REVISIONE N°05/001
ING. O. FIORENTINI S.p.A.
INDUSTRIAL CLEANING MACHINES
0
OPERATOR MANUAL
AND PARTS LIST
CARPET SWEEPER GENIUS-14 220 Volt
ENGLISH
USE AND MAINTENANCE MANUAL
REVISIONE N°05/001
ING. O. FIORENTINI S.p.A.
INDUSTRIAL CLEANING MACHINES
1
INDEX
page
GENERAL SAFETY INSTRUCTIONS 2
ASSEMBLY INSTRUCTIONS 4
MAINTENANCE 6
TECHNICAL DATA 6
TABLE 1 7
TABLE 2 9
TABLE 3 11
ACCESSORIES 13
REVISIONE N°05/001
ING. O. FIORENTINI S.p.A.
INDUSTRIAL CLEANING MACHINES
2
These operating instruction provide you with all information necessary for correct, safe and prescribed usage and
maintenance of the carpet sweeper (all the models). They must be kept where they are accessible to the user at all times.
PRESCRIBED USAGE
This machine is designed for the professional cleaning according to these operating instructions.
Any other usage, in particular, for the removal of types of dust which may be dangerous to health, is prohibited.
GENERAL SAFETY INSTRUCTIONS
This machine is designed and constructed according to the present state of the art and recognized technical safety
standards. It is fitted with protective devices, following safety European standard rules. Dangers can occur in spite of this,
in particular in the case of non correct use or non-compliance with the specifications and information in the operating
instructions.
All our equipment are covered by international assurances against risks.
1) SOURCES OF DANGER
- Electrical voltage / Electric current
- Warning: Danger
Contact with voltage or current carrying parts carries the risk of electric shock which can result in serious injury or even
death. Never touch damaged cables. Always switch off and disconnect the power supply before carrying out any work on
the machine. Replace faulty cables immediately.
2) IMPROPER USAGE
Any usage of the machine for a purpose not covered under the “Prescribed usage” or contractually agreed purpose is not
permissible. The use of the machine in an unserviceable condition or not in compliance with the following prescription is
prohibited:
- Protective devices must not be removed or bypassed.
- Conversions and modification to the machine are not permitted.
- Defective supply cables are only to be replaced by original FIORENTINI cables.
- Coupling elements between mains supply or detachable extension cables must be at least splashproof.
- The machine is to be fitted with a type H circuit breaker for rated current of 10 A .
3) ORGANISATIONAL POINTS
It is the responsibility of the operator to ensure that:
- The machine is used only by personnel who have been instructed in its handling and authorized to use it.
- The recognized occupational safety regulations are observed.
- Any further national or internal company regulations are observed.
- All users are acquainted with the safety regulations and trained in the use of the specific machine.
- All users have read and understood the operating instructions.
- Responsibilities for the operation, maintenance and repair of the machine are clearly assigned and observed.
- Faults and damage are immediately notified to the Service Agent of FIORENTINI.
4) IN THE CASE OF AN EMERGENCY
- Pull out the mains connector plug.
- Immediately apply recognized first-aid measures.
After incidents, do not resume operation with the machine until it has been inspected by FIORENTINI authorized
technical.
5) OPERATING FOR THE FIRST TIME
Delivery, instruction on safety rules, handling and maintenance as well as operation for the first time must be carried
following the specification of this instruction book. The operator is responsible for instructing the users.
FURTHER SAFETY INSTRUCTIONS CONCERNING OPERATING AND MAINTENANCE ARE DETAILED
IN THE RELEVANT SECTIONS AND MUST BE COMPLIED WITH!
REVISIONE N°05/001
ING. O. FIORENTINI S.p.A.
INDUSTRIAL CLEANING MACHINES
3
IMPORTANT NOTES
BEFORE STARTING TO USE THE CLEANER PLEASE OBSERVE THE FOLLOWING POINTS:
- If you should discover any damage when unpacking the cleaner please inform your sale agency.
- The supply voltage must be the same as that shown on the nameplate.
ELECTRICAL CONNECTION AND SUPPLY
WARNING: - This appliance must be earthed!
- Check that the supply voltage details given on the rating plate are in accordance with your electricity supply.
CAUTION!
