station Fire Alarm Systems (Automatic, Manual and Waterflow).

Underwriters Laboratories Documents:

UL 38 Manually Actuated Signaling Boxes

UL 217 Smoke Detectors, Single and Multiple Station

UL 228 Door Closers–Holders for Fire Protective Signaling Systems

UL 268 Smoke Detectors for Fire Protective Signaling Systems

UL 268A Smoke Detectors for Duct Applications

UL 346 Waterflow Indicators for Fire Protective Signaling Systems

UL 464 Audible Signaling Appliances

UL 521 Heat Detectors for Fire Protective Signaling Systems

UL 864 Standard for Control Units for Fire Protective Signaling Systems

UL 1481 Power Supplies for Fire Protective Signaling Systems

UL 1638 Visual Signaling Appliances

UL 1971 Signaling Devices for Hearing Impaired

Other:

NEC Article 250 Grounding

NEC Article 300 Wiring Methods

NEC Article 760 Fire Protective Signaling Systems

Applicable Local and State Building Codes

Requirements of the Local Authority Having Jurisdiction (LAHJ)

Fire•Lite Documents

Fire•Lite Device Compatibility Document Document #15384

8

Document #15140 Rev.G 01/02/02 P/N 15140:G

MS-5024UD Main Circuit Board

Document #15140 Rev.G 01/02/02 P/N 15140:G

9

Product Description

CHAPTER 1 Product Description

The MS-5024UD is a combination FACP (Fire Alarm Control Panel) and DACT (Digital Alarm Communicator
Transmitter) all on one circuit board. It is a five-zone panel which uses conventional input devices. The panel
accepts waterflow devices, two-wire smoke detectors, four-wire smoke detectors, pull stations and other normally
open contact devices. Outputs include two NACs (Notification Appliance Circuits), alarm and trouble relays, super­visory and communicator failure relay drivers.

The integral communicator transmits system status (alarms, troubles, AC loss, etc.) to UL-listed Central Stations via
the public switched telephone network. The control panel has a built-in programmer and may also serve as a slave
communicator to a host panel. It also supervises all wiring, AC voltage, telephone line input voltage and battery
level.

The control panel may be programmed or interrogated off-site via the public switched telephone network. Any IBM

™

compatible personal computer with DOS

4.01 or greater plus Windows™ 3.1 or greater, with a 1200 baud Hayes™
compatible modem and Fire•Lite Upload/Download software P/N PK-5024UD, may serve as a Service Terminal.
This allows download of the entire program or upload of the entire program, history file, walktest data, current status
and system voltages. The MS-5024UDE offers the same features as the MS-5024UD but allows connection to 220/
240 VAC input.

1.1 Product Features

• Selectable as Fire Panel, Fire Panel/Communicator or Slave Communicator

• Programmable Zone ID: 2-wire smoke, pull station, normally open contact device, supervisory, supervisory
autosilence, waterflow silenceable or waterflow nonsilenceable

• One Style D (Class A) zone

• Four Style B (Class B) zones

• 3.6 amps usable power expandable to 5.6 amps

• Optional 5-zone Relay Module (RM-5F)

• CAC-5F Style D (Class A) Zone Converter Module

• Two NFPA Style Y (Class B) or Style Z (Class A) Notification Appliance (bell) Circuits

• Built-in programmer

• Built-in voltmeter

• Telephone Line Active LED indicators

• Communication confirmation (Kissoff) LED

• Disable report by event

• Programmable event codes

• 24 volt operation

• Real-Time clock and calendar

• Trouble reminder

• Alarm verification

• RZA-5F remote annunciator (requires ADM-24 Annunciator Driver Module)

• Small size - 15" (38.1 cm) x 14.5" (36.83 cm) x 2.75" (6.985 cm)

• History file with 32 event storage

• Silence inhibit per NAC (Notification Appliance Circuit)

• Autosilence per NAC

10

Document #15140 Rev.G 01/02/02 P/N 15140:G

Product Features

A

• Touchtone/Rotary dialing

• Programmable make/break ratio

• Fuseless design

• PRT-24 (Printer Interface Module)

• Print real-time system status

• Print history and walktest files, program contents and troubleshoot mode voltages

• PK-5024UD Upload/Download Software Kit

• Number of dial attempts (minimum of 5 and maximum of 10)

• Programmable channel ID (slave)

• Programmable zone delay (waterflow only)

• Form-C alarm and trouble relays

• Supervisory and communication fail relay drivers

• Low AC voltage sense

•One-man walktest

• Optional Dress Panel cover (DP-5024UD)

Optional DP-5024UD

FIRE CONTROL/COMMUNICATOR

AC POWER

ALARM

RESET

1

4

7

A

Note: Unless otherwise specified

FIGURE 1-1:

, MS-5024UD shall be used in this manual to refer to both the MS-5024UD and

MS-5024UDE Fire Alarm Control Communicators.

n

SILENCE

2

3

5

6

8

9

0

B

TROUBLE

SUPERVISORY

MODE

F

E

1ST

D

EVENT

ENTER

C

STORE

Document #15140 Rev.G 01/02/02 P/N 15140:G

11

Product Features

FIGURE 1-2:

MS-5024UD Panel

Notification Appliance
Circuits

Standard
Transformer

Four Character
7-Segment LED
Display

Keypad

Optional
Transformer

Alarm &
Trouble
Relays

5 Input
Zones

Primary & Secondary Phone Lines

Annunciator
Driver Module
Interface
Connector

Relay Module
Interface
Connector

PROM U23

Piezo 85dB

1

Printer
Interface
Module

Connector
Holds up to 7 AH Batteries
Up to 60 Hrs. of Standby

Software for the Fire Alarm Control Communicator is located in a PROM inserted in the IC socket labeled

1.

U23. The MS-5024UD and MS-5024UDE each contain unique software. For specific panel software infor­mation, refer to the MS-5024UD(E) Field Software Change Procedure Document #50125.

12

Document #15140 Rev.G 01/02/02 P/N 15140:G

Controls and Indicators

1.2 Controls and Indicators

Front Panel Switches

RESET Digits 0-9

SILENCE A

MODE B

Up Arrow C

Down Arrow D

1st EVENT E

ENTER/STORE F

Displays

• Alarm - red LED

• Trouble - yellow LED

• Supervisory - yellow LED

• AC Power - green LED

• Four 7-Segment Displays - red

• Primary Phone Line Active - red LED

• Secondary Phone Line Active - red LED

• 'Kissoff' Signal from Central Station - green LED

• Silence - yellow LED

• Modem - green LED

FIGURE 1-3:

Controls and Indicators

Local Piezo Sounder

A piezo sounder provides separate and distinct sounds for alarm, trouble and supervisory conditions.

1.3 Circuits

Input Circuits

Five input circuits provide Style B configuration with one circuit also configurable for Style D. Input circuits may be
used as standard fire control panel zones or slave communicator input channels.

• Initiating Device Circuit 1 (Style B) accepts normally open contact devices and 2-wire smoke detectors

• Initiating Device Circuit 2 (Style B) accepts normally open contact devices and 2-wire smoke detectors

• Initiating Device Circuit 3 (Style B/D) accepts normally open contact devices, 2-wire smoke detectors and
waterflow devices

• Initiating Device Circuit 4 (Style B) accepts normally open contact devices and 2-wire smoke detectors

• Initiating Device Circuit 5 (Style B) accepts normally open contact devices and 2-wire smoke detectors

Output Circuits

• 24 Volt Resettable Power Output

• 24 Volt Nonresettable Power Output

• Primary Telephone Line

• Secondary Telephone Line

• 24 Volt Battery Charger

•Printer Port

Document #15140 Rev.G 01/02/02 P/N 15140:G

13

Digital Communicator

Notification Appliance Circuits

Two Notification Appliance Circuits configurable for Style Y (Class B) or Style Z (Class A) with various program­mable features.

Relays

Two dry Form-C relay contacts for system alarm and system trouble are provided. Contacts are rated 2 amps @ 30
VDC and 0.5 amps @ 30 VAC resistive.

Relay Drivers

Two relay driver outputs for supervisory and communication failure are available.

1.4 Digital Communicator

Two modular phone jacks allow easy connection to telephone lines. Modular jacks are labeled PH1 and PH2 for the
Primary and Secondary phone lines. Telephone line active red LEDs are provided as well as a green 'kissoff' LED.
The integral digital communicator provides the following functions:

• Line Seizure - takes control of the phone lines disconnecting any premises phones

• Off/On Hook - perform on and off-hook status to the phone lines

• Listen for dial tone - 440 hertz tone typical in most networks

• Dialing the Central Station(s) phone number - default is Touch-Tone

• For tone burst or touchtone type formats: Discern proper 'Ack' and 'kissoff' tone(s). The frequency and time
duration of the tone(s) varies with the transmission format. The control panel will adjust accordingly

• Communicate in the following formats:

✓

12 Tone Burst Types (20 pps):

(3+1, 4+1, 3+1 Expanded, 4+1 Expanded and 4+2 Expanded)

✓

3 Touchtone Types:

4+1 Ademco Express

4+2 Ademco Express

Ademco Contact ID

(see Table 4-3 for a list of compatible receivers)

®

, programmable to rotary

1.5 Components

1.5.1 Main Circuit Board

The main circuit board contains the system's CPU, power supply, other primary components and wiring interface
connectors. Optional modules plug in and are mounted to the main circuit board. The main circuit board is delivered
premounted in the cabinet.

1.5.2 Cabinet

The cabinet is red with an attractive navy blue front overlay. The backbox measures 15" (38.1 cm) x 14.5" (36.83
cm) x 2.75" (6.985 cm) and provides space for two batteries (up to 7 Amp Hours). Also available is an optional dress
panel (DP-5024UD), which mounts inside the cabinet.

14

Document #15140 Rev.G 01/02/02 P/N 15140:G

Optional Devices

1.5.3 Transformer Assembly

FIGURE 1-4:

XRM-24(E) Transformer

One 100VA transformer is provided standard with the panel (3.6 amps
maximum). An optional 100VA transformer, XRM-24 (XRM-24E for
MS-5024UDE), is available to provide maximum accessory power (6.6

Standard

Transformer

amps maximum).

1.5.4 Batteries

The cabinet provides space for 7 Amp Hour batteries (for 12 Amp Hour
up to 18 Amp Hour batteries, use the listed BB-17F battery box). Batter­ies must be ordered separately.

Optional

Transformer

XRM-24(E)

1.6 Optional Devices

1.6.1 RM-5F Five-Zone Relay Module

The RM-5F option module provides five Form-C relays which track zones 1 through 5. The module mounts to con­nector J7 on the lower right side of the main circuit board. Refer to Figure 1-2, “MS-5024UD Panel,” on page 12 and
Figure 2-16 on page 31.

1.6.2 CAC-5F Class A Converter Module

The CAC-5F Class A Converter module converts the Style B (Class B) Initiating Device Circuits to Style D (Class
A). The CAC-5F mounts to terminal block TB2, located in the upper center of the main circuit board. The remov­able terminal block on the CAC-5F module provides for ease of wiring. Refer to Figure 2-17, “CAC-5F Style D Con­verter,” on page 32

1.6.3 ADM-24 Annunciator Driver Module

The ADM-24 Annunciator Driver Module supports the RZA-5F Remote Annunciator module. Annunciator wiring is
supervised for open circuits by this module. The Annunciator Driver Module mounts to connector J3 in the upper
right corner of the main circuit board. Refer to Figure 1-2, “MS-5024UD Panel,” on page 12 and Figure 2-11 on page

28.

1.6.4 RZA-5F Remote Annunciator

The RZA-5F Remote Annunciator mounts on a standard single-gang box and provides LED indication of the
following:

• Alarm Zone 1 (red)

• Alarm Zone 2 (red)

• Alarm Zone 3 (red)

• Alarm Zone 4 (red)

• Alarm Zone 5 (red)

• System Trouble (yellow)

A Local Trouble Sounder and Tone Silence Switch are also provided. All LEDs and their wiring are supervised for
open conditions. Any open condition will cause the System Trouble LED to illuminate. Slide-in paper labels permit
an easy change of zone information. Refer to Figure 2-12, “RZA-5F,” on page 28, Figure 2-13 on page 29 and Figure
2-14 on page 29. Note that the Remote Annunciator requires the use of the ADM-24 Annunciator Driver Module.

Document #15140 Rev.G 01/02/02 P/N 15140:G

15

Specifications

1.6.5 PRT-24 Printer Interface Module

The Printer Interface Module may be used to connect a printer to the control panel for the purpose of printing a his­tory report, walktest file, troubleshoot report, program entries or current system status. Printers require separate
external primary power. Connect the PRT-24 module (with cable) to the serial EIA-232 port on the printer. The
module mounts to the J2 connector on the main circuit board. Note that an EDP listed printer must be used if the

printer will be permanently attached to the control panel. Refer to Figure 2-15, “Remote Printer Connections,” on
page 30.

1.6.6 DP-5024UD Dress Panel

A red dress panel is available as an option. The dress panel restricts access to the system wiring while allowing
access to the membrane switch panel. Refer to Figure 1-1, “Optional DP-5024UD,” on page 11.

1.6.7 BB-17F Battery Box

The BB-17F battery box may be used to house two batteries, from 12 Amp Hour to 18 Amp Hour. The battery box
mounts directly below the cabinet and main circuit board. Refer to Figure 2-3, “Backbox and Battery Box,” on page

21. The BB-17F is red and is provided with knockouts.

1.6.8 PK-5024UD Programming Kit

This kit includes one 3½" diskette plus Instruction Manual P/N 50041. When the software is loaded into an IBM
compatible computer, it creates an off-line Service Terminal that allows any MS-5024UD panel to be uploaded or
downloaded over standard telephone lines.

1.7 Specifications

AC Power - TB1

MS-5024UD: 120 VAC, 60 Hz, 2.3 amps
MS-5024UDE: 220/240 VAC, 50 Hz, 1.2 amps
Wire size: minimum #14 AWG (2 mm

Battery (lead acid only) - J1

Maximum Charging Circuit: Normal Flat Charge - 27.6V @ 0.8 amp
Maximum Charger Capacity: 17 Amp Hour battery. (MS-5024UD cabinet holds maximum 7 Amp Hour battery.
Larger batteries require Fire•Lite BB-17F or other UL listed battery cabinet).

Initiating Device Circuits - TB2

Detector Zones 1, 2, 3, 4, 5 Power-limited Circuitry
Operation: All zones are NFPA Style B, Zone 3 is NFPA Style B or Style D. Use CAC-5F module for Style D
operations
Normal Operating Voltage: 24 VDC (ripple = 100 mV maximum)
Alarm Current: 26 mA Short Circuit Current: 42 mA maximum
Maximum Loop Resistance: 100 ohms
End-of-Line Resistor: 4.7K ohms, ½ watt (P/N 27072 UL listed)

Detector Loop Current is sufficient to ensure operation of one alarmed detector per zone

Standby Current: 7.26 mA (includes ELR and 2 mA maximum detector current)
Smoke Detector Identifier A
Refer to Fire•Lite Device Compatibility Document for listed compatible devices

2

) with 600V insulation

16

Document #15140 Rev.G 01/02/02 P/N 15140:G

Specifications

Notification Appliance Circuits - TB5 & TB6

Nonregulated, special purpose power, Styles Y and Z supported
Power-limited circuitry
Operating Voltage: Nominal 24 volts
Current for all external devices: 3.0 amps expandable to 5.6 amps
Current-limit: PTC
Maximum signaling current/circuit: 2.5 amps
End-of-Line resistor: 4.7K ohms, ½ watt (P/N 71252 UL listed) for NACs
Refer to Fire•Lite Device Compatibility Document for listed compatible devices

Alarm and Trouble Relays - TB3

Contact rating: 2.0 amps @ 30 VDC (resistive), 0.5 amps @ 30 VAC (resistive)
Alarm and Trouble: Form-C power-limited circuitry (see Figure 2-7 note for power-limited wiring application)

Auxiliary Outputs - TB4, Terminals 5 & 6

TB4-5 Supervisory Relay Driver: Normally high, active low, sinks up to 40 mA
TB4-6 Communication Failure: Normally high, active low, sinks up to 40 mA
Power-limited circuitry

Four-wire Smoke Detector Power - TB4, Terminals 3(+) & 4(-)

Maximum ripple voltage: 10 mV

RMS

Operating voltage: Nominal 24 volts
Up to 300 mA is available for powering 4-wire smoke detectors
Power-limited circuitry
Recommended maximum standby current is 50 mA (see Battery Calculations in Appendix A)
Refer to Fire•Lite Device Compatibility Document for compatible listed devices

Nonresettable Filtered 24V Power - TB4 Terminals 1(+) & 2(-)

Maximum ripple voltage: 10 mV

RMS

Operating voltage: Nominal 24 volts
Total DC current available from this output is up to 300 mA
Power-limited circuitry
Recommended maximum standby current is 150 mA (see Battery Calculations in Appendix A)
Refer to Fire•Lite Device Compatibility Document for compatible listed devices

Notes:

For power supply calculations, refer to Appendix A.

1.

Total current for nonresettable power, 4-wire smoke detector power and two Notification Appliance Circuits

2.

must not exceed 5.6 amps. Total external system current in excess of 3.6 amps requires the XRM-24 Trans­former (XRM-24E for 220/240 VAC applications) and 12 Amp Hour or 17 Amp Hour batteries.

Document #15140 Rev.G 01/02/02 P/N 15140:G

17

Telephone Requirements and Warnings

1.8 Telephone Requirements and Warnings

1.8.1 Telephone Circuitry

Ringer Equivalence Number (REN) = 1.3B

AC Impedance: 10.0 Mega Ohm

Complies with FCC Part 68

Mates with RJ31X Male Connector

Supervision Threshold: less than 4.0 volts for 2 minutes

The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive
RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all
areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices that may be con­nected to the line as determined by the total RENs, contact the telephone company to determine the maximum REN
for the calling area.

1.8.2 Digital Communicator

Before connecting the control panel to the public switched telephone network, the installation of two RJ31X jacks is
necessary. The following information is provided if required by the local telephone company:

Manufacturer: Fire•Lite Alarms, Inc.

One Fire-Lite Place

Northford, CT 06472

Product Model Number: MS-5024UD

FCC Registration Number: 1W6USA-20004-AL-E

Ringer Equivalence 1.3B

Note: The FCC ID label is located on the inside of the control panel door

1.8.3 Telephone Company Rights and Warnings

The telephone company, under certain circumstances, may temporarily discontinue services and/or make changes in
its facilities, services, equipment or procedures which may affect the operation of this control panel. However, the
telephone company is required to give advance notice of such changes or interruptions.

If the control panel causes harm to the telephone network, the telephone company reserves the right to temporarily
discontinue service. Advance notification will be provided except in cases when advance notice is not practical. In
such cases, notification will be provided as soon as possible. The opportunity will be given to correct any problems
and to file a complaint.

DO NOT CONNECT THIS PRODUCT TO COIN TELEPHONE, GROUND START, OR PARTY LINE SERVICES.

When the control panel activates, premise phones will be disconnected

Two separate phone lines are required. Do not connect both telephone interfaces to the same telephone line.

The control panel must be connected to the public switched telephone network upstream of any private telephone sys­tem at the protected premises.

An FCC compliant telephone cord must be used with this equipment. This equipment is designed to be connected to
the telephone network or premises wiring using a compatible RJ31X male modular plug which is Part 68 compliant.

18

Document #15140 Rev.G 01/02/02 P/N 15140:G

Installation

CHAPTER 2 Installation

2.1 Mounting Options

FIGURE 2-1:

MS-5024UD Cabinet

The cabinet may be either surface mounted or semi-flush
mounted using the optional Trim Ring P/N: TR-1-R. The
door is removable during the installation period by opening
and lifting the door off the hinges. The cabinet mounts using
two key slots and two additional 0.25" (6.35 mm) diameter
holes located in the backbox. The key slots are located at the
top of the backbox and the two securing holes at the bottom.

Carefully unpack the system and check for shipping damage.
Mount the cabinet in a clean, dry, vibration-free area where
extreme temperatures are not encountered. The area should
be readily accessible with sufficient room to easily install and
maintain the panel. Locate the top of the cabinet approxi­mately five feet above the floor with the hinge mounting on
the left. Determine the number of conductors required for the
devices to be installed. Sufficient knockouts are provided for
wiring convenience. Select the appropriate knockout(s) and
pull the required conductors into the box. Note that there are
no knockouts on the left (hinged) side of the cabinet. All wir­ing should be in accordance with the National and/or Local codes for fire alarm systems.

2.2 Backbox Mounting

✓

Open the door and lift the door off the pin hinges

✓

Remove the main PC board assembly by unscrewing the four screws in the corners of the board. Two
standoffs support the board in the center. Set the board aside in a safe, clean place. Avoid static dis­charge which may damage the board.

✓

Mark and predrill holes for the top two keyhole mounting bolts using the dimensions shown

✓

Install two upper fasteners in the wall with the screw heads protruding

✓

Using the proper 'keyholes', mount the backbox over the two screws

✓

Mark and drill the lower two holes

✓

Mount backbox, install remaining fasteners and tighten

✓

When the location is dry and free of construction dust, reinstall the main PC board

Document #15140 Rev.G 01/02/02 P/N 15140:G

19

Backbox Mounting

FIGURE 2-2:

Height=15.000”

(38.10 cm)

Cabinet Dimensions and Knockout Locations

2.875” (7.3 cm)

Draw wires through the respective knockout locations.

Backbox = 14.5”

(36.8 cm)

0.75”(1.9 cm)

9.1” (23.1 cm)

10.375”

(26.35 cm)

Top

Depth = 3.000”

(7.62 cm)

2.7”

(6.86cm)

Bottom

TR-1-R Trim Ring

Backbox Mounting Holes

ms2-4cab.cdr

1.125” (2.868 cm)

20

Document #15140 Rev.G 01/02/02 P/N 15140:G

Backbox Mounting

FIGURE 2-3:

Door = 15.342“ (38.97 cm)

Backbox and Battery Box

To p

Door = 14.677 “ (37.28 cm)

Depth = 2.875" (7.3 cm)

Depth = 3.050“

(7.75 cm)

Bottom

Depth = 4.75
(12.065 cm)

Battery Box = 8.5“ (21.59 cm)

Battery Box = 14.5“
(37.384 cm)

Notes:

Mount the Fire Alarm Control Communicator cabinet to the wall

1.

Remove knockouts on bottom of FACP cabinet and top of BB-17F

2.