- The cleaner should never be used for picking up hot ashes, explosive fluids or undiluted acids or solvents. These
include petrol, paint thinner and heating oil, all of which can generate explosive mixtures or vapors when swirled
together with the suction air. Acetone, undiluted under acids and solvents would attack the materials from which
the machine is made.
WARNING NOTE
- For cleaning or servicing the cleaner or when replacing parts, the motor should be switched off and the
connecting plug be withdrawn from the socket.
- Care should be taken to ensure that the connecting cable is not damage by being driven over, crushed, strained,
etc.
- The connecting cable should be regularly checked for any signs of damage or ageing.
- The machine must not be used if the connecting cable is not in a proper condition.
- For suction of dry dust, check that the filter are in the carpet sweeper.
- Do not clean the vacuum with a water pipe to avoid that water get through the vacuum head.
GOODS TO BE RETURNED
In case of goods to be returned for warranty replacement, it is necessary to have a written acceptance from
FIORENTINI technical department before sending them.
All defective parts must be carefully packed in order to avoid further damages during transport.
Goods must be shipped ex-warehouse and followed by :
• serial number of the equipment where they were installed on;
• item code of the defective part;
• detailed description of the defect and of the condictions where it happened.
In case of defective electric or electronic goods,
please return them separately from other materials,
in order to help us in dividing dangerous wastegoods
and recicle the (RAEE) as DER 2002/96/CEE LOW.
REVISIONE N°05/001
ING. O. FIORENTINI S.p.A.
INDUSTRIAL CLEANING MACHINES
4
ASSEMBLY INSTRUCTIONS
CONNECTING OF THE CARPET SWEEPER TO THE BRUSH HEAD
Insert the upper part of the carpet sweeper into the brush head, keeping it in vertical position. The knob “1.1” must be
turned leftwards during this connecting or disconnecting. After the insertion turn the knob in vertical position again.
FLEXIBLE HOSE CONNECTION
After that the carpet sweeper is insert into the brush head connect the connection “2.1” to the upper carpet sweeper cover.
The connection “2.2” must be keep in the low part of the upright, reaching the brush head
joint.
OPERATION/STAND-BY
To start operation, press the block pedal “3.1” and tilt the carpet sweeper backwards, after push on start switch. To stop
operation, switch off keeping it in vertical position.
Attention:
Never drive the operating carpet sweeper above its own electric cable. Lift the carpet sweeper when going into stairs or
high thresholds.
fig. 3
fig. 2
fig. 1
REVISIONE N°05/001
ING. O. FIORENTINI S.p.A.
INDUSTRIAL CLEANING MACHINES
5
MANUAL SUCTION/BRUSH SUCTION
The carpet brush starts automatically when the manual suction pipe is located in its seat on the motor casing. If the
manual suction pipe is removed from its seat to manually suck the dust, the carpet brush automatically stops.
ADJUSTMENT OF THE CARPET BRUSH
The carpet brush can be adjusted according to the height of the carpet. You can reach the required position turning the
adjusting knob “4.1” and choosing among the 4 positions available. The chosen position can be read in the corresponding
display.
Position 1 -low pile carpet
Position 4 -very high pile carpet
BRUSH ELECTRONIC CONTROL
The electronic control of the brushes checks continuously the brush operation (fig. 5).
Your carpet cleaner has several built in safeguards to protect components from overload damage. The electronic circuitry
that operates the red light on the base indicates that the motor is overloading because the brush height is set too low or
there is debris hindering the movement of the brush roller.
If the overload is excessive circuitry will shut of the brush motor and the red light will stay on until the problem is
corrected. When the problem is corrected turn the switch off, wait for a moment and turn it back on. Make sure you
unplug the machine while inspecting the brush roller for debris.
Green light: regular brush operation
Green and red light: if you have the adjusting knob in position 1, control if the brush is in good condition and no dirty
clogs the rotation of the brush. If the red light continues change the brush.
In the position 2-3-4 adjusting knob for have less pressure on carpet. If you are in position 2, adjust knob at position 3.
Red light: locked brush (see Care and Maintenance)
RED LIGHT (bag full light), placed in the upper cover of the upright .
If warning light comes on, check if the red light goes on, check if:
a) the paper filter is full
b) the carpet brush is clogged
c) the vacuum hose is clogged
Then replace the filter or eliminate obstructions.
green light on
red light on green and red light on
fig. 5
fig. 4
REVISIONE N°05/001
ING. O. FIORENTINI S.p.A.