Using conduit, hang the BB-17F from the Fire Alarm Control Communicator cabinet, making sure there is at

3.

least ½" of clearance between the two cabinets

Anchor the BB-17F to the wall

4.

Document #15140 Rev.G 01/02/02 P/N 15140:G

21

Operating Power

2.3 Operating Power

!

CAUTION: Several different sources of power can be connected to this panel. Disconnect all sources of power
before servicing. The panel and associated equipment may be damaged by removing and/or inserting cards, modules
or interconnecting cables while this unit is energized.

Primary Power Source (AC) and Earth Ground Connections

AC power connections are made inside the control panel cabinet. The primary power source for the MS-5024UD is
120 VAC, 60 Hz, 2.3 amps and for the MS-5024UDE is 220/240 VAC, 50 HZ, 1.2 amps. Run a pair of wires (with
ground conductor) from the protected premises main breaker box to TB1 of the main circuit board. As per the
National Electric Code, use 14 AWG (2.00 mm
may be connected to this circuit. In addition, this circuit must be provided with overcurrent protection and may not
contain any power disconnect devices. A separate Earth Ground connection must be made to ensure proper panel
operation and lightning and transient protection. Connect the Earth Ground wire [minimum 14 AWG (2.00 mm
one of the transformer mounting studs. Note: Do not use conduit for the Earth Ground connection since this does not

provide reliable protection.

Secondary Power Source (Batteries)

Observe polarity when connecting the battery. Connect the battery cable to J1 on the main circuit board using the
plug-in connector provided. The battery charger is current-limited and capable of recharging sealed lead acid type
batteries. The charger shuts off when the system is in alarm or if the battery voltage drops too low (below 17.4
VDC). See Appendix A for calculation of the correct battery rating.

2

) or heavier gauge wire with 600V insulation. No other equipment

2

)] to

CAUTION: Battery contains sulfuric acid which can cause severe burns to the skin and eyes, and can destroy fab-

!

rics. If contact is made with sulfuric acid, immediately flush the skin or eyes with water for 15 minutes and seek
immediate medical attention.

FIGURE 2-4:

Connect Earth Ground Wire

Operating Power Connections

22

Document #15140 Rev.G 01/02/02 P/N 15140:G

Input Circuits

2.4 Input Circuits

The control panel has five zone input circuits. The maximum loop resistance limit for each is 100 ohms. All field
wiring of each zone is supervised for opens and ground faults. Both conditions are visually and audibly annunciated
as well as communicated to a Central Station.

Each zone is a Style B Initiating Device Circuit (IDC) designed to accept any normally open contact device and con­ventional 2-wire, 24 volt smoke detectors. Each zone is power-limited to 7.26 mA in standby and 42 mA in alarm.
Zone 3 may also be configured as a Style D Initiating Device Circuit.

Note: All five initiating zones may be converted to Style D (Class A) by using a CAC-5F Class A Converter module.
Refer to Figure 2-17, “CAC-5F Style D Converter,” on page 32.

Zones 1-5 may be programmed as listed below. The factory default is 2-wire smoke detector for all zones:

• 2-wire smoke detector (factory default)

• Pull station

• Normally open contact device(s)

• Supervisory

• Supervisory, autoresettable

Zone 3 may also be programmed as:

• Waterflow, silenceable

• Waterflow, nonsilenceable

Note: A maximum of five waterflow devices may be used on zone 3 per NFPA 72.

Four-wire smoke detectors may be connected to any zone. Resettable power is provided via TB4, Terminals 3 and 4.

It is allowable to mix an assortment of device types (i.e. smoke detectors, heat detectors, pull stations, etc.) on any
zone. This is not recommended, however, since specific and detailed reports will not be possible. For example, the
report of general fire alarm versus pull station fire alarm or smoke detector fire alarm.

Refer to the Fire•Lite Device Compatibility Document for a list of compatible smoke detectors.

FIGURE 2-5:

UL listed compatible 2-wire smoke detector

Typical Initiating Device Circuit Connections

Style B Initiating Device Circuit
(supervised and power-limited)

4.7K ohm, ½ watt P/N 71252 UL listed

Manual Pull Station

Heat Detector

Style D Initiating Device Circuit
(supervised and power-limited)

UL listed compatible 2-wire smoke detector

Manual Pull Station

Heat Detector

MS-5024UD

Dummy load all unused circuits with 4.7K ohm

Document #15140 Rev.G 01/02/02 P/N 15140:G

ELR P/N 71245, across B+ and B-.

23

Output Circuits

2.5 Output Circuits

DC Power Output Connections

All DC power outputs are power-limited.

FIGURE 2-6:

Telephone Circuits

Provision to connect to two independent telephone lines is available via two telephone jacks labeled PH1 (primary)
and PH2 (secondary). Telephone line control/command is possible via double line seizure as well as usage of an
RJ31X style interconnection. Refer to Figure 2-10, “Wiring Phone Jacks,” on page 27.

Auxiliary Power Connections

Nonresettable Power (300 mA)

24 VDC filtered, nonresettable

power can be obtained from TB4,

Terminals 1(+) and 2(-)

+ - + -

1 2 3 4 5 6

TB4

4-Wire Smoke Detector Power (300 mA)

24 VDC filtered, resettable power for 4-wire

smoke detectors can be obtained from TB4,

Terminals 3(+) and 4(-)

Notification Appliance Circuits

The MS-5024UD provides two NACs (Notification Appliance Circuits) which can be configured as Style Y or Style
Z. Each circuit is capable of 2.5 amps of current. Total current drawn from these as will as other DC power outputs
cannot exceed 3.6 amps with the standard transformer, 5.6 amps if an optional XRM-24 transformer (XRM-24E for
the MS-5024UDE) is installed. Circuits are supervised and power-limited. Refer to the Fire•Lite Device Compatibil­ity Document for a listing of compatible notification appliances.

FIGURE 2-7:

Notification Appliance Circuit Connections

Style Y Notification Appliance Circuit (super-

vised and power-limited). 4.7K ohm, ½ watt

Polarized Bell

Polarized Strobe

Polarized Horn

P/N 71252 UL listed EOL resistor.

Polarized Bell

Polarized Horn

Polarized Horn

Note: Notification
Appliance Circuit
polarity shown in
alarm

state.

Dummy Load all
unused circuits
P/N 71245

Both Notification Appliance Circuits may be programmed as follows:

• Silenceable

• Nonsilenceable

• Enabled/disabled

• Silence inhibited

• Autosilence, 5 to 30 minutes

• Coded (March Time, Temporal or California)

24

Document #15140 Rev.G 01/02/02 P/N 15140:G

Output Circuits

Standard Relays

The control panel provides a set of Form-C alarm and a set of Form-C trouble contacts rated for 2.0 amps @ 30VDC
(resistive).

Relay Drivers

Relay driver outputs are provided for supervisory and communicator failure. These outputs can be used to drive UL
864 listed remote relays such as the MR-101C and MR-201C.

The control panel's open collector outputs on TB4, terminals 5 and 6 can be used to activate UL 864 listed relays.
Outputs are rated for 40 mA. The normal condition for each output is as shown below:

TB4-5 Supervisory Off (deenergized)

TB4-6 Communications Failure Off (deenergized)

Relays must be placed inside the cabinet or in a UL 864 recognized enclosure. Wiring from the control panel's termi­nals on TB4 to the relays must be less than 3 feet in length and enclosed in conduit. Wiring from the relay outputs
must remain in the same room as the location of the enclosure and be enclosed in conduit.

FIGURE 2-8:

Auxiliary Relay and Relay Driver Terminals

Relay Connections

Alarm

NO NC C NC NO C

1 2 3 4 5 6

T
B
3

Note: The alarm and trouble Form-C dry

contact relays must be power-limited cir­cuits. Any Form-C dry contact relay that

may be used must be wired from TB4 or a

UL listed power-limited power supply.

Trouble

All wiring to relay must

be in same room as
panel and in conduit

Relay Driver Connections

Relay energized LED

MR-201/C*

Relay energized LED

DPDT Contacts

10 Amps @ 115 VAC

Connections must be in

the same room as the

panel

DPDT Contacts

10 Amps @ 115 VAC

* The MR-101C and MR-201C include an enclosure.

Document #15140 Rev.G 01/02/02 P/N 15140:G

MR-101/C*

25

UL Power-limited Wiring Requirements

2.6 UL Power-limited Wiring Requirements

Power-limited and nonpower-limited circuit wiring must remain separated in the cabinet. All power-limited circuit
wiring must remain at least 0.25" (6.35 mm) away from any nonpower-limited circuit wiring. Furthermore, all
power-limited and nonpower-limited circuit wiring must enter and exit the cabinet through different knockouts and/or
conduits. A typical wiring diagram for the MS-5024UD is shown below. Refer to Figure 2-16, “RM-5F Installation
and Wiring,” on page 31 for additional information on wiring the RM-5F Relay module.

FIGURE 2-9:

Typical Wiring Diagram for UL Power-limited Requirements

Power-limited Circuits

Power-limited

Circuit

26

Nonpower-limited

Circuit

AC Power

Document #15140 Rev.G 01/02/02 P/N 15140:G

Digital Communicator

2.7 Digital Communicator

Two independent telephone lines can be connected to the control panel. Telephone line control/command is made
possible via double line seizure as well as usage of an RJ31X style interconnection. Note that it is critical that the

panel's digital communicator be located as the first device on the incoming telephone circuit to properly function.

The control panel's digital communicator is built into the main circuit board. Connection and wiring of two phone
lines is required as shown below.

FIGURE 2-10:

Wiring Phone Jacks

Document #15140 Rev.G 01/02/02 P/N 15140:G

27

Optional Boards

2.8 Optional Boards

2.8.1 ADM-24 Annunciator Driver Module

The Annunciator Driver Module supports the RZA-5F Remote Annunciator. Annunciator wiring is supervised for
open conditions by this module. The Annunciator Driver Module mounts to J3 in the upper right corner of the main
circuit board.

FIGURE 2-11:

ADM-24 Annunciator Driver Module

Main Circuit Board

2.8.2 RZA-5F Remote Annunciator

The RZA-5F mounts on a standard single-gang electrical box and
provides LED indication of the following:

Alarm Zone 1 (red)

Alarm Zone 2 (red)

Alarm Zone 3 (red)

Alarm Zone 4 (red)

Alarm Zone 5 (red)

System Trouble (yellow)

Connector located on

Standoff

FIGURE 2-12:

back of board

ADM-24

RZA-5F

The remote annunciator provides individual zone alarm LEDs, a
system trouble LED, a local piezo sounder and a remote sounder
shut off switch. All LEDs and their wiring are supervised for
open conditions. Any open condition will cause the System Trou­ble LED to turn on.

Note: The Remote Annunciator requires the use of an ADM-24
Annunciator Driver Module.

28

Document #15140 Rev.G 01/02/02 P/N 15140:G

Optional Boards

FIGURE 2-13:

Wiring the RZA-5F/ADM-24

ADM-24

+24V

Note: Make wiring connections with system

power off. Maximum wire impedance is 100

ohms per wiring connection.

RZA-5F

FIGURE 2-14:

Installing the Annunciator (Single-Gang Electrical Box)

screw #6-32 x 1.00” LG

Single-gang Box

RZA-5F

Document #15140 Rev.G 01/02/02 P/N 15140:G

29

Optional Boards

2.8.3 PRT-24 Printer Interface Module

A remote printer may be permanently or temporarily connected to provide a hardcopy printout of normal current sys­tem status and activity, program entries, history file, troubleshoot mode voltages and walktest data. The PRT-24 pro­vides an EIA-232 conversion to adapt to most 40 and 80 column printers.

CAUTION: DO NOT connect a printer to the Fire Alarm Control Communicator if a ground fault exists on the panel.
Circuit damage may result.

!

Installation

Remote printers require separate external primary power. Also required is the PRT-24 which includes the Printer
Interface Module and a 6 foot interface cable prewired to a DB25 connector. Connect the interface cable to the PRT­24 as shown in Figure 2-15. Insert the two supplied standoffs into mounting holes near the J2 connector on the main
circuit board. Connect the Printer Interface board to J2 on the main circuit board, press onto standoffs and connect
the attached cable to the serial EIA-232 port on the printer. The printer may be placed a maximum of 50 feet from the
panel. Note that a ground fault may occur on the control panel when this connection is made. For this reason, it is
important that there be no preexisting ground fault on the panel. For permanent printer connection, a ground fault is

not allowed.

Printer Configuration

The PRT-24 is required. Also refer to the documentation supplied with your printer. Set the printer's options as listed
in the table below.

FIGURE 2-15:

YELLOW

Remote Printer Connections

J1 located on back
of PRT-24 board

BLK

RED

GRN

Typical Printer Settings

Under the MENU area:

COMMUNICATION SETUP:
DATA BITS: 7
PARITY: EVEN
STOP BIT: 1 STOP
BAUD RATE: 2400

30

PRT-24 connection to main circuit board

DB-25P Front View

Document #15140 Rev.G 01/02/02 P/N 15140:G

Optional Boards

2.8.4 RM-5F Five-Zone Relay Module

The RM-5F option module provides five Form-C relays which track zones 1 through 5. The module mounts to con­nector J7 on the lower right side of the main circuit board as illustrated in Figure 2-16.

Nonpower-limited and power-limited wiring must have a minimum distance of 0.25" (6.35 mm) wire to wire. If this
module is used to drive nonpower-limited and power-limited circuits:

Skip a set of dry contacts to maintain the 0.25" (6.35mm) required space between power-limited and non-

1.

power-limited circuits. The wiring of this module must follow the requirements as specified above - OR

If this module is needed to drive power-limited and nonpower-limited relays that are next to each other, one

2.

relay must be used as an open circuit and the other as a closed circuit as shown in Figure 2-16.

FIGURE 2-16:

RM-5F Installation and Wiring

Connector located

on back of board

Main Circuit Board

Note: If relays are used as power-limited

circuits, paste supplied label to terminal

block as indicated below.

Power

Limited

RM-5F

Standoffs

Power-limited

Power-limited

Power-limited

No connection
No connection

Power-limited

Power-limited

Note: Zone Relay Contact Ratings - Maximum Switched Power is 150 watts or 1250 VA. Maximum Switched Current is 5 Amps
UL Rating: 5 Amps @ 30 VDC or 125 VAC, resistive. Contact Material: Silver Alloy

Document #15140 Rev.G 01/02/02 P/N 15140:G

31

Optional Boards

2.8.5 CAC-5F Class A Converter Module

The CAC-5F module converts the Style B (Class B) Initiating Device Circuits to Style D (Class A). The CAC-5F
mounts to terminal block TB2 located in the upper center of the main circuit board. Refer to Figure 2-17, “CAC-5F
Style D Converter,” on page 32. The removable terminal block on the CAC-5F module provides for ease of wiring.

FIGURE 2-17:

UL listed compatible 2-wire smoke detector

Insert two supplied standoffs into
CAC-5F circuit board, remove protec­tive paper from self-adhesive base of
standoff, install circuit board into TB2

of MS-5024UD and press to adhere

standoffs to cabinet.

CAC-5F Style D Converter

Manual Pull Station

Heat Detector

Waterflow Switch

Waterflow Switch

Waterflow Switch

Dummy load all unused circuits with 4.7K ohm

ELR P/N: 71245 across B+ and B-

CAC-5F Module

32

MS-5024UD Main Circuit Board

Notes:

Circuits 1 through 5 can accommodate 2-wire smoke detectors, plus any normally open contact device such as

1.

heat detectors or manual pull stations.

Only circuit 3 accommodates the nonsilenceable waterflow function.

2.

Document #15140 Rev.G 01/02/02 P/N 15140:G

Programming Instructions

CHAPTER 3 Programming Instructions

This chapter describes programming the panel from the onboard keyboard. Chapter 7 describes remote site upload/
download which includes programming the control panel on premises. Programming of the control panel is possible
at any time except when an alarm condition is present or during a fire drill.

The control panel has been designed for many different types of applications. After examining your specific applica­tion, review the programming options and choose the entries best suited for your system.

The control panel has a built-in intelligent programmer. All programming selections are stored in nonvolatile Electri­cally Erasable Programmable Read-Only Memory (EEPROM). This ensures that the control panel will remember all
entries made in programming mode even if both AC and battery power are removed. Invalid entries cause a 'beep'
from the onboard piezo sounder.

The user must program the primary and secondary phone numbers, account numbers and 24 hour test report times for
each Central Station account and the current time and date. The control panel comes with factory chosen options/fea­tures already programmed. Other options/features may be programmed if desired. If all factory default settings are
acceptable, programming is complete.

3.1 Entering Program Mode

To enter the Program Mode, press the MODE key once, (the display will go blank). You then have ten seconds to
start entering the Program Mode code 7764.

7764 spells PROG on a Touch-Tone

☛

If an incorrect key is entered, reenter the proper 4-digit code before pressing the [ENTER/STORE] key. Note that as
information is entered into the control panel, the digits will scroll across the display from right to left:

___7

__77

_776

7764

A pause of up to 10 seconds is allowed between each number while entering the code. After pressing the [ENTER/
STORE] key, the control panel will be in Program Mode and display 00_F. A maximum of 10 minutes of idle time

is allowed at this point before starting program entries, otherwise, the control panel will return to Normal Mode. A
maximum of 10 minutes is allowed between any key stroke. All entries made prior to the 10 minute time-out are
valid and will be stored.

Once in Program Mode, the control panel will:

• Blink the trouble LED

• Activate the trouble relay

• Disable the NACs (Notification Appliance Circuits)

• Disable the alarm relay

•Display 00_F

• Ignore all other keys other than those mentioned in this section

• Continue to communicate any events not previously acknowledged at a Central Station prior to entering
Program Mode

®

phone.

Document #15140 Rev.G 01/02/02 P/N 15140:G

33

Switch Functions

Note that address location 56 is factory defaulted to '0' for 'control panel only.' This keeps the communicator off until
location 56 is changed to '1' for 'slave communicator' or '2' for 'panel/communicator.' Once location 56 is set to '1' or
'2' and a valid phone number is entered, entry into the Program Mode will cause transmission of the 'system off nor­mal' report.

When viewing any address in Program Mode, the first three digits on the left of the display represent the memory
address which can be 00 to 374 (alpha-characters are not used). The last digit, farthest right, represents the contents
of the memory address. The first address and contents displayed upon entering Program Mode are shown below:

00_F

(address)(data)

3.2 Switch Functions

The function of each keypad key in Program Mode is shown below.

FIGURE 3-1:

No function in

Program Mode

Control Panel Keypad

Address entry keys are 0 - 9

Data entry keys are 0 - 9 and

A - F

Select operating mode

Increment memory address

Decrement memory address

One press = first memory address

Two presses = type any address

Save data, go to next address

3.3 Programming Options

Primary Central Station Phone Number (00-15)

The first sixteen addresses (00-15) are factory set to 'F' (00_F to 15_F). Programming this feature is typically done as
follows: If the phone number to be entered is 484-7161, press 4. The display will read 00_4. Press [ENTER/
STORE] to save the entry to memory and increment to the next address 01_F.

Enter the remaining numbers in their respective addresses as shown below:

Phone Number

Addresses

34

4847161FFFFFFFFF

00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15

Document #15140 Rev.G 01/02/02 P/N 15140:G

Programming Options

Valid entries for both the primary and secondary phone numbers are 0 - F with the numeric digits as dialed numbers
and the alpha-characters representing the following functions:

A = * on a Touchtone phone keypad

B = # on a Touchtone phone keypad

C = look for secondary dial tone for up to two seconds (then dial anyway)

D = 3-second pause

E = 5-second pause

F = end of phone number (Note: F must be entered)

Primary Central Station Number Communication Format (16)

One location is needed to select the Communication Format for the primary phone number. Address 16 is used for
this purpose. The default (factory setting) for this address is 'E' for Ademco Contact ID format. '0' through 'E' may be
entered in place of the default entry. After making the selection, press the [ENTER/STORE] key to store the selec­tion. The available format options are as follows:

0: 4+1 Ademco Express Standard, DTMF, 1400/2300 ACK

1: 4+2 Ademco Express Standard, DTMF, 1400/2300 ACK

2: 3+1 Standard 1800 Hz Carrier, 2300 Hz ACK

3: 3+1 Expanded 1800 Hz Carrier, 2300 Hz ACK

4: 3+1 Standard 1900 Hz Carrier, 1400 Hz ACK

5: 3+1 Expanded 1900 Hz Carrier, 1400 Hz ACK

6: 4+1 Standard 1800 Hz Carrier, 2300 Hz ACK

7: 4+1 Expanded 1800 Hz Carrier, 2300 Hz ACK

8: 4+1 Standard 1900 Hz Carrier, 1400 Hz ACK

9: 4+1 Expanded 1900 Hz Carrier, 1400 Hz ACK

A: 4+2 Standard 1800 Hz Carrier, 2300 Hz ACK

B: 4+2 Expanded 1800 Hz Carrier, 2300 Hz ACK

C: 4+2 Standard 1900 Hz Carrier, 1400 Hz ACK

D: 4+2 Expanded 1900 Hz Carrier, 1400 Hz ACK

E: Ademco Contact ID, DTMF, 1400/2300 ACK

F: Not Used

Note: Consult your Central Station for proper selection or consult our factory representatives. For any format cho­sen, the control panel automatically programs all of the event codes. Refer to Table 3-1 through Table 3-5 .

Document #15140 Rev.G 01/02/02 P/N 15140:G

35

Programming Options

3+1, 4+1 Express, 4+1 Standard and Expanded & 4+2 Expanded Formats

If '0, 2, 3, 4, 5, 6, 7, 8, 9, B or D' is entered for address 16, the following data is automatically programmed for the Pri­mary Central Station phone number event codes. Enter '0' for the Setting to disable the report.

TABLE 3-1:

Primary Event Codes - 3+1, 4+1 Express, 4+1 Standard, Expanded & 4+2 Expanded

Address Description Setting

127 Primary # Zone 1 Alarm Code 1
128 Primary # Zone 2 Alarm Code 1
129 Primary # Zone 3 Alarm Code 1
130 Primary # Zone 4 Alarm Code 1
131 Primary # Zone 5 Alarm Code 1
132 Primary # Zone 1 Disable Code F
133 Primary # Zone 2 Disable Code F
134 Primary # Zone 3 Disable Code F
135 Primary # Zone 4 Disable Code F
136 Primary # Zone 5 Disable Code F
137 Primary # Drill Code 9
138 Primary # AC Fault Code F
139 Primary # Zone 1 Fault Code F
140 Primary # Zone 2 Fault Code F
141 Primary # Zone 3 Fault Code F
142 Primary # Zone 4 Fault Code F
143 Primary # Zone 5 Fault Code F
144 Primary # Earth Fault Code F
145 Primary # Low Battery Fault Code F
146 Primary # No Battery Fault Code F
147 Primary # Telco Primary Line Fault Code F
148 Primary # Telco Secondary Line Fault Code F
149 Primary # NAC #1 Fault Code F
150 Primary # NAC #2 Fault Code F
151 Primary # Communication Trouble Primary # Code F
152 Primary # Communication Trouble Secondary # Code F
153 Primary # Annunciator Fault Code F
154 Primary # System Off Normal Code F
155 Primary # Zone 1 Alarm Restore Code E
156 Primary # Zone 2 Alarm Restore Code E
157 Primary # Zone 3 Alarm Restore Code E
158 Primary # Zone 4 Alarm Restore Code E
159 Primary # Zone 5 Alarm Restore Code E
160 Primary # Zone 1 Disable Restore Code E
161 Primary # Zone 2 Disable Restore Code E
162 Primary # Zone 3 Disable Restore Code E
163 Primary # Zone 4 Disable Restore Code E
164 Primary # Zone 5 Disable Restore Code E
165 Primary # Drill Restore Code 9
166 Primary # AC Fault Restore Code E
167 Primary # Zone 1 Fault Restore Code E
168 Primary # Zone 2 Fault Restore Code E
169 Primary # Zone 3 Fault Restore Code E
170 Primary # Zone 4 Fault Restore Code E
171 Primary # Zone 5 Fault Restore Code E
172 Primary # Earth Fault Restore Code E
173 Primary # Low Battery Fault Restore Code E
174 Primary # No Battery Fault Restore Code E
175 Primary # Telco Primary Line Fault Restore Code E
176 Primary # Telco Secondary Line Fault Restore Code E
177 Primary # NAC # 1 Fault Restore Code E
178 Primary # NAC # 2 Fault Restore Code E
179 Primary # Communication Trouble Primary # Restore Code E
180 Primary # Communication Trouble Secondary # Restore Code E
181 Primary # Annunciator Fault Restore Code E
182 Primary # System Off Normal Restore Code E
183 Primary # System Test Report 9
184 Primary # System Abnormal Test Report F
185 Primary # Request for Upload/Download 7
186 Primary # Successful Upload 7
187 Primary # Successful Download 7
188 Primary # Failed Upload/Download 7

36

Document #15140 Rev.G 01/02/02 P/N 15140:G

Programming Options

4+2 Standard and 4+2 Express Formats

If '1, A or C' is entered for address 16, the following data is automatically programmed for the Primary Central Sta­tion phone number event codes. Enter '00' for the Setting to disable the report.

TAB LE 3- 2:

Primary Event Codes - 4+2 Standard and 4+2 Express

Address Description Setting

127 - 128 Primary # Zone 1 Alarm Code 11
129 - 130 Primary # Zone 2 Alarm Code 12
131 - 132 Primary # Zone 3 Alarm Code 13
133 - 134 Primary # Zone 4 Alarm Code 14
135 - 136 Primary # Zone 5 Alarm Code 15
137 - 138 Primary # Zone 1 Disable Code F1
139 - 140 Primary # Zone 2 Disable Code F2
141 - 142 Primary # Zone 3 Disable Code F3
143 - 144 Primary # Zone 4 Disable Code F4
145 - 146 Primary # Zone 5 Disable Code F5
147 - 148 Primary # Drill Code 97
149 - 150 Primary # AC Fault Code F6
151 - 152 Primary # Zone 1 Fault Code F1
153 - 154 Primary # Zone 2 Fault Code F2
155 - 156 Primary # Zone 3 Fault Code F3
157 - 158 Primary # Zone 4 Fault Code F4
159 - 160 Primary # Zone 5 Fault Code F5
161 - 162 Primary # Earth Fault Code F7
163 - 164 Primary # Low Battery Fault Code F8
165 - 166 Primary # No Battery Fault Code F9
167 - 168 Primary # Telco Primary Line Fault Code FA
169 - 170 Primary # Telco Secondary Line Fault Code FB
171 - 172 Primary # NAC #1 Fault Code FC
173 - 174 Primary # NAC #2 Fault Code FC
175 - 176 Primary # Communication Trouble Primary # Code FD
177 - 178 Primary # Communication Trouble Secondary # Code FE
179 - 180 Primary # Annunciator Fault Code FC
181 - 182 Primary # System Off Normal Code FF
183 - 184 Primary # Zone 1 Alarm Restore Code E1
185 - 186 Primary # Zone 2 Alarm Restore Code E2
187 - 188 Primary # Zone 3 Alarm Restore Code E3
189 - 190 Primary # Zone 4 Alarm Restore Code E4
191 - 192 Primary # Zone 5 Alarm Restore Code E5
193 - 194 Primary # Zone 1 Disable Restore Code E1
195 - 196 Primary # Zone 2 Disable Restore Code E2
197 - 198 Primary # Zone 3 Disable Restore Code E3
199 - 200 Primary # Zone 4 Disable Restore Code E4
201 - 202 Primary # Zone 5 Disable Restore Code E5
203 - 204 Primary # Drill Restore Code 98
205 - 206 Primary # AC Fault Restore Code E6
207 - 208 Primary # Zone 1 Fault Restore Code E1
209 - 210 Primary # Zone 2 Fault Restore Code E2
211 - 212 Primary # Zone 3 Fault Restore Code E3
213 - 214 Primary # Zone 4 Fault Restore Code E4
215 - 216 Primary # Zone 5 Fault Restore Code E5
217 - 218 Primary # Earth Fault Restore Code E7
219 - 220 Primary # Low Battery Fault Restore Code E8
221 - 222 Primary # No Battery Fault Restore Code E9
223 - 224 Primary # Telco Primary Line Fault Restore Code EA
225 - 226 Primary # Telco Secondary Line Fault Restore Code EB
227 - 228 Primary # NAC # 1 Fault Restore Code EC
229 - 230 Primary # NAC # 2 Fault Restore Code EC
231 - 232 Primary # Communication Trouble Primary # Restore Code ED
233 - 234 Primary # Communication Trouble Secondary # Restore Code EE
235 - 236 Primary # Annunciator Fault Restore Code EC
237 - 238 Primary # System Off Normal Restore Code EF
239 - 240 Primary # System Test Report 99
241 - 242 Primary # System Abnormal Test Report 91
243 - 244 Primary # Request for Upload/Download 71
245 - 246 Primary # Successful Upload 72
247 - 248 Primary # Successful Download 73
249 - 250 Primary # Failed Upload/Download 74

Document #15140 Rev.G 01/02/02 P/N 15140:G

37

Programming Options

Ademco Contact ID Format

If 'E' is entered for address 16 in Program Mode Level 1, the data shown in Table 3-3 is automatically pro­grammed for the Primary Central Station phone number event codes. Enter '000' for the setting to disable the
report. The Setting entry is programmable, the Zone Number cannot be changed. Restoral code settings match
the settings shown with the addition of an 'R' code transmitted. Refer to page 83 for additional information.

TABLE 3-3:

Address Description Setting Zone No.

Event Codes, Primary Central Station Number

127-129 Primary # Zone 1 Alarm Code 111 001
130-132 Primary # Zone 2 Alarm Code 111 002
133-135 Primary # Zone 3 Alarm Code 111 003
136-138 Primary # Zone 4 Alarm Code 111 004
139-141 Primary # Zone 5 Alarm Code 111 005
142-144 Primary # Zone 1 Disabled Code 570 001
145-147 Primary # Zone 2 Disabled Code 570 002
148-150 Primary # Zone 3 Disabled Code 570 003
151-153 Primary # Zone 4 Disabled Code 570 004
154-156 Primary # Zone 5 Disabled Code 570 005
157-159 Primary # Drill Code 604 000
160-162 Primary # AC Fault Code 301 000
163-165 Primary # Zone 1 Fault Code 380 001
166-168 Primary # Zone 2 Fault Code 380 002
169-171 Primary # Zone 3 Fault Code 380 003
172-174 Primary # Zone 4 Fault Code 380 004
175-177 Primary # Zone 5 Fault Code 380 005
178-180 Primary # Earth Fault Code 310 000
181-183 Primary # Low Battery Fault Code 302 000
184-186 Primary # No Battery Fault Code 311 000
187-189 Primary # Telco Primary Line Fault Code 351 000
190-192 Primary # Telco Secondary Line Fault Code 352 000
193-195 Primary # NAC #1 Fault Code 321 001
196-198 Primary # NAC #2 Fault Code 322 002
199-201 Primary # Comm Trouble Primary # Code 354 001
202-204 Primary # Comm Trouble Secondary # Code 354 002
205-207 Primary # Annunciator Fault Code 330 000
208-210 Primary # System Off Normal Code 308 000
211-213 Primary # System Test Message 602 000
214-216 Primary # System Abnormal Test Message 608 000
217-219 Primary # Upload/Download Request Code 411 000
220-222 Primary # Upload Successful Code 416 000
223-225 Primary # Download Successful Code 412 000
226-228 Primary # Upload/Download Failed Code 413 000

38

Document #15140 Rev.G 01/02/02 P/N 15140:G

Programming Options

Primary Central Station Number Account Code (17-20)

A unique account code is provided by the Central Station. Four locations at addresses 17-20 (factory default settings
of all '0s') are used to enter the account code. Valid entries are 0 to 9 and A to F. The number of digits entered must
match the format selection. If programming '2, 3, 4 or 5' into address 16, enter the three digit account code supplied
by the Central Station (location 20 is ignored). If programming '0, 1, 6, 7, 8, 9, A, B, C or D' into address 16, enter
the four digit account code supplied by the Central Station.

Primary Central Station Number 24 Hour Test Time (21-24)

Use military time when entering the 24 hour 'test' time. The 24 hour test report to phone number 1 takes up four loca­tions, from addresses 21-24. The default is '2345' (11:45 PM). The limits for each address location are as follows:

21 - enter 0-2

22 - enter 0-9

23 - enter 0-5

24 - enter 0-9

Do not use 'A-F'

Primary Central Station Number 24/12/8/6 Hour Test Time Interval (25)

The test report sent to the Primary phone number may be sent every 6, 8, 12 or 24 hours. If the message is to be sent
every 24 hours, leave the factory default entry of '0'. If other test report times are needed, enter '1' for 12 hours, '2' for
8 hours or '3' for 6 hours.

Secondary Central Station Phone Number (26-41)

Addresses (26-41) are factory set to 'F' (26_F to 41_F). Programming this feature is typically done as follows: If the
phone number to be entered is 484-7161, press 4. The display will read 26_4. Press [ENTER/STORE] to save the
entry to memory and increment to the next address 27_F.

Enter the remaining numbers in their respective addresses as shown below:

Phone Number

Addresses

4847161FFFFFFFFF

26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41

Valid entries for both the primary and secondary phone numbers are 0 - F with the numeric digits as dialed numbers
and the alpha-characters representing the following functions:

A = * on a Touchtone phone keypad

B = # on a Touchtone phone keypad

C = look for secondary dial tone for up to two seconds (then dial anyway)

D = 3-second pause

E = 5-second pause

F = end of phone number (Note: F must be entered)

Document #15140 Rev.G 01/02/02 P/N 15140:G

39

Programming Options

Secondary Central Station Number Communication Format (42)

One location is needed to select the Communication Format for the secondary phone number. Address 42 is used for
this purpose. The default (factory setting) for this address is 'E' for Ademco Contact ID format. Selections '0'
through 'E' may be entered in place of the default entry. After making the selection, press the [ENTER/STORE] key
to store the selection. The available format options are as follows:

0: 4+1 Ademco Express Standard, DTMF, 1400/2300 ACK

1: 4+2 Ademco Express Standard, DTMF, 1400/2300 ACK

2: 3+1 Standard 1800 Hz Carrier, 2300 Hz ACK

3: 3+1 Expanded 1800 Hz Carrier, 2300 Hz ACK

4: 3+1 Standard 1900 Hz Carrier, 1400 Hz ACK

5: 3+1 Expanded 1900 Hz Carrier, 1400 Hz ACK

6: 4+1 Standard 1800 Hz Carrier, 2300 Hz ACK

7: 4+1 Expanded 1800 Hz Carrier, 2300 Hz ACK

8: 4+1 Standard 1900 Hz Carrier, 1400 Hz ACK

9: 4+1 Expanded 1900 Hz Carrier, 1400 Hz ACK

A: 4+2 Standard 1800 Hz Carrier, 2300 Hz ACK

B: 4+2 Expanded 1800 Hz Carrier, 2300 Hz ACK

C: 4+2 Standard 1900 Hz Carrier, 1400 Hz ACK

D: 4+2 Expanded 1900 Hz Carrier, 1400 Hz ACK

E: Ademco Contact ID, DTMF, 1400/2300 ACK

F: Not Used

Note: Consult your Central Station for proper selection or consult our factory representatives. For any format cho­sen, the control panel automatically programs all of the event codes. Refer to Table 3-1 through Table 3-5 .

40

Document #15140 Rev.G 01/02/02 P/N 15140:G

Programming Options

3+1, 4+1 Express, 4+1 Standard and Expanded & 4+2 Expanded Formats

If '0, 2, 3, 4, 5, 6, 7, 8, 9, B or D' is entered for address 42, the following data is automatically programmed for the
Secondary Central Station phone number event codes. Enter '0' for the Setting to disable the report.

TAB LE 3- 4:

Secondary Event Codes-3+1, 4+1 Express, 4+1 Standard, Expanded & 4+2 Expanded

Address Description Setting

251 Secondary # Zone 1 Alarm Code 1
252 Secondary # Zone 2 Alarm Code 1
253 Secondary # Zone 3 Alarm Code 1
254 Secondary # Zone 4 Alarm Code 1
255 Secondary # Zone 5 Alarm Code 1
256 Secondary # Zone 1 Disable Code F
257 Secondary # Zone 2 Disable Code F
258 Secondary # Zone 3 Disable Code F
259 Secondary # Zone 4 Disable Code F
260 Secondary # Zone 5 Disable Code F
261 Secondary # Drill Code 9
262 Secondary # AC Fault Code F
263 Secondary # Zone 1 Fault Code F
264 Secondary # Zone 2 Fault Code F
265 Secondary # Zone 3 Fault Code F
266 Secondary # Zone 4 Fault Code F
267 Secondary # Zone 5 Fault Code F
268 Secondary # Earth Fault Code F
269 Secondary # Low Battery Fault Code F
270 Secondary # No Battery Fault Code F
271 Secondary # Telco Primary Line Fault Code F
272 Secondary # Telco Secondary Line Fault Code F
273 Secondary # NAC #1 Fault Code F
274 Secondary # NAC #2 Fault Code F
275 Secondary # Communication Trouble Primary # Code F
276 Secondary # Communication Trouble Secondary # Code F
277 Secondary # Annunciator Fault Code F
278 Secondary # System Off Normal Code F
279 Secondary # Zone 1 Alarm Restore Code E
280 Secondary # Zone 2 Alarm Restore Code E
281 Secondary # Zone 3 Alarm Restore Code E
282 Secondary # Zone 4 Alarm Restore Code E
283 Secondary # Zone 5 Alarm Restore Code E
284 Secondary # Zone 1 Disable Restore Code E
285 Secondary # Zone 2 Disable Restore Code E
286 Secondary # Zone 3 Disable Restore Code E
287 Secondary # Zone 4 Disable Restore Code E
288 Secondary # Zone 5 Disable Restore Code E
289 Secondary # Drill Restore Code 9
290 Secondary # AC Fault Restore Code E
291 Secondary # Zone 1 Fault Restore Code E
292 Secondary # Zone 2 Fault Restore Code E
293 Secondary # Zone 3 Fault Restore Code E
294 Secondary # Zone 4 Fault Restore Code E
295 Secondary # Zone 5 Fault Restore Code E
296 Secondary # Earth Fault Restore Code E
297 Secondary # Low Battery Fault Restore Code E
298 Secondary # No Battery Fault Restore Code E
299 Secondary # Telco Primary Line Fault Restore Code E
300 Secondary # Telco Secondary Line Fault Restore Code E
301 Secondary # NAC # 1 Fault Restore Code E
302 Secondary # NAC # 2 Fault Restore Code E
303 Secondary # Communication Trouble Primary # Restore Code E
304 Secondary # Communication Trouble Secondary # Restore Code E
305 Secondary # Annunciator Fault Restore Code E
306 Secondary # System Off Normal Restore Code E
307 Secondary # System Test Report 9
308 Secondary # System Abnormal Test Report F
309 Secondary # Request for Upload/Download 7
310 Secondary # Successful Upload 7
311 Secondary # Successful Download 7
312 Secondary # Failed Upload/Download 7

Document #15140 Rev.G 01/02/02 P/N 15140:G

41

Programming Options

4+2 Standard and 4+2 Express Formats

If '1, A or C' is entered for address 42, the following data is automatically programmed for the Secondary Central Sta­tion phone number event codes. Enter '00' for the Setting to disable the report.

TABLE 3-5:

Secondary Event Codes - 4+2 Standard and 4+2 Express

Address Description Setting

251 - 252 Secondary # Zone 1 Alarm Code 11
253 - 254 Secondary # Zone 2 Alarm Code 12
255 - 256 Secondary # Zone 3 Alarm Code 13
257 - 258 Secondary # Zone 4 Alarm Code 14
259 - 260 Secondary # Zone 5 Alarm Code 15
261 - 262 Secondary # Zone 1 Disable Code F1
263 - 264 Secondary # Zone 2 Disable Code F2
265 - 266 Secondary # Zone 3 Disable Code F3
267 - 268 Secondary # Zone 4 Disable Code F4
269 - 270 Secondary # Zone 5 Disable Code F5
271 - 272 Secondary # Drill Code 97
273 - 274 Secondary # AC Fault Code F6
275 - 276 Secondary # Zone 1 Fault Code F1
277 - 278 Secondary # Zone 2 Fault Code F2
279 - 280 Secondary # Zone 3 Fault Code F3
281 - 282 Secondary # Zone 4 Fault Code F4
283 - 284 Secondary # Zone 5 Fault Code F5
285 - 286 Secondary # Earth Fault Code F7
287 - 288 Secondary # Low Battery Fault Code F8
289 - 290 Secondary # No Battery Fault Code F9
291 - 292 Secondary # Telco Primary Line Fault Code FA
293 - 294 Secondary # Telco Secondary Line Fault Code FB
295 - 296 Secondary # NAC #1 Fault Code FC
297 - 298 Secondary # NAC #2 Fault Code FC
299 - 300 Secondary # Communication Trouble Primary # Code FD
301 - 302 Secondary # Communication Trouble Secondary # Code FE
303 - 304 Secondary # Annunciator Fault Code FC
305 - 306 Secondary # System Off Normal Code FF
307 - 308 Secondary # Zone 1 Alarm Restore Code E1
309 - 310 Secondary # Zone 2 Alarm Restore Code E2
311 - 312 Secondary # Zone 3 Alarm Restore Code E3
313 - 314 Secondary # Zone 4 Alarm Restore Code E4
315 - 316 Secondary # Zone 5 Alarm Restore Code E5
317 - 318 Secondary # Zone 1 Disable Restore Code E1
319 - 320 Secondary # Zone 2 Disable Restore Code E2
321 - 322 Secondary # Zone 3 Disable Restore Code E3
323 - 324 Secondary # Zone 4 Disable Restore Code E4
325 - 326 Secondary # Zone 5 Disable Restore Code E5
327 - 328 Secondary # Drill Restore Code 98
329 - 330 Secondary # AC Fault Restore Code E6
331 - 332 Secondary # Zone 1 Fault Restore Code E1
333 - 334 Secondary # Zone 2 Fault Restore Code E2
335 - 336 Secondary # Zone 3 Fault Restore Code E3
337 - 338 Secondary # Zone 4 Fault Restore Code E4
339 - 340 Secondary # Zone 5 Fault Restore Code E5
341 - 342 Secondary # Earth Fault Restore Code E7
343 - 344 Secondary # Low Battery Fault Restore Code E8
345 - 346 Secondary # No Battery Fault Restore Code E9
347 - 348 Secondary # Telco Primary Line Fault Restore Code EA
349 - 350 Secondary # Telco Secondary Line Fault Restore Code EB
351 - 352 Secondary # NAC # 1 Fault Restore Code EC
353 - 354 Secondary # NAC # 2 Fault Restore Code EC
355 - 356 Secondary # Communication Trouble Primary # Restore Code ED
357 - 358 Secondary # Communication Trouble Secondary # Restore Code EE
359 - 360 Secondary # Annunciator Fault Restore Code EC
361 - 362 Secondary # System Off Normal Restore Code EF
363 - 364 Secondary # System Test Report 99
365 - 366 Secondary # System Abnormal Test Report 91
367 - 368 Secondary # Request for Upload/Download 71
369 - 370 Secondary # Successful Upload 72
371 - 372 Secondary # Successful Download 73
373 - 374 Secondary # Failed Upload/Download 74

42

Document #15140 Rev.G 01/02/02 P/N 15140:G

Programming Options

Ademco Contact ID Format

If 'E' is entered for address 42 in Program Mode Level 1, the data shown in Table 3-6 is automatically pro­grammed for the Secondary Central Station phone number event codes. Enter '000' for the setting to disable the
report. The Setting entry is programmable, the Zone Number cannot be changed. Restoral code settings match
the settings shown with the addition of an 'R' code transmitted. Refer to page 83 for additional information.

TAB LE 3- 6:

Address Description Setting Zone No.