INDUSTRIAL CLEANING MACHINES
6
Notice: during operation with the suction hose, the manual pipe can get closed. The light will go on but there is no any
failure.
PAPER BAG REPLACEMENT
To replace paper bag open the upper cover of the carpet sweeper. Pull out the paper bag.
BRUSH STRIP REPLACEMENT
Unscrew the 3 screws placed under the brush head “6.2” remove out the brush, remove the RH support “6.3” and remove
the brush strip “6.1” and replace it with new one.
TROUBLESHOOTING
Blocked brush:
The brush motor is stopped by the electronic unit built-in in the carpet sweeper. The red light shows this state.
Remedy: Disconnect the carpet sweeper from mains, check if the brush is dirty and remove any possible blocking object.
Restart the carpet sweeper.
Clogged hose:
Stop the carpet sweeper, remove the hose from the brush head. Draw the hose in horizontal position and start the carpet
sweeper. If the obstruction still persists, remove it by means of a stab or similar mean.
TECHNICAL DATA
Suction data:
Vacuum motor: 3.8 A
Water lift: 70 inches
Air flow: 95 cfm (cubic feet a minute)
Voltage: 220 Volt, 60 Hz
Brushes:
Brush motor: 130 Watt
Traction: timing belts
Brush stripe: replaceable
Dimensions and Weight:
Height: 50 inches
Width: 14 inches
Weight: 18 lb
fig. 6
REVISIONE N°05/001
ING. O. FIORENTINI S.p.A.
INDUSTRIAL CLEANING MACHINES
7
REVISIONE N°05/001
ING. O. FIORENTINI S.p.A.
INDUSTRIAL CLEANING MACHINES
8
N.Position Code Num Qta
Descrizione Description Description
F35.01.001 KT037 1 ASSEMB.TUBO FLEX F350E/2*FANT* FLEX.HOSE ASSEMBLY ASS.TUYAU FLEX F350E/
F35.01.002 PY260 1 CAVO 3x1 SPINA EUROPEA ELECTRIC CABLE CABLE SJT 3X18 AWG105
F35.01.003 MR013 1 IMPUGNAT.GUIDA BATT.NERO*FANT* HANDLE GRIP POIGNEE NOIR
F35.01.004 VC302 2 VITE CILIN. TAGLIO M3x20 UNI 7689- SCREW M3x20 VIS
F35.01.005 PY566 1 CAVALLOTTO RAGGIATO BOLT PONT
F35.01.006 VC200 1 VITE CILIN.CROCE M4x12 UNI 7687 SCREW M4x12 VIS
F35.01.007 PI091 1 SUPPORTO TUBO ASPIRAZIONE SUCTION HOSE SUPPORT SUPPORT TUYAU
F35.01.008 CZ032 1 COPERCHIO CORPO CENTRALE TOP COVER COUVERCLE
F35.01.009 ML109 1 MOLLA CHIUSURA COPERCHIO CLOSING COVER SPRING RESSORT
F35.01.010 TO024 1 PIASTRA CHIUSURA COPERCHIO CLOSING COVER PLATE PLAQUE COUVERCLE
F35.01.011 VD223 4 VITE AUTOFIL.TPS 3,5 X 16 DIN 7982 SELF-THREADING SCREW VIS
F35.01.012 VD212 4 VITE AUTOFIL. TPS 2,9x13 DIN 7982 Z SELF-THREADING SCREW VIS
F35.01.013 SF040 1 SACCO CARTA PAPER BAG SAC EN PAPIER
F35.01.014 CL031 1 CESTELLO CONTENITORE SACCO CARTA PAPER BAG CAGE PANIER SAC EN PAPIER