Event Codes, Secondary Central Station Number

251-253 Secondary # Zone 1 Alarm Code 111 001
254-256 Secondary # Zone 2 Alarm Code 111 002
257-259 Secondary # Zone 3 Alarm Code 111 003
260-262 Secondary # Zone 4 Alarm Code 111 004
263-265 Secondary # Zone 5 Alarm Code 111 005
266-268 Secondary # Zone 1 Disabled Code 570 001
269-271 Secondary # Zone 2 Disabled Code 570 002
272-274 Secondary # Zone 3 Disabled Code 570 003
275-277 Secondary # Zone 4 Disabled Code 570 004
278-280 Secondary # Zone 5 Disabled Code 570 005
281-283 Secondary # Drill Code 604 000
284-286 Secondary # AC Fault Code 301 000
287-289 Secondary # Zone 1 Fault Code 380 001
290-292 Secondary # Zone 2 Fault Code 380 002
293-295 Secondary # Zone 3 Fault Code 380 003
296-298 Secondary # Zone 4 Fault Code 380 004
299-301 Secondary # Zone 5 Fault Code 380 005
302-304 Secondary # Earth Fault Code 310 000
305-307 Secondary # Low Battery Fault Code 302 000
308-310 Secondary # No Battery Fault Code 311 000
311-313 Secondary # Telco Primary Line Fault Code 351 000
314-316 Secondary # Telco Secondary Line Fault Code 352 000
317-319 Secondary # NAC #1 Fault Code 321 001
320-322 Secondary # NAC #2 Fault Code 322 002
323-325 Secondary # Comm Trouble Primary # Code 354 001
326-328 Secondary # Comm Trouble Secondary # Code 354 002
329-331 Secondary # Annunciator Fault Code 330 001
332-334 Secondary # System Off Normal Code 308 000
335-337 Secondary # System Test Message 602 000
338-340 Secondary # System Abnormal Test Message 608 000
341-343 Secondary # Upload/Download Request Code 411 000
344-346 Secondary # Upload Successful Code 416 000
347-349 Secondary # Download Successful Code 412 000
350-352 Secondary # Upload/Download Failed Code 413 000

Document #15140 Rev.G 01/02/02 P/N 15140:G

43

Programming Options

Secondary Central Station Number Account Code (43-46)

A unique account code is provided by the Central Station. Four locations at addresses 43-46 (factory default settings
of all '0s') are used to enter the account code. Valid entries are 0 to 9 and A to F. The number of digits entered must
match the format selection. If programming '2, 3, 4 or 5' into address 42, enter the three digit account code supplied
by the Central Station (location 46 is ignored). If programming '0, 1, 6, 7, 8, 9, A, B, C or D' into address 42, enter
the four digit account code supplied by the Central Station.

Secondary Central Station Number 24 Hour Test Time (47-50)

Use military time when entering the 24 hour 'test' time. The 24 hour test report to phone number 2 takes up four loca­tions, from addresses 47-50. The default is '0000' (12:00 midnight). The limits for each location are as follows:

47 - enter 0-2

48 - enter 0-9

49 - enter 0-5

50 - enter 0-9

Do not use 'A-F'

Secondary Central Station Number 24/12/8/6 Hour Test Time Interval (51)

The test report sent to the Secondary phone number may be sent every 6, 8, 12 or 24 hours. If the message is to be
sent every 24 hours, leave the factory default entry of '0'. If other test report times are needed, enter '1' for 12 hours,
'2' for 8 hours or '3' for 6 hours.

Alarm Verification (52)

Alarm verification works only on zones programmed as 2-wire smoke detector zones. After detecting an alarm, the
panel removes power from all zones for six seconds, resetting all 2-wire smoke detectors. Power is reapplied and a
12 second retard period allows detectors to stabilize. During the retard/reset period of 18 seconds, subsequent alarms
by the same initiating zone are ignored. An alarm detected on any other 2-wire detector zone during the retard period
will cause immediate verified alarms. A subsequent alarm on the initiating zone occurring within the confirmation
time will cause a verified alarm. Note: Mixing devices on zones designated as 2-wire smoke zones is not

recommended.

During the alarm verification period, access to other modes of operation is prevented.

FIGURE 3-2:

Detector Alarm Verification

Detector Zone Goes Into Alarm

Different Detector Zone Alarms

Verification Timing Diagram

0 Sec.

6 Sec.

RESET RETARD

Alarm Ignored

18 Sec.

0

ALARM VERIFICATION PERIOD

Control Panel Processes Alarm if Same Detector Zone if Still in Alarm

CONFIRMATION TIME

30

Control Panel Immediately Processes Alarm

9060

120 Sec.

120

Factory default selection is no verification which is a '0' entry. Entering a '1' enables alarm verification. Note: Con­sult local Authority Having Jurisdiction (AHJ) prior to altering this address.

Future Use (53-55)

Slave Communicator/Fire Panel Selection (56)

Leaving address 56 at '0' causes the control panel to operate as a fire panel only. Selecting '1' will make it operate as
a slave communicator only. Selecting '2' will make it operate as a fire panel/communicator.

44

Document #15140 Rev.G 01/02/02 P/N 15140:G

Programming Options

Zones 1-5 Function Selection (57-61)

The five zones on the control panel may be programmed as shown below. Program entries alter zone function and
transmittal priority.

When using Ademco Contact ID format, Zone Alarm and Zone Restoral event codes change automatically as shown
in Table 3-7 . Be certain to reprogram alarm event codes when selecting process monitoring functions. Zone fault
and disable event codes may also be user reprogrammed (refer to “Ademco Contact ID Format Event Code Descrip­tions” on page 83).

TABLE 3-7:

Program Entry Function

1. Ademco Contact ID format selection causes Event Codes to automatically change to values shown in Table 3-7 .

Zone Function Selection

Zone Alarm/Restoral1

Event Code

0 Operates 2-wire smoke detectors 111
1 Pull station 115
2 Normally open contact device 110
3 Supervisory 200
4 Supervisory autoresettable - self restore function, is not latched by the

control panel 200

5 Waterflow silenceable - silencing of silenceable NACs allowed (affects

zone 3 only) 113

6 Waterflow nonsilenceable - silencing of silenceable NACs is not allowed.

Must clear waterflow alarm condition and press the reset key (affects zone
3 only) 113

Zone 1 Function Selection (57)

Factory default for zone 1 is '0' for 2-wire smoke detector. Enter '1' for pull station; '2' for normally open contact
device; '3' for supervisory; '4' for supervisory autoresettable.

Zone 2 Function Selection (58)

Factory default for zone 2 is '0' for 2-wire smoke detector. Enter '1' for pull station; '2' for normally open contact
device; '3' for supervisory; '4' for supervisory autoresettable.

Zone 3 Function Selection (59)

Factory default for zone 3 is '0' for 2-wire smoke detector. Enter '1' for pull station; '2' for normally open contact
device; '3' for supervisory; '4' for supervisory autoresettable; '5' for waterflow silenceable; '6' for waterflow
nonsilenceable.

Zone 4 Function Selection (60)

Factory default for zone 4 is '0' for 2-wire smoke detector. Enter '1' for pull station; '2' for normally open contact
device; '3' for supervisory; '4' for supervisory autoresettable.

Zone 5 Function Selection (61)

Factory default for zone 5 is '0' for 2-wire smoke detector. Enter '1' for pull station; '2' for normally open contact
device; '3' for supervisory; '4' for supervisory autoresettable.

Note: Programming any zone to function as supervisory or supervisory autoresettable will cause the defaulted event
codes (see notes in Table 3-1 through Table 3-5 ) to be automatically changed. The defaulted code of '1' is changed
to '8' for formats 3+1 and 4+1 Standard and Expanded, 4+2 Expanded and 4+1 Express. The defaulted codes of 11,
12, 13, 14 and 15 are changed to 81, 82, 83, 84 and 85 accordingly for formats 4+2 Standard and 4+2 Express.

Waterflow Retard Timer (62-63)

A delay may be added prior to declaring a waterflow type of alarm. Delays up to 89 seconds are allowed. The
default for addresses 62 and 63 are '00' (no additional delay). Valid entries for address 62 are 0-8 and for address 63
are 0-9. Program entries into these addresses only if entering a '5' or '6' in address 59. Be careful to include any built-

in delays of the waterflow device.

Document #15140 Rev.G 01/02/02 P/N 15140:G

45

Programming Options

AC Loss Reporting Delay (64)

Enter a digit of '1'-'F', corresponding to the number of hours to be delayed in reporting loss of AC power. The factory
default setting is '0' for 6 hour delay. If 24 hour battery backup is being employed, select from choices '0' through '6'.
If 60 hour backup is used, select from choices '7' through 'F'. Selections are: '0' for 6 hour delay; '1' for 7 hours; '2' for
8 hours; '3' for 9 hours; '4' for 10 hours; '5' for 11 hours; '6' for 12 hours; '7' for 15 hours; '8' for 16 hours; '9' for 17
hours; 'A' for 18 hours; 'B' for 19 hours; 'C' for 20 hours; 'D' for 21 hours; 'E' for 22 hours; 'F' for 23 hours.

Alarm Presignal (65)

Alarm Presignal is used to delay NAC (Notification Appliance Circuit) activation while allowing for visual verifica­tion by a person. Once a zone triggers an alarm, the main board piezo and the annunciator piezo sounders turn on
steady, the display indicates the activated zone, the alarm LED blinks and the NACs are held off for 15 seconds. Dur­ing this time, if the silence switch is pressed, the notification appliances may be held off for up to three minutes (see
Presignal Delay Timer Address 66-68). After the programmed delay period, the notification appliances will activate.
Presignal does not function for zones defined as waterflow or supervisory. Factory default is '0' for no alarm presig­nal. Enter '1' to select alarm presignal. During alarm presignal, access to other modes is prevented.

Alarm Presignal Delay Timer (66-68)

The alarm presignal delay timer is factory set to 120 seconds (2 minutes), address 66=1, 67=2 and 68=0. The timer
may be programmed from 0 to 179 seconds. Location 65 must be set to '1' for the delay timer to operate.

Notification Appliance Circuit #1 Enable (69)

NAC #1 may be programmed as '0' for silenceable, '1' for nonsilenceable or '2' for disabled (disabling will cause the
display to indicate 'bEL1', system trouble light to turn on and onboard piezo to sound). Factory default is '0' for
silenceable. Note: Consult the local Authority Having Jurisdiction (AHJ) prior to altering this address.

Silence Inhibit Notification Appliance Circuit #1 (70)

Setting address 70 to '1' prohibits silencing of NAC #1 and the onboard piezo for one minute. Factory default is '0' for
no silence inhibit of NAC #1.

Autosilence Notification Appliance Circuit #1 (71)

NAC #1 may be autosilenced after a programmed time interval between 5 and 30 minutes. Enter '1' for 5 minute
autosilence, '2' for 10 minutes, '3' for 15 minutes, '4' for 20 minutes, '5' for 25 minutes or '6' for 30 minutes. The fac­tory default is '0' for no autosilence.

Coding Notification Appliance Circuit #1 (72)

Coding of NAC #1 is programmable by selecting '1' for March Time (120 ppm), '2' for California (10 seconds On, 5
seconds Off) or '3' for Temporal (½ second On, ½ second Off, ½ second On, ½ second Off, ½ second On, 1½ seconds
Off). Factory default is '0' for no coding (steady).

Notification Appliance Circuit #2 Enable (73)

NAC #2 may be programmed as '0' for silenceable, '1' for nonsilenceable or '2' for disabled (disabling will cause the
display to indicate 'bEL2', system trouble light to turn on and onboard piezo to sound). Factory default is '0' for
silenceable. Note: Consult the local Authority Having Jurisdiction (AHJ) prior to altering this address.

Silence Inhibit Notification Appliance Circuit #2 (74)

Setting address 74 to '1' prohibits silencing of NAC #2 and the onboard piezo for one minute. Factory default is '0' for
no silence inhibit of NAC #2.

Autosilence Notification Appliance Circuit #2 (75)

NAC #2 may be autosilenced after a programmed time interval between 5 and 30 minutes. Enter '1' for 5 minute
autosilence, '2' for 10 minutes, '3' for 15 minutes, '4' for 20 minutes, '5' for 25 minutes or '6' for 30 minutes. The fac­tory default is '0' for no autosilence.

46

Document #15140 Rev.G 01/02/02 P/N 15140:G

Programming Options

Coding Notification Appliance Circuit #2 (76)

Coding of NAC #2 is programmable by selecting '1' for March Time (120 ppm), '2' for California (10 seconds On, 5
seconds Off) or '3' for Temporal (½ second On, ½ second Off, ½ second On, ½ second Off, ½ second On, 1½ seconds
Off). Factory default is '0' for no coding (steady).

Trouble Reminder (77)

Factory default is '0' which disables the trouble reminder feature. Selecting '1' will cause a reminding beep (after the
silence switch is pressed), every 15 seconds during an alarm and every two minutes during a trouble condition. The
beeps from the onboard piezo sounder will continue until the alarm or fault is cleared.

Annunciator/Printer Supervision (78)

Factory default is '0' for no annunciator or printer present. Set address 78 to '1' if an annunciator is present, set to '2'
if a printer is present or set to '3' if both an annunciator and a printer are present.

Backup Reporting (79)

Leaving the default setting of '0' programs the control panel to transmit reports to the Secondary Central Station
phone number only if attempts to communicate to the Primary Central Station phone number are unsuccessful. Pro­gramming a '1' causes all reports to be transmitted to the Secondary Central Station Phone number.

Touchtone/Rotary Select (80)

A '0' programmed in this address by the factory triggers Touchtone dialing over both phone lines. Select '1' for rotary
dialing.

Make/Break Ratio (81)

Use this address only if '1' (rotary dialing) has been selected for address 80. The make/break ratio is factory set to '0'
for 67/33 ratio, but may be changed to '1' for 62/38 ratio.

Address (82)

Leave default of '0'.

Address (83)

Leave default of '0'.

Panel Identification Number (84-87)

The Panel Identification Number is a 4-digit code (valid digits are 0-F) that is used to identify the installed panel.
This code is separate from the 8-digit secret code loaded in by the Service Terminal. It is important to program this 4­digit code at the jobsite the first time that downloading is performed so that the called Service Terminal can identify
the control panel.

Service Terminal Number 1 Phone Number (88-103)

Addresses 88 through 103 are reserved for the Service Terminal phone number 1. Factory default is all 'Fs'. Valid
entries are 0-9 plus A, B, C, D and E, similar to the primary and secondary Central Station phone number entries pro­grammed at addresses 00-15 and 26-41. Use 'F' to designate the end of the phone number.

Ring Count on Primary Phone Line (104-105)

Use this address to designate the number of rings allowed on the primary phone line prior to answering an incoming
call from a Service Terminal. Factory default is '03' which means the panel will not answer an incoming call until 3
rings are detected. This entry may be programmed up to a maximum of 25 rings. A setting of '00' prevents the panel
from answering incoming calls.

Document #15140 Rev.G 01/02/02 P/N 15140:G

47

Programming Options

FAX/Answer Machine, Primary Phone Line (106)

This entry is used when the primary phone line is being shared with a FAX, answering machine or other device. Fac­tory default is '0' for no sharing of the primary phone line. An entry of '1' indicates sharing and allows the panel to
wait for three consecutive calls from the Service Terminal, spaced 30 seconds apart, before responding.

Service Terminal Number 2 Phone Number (107-122)

Addresses 107 through 122 are reserved for the Service Terminal phone number 2. Factory default is all 'Fs'. Valid
entries are 0-9 plus A, B, C, D and E, similar to the primary and secondary Central Station phone number entries pro­grammed at addresses 00-15 and 26-41. Use 'F' to designate the end of the phone number.

Ring Count on Secondary Phone Line (123-124)

Use this address to designate the number of rings allowed on the secondary phone line prior to answering an incom­ing call from a Service Terminal. Factory default is '03' which means the panel will not answer an incoming call until
3 rings are detected. This entry may be programmed up to a maximum of 25 rings. A setting of '00' prevents the
panel from answering incoming calls.

FAX/Answer Machine, Secondary Phone Line (125)

This entry is used when the secondary phone line is being shared with a FAX, answering machine or other device.
Factory default is '0' for no sharing of the secondary phone line. An entry of '1' indicates sharing and allows the panel
to wait for three consecutive calls from the Service Terminal, spaced 30 seconds apart, before responding.

Upload/Download Reports Sent to Secondary Central Station Phone Number, Backup or Always (126)

Reports for request for 'upload/download', 'successful upload', 'successful download' and 'failed upload/download' are
always sent to the primary Central Station phone number. This entry allows for the same reports to either always be
sent to the secondary Central Station phone number or only if attempts to transmit to the primary Central Station
phone number are unsuccessful. Factory default is '0' for backup only. Enter '1' for always.

Programming Event Codes (127-374)

The type of reports and event codes that are sent to the Central Station are in Table 3-1 through Table 3-5 . The
selections made for the Primary Central Station Number Communication Format (address 16) and the Secondary
Central Station Number Communication Format (address 42) automatically program addresses 127-374 with factory
default selections.

Any of the event codes may be changed. Consult your Central Station prior to altering the event codes. Entering an
event code of '0' will cause the communicator to NOT transmit the report. For the 3+1, 4+1 and 4+1 Express formats
or the 4+2 Expanded format, enter '0'. For the 4+2 Standard or 4+2 Express formats, enter '00'. Transmission of
reports to either or both Central Station phone numbers may be disabled.

Note the special 'System Abnormal Test Report' event code. This report was added per new UL DACT requirements.
This report is generated in place of the normal test report when an alarm and/or trouble condition exists at the time
the test report is due to be sent.

Programming the Real-Time Clock and Calendar

Entering an address greater than 374 will cause a display of the current time. On initial power-up, the clock will start
running from the factory setting of 00:01 (military time). The far left digit will be flashing, indicating that this is the
first digit to be programmed. It should be noted that setting the time and date may cause corruption of the History

File. For this reason, it is important that the History File be cleared after the time and date has been set. Refer to
“History Mode” on page 63.

Hours/Minutes

Select a digit then press [ENTER/STORE]. The digit 2nd from the left will start flashing. Select a digit then press
[ENTER/STORE]. Hours setting is complete. With the digit 2nd from the right flashing, select a digit then press
[ENTER/STORE]. The digit on the far right will start flashing. Select a digit then press [ENTER/STORE]. Min-

utes setting is complete.

48

Document #15140 Rev.G 01/02/02 P/N 15140:G

Default Programming

Ye a r

After entering the last digit corresponding to minutes (far right digit), the display will read 1994 with the digit 9 (sec­ond from the right) flashing. Press [ENTER/STORE] if the 9 is acceptable. The digit farthest right will begin flash­ing. Enter the appropriate digit corresponding to the last digit of the current year and press the [ENTER/STORE]
key to complete programming of the year.

Note that changing to the year 2000

can be accomplished by entering ‘0’ while the second digit from the right is

flashing, followed by the [ENTER/STORE] key. The two digits to the left will change to ‘20’ and the digit farthest
right will begin flashing. Enter the appropriate digit corresponding to the last digit of the year (i.e. ‘0’ for the year

2000

) and press the [ENTER/STORE] key to complete programming of the year.

Month/Day

After the year is entered, the display will show four digits representing the month and day of the software release
date. The month is represented by the two digits on the left and the day by the two digits on the right. The digit on
the far left will be flashing. The month and day are set the same way as the hours and minutes. Once the last digit
corresponding to the day is entered, the display will show the contents of address '00'. The real-time clock/calendar
keeps track of leap years automatically.

Note that the software for the MS-5024UD operates the internal clock based upon 60Hz. The software for the
MS-5024UDE operates the internal clock based upon 50Hz.

End Programming

Exit Programming Mode by pressing MODE, followed by the 4-digit code corresponding to an alternate mode of
operation, then press [ENTER/STORE].

During Program Mode, if no key is pressed within 10 minutes, the panel will return to Normal Mode.

3.4 Default Programming

To return all program entries to their factory original settings, perform the following steps only when the system is
idle in Normal standby condition:

Press the MODE key followed by the four digit code 3337 and press the [ENTER/STORE] key.

3337 spells DEFP (DEFault Programming) on a Touch-Tone

☛

®

phone

If an incorrect key is pressed, reenter the proper 4-digit code before pressing the [ENTER/STORE] key.

Within five seconds, repeat this entry by again pressing the MODE key followed by the 4-digit code 3337 and press­ing the [ENTER/STORE] key. The display will read 3337 while the E

2

nonvolatile memory (storage area for all
programming options) is being reprogrammed with the original default settings. When reprogramming is complete,
the display will be blank.

Document #15140 Rev.G 01/02/02 P/N 15140:G

49

Operating Instructions

CHAPTER 4 Operating Instructions

The MS-5024UD has six modes of operation:

• Normal Mode

•Program Mode

• Walktest Mode

• Troubleshoot Mode

• History Mode

• Print Mode

Upon initial power-up, the system will be in Normal Mode. This chapter discusses operation of the control panel in
the Normal Mode.

4.1 Switches in Normal Mode

4.1.1 RESET

The Reset Switch resets the system and any smoke detectors. If the Reset Switch is pressed, the control panel will:

✓

Clear the display and status LEDs

✓ Turn off the Notification Appliance Circuits
✓ Reset all zones by temporarily removing power
✓

Silence the onboard piezo sounder

✓

Store 'reset' message in the History file

✓

Restore the alarm and trouble relays to normal

✓

Clear the supervisory and communication fail relay driver outputs

✓

Temporarily remove power from the resettable power output TB4 terminals 3 & 4

✓

Restore to normal the RM-5F zone relays

✓

Output 'reset' message to printer

Any alarm, supervisory or trouble condition that exists after a system reset, will resound the system, reactivating nor­mal system activity. Upon release of the Reset Switch, the display will read rES_ for six seconds.

50

Document #15140 Rev.G 01/02/02 P/N 15140:G

Displays

SILENCE

If the Silence Switch is pressed:

✓ The silenceable NACs will be turned Off

✓ The silence LED will be turned Off

✓ The piezo sounder will be shut Off

✓ 'System Silenced' message will be stored in the History file

✓

'System Silenced' message will be sent to the printer

✓ System Silence switch acts as acknowledge switch during alarm presignal

Upon the occurrence of a subsequent event (alarm or trouble), System Silence is overridden and the control panel will
respond to the new event. The System Silence switch will be ignored for silenceable waterflow type alarms.

MODE

Pressing the MODE switch followed by a valid 4-digit numerical code and then the [ENTER/STORE] key selects
one of the six modes of operation. To enter Normal Mode from any other mode, press MODE, then 6676 followed
by the [ENTER/STORE] key.

6676 spells NORM on a Touchtone

☛

®

phone.

1st EVENT

The 1st Event switch, along with the Up and Down arrow keys, is used to display any currently active alarm and/or
fault conditions present in the system. Press the 1st Event switch at any time to display the first event (alarm and/or
trouble) that occurred.

DOWN ARROW

The Down Arrow key is used to view other events (newer) that have occurred and are active (not yet cleared).

UP ARROW

The Up Arrow key is used to view other events (older) that have occurred and are active (not yet cleared).

[ENTER/STORE]

See individual mode descriptions in other sections of this manual.

4.2 Displays

Four 7-segment red LED characters provide visual annunciation of status, events and messages. A list of messages
that may appear on the display in Normal Mode is shown below:

d__1
d__2
d__3
d__4
d__5
E__1
E__2
E__3
E__4
E__5
A__1
A__2
A__3
A__4
A__5

Zone 1 Disabled
Zone 2 Disabled
Zone 3 Disabled
Zone 4 Disabled
Zone 5 Disabled
Zone 1 Enabled
Zone 2 Enabled
Zone 3 Enabled
Zone 4 Enabled
Zone 5 Enabled
Alarm Zone 1
Alarm Zone 2
Alarm Zone 3
Alarm Zone 4
Alarm Zone 5

F__1
F__2
F__3
F__4
F__5
F__A
F__E
Lo_b
no_b
PH_1
PH_2
bEL1
bEL2
no_1
no_2

Trouble Zone 1
Trouble Zone 2
Trouble Zone 3
Trouble Zone 4
Trouble Zone 5
Annunciator Fault
Earth Fault
Low Battery
No Battery
Primary C.S.# Comm. Fault
Secondary C.S. # Comm. Fault
Bell 1 Fault or Disabled
Bell 2 Fault or Disabled
Primary Phone Line Fault
Secondary Phone Line Fault

SUP1
SUP2
SUP3
SUP4
SUP5
_AC_
rES_

Supv. Alarm Zone 1
Supv. Alarm Zone 2
Supv. Alarm Zone 3
Supv. Alarm Zone 4
Supv. Alarm Zone 5
AC Power Loss
System Reset

Document #15140 Rev.G 01/02/02 P/N 15140:G

51

Displays

Individual LEDs are provided for:

System Alarm

A red LED that turns on steady when an alarm condition is detected and blinks during the alarm presignal period.

System Trouble

This yellow LED blinks to indicate that a fault or abnormal condition exists and that the fire alarm system may be
inoperative. It turns on steady when the silence switch is pressed.

AC Power On

A green LED that remains on while the AC power supply is within correct limits. If this indicator fails to light under
normal conditions, service the system immediately.

Supervisory

A yellow LED that blinks to indicate the need for action in connection with the supervision or maintenance of sprin­klers, extinguishing systems or other protective systems.

System Silence

A yellow LED that turns on to indicate that an alarm or trouble condition exists in the system, but both NACs (if pro­grammed as silenceable) and local piezo have been silenced.

Primary Line Active

A red LED on the main circuit board that indicates the primary phone line is active.

Secondary Line Active

A red LED on the main circuit board that indicates the secondary phone line is active.

Kissoff

A green LED on the main circuit board that blinks when a Central Station has acknowledged receipt of each transmit­ted message or when a portion of upload or download data has been accepted from a Service Terminal.

Modem

A green LED on the main circuit board that stays on steady during modem types of communications.

FIGURE 4-1:

Phone Connectors and LEDs

Primary Line

Primary Active

Secondary Line

Secondary Active

52

Modem LED

Kissoff LED

Document #15140 Rev.G 01/02/02 P/N 15140:G

Operation

4.3 Operation

Normal Mode is the standard mode of operation. In this mode, the control panel continuously monitors system status.
When no alarm or trouble conditions exist, the display will be blank and all LEDs will be off (except the AC Power
LED). The Notifications Appliance Circuits will be off, all relays and relay drivers are normal and the onboard piezo
sounder will be off. The communicator is not active, primary and secondary active LEDs are off.

All alarm and system trouble conditions are annunciated on the control panel's display. The control panel will main­tain an 'active event list' which will consist of all alarms, supervisory alarms and system troubles currently active and
not cleared, requiring immediate service. When the system is cleared and restored to normal, the display will be
blank. All alarms and troubles are stored in a history file and may be recalled at any time.

Higher priority events take precedence over lower priority events. Display and reporting of system status is done on
a priority basis. Priorities are, from highest to lowest:

Alarms

1.

Supervisory Alarms

2.

System Troubles

3.

If the events to be displayed consist only of alarms and disabled zones (no troubles), the control panel will scroll them
on the display. Pressing the 1st Event key will stop the scrolling and cause the display of the first alarm that occurred
after the panel was last reset, cleared of all active events and placed into Normal Mode. Operation of the Up and
Down arrow keys will display all remaining events in sequence.

If events to be displayed include system troubles, only one event is displayed at a time and there is no scrolling. The
event displayed is the highest priority. Pressing the 1st Event key will cause the display of the first event that
occurred after the panel was last reset, cleared of all active events and placed into Normal Mode. Operation of the Up
and Down arrow keys will display all remaining events in order of their occurrences.

4.3.1 Alarm Response

Upon detection of an alarm condition, the control panel will:

✓ Turn the alarm LED on

✓ Activate the alarm relay

✓

Display the alarm message (i.e. A__1 for alarm on zone 1)

✓

Communicate the alarm to the Central Station

✓ Store the alarm in the History file

✓ Turn the NACs on

✓ Turn the piezo sounder on

✓ Turn on appropriate zone relay output

✓ Output alarm message to printer

✓ Terminate upload or download communications

Note that when any zone is programmed as a supervisory zone, it will not be processed in the same manner as a con­ventional alarm zone. See Supervisory Condition later in this section.

Document #15140 Rev.G 01/02/02 P/N 15140:G

53

Operation

4.3.2 Alarm Restoral

The control panel returns to normal only after all alarms have been cleared and the Reset switch has been pressed
(pull stations reset, smoke detectors reset and no smoke is present, waterflow has stopped, etc.). Upon restoral of all
active alarms, the control panel will perform the following:

✓ Turn off the alarm LED

✓ Deactivate the alarm relay

✓ Clear the 4-character display

✓ Send all 'zone restoral' messages to the Central Station

✓ Turn off the NACs

✓ Turn off the piezo sounder

✓ Turn off appropriate zone relay output

✓ Output 'zone restoral' message to printer

✓ Terminate upload or download communications

4.3.3 System Supervisory Condition Response

Program zones for supervisory in applications where a waterflow sensing device has been employed and the wiring to
the waterflow valve and/or a tamper switch is to be monitored. If the tamper switch has been activated (normally
open contacts close), a supervisory alarm condition will occur. When a supervisory condition occurs, the control
panel will:

✓

Blink the supervisory LED (½ second On, ½ second Off)

✓

Activate the supervisory relay driver (TB4-5)

✓

Display the following message: SUPX where X = the zone number

✓

Communicate the supervisory condition to the Central Station

✓

Store the 'supervisory' message in the History file

✓

Pulse the piezo sounder at ½ second On and ½ second Off rate

✓

Turn on appropriate zone relay output

✓

Output system supervisory message to printer

✓

Terminate upload or download communications

4.3.4 System Supervisory Restoral Response

When the supervisory condition has been cleared (condition is restored and the reset switch has been pressed), the
control panel will perform the following:

✓ Turn off the supervisory LED

✓ Deactivate the supervisory relay driver (TB4-5)

✓ Clear the display of the 'SUP' message

✓

Communicate a supervisory restoral message to the Central Station

✓

Shut off the piezo sounder

✓

Turn off appropriate zone relay output

✓

Output system supervisory restoral message to printer

✓

Terminate upload or download communications

Note: For any zone programmed for supervisory autoresettable, the Reset switch does not need to be pressed to clear
the zone (supervisory condition).

54

Document #15140 Rev.G 01/02/02 P/N 15140:G

Operation

4.3.5 Trouble Condition Response

Upon detection of one or more trouble conditions, the control panel will perform the following:

✓ Blink the trouble LED (1 second On and 1 second Off)

✓ Activate the trouble relay

✓ Display the appropriate trouble message(s) in priority fashion from the highest priority to the lowest.

Note that the Up Arrow, Down Arrow or 1st Event key must be pressed to view the messages

✓ Communicate the trouble conditions to the Central Station

✓ Store the trouble conditions in the History file

✓ Sound the piezo sounder 1 second On and 1 second Off

✓ Output the system trouble messages to the printer

✓ Terminate upload or download communications

Note: When AC brownout occurs, the AC LED is turned off and the trouble LED blinks. Should the brownout con­dition remain, it will be transmitted to the Central Station after a delay (see program address 64).

Possible trouble messages that may appear on the display are as follows:

d__1
d__2
d__3
d__4
d__5
F__1
F__2
F__3
F__4
F__5
F__A
F__E

Zone 1 Disabled
Zone 2 Disabled
Zone 3 Disabled
Zone 4 Disabled
Zone 5 Disabled
Trouble Zone 1
Trouble Zone 2
Trouble Zone 3
Trouble Zone 4
Trouble Zone 5
Annunciator Fault
Earth Fault

Lo_b
no_b
PH_1
PH_2
bEL1
bEL2
no_1
no_2
_AC_

Low Battery
No Battery
Primary C.S.# Comm. Fault
Secondary C.S. # Comm. Fault
Bell 1 Fault or Disabled
Bell 2 Fault or Disabled
Primary Phone Line Fault
Secondary Phone Line Fault
AC Power Loss (shown only when requested)

4.3.6 Trouble Condition Restoral

Upon restoral of all trouble conditions, the control panel performs the following:

✓ Shut off the trouble LED

✓ Deactivates the trouble relay

✓ Turn off the AC Power LED if the trouble was loss of AC

✓

Clear the display of all trouble messages

✓

Communicate the restored trouble condition(s) to the Central Station

✓

Output the system trouble restoral message to the printer

✓

Terminate upload or download communications

4.3.7 Off Normal Reporting

Removing the control panel from Normal Mode and placing it into any other mode causes the transmission of an 'off
normal' fault message to the Central Station. Returning the panel to Normal Mode causes the transmission of a
'return to normal' restoral message.

Document #15140 Rev.G 01/02/02 P/N 15140:G

55

Operation

4.3.8 Zone Disable/Enable

The zone disable feature may be used to disable any zone in the system. Zones may be disabled if they are normal, in
trouble or alarmed. Zones may be disabled only during the Normal Mode of operation, when the fire protection is

active. If the panel is in alarm, the silence switch must be pressed first, before the zone disable feature will function.

To disable a zone, press the MODE key once (the display will go blank). You then have 10 seconds to start entering
the code 3472. Next press the [ENTER/STORE] key.

3472 spells DISA on a Touch-Tone

☛

A flashing lower case d will appear on the far left of the display. Press the digit key corresponding to the zone num­ber to be disabled. The number will appear on the far right of the display. Press [ENTER/STORE] to disable the
zone. Note that the trouble relay is activated and the trouble LED blinks.

The zone disable message will remain on the display until the zone is reenabled. To reenable a zone, press the

MODE key. The display will go blank. You then have 10 seconds to start entering the code 3622. Next, press the
[ENTER/STORE] key.

3622 spells ENAB on a Touch-Tone

☛

A flashing upper case E will appear on the left of the display. Press the digit key corresponding to the zone number to
be enabled. The number will appear on the far right of the display. Press the [ENTER/STORE] key to reenable the
zone. Not that the trouble relay is restored to normal and the trouble LED turns off (if no other troubles are on the
system).

®

phone.

®

phone.

4.3.9 Fire Drill

The Drill (manual evacuate) feature turns on both Notification Appliance Circuits (if programmed as enabled) and
turns off the silence LED. Tor perform a fire drill, press the MODE key followed by the code 3745 then the
[ENTER/STORE] key. The display will indicate dril. The alarm relay is not activated for a fire drill. There is an
option to transmit the fire drill report code to the Central Station.

3745 spells DRIL on a Touch-Tone

☛

During a fire drill, the Silence key will silence both NACs and the Reset key restores the control panel to normal. All
zones remain active during a fire drill.

®

phone.

56

Document #15140 Rev.G 01/02/02 P/N 15140:G

Central Station Communications

4.4 Central Station Communications

The control panel transmits zone and system status reports to Central Stations via the public switched telephone net­work. Two supervised telephone line connections are made to interface the control panel to the telephone lines. Two
optional 7 foot telephone cords are available for this purpose and can be purchased separately.

The control panel supervised both telephone lines for proper voltage. A delay of two minutes will occur before a
fault in either phone line connection is reported as a trouble. When a fault is detected, an audible trouble signal will
sound, the yellow trouble LED will blink, the 4-character display will show either 'no 1' (primary line fault) or 'no 2'
(secondary line fault) and the trouble condition will be reported to the Central Station over the remaining operational
phone line.

The control panel comes with line seizure capability provided for both the primary and secondary telephone line
interfaces. Any time that the control panel needs to make a call to a Central Station, line seizure will disconnect any
local premises phones sharing the same telephone line.

All transmissions to the Central Stations will be sent over the primary phone line. In the event of noisy phone lines,
transmissions will be sent over the backup secondary phone line.

Two phone numbers must be programmed, the primary Central Station phone number and the secondary Central Sta­tion phone number. All system reports will be transmitted to the primary Central Station phone number. Reports will
automatically be sent to the secondary Central Station phone number if attempts to transmits to the primary Central
Station phone number are unsuccessful. If 10 total attempts to communicate are unsuccessful, the Communicator
Failure output will be turned on (TB4, Terminal 6). Note that as an option, all reports may also be sent to the second­ary Central Station phone number.

The MS-5024UD meets NFPA 72 National Fire Code reporting requirements for: (a) the type of signal, (b) condition
and (c) location of the reporting premises. The general priority reporting structure is:

Zone Alarms and Restores

1.

Zone Troubles and Restores

2.

System Troubles and Restores

3.

24-hour Test

4.

Document #15140 Rev.G 01/02/02 P/N 15140:G

57

Central Station Communications

The control panel is capable of reporting detailed messages depending upon the format in use. Table 4-1 shows the
reporting structure for all formats.

TABLE 4-1:

Zone Trouble Restore SSS(S) RTZ

System Trouble SSS(S) TS

System Trouble Restore SSS(S) RTS

Zone Disable Restore SSS(S) RDZ

Format Selection Address (16 & 42)

Format #

0, 2, 4, 6, 8

Report

Alarm SSS(S) A

Alarm Restore SSS(S) RA

Zone Trouble

(Zone Open)

Zone Disable SSS(S) DZ

3+1/4+1/Standard

4+1 Express

SSS(S) TZ

Format #

3, 5, 7, 9

3+1/4+1/Expanded

SSS(S) A

AAA(A) Z

SSS(S) RA

RARARA(RA) Z

SSS(S) TZ

TZTZTZ(TZ) Z

SSS(S) RTZ

RTZ RTZRTZ(RTZ ) Z

SSS(S) TS

TSTSTS(TS) Y

SSS(S) RTS

RTS RTSRTS(RTS ) Y

SSS(S) DZ

DZDZDZ(DZ) Z

SSS(S) RDZ

RDZRDZRDZ(RDZ) Z

Format #

1, A, C

4+2/Standard

4+2 Express

Format

B, D

4+2/Expanded

SSSS AA2 SSSS AZ

SSSS RARA2 SSSS RAZ

SSSS TZTZ2 SSSS TZZ

SSSS RTZRTZ2 SSSS RTZZ

SSSS TSTS2 SSSS TSY

SSSS RTSRTS2 SSSS RTSY

SSSS DZDZ2 SSSS DZZ

SSSS RDZRDZ2 SSSS RDZZ

Low Battery SSS(S) L SSS(S) L SSSS LL2 SSSS LL2

Low Battery Restore SSS(S) RL SSS(S) RL SSSS RLRL2 SSSS RLRL2

AC Loss SSS(S) P SSS(S) P SSSS PP2 SSSS PP2

AC Loss Restore SSS(S) RP SSS(S) RP SSSS RPRP2 SSSS RPRP2

Fire Drill SSS(S) Fd SSS(S) Fd SSSS FdFd2 SSSS FdFd2

Fire Drill Restore SSS(S) RFd SSS(S) RFd SSSS RFdRFd2 SSSS RFdRFd2

Supervisory Condition SSS(S) V

Supervisory Condition

Restore

SSS(S) RV

SSS(S) V

VVV(V) Z

SSS(S) RV

RVRVRV(RV ) Z

SSSS VV2 SSSS VZ

SSSS RVRV2 SSSS RVZ

Test Report SSS(S) X SSS(S) X SSSS XX2 SSSS XX2

Upload or Download SSS(S) UD SSS(S) UD SSS UDUD2 SSS UDUD2

Refer to Table 4-2 for an explanation of each letter code in Table 4-1 . Refer to Table 4-3 for a list of compatible
receivers.

58

Document #15140 Rev.G 01/02/02 P/N 15140:G

Central Station Communications

TAB LE 4- 2:

Format Selection Address Explanation

Where

SSS or SSSS = Subscriber ID
A = Alarm (1st digit)
A2 = Alarm (2nd digit)
Z = Zone Number
RA = Alarm Restore (1st digit)
RA2 = Alarm Restore (2nd digit)
TZ = Zone Trouble (1st digit)
TZ2 = Zone Trouble (2nd digit)
RTZ = Zone Trouble Restore (1st digit)
RTZ2 = Zone Trouble Restore (2nd digit)
TS = System Trouble (1st digit)
TS2 = System Trouble (2nd digit)
RTS = System Trouble Restore (1st digit)
RTS2 = System Trouble Restore (2nd digit)
DZ = Zone Disable (1st digit)
DZ2 = Zone Disable (2nd digit)
RDZ = Zone Disable Restore (1st digit)
RDZ2 = Zone Disable Restore (2nd digit)
L = Low Battery (1st digit)
L2 = Low Battery (2nd digit)
RL = Low Battery Restore (1st digit)
RL2 = Low Battery Restore (2nd digit)
P = AC Loss (1st digit)
P2 = AC Loss (2nd digit)
RP = AC Loss Restore (1st digit)
RP2 = AC Loss Restore (2nd digit)
FD = Fire Drill (1st digit)
FD2 = Fire Drill (2nd digit)
RFD = Fire Drill Restore (1st digit)
RFD2 = Fire Drill Restore (2nd digit)
V = Supervisory Condition (1st digit)
V2 = Supervisory Condition (2nd digit)
RV = Supervisory Condition Restore (1st digit)
RV2 = Supervisory Condition Restore (2nd digit)
X = Test Report (1st digit)
X2 = Test Report (2nd digit)
Y = A trouble corresponding to the following:

7 = Ground Fault
8 = Low Battery
9 = No Battery

A = Telco Primary Line Fault

B = Telco Secondary Line Fault
C = Main Bell Fault, Annunciator Bell

D = Communication Fault to Primary Number

E = Communication Fault to Secondary Number

F = System Off Normal Fault/System Fault (Slave Operation, see Chapter 6)
UD = Upload/download (1st digit)
UD2 = Upload/download (2nd digit)

Note: For Expanded Reporting, the control panel automatically adds the digit corresponding to the zone number and
the second digit corresponding to any system trouble condition. Only the first digit is programmable.

Document #15140 Rev.G 01/02/02 P/N 15140:G

59

Central Station Communications

4.4.1 Transmittal Priorities

The integral communicator transmits highest priority events first. Events, in terms of priority, are listed below in
descending order:

Alarms (highest priority level)

1.

✓ Pull stations

✓ Waterflow

✓ Smoke detector

✓ Other alarm types

Supervisory Zone

2.

System Troubles

3.

✓ Zone disabled

✓ Fire drill

✓ AC fail (after delay)

✓ Zonal faults

✓ Earth fault

✓ Low battery/no battery

✓ Telephone line fault

✓ Notification Appliance Circuits fault

✓ Communication trouble

✓ Annunciator trouble

✓ System off normal

Restoral Reports

4.

✓ Zone alarm

✓ Supervisory

✓ Zone(s) enabled

✓ Fire drill

✓ AC

✓

Zone fault

✓

Earth

✓ Battery

✓ Telephone line

✓ Notification Appliance Circuits

✓ Communication

✓ Annunciator trouble

✓ System off normal

24 Hour Test (lowest priority)

5.

Red LEDs are provided on the control panel circuit board to identify which telephone line is activated. Also, a green
LED labeled 'kissoff' will turn on whenever the control panel has successfully transmitted reports to the Central Sta­tion. The 'kissoff' LED may turn on several times during communications with a Central Station.

60

Document #15140 Rev.G 01/02/02 P/N 15140:G

Central Station Communications

The table below shows UL listed receivers which are compatible with the MS-5024UD.

TAB LE 4- 3:

0 4+1 Ademco Express

1 4+2 Ademco Express

2 3+1/Standard/1800/2300

3 3+1/Expanded/1800/2300

4 3+1/Standard/1900/1400

5 3+1/Expanded/1900/1400

6 4+1/Standard/1800/2300

7 4+1/Expanded/1800/2300

8 4+1/Standard/1900/1400

9 4+1/Expanded/1900/1400

A 4+2/Standard/1800/2300

B 4+2/Expanded/1800/2300

C 4+2/Standard/1900/1400

D 4+2/Expanded/1900/1400

E Ademco Contact ID

FNot Used

Compatible UL Listed Receivers

Format #

(Addresses 16 & 42)

Ademco

685 (1)

Silent Knight

9000 (2)

ITI

CS-4000 (3)

FBI

CP220FB

Osborne Hoffman

Models 1 & 2

Radionics

6000 (6)

Radionics

6500 (5)

Sescoa

3000R (7)

Surguard

MLR-2 (9)

✔✔ ✔

✔✔✔

✔✔ ✔✔

✔✔ ✔✔

✔✔ ✔

✔✔ ✔

✔✔ ✔✔

✔✔ ✔

✔✔ ✔

✔✔ ✔

✔✔ ✔✔

✔✔ ✔

✔✔ ✔

✔✔ ✔

(4)

(4)

(4)

(4)

(4)

(4)

(4)

(4)

(4)

(4)

(4)

(4)

(8)

✔

✔✔✔✔✔

✔✔✔

✔✔✔

✔✔✔

✔✔✔✔

✔✔✔

✔✔✔

✔✔✔

✔✔✔✔

✔✔✔

✔✔✔

✔✔✔

✔✔✔ ✔

With 685-8 Line Card with Rev. 4.4d software

1.

With 9002 Line Card Rev. 9035 software or 9032 Line Card with 9326A software

2.

Rev. 4.0 software

3.

FBI CP220FB Rec-11 Line Card with Rev. 2.6 software and a memory card with Rev. 3.8 software

4.

Model 6500 with Rev. 600 software

5.

Mode 6000 with Rev. 204 software

6.

With Rev. B control card at Rev. 1.4 software and Rev. C line card at Rev. 1.5 software

7.

Model 2 only

8.

Version 1.62 software

9.