F35.01.015 KT036 1 ASSEMBLAGGIO TUBO RIGIDO RIGID WAND ASSEMBLY ASS. TUYAU RIGIDE
F35.01.016 PY396 1 PASSACAVO IN PVC NERO CABLE RETAINER PASSE-CABLE
F35.01.017 VD222 2 VITE AUTOFIL. TPS 3,5x13 DIN 7982 Z SELF-THREADING SCREW VIS
F35.01.018 PI090 1 PIASTRINA SUPPORTO FERMACAVO E BASE SUPPORT PLAQUE PLAQUE
F35.01.019 PY308 1 FERMACAVO IN PLASTICA PICCOLO CABLE HOLDER ARRETE-CABLE
F35.01.020 VD212 2 VITE AUTOFIL. TPS 2,9x13 DIN 7982 Z SELF-THREADING SCREW VIS
F35.01.021 IN057 1 MICRO INTERRUTTORE LUNG.25 MICROSWITCH 25mm MICRO-INTERRUPTEUR
F35.01.022 VA212 1 VITE AUTOFILET. TC 2,9x16 DIN7981 Z SELF-THREADING SCREW VIS
F35.01.023 VA210 2 VITE AUTOFILET. TC 2,9x9,5 DIN7981 SELF-THREADING SCREW VIS
F35.01.024 PY568 1 SCHEDA CONTROLLO SACCO CARTA PIENO PAPER BAG CONTROL CAR PLATINE CONTROL SAC P
F35.01.025 VD212 4 VITE AUTOFIL. TPS 2,9x13 DIN 7982 Z SELF-THREADING SCREW VIS
F35.01.026 CR006 2 CERNIERA COP.CONTENITORE SACCO*FANT COVER HINGE CHARNIERE
F35.01.027 TO023 1 CHIUSURA IMPIANTO ELETTRICO CLOSING ELECTRIC SYST FERMETURE INST.ELECTR
F35.01.028 MR012 1 ASTA MANICO IN ALLUMINIO ALUMINIUM HANDLE TIGE EN ALU
F35.01.029 VC202 2 VITE CILIN.CROCE M4x10 UNI 7687 SCREW M4x10 VIS
F35.01.030 IN041 1 INTERRUTTORE BIPOLARE SWITCH INTERRUPTEUR
F35.01.031 LP022 1 SPIA BATTITAPPETO SACCO PIENO PILOT LAMP PROTECTION TEMOIN
F35.01.032 CN073 1 CORPO CENTRALE BATTITAPPETO UPRIGHT CENTRAL BODY CORP CENTRAL
F35.01.033 MR010 1 MANIGLIA SOLLEVAMENTO BATTITAPPETO LIFTING HANDLE POIGNEE DE SOULEVEMEN
F35.01.034 VA212 1 VITE AUTOFILET. TC 2,9x16 DIN7981 Z SELF-THREADING SCREW VIS
F35.01.035 IN076 1 MICRO INTER.CABL.*FANT* MICRO SWITCH MICRO-INTERRUPTEUR
F35.01.036 PY559 1 PRESSACAVO PG7 IP54 PA6 CABLE RETAINER PRESSE-CABLE
F35.01.037 CZ031 1 COPERCHIO SUPERIORE PORTA TURBINA VACUUM MOTOR HOLDER COUVERCLE SUP.
F35.01.038 PI093 1 PULSANTE MICRO SICUREZZA MICRO SWITCH POUSSOIR MICRO-INT
F35.01.039 VA260 2 VITE AUTOFILET. TC 3,5x16 UNI 6954/ SELF THREADING SCREW VIS
F35.01.040 VA251 1 VITE AUTOFILET. TC 3.9x13 UNI 6954/ SELF THREADING SCREW VIS
F35.01.041 TO016 1 COPERCHIO X VALVOLA SAFETY VALVE COVER COUVERCLE
F35.01.042 ML085 1 MOLLA COPERCHIO VALVOLA SP.1 mm SAFETY VALVE COVER SP RESSORT
F35.01.043 TO015 1 VALVOLA SAFETY VALVE VANNE
F35.01.044 LR1047 1 GUARNIZIONE MOTORE ASPIRAZIONE VACUUM MOTOR GASKET MOT.ASP. JOINT
F35.01.045 MO464 1 MOTORE ASPIRAZIONE 220V VAC MOTOR 750W MOTEUR ASPIRATION 750W
F35.01.046 MP191 2 CARBONCINO MOTORE ASPIRAZIONE DD VAC MOTOR CARBON BRUS CHARBON MOT.BROSSE
F35.01.047 LR1411 1 GOMMA POSTERIORE PROTEZIONE RUBBER GASKET CAOUTCHOUC