Document #15140 Rev.G 01/02/02 P/N 15140:G

61

Servicing

CHAPTER 5 Servicing

5.1 Walktest Mode

The MS-5024UD provides the capability to perform a one-man walktest of the system without triggering the commu­nicator, the zone relays or the alarm output relay. Walktest allows for testing of the five zones (Initiating Device Cir­cuits). The first initiating device activated on a zone will cause the Notification Appliance Circuits to turn on for four
seconds. Subsequent device activations on the same zone will cause the NACs to turn on for one second. Any smoke
detectors that are activated will be reset. Zonal faults (open circuits) will cause the NAC to remain on steady. Prior
to entering Walktest Mode, check to be certain that all system faults have been cleared. Note that the trouble relay

will be activated while the control panel is in Walktest Mode. Placing the control panel into this mode will only be
possible if the system has no active alarms.

Pressing the MODE key followed by the 4-digit code 9255 and then the [ENTER/STORE] key will place the con­trol panel into Walktest Mode.

9255 spells WALK on a Touch-Tone

☛

®

phone.

Once in Walktest Mode, the control panel will immediately:

✓

Blink the trouble LED

✓

Activate the trouble relay

✓

Turn on the NACs for four seconds for the first alarm on a zone. Subsequent alarms on the same zone
will sound for one second. Troubles cause the NACs to remain on

✓

Disable the alarm relay

✓

Display all alarm conditions as they occur

✓

Display all zone troubles as they occur

✓

Display ground faults as they occur

✓

Transmit 'off normal' message to Central Station(s)

✓

Continue to communicate any events not acknowledged at a Central Station prior to entering Walktest
Mode

During Walktest Mode, zonal activity is displayed in real-time as it occurs. At the end of walktesting the system, the
display will show the last event that occurred. To view all events stored during Walktest, use the Up arrow, Down
arrow and 1st Event keys. The Down arrow key moves the Walktest list to show older (previous) events. The Up
arrow key moves the Walktest list to show newer (more recent) events. Pressing the 1st Event key at any time will
cause the display of the first event stored upon initial entry into Walktest Mode. While in Walktest Mode, the control
panel will store up to 128 events in the Walktest File for later recall and display. A printer may be connected to the
panel during Walktest. All Walktest events are printed in real-time as they occur.

To return the control panel to Normal Mode, press the MODE key followed by the code 6676 and then the [ENTER/
STORE] key. Any delay between key presses greater than 10 seconds causes the control panel to remain in Walktest
Mode.

The control panel will automatically return to Normal Mode if no system activity has occurred for 60 minutes. This
includes pressing any keys or activity on any zone. Exiting Walktest Mode leaves the Walktest file in memory such
that it may be printed in Print Mode. Subsequent entries into Walktest Mode will delete the Walktest file.

Note that remote site upload or download is not possible while in Walktest Mode.

62

Document #15140 Rev.G 01/02/02 P/N 15140:G

History Mode

5.2 History Mode

All Normal Mode events are stored in a History File list for future recall. Recall is possible via the 4-character dis­play or via an optional printer. The History File list is a first-in, first-out (FIFO) file. In this manner, only the most
recent events may be called up from memory. Older events will be overwritten, that is, pushed out of the FIFO file.
The number of stored events is 32 maximum. The History File is kept in E
erase the list.

Pressing the MODE key followed by the code 4478 and then the [ENTER/STORE] key places the control panel into
History Mode. This will not occur if there are any active alarm conditions present. The event displayed, is the most
recent event.

4478 spells HIST on a Touch-Tone

☛

®

phone.

Once in History Mode, the control panel will:

✓

Blink the trouble LED

✓

Activate the trouble relay

✓ Disable the Notification Appliance Circuit(s)

✓ Disable the alarm relay

✓ Display all events as they occurred since the last time the History File list was cleared. The most recent

event will be displayed first

✓ Ignore all other keys other than those mentioned in this section

✓ Transmit the 'off normal' message to the Central Station(s)

✓ Continue to communicate any events not previously acknowledged at the Central Station prior to enter-

ing History Mode

2

memory. Complete power loss will not

The Down Arrow key moves the History File to show older (previous) events. The Up Arrow key moves the History
file to show newer (more recent) events. Following is a list of messages as they will appear on the display:

d__1
d__2
d__3
d__4
d__5
E__1
E__2
E__3
E__4
E__5
A__1
A__2
A__3
A__4
A__5

Zone 1 Disabled
Zone 2 Disabled
Zone 3 Disabled
Zone 4 Disabled
Zone 5 Disabled
Zone 1 Enabled
Zone 2 Enabled
Zone 3 Enabled
Zone 4 Enabled
Zone 5 Enabled
Alarm Zone 1
Alarm Zone 2
Alarm Zone 3
Alarm Zone 4
Alarm Zone 5

F__1
F__2
F__3
F__4
F__5
F__A
F__E
Lo_b
no_b
PH_1
PH_2
bEL1
bEL2
no_1
no_2

Trouble Zone 1
Trouble Zone 2
Trouble Zone 3
Trouble Zone 4
Trouble Zone 5
Annunciator Fault
Earth Fault
Low Battery
No Battery
Primary C.S.# Comm. Fault
Secondary C.S. # Comm. Fault
Bell 1 Fault or Disabled
Bell 2 Fault or Disabled
Primary Phone Line Fault
Secondary Phone Line Fault

SUP1
SUP2
SUP3
SUP4
SUP5
_AC_
SILE
rES_

Supv. Alarm Zone 1
Supv. Alarm Zone 2
Supv. Alarm Zone 3
Supv. Alarm Zone 4
Supv. Alarm Zone 5
AC Power Loss
Silence Switch Pressed
Reset Switch Pressed

It should be noted that setting the time and date may cause corruption of the History File contents. The History File
should therefore be cleared after the time and date are set. To clear the list from E

2

memory, press the SILENCE key

twice before exiting the History Mode.

A lack of keyboard activity for a period of 10 minutes will cause the control panel to return to Normal Mode. If a
printer is connected to the control panel, the History File will be printed upon successful entry into History Mode and
a list of the most recent 32 events, time and date stamped, will print out. Note that remote site upload or download is

not possible while the panel is in History Mode.

Document #15140 Rev.G 01/02/02 P/N 15140:G

63

Troubleshoot Mode

5.3 Troubleshoot Mode

In Troubleshoot Mode, system voltages may be displayed on the 4-character display. An internal voltmeter measures
the voltage present at:

• Zone inputs

• AC power input

• Battery terminal leads

•NAC #1

•NAC #2

• Resettable 24 volt power output

To enter Troubleshoot Mode, press the MODE key followed by the code

and then the [ENTER/STORE] key.

8768

A lack of keyboard activity for a period of 20 minutes will cause the control panel to return to Normal Mode.

8768 spells TROU on a Touch-Tone

☛

®

phone.

Once in Troubleshoot Mode, the control panel will:

✓

Blink the trouble LED

✓

Activate the trouble relay

✓

Disable the NACs

✓

Disable the alarm relay

✓

Transmit the 'off normal' message to the Central Station(s)

✓

Continue to communicate any events not yet acknowledged at the Central Station prior to entering
Troubleshoot Mode

Voltages can be viewed by performing the following steps:

• AC input voltage - press A and then the [ENTER/STORE] key

• Battery voltage - press B and then the [ENTER/STORE] key

• Zone 1 voltage - press 1 and then the [ENTER/STORE] key

• Zone 2 voltage - press 2 and then the [ENTER/STORE] key

• Zone 3 voltage - press 3 and then the [ENTER/STORE] key

• Zone 4 voltage - press 4 and then the [ENTER/STORE] key

• Zone 5 voltage - press 5 and then the [ENTER/STORE] key

• NAC #1 voltage - press b then 1 and then the [ENTER/STORE] key

• NAC #2 voltage - press b then 2 and then the [ENTER/STORE] key

• Resettable 24 volt power - press the RESET key and then the [ENTER/STORE] key

5.3.1 Zone Voltages

The nominal threshold voltages for each zone are listed below. Actual readings will vary depending upon system load
and AC line voltage

TABLE 5-1:

Zone # Normal w/E.O.L. Shorted Open Circuit

1 23.5V 0.00V 25.4V

2 23.5V 0.00V 25.4V

3 23.5V 0.00V 25.4V

4 23.5V 0.00V 25.4V

5 23.5V 0.00V 25.4V

64

.

Nominal Zone Voltages

Document #15140 Rev.G 01/02/02 P/N 15140:G

Troubleshoot Mode

5.3.2 AC Line Voltage

The following table lists the AC line voltage range. The AC On indicator will turn off when the AC line voltage
drops below the Low Line threshold and the trouble LED will turn on.

TAB LE 5- 2:

AC Line Voltage Low Line Normal High Line

AC Line Voltage Range

MS-5024UD 102 VAC 115 VAC 132 VAC

MS-5024UDE 204 VAC 220 VAC 264 VAC

5.3.3 Battery Voltage

The following table lists the critical battery threshold conditions. Note that battery measurements should be made
after allowing 48 hours to charge depleted batteries. If batteries do not show normal readings, replace them.

IMPORTANT

: The battery charger will turn off when the battery voltage drops to 17.4 VDC or less (No Battery

condition). A battery with a higher voltage must be installed to turn the charger back on.

TAB LE 5- 3:

Battery Voltage

Normal Low Battery No Battery

Battery Voltage: 27.6V 20.4V <17.4V

5.3.4 Telephone Lines

Pressing C for touchtone dialing or D for rotary dialing, followed by [ENTER/STORE] causes seizure of the pri­mary phone line which in turn lights the red LED signifying primary phone line active. After a delay of three sec­onds, the control panel goes off-hook to acquire a dial tone.

The control panel keypad may be used as a telephone touchpad for number dialing. Once the first digit is pressed, the
display will move the C or D character one position to the left, while placing the digit to be dialed on the farthest right
display position. Continue to press the phone numbers to be dialed. Successive depressions of the [ENTER/
STORE] key hangs up and picks up the phone (places the phone on or off the hook).

The secondary phone line may be tested by pressing the E key for touchtone dialing or the F key for rotary dialing
and then following the same procedure used for the primary phone line.

A handset may be temporarily connected across transformer T1 as indicated in Figure 5-1. The handset, when con­nected across T1, may be used only as an amplifier/speaker and telephone with the control panel used for number
dialing.

FIGURE 5-1:

Phone Connectors and LEDs

Both Primary and Secondary Lines

Document #15140 Rev.G 01/02/02 P/N 15140:G

65

Lamp Test

5.3.5 NAC 1 & 2

NAC voltage readings are nominally -2.32 volts when an EOL resistor of correct value is in place. A reading of 0.00
volts appears for shorts, -4.50 volts for opens. Intermediate readings are also available.

Note that remote site upload or download is not possible while the panel is in Troubleshoot or Lamp Test Mode.

5.3.6 Resettable Power

Resettable 24 volt power output must read 24 volts, + or - 10%.

5.4 Lamp Test

To perform a Lamp Test, press MODE then the code 5267 followed by the [ENTER/STORE] key. This will test all
system LEDs. The LEDs will remain on for five seconds and then the control panel will return to Normal Mode.

5267 spells LAMP on a Touch-Tone

☛

®

phone.

5.5 Print Mode

A printer may be temporarily or permanently connected to the control panel. Refer to Figure 2-15 on page 30, for
proper PRT-24 Printer Interface module connection to the main circuit board before proceeding.

Programmable option address 78 must be programmed to a '2' if only a printer is connected to the control panel or '3'
if both a printer and annunciator are connected to the control panel, to enable printer supervision. Once enabled, nor­mal system status as well as panel operations will be printed. If the printer connection is removed, the trouble LED
will blink, the piezo sounder will pulse and the 4-character LED display will be blank.

Select Printer Mode by pressing the MODE key followed by the code 7746 and then the [ENTER/STORE] key.
The display will read Prn and the following will be printed:

Entire program entries

1.

History file

2.

Walktest file

3.

Troubleshoot Mode voltages

4.

Current system status

5.

(Note that all activity is time and date stamped)

Upon entering the Print Mode, the control panel will transmit the 'system off normal' message to the Central Station.
The panel will return to Normal Mode automatically after printing is completed. This will typically take three
minutes.

Note that remote site upload or download is not possible while the panel is in Print Mode.

66

Document #15140 Rev.G 01/02/02 P/N 15140:G

Slave Communicator Configuration

CHAPTER 6 Slave Communicator Configuration

The MS-5024UD may be used as a slave communicator to a host or master FACP (fire alarm control panel). All wir­ing between the master and the slave communicator is supervised. 4.7K ohm End-of-Line resistors should be
connected.

In slave configuration, the five zones become five channels that may be triggered by the relay outputs of any host
FACP. The five channels function as follows:

• Zone/Channel 1 - general alarm

• Zone/Channel 2 - general trouble

• Zone/Channel 3 - may be programmed to match the FACP relay function

• Zone/Channel 4 - supervisory

• Zone/Channel 5 - may be programmed to match the FACP relay function

The factory settings for Zone/Channel 2 alarm and restoral are altered as follows:

•If 0, 2, 3, 4, 5, 6, 7, 8, 9, B or D is entered for address 16 or 42, the report code for Zone 2 Alarm Code
(address 128 & 252) is 'F' and the Zone 2 Restoral Code (address 156 & 280) is 'E'.

•If 1, A or C is entered for addresses 16 or 42, the report code for Zone 2 Alarm Code (addresses 129-130 &
253-254) is 'FF' and the Zone 2 Restoral Code (addresses 185-186 & 309-310) is 'EF.'

•If E is entered for addresses 16 or 42, the report code for Zone 2 Alarm Code and Restoral Code (addresses
130-132 & 254-256) is ‘300.’

The factory settings for Zone/Channel 4 alarm and restoral are altered as follows:

•If 0, 2, 3, 4, 5, 6, 7, 8, 9, B or D is entered for address 16 or 42, the report code for Zone 4 Alarm Code
(address 130 & 254) is '8' and the Zone 4 Restoral Code (address 158 & 282) is 'E'.

•If 1, A or C is entered for addresses 16 or 42, the report code for Zone 4 Alarm Code (addresses 133-134 &
257-258) is '84' and the Zone 4 Restoral Code (addresses 189-190 & 313-314) is 'E4.'

•If E is entered for addresses 16 or 42, the report code for Zone 4 Alarm Code and Restoral Code (addresses
136-138 & 260-262) is ‘200.’

Location 56 must be programmed to a '1' to enable the control panel as a slave communicator.

Note that remote site upload or download is permitted in the Slave Communicator configuration, however, alarm
presignal and verification do not function in Slave mode.

Be certain to connect the slave communicator's primary AC power to the same branch circuit as the host FACP.

Document #15140 Rev.G 01/02/02 P/N 15140:G

67

Slave Communicator Configuration

FIGURE 6-1:

Slave Communicator Connections

Relays in the master FACP activate various input circuits on the slave communicator. Messages (event codes) pro­grammed for a particular input circuit (channel) will be transmitted to the Central Station upon relay activation.

68

Document #15140 Rev.G 01/02/02 P/N 15140:G

Remote Site Upload/Download

CHAPTER 7 Remote Site Upload/Download

The control panel may be programmed or interrogated off-site via the public switched telephone network. Any per­sonal computer with DOS

™

4.01 or greater plus Windows™ 3.1 or greater, with a 1200 baud Hayes™ compatible
modem and Fire•Lite Upload/Download software P/N PK-5024UD, may serve as a Service Terminal. This allows
download of the entire program or upload of the entire program, history file, walktest data, current status, system
voltages, time and date.

CAUTION: After successfully downloading a program, make certain to perform the following steps:

Print out all programmed data via Print Mode or manually view programmed entries and compare to intended

1.

program data

Test all affected panel operations

2.

Immediately correct any problems found

3.

7.1 Downloading Program

The first time that the control panel is downloaded (whether initiated at the jobsite or remotely), a secret code is
loaded in by a Service Terminal. Future upload or download requests cause verification of the secret code by the con­trol panel before processing of data is allowed. If the secret code is not verified, the control panel will terminate the
request.

While the control panel is communicating with the Service Terminal, the panel's green Modem LED and one of the
red Line Seize LEDs will remain on steady. At the conclusion of a successful download, the green Kissoff LED will
turn on steady for five seconds, the green Modem LED will turn off and the red Line Seize LED will turn off.

In order to download the panel (whether initiated at the jobsite or remotely), the following must be true:

✓

The control panel must be in the Normal Mode of operation. Downloading is not possible if the panel is
in any other mode

✓

There cannot be any active communications ongoing with a Central Station receiver

✓

All active events must be successfully 'kissed-off' by the Central Station(s). The communicator must be
in a standby state with no new information waiting to be transmitted to a Central Station

With program address location 56 set to '1' or '2', anytime a download is initiated, the control panel will first contact
the primary Central Station or both the primary and secondary Central Stations to report a 'request for upload/down­load' message. Once the request is 'kissed-off' by the Central Station(s), the control panel will then call the appropri­ate Service Terminal and begin the downloading process.

To prevent the 'request for upload/download' message(s) from being reported to the Central Station(s), make certain
to leave address 56 set to '0' or disable all upload/download reports back to both Central Stations.

During the downloading process, the fire protection remains active

. Should a system trouble or alarm condition
occur, the control panel immediately terminates downloading and processes the trouble or alarm locally and trans­mits the information to the Central Station(s).

Document #15140 Rev.G 01/02/02 P/N 15140:G

69

Downloading Program

7.1.1 Security Features

Remote site upload and download with the control panel has been carefully designed to include key security features
to ensure proper functionality. The key features are listed and explained below.

Secret Code Verification

A secret code is stored in the control panel by a Service Terminal to prevent unauthorized access. The secret code is
created at the Service Terminal by the master user and cannot be viewed or changed by anyone other than a master
user. Viewing of the secret code is prohibited at the control panel. Prior to allowing an upload or download of data,
the control panel will verify the secret code transmitted by the Service Terminal.

Time-out at Control Panel

Upon answering an incoming call on either the primary or secondary Central Station phone line, the control panel
will listen for a modem connection signal. If this signal is not received within 30 seconds, the control panel will dis­connect the call.

Callback to Service Terminal

Any time the control panel is requested to allow an upload or download, it will confirm the source of the incoming
call, hang-up and call back the calling party (Service Terminal phone number).

Panel Identification Number

The panel identification number is typically used to identify the panel to the Service Terminal when the control panel
calls the Service Terminal. If more than one call comes into the Service Terminal, the control panel ID number is
used to sort out the calling parties.

Another use of this code allows for identical secret codes to be placed into multiple control panels at one jobsite,
using the panel ID number to distinguish between the individual panels.

Error Checking

As each block of data is received by the control panel, it is checked for accuracy. If an error is detected, the block is
retransmitted until correct, up to a maximum of four times. If the Secret Code is not verified and four errors occur,
the call is disconnected and the report that the upload/download was not successful is called to the Central Station(s).

Central Station Acknowledge

There is an option, referred to as the ‘callback’ option, whereby the control panel will report to one or both Central
Stations that a request for uploading or downloading has been received prior to processing the call. If the Central
Station(s) does not acknowledge receipt of this request, uploading or downloading is prohibited. If acknowledged by
the Central Station(s), another message is transmitted, informing the Central Station(s) that:

• Downloading was successful

• Uploading was successful

• Uploading/downloading was not successful

Central Station Data Protection

Addresses '00' through '51' are assigned to the primary and secondary Central Station phone number, communication
format, account code and test time. Addresses '127' through '374' are reserved for the programmable event codes.
This block of addresses holds the entire vital Central Station information. These blocks are protected from partial
programming due to faulty phone connections, line noise and other errors. This prevents the panel from being con­fused due to a wrong phone number, account code, test time and most critical formatting errors.

70

Document #15140 Rev.G 01/02/02 P/N 15140:G

Downloading Initiated at Control Panel

7.2 Downloading Initiated at Control Panel

Before initiating the download procedure, make certain that the control panel is:

In Normal Mode

✓

Central Station communications are off or location 56 is set to '0'

✓

The communicator is in the standby state (red Line Seize LEDs are off, green Modem and Kissoff LEDs

✓

are off)

Place the control panel into Program Mode and program one or both of the Service Terminal phone numbers. It is
also advisable at this time to program the Panel Identification Number at addresses 84 - 87. This will allow the Ser­vice Terminal to easily identify incoming calls.

Exit the Program Mode and return the panel to Normal Mode. Press the MODE key followed by the 4-digit code

3696 and then the [ENTER/STORE] key.

3696 spells DOWN on a Touch-Tone

☛

The display to the far left will flash the letter 'S'. Press the digit '1' for Service Terminal phone #1 or '2' for Service
Terminal #2, followed by [ENTER/STORE]. The control panel will now call the appropriate Service Terminal
phone number and the downloading process will begin.

®

phone.

Once the called Service Terminal identifies the incoming call (control panel), the downloading process is allowed to
continue. Downloading progresses until all programmed information has been successfully loaded into the control
panel. The programmed data may consist of addresses 00-374 plus the time and date.

7.3 Downloading Initiated at a Service Terminal

Before initiating the download procedure, make certain that the control panel is:

In Normal Mode

✓

Central Station communications are off or location 56 is set to '0'

✓

The communicator is in the standby state (red Line Seize LEDs are off, green Modem and Kissoff LEDs

✓

are off)

Once the control panel accepts/answers an incoming call, the panel will:

Establish basic modem connection

1.

Verify secret code and panel identification number

2.

Verify callback vs. no callback request from the service terminal. If callback is requested, steps 4 through 9

3.

will occur. If no callback is requested, only steps 8 and 9 will occur

Identify the Service Terminal location

4.

Hang-up/disconnect call

5.

Call the Central Station(s) and transmit a request for upload/download message (if programmed to do so). If

6.

this message is accepted, the control panel will proceed to the next step

Return call to Service Terminal

7.

After security clearance, begin downloading

8.

Upon completion of download, call Central Station(s) back and report either a successful download or failed

9.

upload/download message (if programmed to do so)

Document #15140 Rev.G 01/02/02 P/N 15140:G

71

Uploading Initiated at a Service Terminal

7.4 Uploading Initiated at a Service Terminal

Items that may be uploaded from the control panel to a Service Terminal are:

• All programmed data from addresses 00-374 plus the real-time clock, time and date

• Entire Walktest data file

• Troubleshoot Mode system voltages

• Entire 32 event History file

• Current system status

Uploading is possible at any time provided the following conditions are true:

✓ The control panel must be in the Normal Mode of operation. Uploading is not possible if the panel is in

any other mode

✓ There cannot be any active communications ongoing with a Central Station receiver

✓

All active events must be successfully 'kissed-off' by the Central Station (the communicator must be in
a standby state with no new information waiting to be transmitted to a Central Station)

Once an incoming call is accepted/answered by the control panel, the panel will:

Establish basic modem connection

1.

Verify secret code and panel identification number

2.

Verify callback vs. no callback request from the service terminal. If callback is requested, steps 4 through 9

3.

will occur. If no callback is requested, only steps 8 and 9 will occur

Identify the Service Terminal location

4.

Hang-up/disconnect call

5.

Call the Central Station(s) and transmit a request for upload/download message (if programmed to do so). If

6.

this message is accepted, the control panel will proceed to the next step

Return call to Service Terminal

7.

After security clearance, begin uploading

8.

Upon completion of upload, call Central Station(s) back and report either a successful upload or failed upload/

9.

download message (if programmed to do so).

During the uploading process, the fire protection remains active

. Should a system trouble or alarm condition
occur, the control panel immediately terminates uploading and processes the trouble or alarm locally and trans­mits the information to the Central Station(s).

72

Document #15140 Rev.G 01/02/02 P/N 15140:G

Battery Calculations

Appendix A Battery Calculations

Use the Total Standby and Alarm Load Currents calculated in Table A-2 and Table A-3 for the following battery
calculation.

TAB LE A- 1:

Standby Load

Current (Amps)

Current (Amps)

Battery Calculations

[ ]

Alarm Load

[ }

Required Standby Time in Hours

X

(24 or 60 Hours)

[ ]

Required Alarm Time in Hours

X

(i.e. 5 minutes = 0.084)

[ ]

Add Standby and Alarm Load for Required Ampere Hour Battery = __________

Multiply by the Derating Factor of 1.2 X 1.2 __________

Total Ampere Hours (AH) Required = __________

Note:

7 Ampere Hour battery can be located in the backbox.

1.

12 Ampere Hour and 17 Ampere Hour batteries require the BB-17F battery box.

2.

= __________

= __________

Document #15140 Rev.G 01/02/02 P/N 15140:G

73

Battery Calculations

A.1 The Main Power Supply

The MS-5024UD provides filtered power for operating the fire alarm control panel, external devices and the standby
battery. The power for operating external devices is limited. Use Table A-2 (standby or nonalarm) and Table A-3
(alarm) to determine if external loading is within the capabilities of the power supply.

Concerning 4-wire smoke detectors: Be sure to power smoke detectors from TB4, Terminals 3 and 4.

TABLE A-2:

Filtered Load in Standby - external devices connected to TB4 only

Device Type

# of

Devices

Current
(Amps)

Total Current

(Amps)

Main Circuit Board 1 X 0.1 = 0.1

ADM-24 (1 max.) X 0.006 =

RZA-5F (1 max.) X 0 = 0

RM-5F (1 max.) X 0 = 0

CAC-5F (1 max.) X 0 = 0

2-wire Smoke Detector

Heads

[ ] X

[ ]

1

=

4-wire Smoke Detector

Heads

Power Supervision

2

Relays

Current Draw from

TB4 (nonalarm)

3

[ ] X

[ ] X 0.025 =

[ ]

1

=

=

Sum Column for Standby Load = Amps

1. Refer to the Device Compatibility Document for 2-wire smoke detector standby current.

2. Must use compatible listed power supervision relay.

3. The total standby current must include the sum of both the resettable (TB4, Terminals 3 & 4) and nonresettable (TB4,
Terminals 5 & 6) power. Caution must be taken to ensure that current drawn from these outputs during alarm does not
exceed maximum ratings specified (refer to Table A-3 )

74

Document #15140 Rev.G 01/02/02 P/N 15140:G

Battery Calculations

TAB LE A- 3:

Filtered Load in Alarm

Device Type

# of

Devices

Current

(Amps)

Main Circuit Board 1 X 0.170 =

ADM-24 (1 max.) X 0.006 =

RZA-5F (1 max.) X

RM-5F (1 max.) X

0.046

0.080

2

2

CAC-5F (1 max.) X 0 = 0

4

4-wire Smoke Detector

Heads

Power Supervision Relays

[ ] X [ ] =

3

[ ] X 0.025 =

Total C urr ent

(Amps)

1

0.170

=

=

4

Notification Appliances

Notification Appliances

Current Draw from TB4

(alarm)

Sum Column for Standby Load

1. The current shown represents one zone on the main circuit board in alarm. For all five zones in alarm, the current draw
increases to 0.36 amps.

2. The currents shown for the RZA-5F and RM-5F are for all five zones in alarm. For one zone in alarm, the RZA-5F cur­rent draw is 16 mA and the RM-5F current draw is 12 mA.

3. Must use compatible listed Power Supervision Relay.

4. Current limitations of terminals:

- TB4, Terminals 1 & 2 = 0.300 amp, filtered 24VDC +/- 5%, 120Hz ripple @ 10 mV
ripple for MS-5024UDE).

- TB4, Terminals 3 & 4 = 0.300 amp, filtered 24VDC +/- 5%, 120Hz ripple @ 10 mV
ple for MS-5024UDE)

- TB5, 2.5 amps.

- TB6, 2.5 amps.

5. Total Current draw listed above cannot exceed:

- 3.6 amps with only the standard transformer installed

- 5.6 amps with both the standard and optional transformer installed

[ ] X [ ] =

4

[ ] X [ ] =

4

5

=

=Amps

. Nonresettable power (100Hz

RMS

. Resettable power (100Hz rip-

RMS

Document #15140 Rev.G 01/02/02 P/N 15140:G

75

Programming Reference Sheets

f

f

f
f

Appendix B Programming Reference Sheets

...To enter Programming Mode, press the MODE key, the code 7764 and then the [ENTER/STORE] key...

❐00❐01❐02❐03❐04❐05❐06❐07❐08❐09❐10❐11❐12❐13❐14❐

Addresses 00 to 15 store the Primary Central Station Phone Number. Enter 'F' to represent the end of the number.

❐

Primary Central Station Communication Format: Enter '0 - F'.

16

❐17❐18❐19❐
❐21❐22❐23❐
❐

Primary Number Test Time Interval. Enter '0' for 24 hour; '1' for 12 hour; '2' for 8 hour; '3' for 6 hour.

25

Primary Central Station Account Code: Valid entries are '0 - F'.

20

Primary Central Station 24-Hour Test Time. Enter military time (i.e. 1400 for 2 PM).

24

❐26❐27❐28❐29❐30❐31❐32❐33❐34❐35❐36❐37❐38❐39❐40❐

Addresses 26 to 41 store the Secondary Central Station Phone Number. Enter 'F' to represent the end of the number.

❐

Secondary Central Station Communication Format: Enter '0 - F'.

42

❐43❐44❐45❐
❐47❐48❐49❐
❐

Secondary Number Test Time Interval. Enter '0' for 24 hour; '1' for 12 hour; '2' for 8 hour; '3' for 6 hour.

51

❐

Alarm Verification. Enter '0' for no verification; '1' for verification of all 2-wire smoke zones.

52

❐53❐54❐
❐

Slave Communicator/Fire Panel Selection. Enter '0' for fire panel only; '1' for slave communicator only; '2'

56

or fire panel/communicator operation.

55

Secondary Central Station Account Code: Valid entries are '0 - F'.

46

Secondary Central Station 24-Hour Test Time. Enter military time (i.e. 1400 for 2 PM).

50

Future use.

15

41

❐

Zone 1 Function Select. Enter '0' for 2-wire smoke detectors; '1' for pull station; '2' for normally open contact

57

devices; '3' for supervisory devices; '4' for supervisory devices (autoresettable).

❐

Zone 2 Function Select. Enter '0' for 2-wire smoke detectors; '1' for pull station; '2' for normally open contact

58

devices; '3' for supervisory devices; '4' for supervisory devices (autoresettable).

❐

Zone 3 Function Select. Enter '0' for 2-wire smoke detectors; '1' for pull station; '2' for normally open contact

59

devices; '3' for supervisory devices; '4' for supervisory devices (autoresettable); '5' for waterflow (silenceable); '6'

or waterflow (nonsilenceable).

❐

Zone 4 Function Select. Enter '0' for 2-wire smoke detectors; '1' for pull station; '2' for normally open contact

60

devices; '3' for supervisory devices; '4' for supervisory devices (autoresettable).

❐

Zone 5 Function Select. Enter '0' for 2-wire smoke detectors; '1' for pull station; '2' for normally open contact

61

devices; '3' for supervisory devices; '4' for supervisory devices (autoresettable).

❐62❐
❐

64

or 11 hours; '6' for 12 hours; '7' for 15 hours; '8' for 16 hours; '9' for 17 hours; 'A' for 18 hours; 'B' for 19 hours; 'C'
or 20 hours; 'D' for 21 hours; 'E' for 22 hours; 'F' for 23 hours.

❐

65

❐66❐67❐

Waterflow Retard timer. Enter 0 - 89 additional seconds.

63

AC Loss Delay. Enter '0' for 6 hour delay; '1' for 7 hours; '2' for 8 hours; '3' for 9 hours; '4' for 10 hours; '5'

Alarm Presignal. Enter '0' to disable alarm presignal; '1' to enable.

Alarm Presignal Delay Timer. Enter 0 - 179 additional seconds (default - 120 seconds).

68

❐

69

able); '2' for disabled.

76

Notification Appliance Circuit #1 Selection. Enter '0' for enabled (silenceable); '1' for enabled (nonsilence-

Document #15140 Rev.G 01/02/02 P/N 15140:G

Programming Reference Sheets

f

f

❐

Silence Inhibit NAC #1. Enter '0' for no silence inhibit; '1' to inhibit silencing of NAC #1 for one minute.

70

❐

Autosilence NAC #1. Enter '0' for no autosilence; '1' for 5 minutes; '2' for 10 minutes; '3' for 15 minutes; '4'

71

or 20 minutes; '5' for 25 minutes; '6' for 30 minutes.

❐

Coding NAC #1. Enter '0' for steady; '1' for March Time (120 ppm); '2' for California (10 seconds On, 5 sec-

72

onds Off); '3' for Temporal (½ second On, ½ second Off, ½ second On, ½ second Off, ½ second On, 1½ second Off).

❐

Notification Appliance Circuit #2 Selection. Enter '0' for enabled (silenceable); '1' for enabled (nonsilence-

73

able); '2' for disabled.

❐

Silence Inhibit NAC #2. Enter '0' for no silence inhibit; '1' to inhibit silencing of NAC #2 for one minute.

74

❐

Autosilence NAC #2. Enter '0' for no autosilence; '1' for 5 minutes; '2' for 10 minutes; '3' for 15 minutes; '4'

75

or 20 minutes; '5' for 25 minutes; '6' for 30 minutes.

❐

Coding NAC #2. Enter '0' for steady; '1' for March Time (120 ppm); '2' for California (10 seconds On, 5 sec-

76

onds Off); '3' for Temporal (½ second On, ½ second Off, ½ second On, ½ second Off, ½ second On, 1½ second Off)

❐

Trouble Reminder. Enter '0' to disable trouble reminder; '1' to enable.

77

❐

Annunciator/Printer Supervision. Enter '0' for annunciator/printer not present; '1' for annunciator present;

78

'2' for printer present; '3' for annunciator and printer present.

❐

Backup Reporting. Enter '0' to report to secondary phone number as backup only; '1' to report to secondary

79

phone number for all reports/messages. Does not affect upload/download messages.

❐

Touchtone/Rotary Select. Enter '0' for touchtone dialing; '1' for rotary dialing.

80

❐

Make/Break Ratio. Enter '0' for 67/33 ratio; '1' for 62/38 ratio.

81

❐

Future use.

82

❐

Future use.

83

❐84❐85❐86❐
❐88❐89❐90❐91❐92❐93❐94❐95❐96❐97❐98❐99❐

Service Terminal #1 Phone Number. Addresses 88 - 103 store the phone number of Service Terminal #1. Enter 'F' to
represent the end of the number.

❐

104❐105

❐

106

❐

107❐108❐109❐110❐111❐112❐113❐114❐115❐116❐117❐118❐119❐120❐121❐122

Service Terminal #2 Phone Number. Addresses 107 - 122 store the phone number of Service Terminal #2. Enter 'F'

to represent the end of the number.

Ring Count on Primary Phone Line. Enter number of rings prior to panel answering call.

FAX/Answer Machine, Primary Phone Line. Enter '0' for no sharing of phone line; '1' for sharing.

Panel Identification Number. Valid entries are '0 - F'.

87

100❐101❐102❐103

❐

123❐124

❐

125

❐

126

Station Phone Number on backup only; '1' for Upload/Download reports to always go to the Secondary Number.

Ring Count on Secondary Phone Line. Enter number of rings prior to panel answering call.

FAX/Answer Machine, Secondary Phone Line. Enter'0' for no sharing of phone line; '1' for sharing.

Upload/Download Backup Reporting. Enter '0' for Upload/Download reports to go to the Secondary Central

Document #15140 Rev.G 01/02/02 P/N 15140:G

77

Programming Reference Sheets

Programming Reference Sheets

❐

❐

❐

❐

❐

❐

❐

❐

❐

127

140

153

166

179

192

205

218

231

❐

❐

❐

❐

❐

❐

❐

❐

❐

128

141

154

167

180

193

206

219

232

❐

❐

❐

❐

❐

❐

❐

❐

❐

129

142

155

168

181

194

207

220

233

❐

❐

❐

❐

❐

❐

❐

❐

❐

130

143

156

169

182

195

208

221

234

❐

❐

❐

❐

❐

❐

❐

❐

❐

131

144

157

170

183

196

209

222

235

❐

❐

❐

❐

❐

❐

❐

❐

❐

132

145

158

171

184

197

210

223

236

❐

❐

❐

❐

❐

❐

❐

❐

❐

133

146

159

172

185

198

211

224

237

❐

❐

❐

❐

❐

❐

❐

❐

❐

134

147

160

173

186

199

212

225

238

❐

❐

❐

❐

❐

❐

❐

❐

❐

135

148

161

174

187

200

213

226

239

❐

❐

❐

❐

❐

❐

❐

❐

❐

136

149

162

175

188

201

214

227

240

❐

❐

❐

❐

❐

❐

❐

❐

❐

137

150

163

176

189

202

215

228

241

❐

❐

❐

❐

❐

❐

❐

❐

❐

138

151

164

177

190

203

216

229

242

❐

❐

❐

❐

❐

❐

❐

❐

❐

139

152

165

178

191

204

217

230

243

❐

❐

❐

❐

❐

❐

❐

❐

❐

244

257

270

283

296

309

322

335

348

❐

❐

❐

❐

❐

❐

❐

❐

❐

245

258

271

284

297

310

323

336

349

❐

❐

❐

❐

❐

❐

❐

❐

❐

246

259

272

285

298

311

324

337

350

❐

❐

❐

❐

❐

❐

❐

❐

❐

247

260

273

286

299

312

325

338

351

❐

❐

❐

❐

❐

❐

❐

❐

❐

248

261

274

287

300

313

326

339

352

❐

❐

❐

❐

❐

❐

❐

❐

❐

249

262

275

288

301

314

327

340

353

❐

❐

❐

❐

❐

❐

❐

❐

❐

250

263

276

289

302

315

328

341

354

❐

❐

❐

❐

❐

❐

❐

❐

❐

251

264

277

290

303

316

329

342

355

❐

❐

❐

❐

❐

❐

❐

❐

❐

252

265

278

291

304

317

330

343

356

❐

❐

❐

❐

❐

❐

❐

❐

❐

253

266

279

292

305

318

331

344

357

❐

❐

❐

❐

❐

❐

❐

❐

❐

254

267

280

293

306

319

332

345

358

❐

❐

❐

❐

❐

❐

❐

❐

❐

255

268

281

294

307

320

333

346

359

❐

❐

❐

❐

❐

❐

❐

❐

❐

256

269

282

295

308

321

334

347

360

78

❐

❐

361

374

❐

362

❐

❐

363

Document #15140 Rev.G 01/02/02 P/N 15140:G

364

❐

365

❐

366

❐

367

❐

368

❐

369

❐

370

❐

371

❐

372

❐

373

Programming Reference Sheets

Programming Reference Sheets - Factory Default Settings

...To enter Programming Mode, press the MODE key, the code 7764 and then the [ENTER/STORE] key...

FFFFFFFFFFFFFFFF

❐00❐01❐02❐03❐04❐05❐06❐07❐08❐09❐10❐11❐12❐13❐14❐

Addresses 00 to 15 store the Primary Central Station Phone Number. Enter 'F' to represent the end of the number.

E

❐

Primary Central Station Communication Format: 'E' for Ademco Contact ID.

16

0000

❐17❐18❐19❐

2345

❐21❐22❐23❐

0

❐

Primary Number Test Time Interval. '0' for 24 hours.

25

FFFFFFFFFFFFFFFF

❐26❐27❐28❐29❐30❐31❐32❐33❐34❐35❐36❐37❐38❐39❐40❐

Addresses 26 to 41 store the Secondary Central Station Phone Number. Enter 'F' to represent the end of the number.

E

❐

Secondary Central Station Communication Format: ‘E' for Ademco Contact ID.

42

0000

❐43❐44❐45❐

0000

❐47❐48❐49❐

0

❐

Secondary Number Test Time Interval. 0' for 24 hours.

51

0

❐

Alarm Verification. '0' for no verification.

52

000

❐53❐54❐

0

❐

Slave Communicator/Fire Panel Selection. 0' for fire panel only operation.

56

0

❐

Zone 1 Function Select. '0' for 2-wire smoke detectors.

57

0

❐

Zone 2 Function Select. '0' for 2-wire smoke detectors.

58

0

❐

Zone 3 Function Select. '0' for 2-wire smoke detectors.

59

0

❐

Zone 4 Function Select. '0' for 2-wire smoke detectors.

60

0

❐

Zone 5 Function Select. '0' for 2-wire smoke detectors.

61

00

❐62❐

0

❐

AC Loss Delay. '0' for 6 hour delay.

64

0

❐

Alarm Presignal. '0' for no alarm presignal.

65

120

❐66❐67❐

0

❐

Notification Appliance Circuit #1 Selection. '0' for enabled (silenceable).

69

0

❐

Silence Inhibit NAC #1. '0' for no silence inhibit.

70

0

❐

Autosilence NAC #1. '0' for no autosilence.

71

0

❐

Coding NAC #1. '0' for steady no coding.

72

0

❐

Notification Appliance Circuit #2 Selection. '0' for enabled (silenceable).

73

55

Waterflow Retard timer. '00' for no delay.

63

68

Primary Central Station Account Code.

20

Primary Central Station 24-Hour Test Time. 2345 = 11:45 PM.

24

Secondary Central Station Account Code.

46

Secondary Central Station 24-Hour Test Time. 0000 = 12:00 midnight.

50

Future use.

Alarm Presignal Delay Timer. 120 second alarm presignal delay.

15

41

Document #15140 Rev.G 01/02/02 P/N 15140:G

79

Programming Reference Sheets

0

❐

Silence Inhibit NAC #2. '0' for no silence inhibit.

74

0

❐

Autosilence NAC #2. '0' for no autosilence.

75

0

❐

Coding NAC #2. '0' for steady no coding.

76

0

❐

Trouble Reminder. '0' for no trouble reminder.

77

0

❐

Annunciator/Printer Supervision. '0' for annunciator/printer not present.

78

0

❐

Backup Reporting. '0' to report to secondary phone number as backup only.

79

0

❐

Touchtone/Rotary Select. '0' for touchtone dialing.

80

0

❐

Make/Break Ratio. '0' for 67/33 ratio.

81

0

❐

Future use. Leave default of '0'.

82

0

❐

Future use. Leave default of '0'.

83

0000

❐84❐85❐86❐

Panel Identification Number. Default is '0000'.

87

FFFFFF FFFFFFF FFF

❐88❐89❐90❐91❐92❐93❐94❐95❐96❐97❐98❐99❐

Service Terminal #1 Phone Number. Enter 'F' to represent the end of the number.

03

❐

104❐105

0

❐

106

FFFFFF FFFFFFF FFF

❐

107❐108❐109❐110❐111❐112❐113❐114❐115❐116❐117❐118❐119❐120❐121❐122

Service Terminal #2 Phone Number. Enter 'F' to represent the end of the number.

03

❐

123❐124

0

❐

125

0

❐

126

tion Phone Number on backup only.

Ring Count on Primary Phone Line. Default is '03' for do not answer until 3 rings are detected.

FAX/Answer Machine, Primary Phone Line. '0' for no sharing of phone line.

Ring Count on Secondary Phone Line. Default is '03' for do not answer until 3 rings are detected.

FAX/Answer Machine, Secondary Phone Line. '0' for no sharing of phone line.

Upload/Download Backup Reporting. '0' for Upload/Download reports to go to the Secondary Central Sta-

100❐101❐102❐103

80

Document #15140 Rev.G 01/02/02 P/N 15140:G

Programming Reference Sheets

Programming Reference Sheets Factory Default

1111111111111

❐

❐

❐

❐

❐

❐

❐

❐

127

1157057057057

❐

140

0570604301380

❐

153

3803803803803

❐

166

1030231135135

❐

179

2321322354354

❐

192

3303086026084

❐

205

128

141

154

167

180

193

206

❐

❐

❐

❐

❐

❐

❐

129

142

155

168

181

194

207

❐

❐

❐

❐

❐

❐

❐

130

143

156

169

182

195

208

❐

❐

❐

❐

❐

❐

❐

131

144

157

170

183

196

209

❐

❐

❐

❐

❐

❐

❐

132

145

158

171

184

197

210

❐

❐

❐

❐

❐

❐

❐

133

146

159

172

185

198

211

❐

❐

❐

❐

❐

❐

❐

134

147

160

173

186

199

212

❐

❐

❐

❐

❐

❐

❐

135

148

161

174

187

200

213

❐

❐

❐

❐

❐

❐

❐

136

149

162

175

188

201

214

❐

❐

❐

❐

❐

❐

❐

137

150

163

176

189

202

215

❐

❐

❐

❐

❐

❐

❐

138

151

164

177

190

203

216

❐

❐

❐

❐

❐

❐

❐

139

152

165

178

191

204

217

11416412413

❐

218

❐

219

❐

220

❐

221

❐

222

❐

223

❐

224

❐

225

❐

226

❐

227

❐

228

Document #15140 Rev.G 01/02/02 P/N 15140:G

81

Operation and Function Modes

Appendix C Operation and Function Modes

C.1 Operation Modes

TABLE C-1:

Operation Modes

CODE ACTIVITY NOTES

6676 (NORM) Returns to normal operation Fire protection is on

7764 (PROG) Enters Program Mode

9255 (WALK) Enters Walktest Mode

4478 (HIST) View History File

8768 (TROU)

Activates internal system voltmeter for trou­bleshooting and diagnosing problems

Sends status, history file, walktest file, trou-

7746 (PRIN)

bleshoot voltages and entire programming
selections to printer

5267 (LAMP)

3696 (DOWN)

Turns on all LEDs on the main circuit board
and all system annunciators for five seconds

Allows for downloading the entire program
file to the panel

4 levels of programming may be entered.
Fire protection is off

May select audible walktest function. Fire
protection is off

Use display or printer to view History File.
Fire protection is off

Fire protection is off while voltmeter function
is enabled

Fire protection is off. Requires PRT-24
option module

Fire protection is on

Must have service terminal ready. Fire pro­tection remains on

C.2 Function Modes

TABLE C-2:

CODE ACTIVITY NOTES

3472 (DISA) Allows disabling of any input zone

3622 (ENAB)

3745 (DRIL)

3337 (DEFP)

Function Modes

Allows enabling (return to normal) of any
zone

Performs drill function by turning on all
NAC outputs

Reprograms all entries for programming
back to the original factory settings

May only disable one zone at a time. Places
system into trouble

May only enable one zone at a time

Transmission of drill function to Central Sta­tion is defaulted to ON

Entry of code must be performed two times in
rapid succession as a safety feature. Use
caution when using this feature

82

Document #15140 Rev.G 01/02/02 P/N 15140:G

Ademco Contact ID Format Event Code Descriptions

Appendix D Ademco Contact ID Format Event

Code Descriptions

This appendix describes the various Event Codes and their messages which are available for the Ademco Contact ID
Format.