F35.01.048 FO033 1 INSONORIZZ. VANO MOTORE POLIESTIC P SOUND INSULATION MOUSSE INSONORISATION
F35.01.049 SF088 1 FILTRO DI SCARICO 150x160x20 FILTER FILTRE
F35.01.050 CZ030 1 COPERCHIO FILT.SCAR.*FANT* FILTER COUGH COUVERCLE FILTRE DECH
F35.01.051 CC013 1 FERMO COP. FILTRO SCAR*FANT* FILTER RETAINING CLAM FERMETURE COUVERCLE
F35.01.052 VC252 1 VITE CILIN.CROCE M3x10 DIN7985 SCREW M3x10 VIS
F35.01.053 DD201 3 DADO M3 UNI 5588/65 NUT M3 ECROU
F35.01.054 VB213 4 VITE CIL.BRUGOLA M5X30 UNI 5931/77 SCREW M5x30 VIS
F35.01.055 CB030 1 PORTA TURBINA BATTITAPPETO MOTOR HOUSING LOGEMENT TURBINE
F35.01.056 VB213 1 VITE CIL.BRUGOLA M5X30 UNI 5931/77 SCREW M5x30 VIS
F35.01.057 PI057 1 LEVA COMANDO BLOCCO LOCKING CATCH LEVIER
F35.01.058 PI056 1 LEVA BLOCCO BASAMENTO A PARTE SUPER LOCKING CATCH LEVIER
F35.01.059 DD202 3 DADO M4 UNI 5588/65 NUT M4 ECROU
F35.01.060 PE162 1 PERNO CONTATTO MESSA A TERRA BASAME STATIC GROUND PIN PIVOT
F35.01.061 DD252 1 DADO AUTOBLOCCANTE M5 SELF-LOCKING NUT M5 ECROU DE SURETE
F35.01.062 AS016 1 LEVA FISSAGGIO BASAMENTO A PARTE SU LOCKING-ROD LEVIER FIXATION BASE
F35.01.063 LR2014 2 LINGUETTA FERMASSALE FEATHER PLATINE
F35.01.064 VA264 2 VITE AUTOFILET. TC 3.5x13 UNI 6954/ SELF THREADING SCREW VIS
F35.01.065 PY434 1 PROTEZIONE CONTATTI CONNECTION PROTECTION PROTECTION CONTACTS
F35.01.066
TO022 1 COPERCHIO INFERIORE PORTA TURBINA SUCTION MOTOR COVER COUVERCLE INF.
F35.01.067 VA260 4 VITE AUTOFILET. TC 3,5x16 UNI 6954/ SELF THREADING SCREW VIS
F35.01.068 GO071 1 GUARNIZIONE COPERCHIO SACCO BATTITA GASKET JOINT COUVERCLE SAC
F35.01.069 SF087 1 FILTRO ASPIRAZIONE PPI20 SUCTION FILTER FILTRE ASPIRATION
REVISIONE N°05/001
ING. O. FIORENTINI S.p.A.
INDUSTRIAL CLEANING MACHINES
9
F35.01.070 VC251 2 VITE CILIN.CROCE M3x8 DIN7985 SCREW M3x8 VIS
F35.01.071 EE027 1 MANICOTTO GIREVOLE MASCHIO BLACK ROTATING SLEEVE EMBOUT
F35.01.072 EE033 1 RACCORDO TUBO FLEX FLEXIBLE HOSE UNION RACCORDEMENT TUYAU
F35.01.073 FF075 1 TUBO FLEX ANIMA ACC. D.40 L.560mm FLEXIBLE HOSE TUYAU FLEX
F35.01.074 RO909 1 RONDELLA DENTATA D.4 UNI 3706 WASHER RONDELLE
F35.01.075 FF019 1 TUBO COLLEGAMENTO PRESS.-SACCO *FAN CONNECTION HOSE PRESS TUYAU
F35.01.076 KT050 1 ASSEMBLAGGIO TUBO ASPIRAZIONE COMPLETO COMPLETE WAND ASSEMBLY ASS. TUYAU RIGIDE
F35.01.077 HH034 1 TUBO RIGIDO INTERNO RIGID WAND TUYAU RIGIDE
F35.01.078 MR014 1 COPERTURA MANICO COVER COVER
F35.01.079 GG011 1 LINGUETTA MANICO TONGUE CLAVETTE
F35.01.080 PI095 1 SUPPORTO PER TUBO ASPIRAZIONE SUPPORT SUPPORT
REVISIONE N°05/001
ING. O. FIORENTINI S.p.A.