The reporting structure for the Ademco Contact ID Format is as follows:

SSS 18 QXYZ GG CCC

where

SSSS = Four digit Subscriber ID Account Code (addresses 17 - 20 and 43 - 46)

18 = Identifies transmission as Contact ID to the receiver at the Central Station

Q = Event Qualifier where 1 = New Event and 3 = New Restore

XYZ = Event code (shown in Table 3-3 on page 38 and Table 3-6 on page 43)

GG = Group number

CCC = Zone number

Notes:

GG Group Number is fixed at '00' and cannot be changed.

1.

CCC Zone Number is transmitted as '001' for zone one up to '005' for zone five.

2.

Ademco Contact ID Reporting Structure

A typical printout from a Central Station receiver (such as the Ademco 685) of alarm and trouble reports in the
Ademco Contact ID Reporting Structure follows:

Time Date Rcvr/Line ID SSSS QXYZ GG CCCC

11:28 03/25 11 7777 E110 00 C001 - general fire alarm on zone one

11:28 03/25 11 7777 E111 00 C002 - smoke detector alarm on zone two

11:28 03/25 11 7777 E380 00 C003 - fault on zone three

11:28 03/25 11 7777 E570 00 C004 - Zone four disabled

11:28 03/25 11 7777 R110 00 C001 - Zone one alarm restored

11:28 03/25 11 7777 R111 00 C002 - smoke detector zone two restored

11:28 03/25 11 7777 R380 00 C003 - zone three fault restored

11:28 03/25 11 7777 R570 00 C004 - zone four reenabled

11:28 03/25 11 7777 E158 00 C005 - high temperature, zone five

11:28 03/25 11 7777 E151 00 C003 - gas detected, zone three

Notes:

18

, which is used in the reporting structure to identify the transmission as Contact ID, is not printed out in the

1.

alarm and trouble report.

Q

, which is the Event Qualifier for the reporting structure, is printed out in the report as an E for New Event or

2.

R

for New Restore.

Document #15140 Rev.G 01/02/02 P/N 15140:G

83

Ademco Contact ID Format Event Code Descriptions

EVENT CODE CLASSIFICATIONS

1 0 0

ALARMS

Medical
Fire
Panic
Burglary
General
24 Hour

2 00

SUPERVISORY

Fire

3 00

TROUBLES

System
Sounder/Relay
System Peripheral
Communication
Protective Loop
Sensor

400

OPEN/CLOSE

REMOTE ACCESS

Open/Close
Remote Access
Access Control

5 00

DISABLES/

BYPASSES

System
Sounder/Relay
System Peripheral
Communication

EVENT MESSAGE

Medical Alarms - 100
100 Medical EMERG - Personal Emergency - #
101 Pendant transmitter EMERG - Personal Emergency - #
102 Fail to report in EMERG - Fail to Check-in - #

Fire Alarms - 110
110 Fire Alarm FIRE - Fire Alarm - #
111 Smoke FIRE - Smoke Detector - #
112 Combustion FIRE - Combustion - #
113 Waterflow FIRE - Waterflow - #
114 Heat FIRE - Heat Sensor - #
115 Pull station FIRE - Pull Station - #
116 Duct FIRE - Duct Sensor - #
117 Flame FIRE - Flame Sensor - #
118 Near Alarm FIRE - Near Alarm - #

600
TEST/
MISC.

Te st

Panic Alarms - 120
120 Panic Alarm PANIC - Panic - #
121 Duress PANIC - Duress
122 Silent PANIC - Silent Panic - #
123 Audible PANIC - Audible Panic - #

Burglar Alarms - 130
130 Burglary BURG - Burglary - #
131 Perimeter BURG - Perimeter - #
132 Interior BURG - Interior - #
133 24-Hour BURG - 24-Hour - #
134 Entry/Exit BURG - Entry/Exit - #
135 Day/Night BURG - Day/Night - #
136 Outdoor BURG - Outdoor - #
137 Tamper BURG - Tamper - #
138 Near Alarm BURG - Near Alarm - #

General Alarms - 140
140 General Alarm ALARM - General Alarm - #
141 Polling loop open ALARM - Polling Loop Open - #
142 Polling loop short ALARM - Polling Loop Short - #
143 Expansion module failure ALARM - Exp. Module Fail - #
144 Sensor tamper ALARM - Sensor Tamper - #
145 Expansion module tamper ALARM - Exp. Module Tamper - #

84

Document #15140 Rev.G 01/02/02 P/N 15140:G

Ademco Contact ID Format Event Code Descriptions

EVENT MESSAGE

24 Hour Non-Burglary - 150 and 160
150 24-Hour Non-Burg ALARM - 24-Hr. Non-Burg - #
151 Gas detected ALARM - Gas Detected - #
152 Refrigeration ALARM - Refrigeration - #
153 Loss of heat ALARM - Heating System - #
154 Water leakage ALARM - Water Leakage - #
155 Foil break ALARM - Foil Break - #
156 Day trouble ALARM - Day Zone - #
157 Low bottled gas level ALARM - Low Gas Level - #
158 High temp ALARM - High Temperature - #
159 Low temp ALARM - Low Temperature - #
161 Loss of air flow ALARM - Air Flow - #

Fire Supervisory - 200 and 210
200 Fire supervisory SUPER. - Fire Supervisory - #
201 Low water pressure SUPER. - Low Water Pressure - #
202 Lox CO2 SUPER. - Low CO2
203 Gate valve sensor SUPER. - Gate Valve - #
204 Low water level SUPER. - Low Water Level - #
205 Pump activated SUPER. - Pump Activation - #
206 Pump failure SUPER. - Pump Failure - #

System Troubles - 300 and 310
300 System trouble TROUBLE - System Trouble
301 AC loss TROUBLE - AC Power
302 Low system battery TROUBLE - System Low Battery
303 RAM checksum bad TROUBLE - Bad RAM Checksum (Restore not applicable)
304 ROM checksum bad TROUBLE - Bad ROM Checksum (Restore not applicable)
305 System reset TROUBLE - System Reset (Restore not applicable)
306 Panel program changed TROUBLE - Programming Changed (Restore not applicable)
307 Self-test failure TROUBLE - Self Test Failure
308 System shutdown TROUBLE - System Shutdown
309 Battery test failure TROUBLE - Battery Test Failure
310 Ground fault TROUBLE - Ground Fault - #
311 No battery TROUBLE - No Battery

Sounder/Relay Troubles - 320
320 Sounder/Relay TROUBLE - Sounder Relay - #
321 Bell 1 TROUBLE - Bell/Siren #1
322 Bell 2 TROUBLE - Bell/Siren #2
323 Alarm relay TROUBLE - Alarm Relay
324 Trouble relay TROUBLE - Trouble Relay
325 Reversing TROUBLE - Reversing Relay
326 Bell 3 TROUBLE - Bell/Siren #3
327 Bell 4 TROUBLE - Bell/Siren #4

System Peripheral Troubles - 330 and 340
330 System peripheral TROUBLE - Sys. Peripheral - #
331 Polling loop open TROUBLE - Polling Loop Open
332 Polling loop short TROUBLE - Polling Loop Short
333 Expansion module failure TROUBLE - Exp. Module Fail - #
334 Repeater failure TROUBLE - Repeater Failure - #
335 Local printer paper out TROUBLE - Printer Paper Out
336 Local printer failure TROUBLE - Local Printer

Document #15140 Rev.G 01/02/02 P/N 15140:G

85

Ademco Contact ID Format Event Code Descriptions

EVENT MESSAGE

Communication Troubles - 350 and 360
350 Communication TROUBLE - Communication Trouble
351 Telco 1 fault TROUBLE - Phone Line #1
352 Telco 2 fault TROUBLE - Phone Line #2
353 Long range radio xmitter fault TROUBLE - Radio Transmitter
354 Fail to communicate TROUBLE - Fail to Communicate
355 Loss of radio supervision TROUBLE - Radio Supervision
356 Loss of central polling TROUBLE - Central Radio Polling

Protection Loop Troubles - 370
370 Protection loop TROUBLE - Protection Loop - #
371 Protection loop open TROUBLE - Protection Loop Open - #
372 Protection loop short TROUBLE - Protection Loop Short - #
373 Fire Trouble TROUBLE - Fire Loop - #

Sensor Troubles - 380
380 Sensor trouble TROUBLE - Sensor Trouble - #
381 Loss of supervision - RF TROUBLE - RF Sensor Supervision - #
382 Loss of supervision - RPM TROUBLE - RPM Sensor Supervision - #
383 Sensor tamper TROUBLE - Sensor Tamper - #
384 RF transmitter low battery TROUBLE - RF Sensor Batt. - #

Open/Close - 400
400 Open/Close OPENING CLOSING
401 Open/Close by user OPENING - User # CLOSING - User #
402 Group Open/Close OPENING - Group User # CLOSING - Group User #
403 Automatic Open/Close OPENING - Automatic CLOSING - Automatic
404 Late Open/Close OPENING - Late CLOSING - Late
405 Deferred Open/Close Opening not used Closing not used
406 Cancel OPENING - Cancel Closing not used
407 Remote arm/disarm OPENING - Remote CLOSING - Remote
408 Quick arm Opening not applicable CLOSING - Quick arm
409 Keyswitch Open/Close OPENING - Keyswitch CLOSING - Keyswitch

Remote Access - 410
411 Callback request made REMOTE - Callback Requested Restore not applicable
412 Success - download/access REMOTE - Successful Access Restore not applicable
413 Unsuccessful access REMOTE - Unsuccessful Access Restore not applicable
414 System shutdown REMOTE - System Shutdown
415 Dialer shutdown REMOTE - Dialer Shutdown
416 Success - upload/access REMOTE - Successful Access Restore not applicable

Access Control - 420
421 Access denied ACCESS - Access Denied - User # Restore not used
422 Access report by user ACCESS - Access Gained - User # Restore not used

System Disables - 500 and 510

86

Document #15140 Rev.G 01/02/02 P/N 15140:G

Ademco Contact ID Format Event Code Descriptions

EVENT MESSAGE

Sounder/Relay Disables - 520
520 Sounder/Relay disable DISABLE - Sounder/Relay - #
521 Bell 1 disable DISABLE - Bell/Siren - #1
522 Bell 2 disable DISABLE - Bell/Siren - #2
523 Alarm relay disable DISABLE - Alarm Relay
524 Trouble relay disable DISABLE - Trouble Relay
525 Reversing relay disable DISABLE - Reversing Relay
526 Bell 3 disable DISABLE - Bell/Siren - #3
527 Bell 4 disable DISABLE - Bell/Siren - #4

System Peripheral Disables - 530 and 540

Communication Disables - 550 and 560
551 Dialer disabled DISABLE - Dialer Disable
552 Radio transmitter disabled DISABLE - Radio Disable

Bypasses - 570
570 Zone bypass BYPASS - Zone Bypass - #
571 Fire bypass BYPASS - Fire Bypass - #
572 24-Hour zone bypass BYPASS - 24-Hour Bypass - #
573 Burglar bypass BYPASS - Burg. Bypass - #
574 Group bypass BYPASS - Group Bypass - #

Test Misc. - 600
601 Manual trigger test TEST - Manually Triggered Restore not applicable
602 Periodic test report TEST - Periodic Restore not applicable
603 Periodic RF transmission TEST - Periodic Radio Restore not applicable
604 Fire test TEST - Fire Test Restore not used
605 Status report to follow STATUS - Status Follows Restore not applicable
606 Listen-in to follow LISTEN - Listen-in Active Restore not applicable
607 Walk test mode TEST - Walk Test Mode
608 System abnormal test TEST - System Abnormal Test

Document #15140 Rev.G 01/02/02 P/N 15140:G

87

Notes

88

Document #15140 Rev.G 01/02/02 P/N 15140:G

Index

Numerics

1st EVENT 13, 51

A

AC Line Voltage 65
AC Loss Reporting Delay 46
AC Power 16
AC Power LED 13, 52
Ademco Contact ID format 83
Ademco Express 14
ADM-24 29
ADM-24 Annunciator Driver

Module 15, 28
Alarm LED 13, 52
Alarm Presignal 46
Alarm Presignal Delay Timer 46
Alarm Response 53
Alarm Restoral 54
Alarm Verification 44
Alarm verification 10
Annunciator/Printer Supervision 47
Autosilence 10
Autosilence Notification Appliance

Circuit #1 46
Autosilence Notification Appliance

Circuit #2 46
Auxiliary Output 17
Auxiliary Power 24

B

Backbox 19
backbox

see also cabinet 14
Backup Reporting 47
battery 15, 16

Charger Capacity 16

Charging Circuit 16
battery box 15, 16, 21
Battery Calculations 73
Battery Charger 13
Battery Voltage 65
BB-17F 16

see also battery box 15

C

cabinet 14
Cabinet Dimensions 20
CAC-5F Class A Converter

Module 10, 15, 32
Callback 70
Central Station 10, 70
Central Station Communications 57
Circuit

Input 13
Output 13

circuit

Input 23
output 24

Coding Notification Appliance Circuit

#1 46
Coding Notification Appliance Circuit

#2 47
Communication Failure 17
communication format 14
Controls 13

D

Default Programming 49

Digital Communicator 14, 18, 27
digital communicator 10
Display 51

see also Indicators 13
Downloading 69, 71
DP-5024UD 14

see also Dress Panel 11
Dress Panel 11, 16

E

Earth Ground 22
End Programming 49
ENTER/STORE 13, 51
Error Checking 70
event code classification 84

F

FAX/Answer Machine, Primary Phone

Line 48

FAX/Answer Machine, Secondary

Phone Line 48
Fire Drill 56
Fire Panel 10
Format Selection Address 58
Formats 38, 43
Form-C 25

see also relay 17
four-wire smoke detector 10
Four-Wire Smoke Detector Power 17

Current 17
Function Modes 82
Function Selection 45

H

History file 10
History Mode 50, 63

I

IDC

current 23

see also Initiating Device Circuit 23
Indicators 13
Initiating Device Circuit 16

Alarm Current 16

End-of-Line Resistor 16

Maximum Loop Resistance 16

Normal Operating Voltage 16

Short Circuit Current 16

Standby Current 16
Installation 19

K

Keypad 34
Kissoff 10
Kissoff LED 13, 52

L

Lamp Test 66
Line Seizure 14

M

Main Circuit Board 9, 14
Make/Break Ratio 47
MODE 13, 51
Modem LED 13, 52
Mounting 19
MS-5024UD 10

N

NAC 24, 66

current/circuit 17
End-of-Line Resistor 17
Maximum Current 17
Operating Voltage 17
see also Notification Appliance

Circuit 10

Nonresettable Filtered 24V Power 17

Current 17
Nonresettable Power 13
Normal Mode 50
Notification Appliance Circuit 10, 12,

14, 17, 24

Notification Appliance Circuit #1

Enable 46

Notification Appliance Circuit #2

Enable 46

O

Off Normal Reporting 55
Operating Instructions 50
Operation 53
Operation Modes 82

P

Panel Identification Number 47, 70
Piezo

see also Sounder 13
PK-5024UD 10, 16
Power 22
Primary Central Station Number 24

Hour Test Time 39

Primary Central Station Number 24/12/

8/6 Hour Test Time
Interval 39

Primary Central Station Number

Account Code 39

Primary Central Station Number

Communication Format 35

Primary Central Station Phone

Number 34
Primary Line Active LED 52
Primary Phone Line 14
Primary Phone Line Active LED 13
primary phone number 33
Primary Power

see also AC Power 22
Primary Telephone Line 13
Print Mode 50, 66
Printer Configuration 30
Printer Port 13
Product Description 10
Product Features 10
Program Mode 33, 50
Programmable Zone ID 10
programmer 33
programmer, built-in 10
Programming 76
Programming Event Codes 48
Programming Instructions 33
Programming Options 34
PRT-24

Installation 30
PRT-24 Printer Interface Modul 16
PRT-24 Printer Interface Module 11,

30

pull station 10, 23

Document #15140 Rev.G 01/02/02 P/N 15140:G 89

R

Real-Time Clock and Calendar 48
Real-Time clock and calendar 10
Receivers 61
Relay 14
relay 10, 11, 12, 17, 25

contact rating 14, 17, 25
driver 14, 17, 25

REN

see also Ringer Equivalence

Number 18
RESET 13, 50
Resettable Power 13, 66
Ring Count on Primary Phone Line 47
Ring Count on Secondary Phone

Line 48
Ringer Equivalence Number 18
RM-5F Five-Zone Relay Module 15,

31
RM-5F Relay Module 10
RZA-5F 29
RZA-5F Remote Annunciator 15, 28

S

Secondary Central Station Number 24

Hour Test Time 44
Secondary Central Station Number 24/

12/8/6 Hour Test Time

Interval 44
Secondary Central Station Number

Account Code 44
Secondary Central Station Number

Communication Format 40
Secondary Central Station Phone

Number 39
Secondary Line Active LED 52
Secondary Phone Line 14
Secondary Phone Line Active LED 13
secondary phone number 33
Secondary Power

see also battery 22
Secondary Telephone Line 13
Secret Code 70
Security Features 70
Service Terminal 10
Service Terminal Number 1 Phone

Number 47

Service Terminal Number 2 Phone

Number 48
Servicing 62
SILENCE 13, 51
Silence inhibit 10
Silence Inhibit Notification Appliance

Circuit #1 46
Silence Inhibit Notification Appliance

Circuit #2 46
Silence LED 13, 52
Slave Communicator 10
slave communicator 10, 67
Slave Communicator/Fire Panel

Selection 44
Sounder 13
sounder 15
Specifications 16
Style B 10, 13, 23, 32
Style D 10, 13, 23, 32
Style Y 10, 14
Style Z 10, 14
Supervisory Condition Response 54

Supervisory LED 13, 52
Supervisory Restoral Response 54
Switch Functions 34

T

Telephone Circuit 24
Telephone Circuitry 18
Telephone Company

Rights and Warnings 18
telephone line 27
Telephone Lines 65
Time-out 70
Tone Burst 14
Touchtone 14
Touchtone/Rotary Select 47
transformer 12, 15
Transmittal Priorities 60
Trouble Condition Response 55
Trouble Condition Restoral 55
Trouble LED 13, 52
Trouble Reminder 47
Trouble reminder 10
Troubleshoot Mode 50, 64
two-wire smoke detector 10, 23

U

UL Power-limited Wiring

Requirements 26
Upload/Download 69
Upload/Download Reports 48
Uploading 72

V

Vo l t a g e s 6 4
voltmeter, built-in 10

W

Walktest Mode 50, 62
waterflow 23
waterflow device 10
Waterflow Retard Timer 45

X

XRM-24

see also transformer 15

Z

Zone Disable/Enable 56
Zone Voltages 64

90

Document #15140 Rev.G 01/02/02 P/N 15140:G

Limited Warranty

The manufacturer warrants its products to be free from defects in materials and workmanship
for eighteen (18) months from the date of manufacture, under normal use and service. Products
are date-stamped at time of manufacture. The sole and exclusive obligation of the manufacturer
is to repair or replace, at its option, free of charge for parts and labor, any part which is
defective in materials or workmanship under normal use and service. For products not under
the manufacturer's date-stamp control, the warranty is eighteen (18) months from date of
original purchase by the manufacturer's distributor unless the installation instructions or catalog
sets forth a shorter period, in which case the shorter period shall apply. This warranty is void
if the product is altered, repaired, or serviced by anyone other than the manufacturer or its
authorized distributors, or if there is a failure to maintain the products and systems in which
they operate in a proper and workable manner. In case of defect, secure a Return Material
Authorization form from our customer service department. Return product, transportation
prepaid, to the manufacturer.

This writing constitutes the only warranty made by this manufacturer with respect to its
products. The manufacturer does not represent that its products will prevent any loss by fire
or otherwise, or that its products will in all cases provide the protection for which they are
installed or intended. Buyer acknowledges that the manufacturer is not an insurer and assumes
no risk for loss or damages or the cost of any inconvenience, transportation, damage, misuse,
abuse, accident, or similar incident.

THE MANUFACTURER GIVES NO WARRANTY, EXPRESSED OR IMPLIED, OF
MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR OTHERWISE
WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. UNDER
NO CIRCUMSTANCES SHALL THE MANUFACTURER BE LIABLE FOR ANY LOSS
OF OR DAMAGE TO PROPERTY, DIRECT, INCIDENTAL, OR CONSEQUENTIAL,
ARISING OUT OF THE USE OF, OR INABILITY TO USE THE MANUFACTURER'S
PRODUCTS. FURTHERMORE, THE MANUFACTURER SHALL NOT BE LIABLE FOR
ANY PERSONAL INJURY OR DEATH WHICH MAY ARISE IN THE COURSE OF, OR
AS A RESULT OF, PERSONAL, COMMERCIAL, OR INDUSTRIAL USE OF ITS
PRODUCTS.

This warranty replaces all previous warranties and is the only warranty made by the
manufacturer. No increase or alteration, written or verbal, of the obligation of this warranty
is authorized.

LimWarLg.p65 01/10/2000

World Headquarters

One Fire-Lite Place, Northford, CT 06472-1653 USA

203-484-7161 • Fax [phone]

www.firelite.com