INDUSTRIAL CLEANING MACHINES
10
REVISIONE N°05/001
ING. O. FIORENTINI S.p.A.
INDUSTRIAL CLEANING MACHINES
11
N.Position Code Num Qta
Descrizione Description Description
F35.02.001 LP023 2 PROTEZIONE SPIA TRASP. COP. BASAMEN PROTECTION PROTECTION TEMOIN
F35.02.002 CB022G 1 COPERCH.BASAM.*FANT* BASE COVER COUVERCLE BASEMENT
F35.02.003 LR2016 2 SUPPORTO SNODO SWIVEL NECK SUPPORT W SUPPORT ARTICULATION
F35.02.004 LR2405 2 BOCCOLA IN DERLIN GRANDE BUSH JOINT DOUILLE ARTICULATION
F35.02.005 LR2086 2 BRONZINA SNODO BUSH JOINT DOUILLE ARTICULATION
F35.02.006 CZ021 1 COPERCHIO SNODO JOINT COVER COUVERCLE ARTICULATIO
F35.02.007 VA250 2 VITE AUTOFILET. TC 3,9X16 UNI 6954/ SELF THREADING SCREW VIS
F35.02.008 CW081 1 COPPIA CONTATTI MASCHIO SNODO*FANT* WIRE ON SWIVEL NECK CONTACT MALE
F35.02.009 CQ020 1 SNODO SWIVEL NECK ARTICULATION
F35.02.010 GO063 2 FELTRO TENUTA X BASAMENTO E COPERCH FELT SEAL JOINT BASE
F35.02.011 GO061 1 PROTEZIONE SCHEDA ELETTRONICA ELECTRONIC CARD PROTE PROTECTION PLATINE EL
F35.02.012 PY432 1 SCHEDA ELETTRONICA 230V F350 ELECTRONIC CARD 220V PLATINE ELECTRONIQUE 220V
F35.02.013 CI025 1 CINGHIA DENTATA HTD 339-3M 8 Q BELT COURROIE CRANTEE
F35.02.014 PP055 1 PULEGGIA MOT.SPAZ.*FANT* - PULLEY POULIE MOT. BROSSE
F35.02.015 FT015 1 PARATIA ARIA X MOTORE BATTITAPPETO FILTER CLOISON
F35.02.016 GO062 1 GUARNIZIONE ADESIVA CALOTTA MOTORE GASKET JOINT
F35.02.017 MO262 1 MOTORE SPAZZOLA 230V BRUSH MOTOR 230V MOTEUR BROSSE 230V
F35.02.018 VA254 2 VITE AUTOFILET. TC 3,9x19 UNI 6954/ SELF TREADING SCREW 3 VIS
F35.02.019 RO201 4 RONDELLA NORMALE DIAM. 4 UNI 6592/6 WASHER D4 RONDELLE
F35.02.020 AS010 1 LEVA SUPP.FULCRO PARTE SUPERIORE SUPPORT LEVER LEVIER
F35.02.021 ML086 1 MOLLA sp.filo 0.8mm SPRING RESSORT
F35.02.022 PP056 1 PULEGGIA RULLO SPAZZOLA BRUSH PULLEY POULIE
F35.02.023 PI059 2 SUPPORTO CUSCINETTO ALBERO SPAZZOLA BRUSH SUPPORT SUPPORT DE BROSSE
F35.02.024 CS033 2 CUSCINETTO 626-2RS1 BEARING ROULEMENT
F35.02.025 CQ019 1 RULLO SPAZZOLA BRUSH BROSSE
F35.02.026 RF010 1 REFIL SPAZZOLA BATT. 350*FANT* BRUSH STRIP REFIL BROSSE
F35.02.028 VA262 1 VITE AUTOFILET. TC 3.5x25 UNI 6954/ SELF THREADING SCREW VIS
F35.02.029 ML087 1 MOLLA sp.filo 0.8mm SPRING RESSORT
F35.02.030 LR0308 2 SEEGER BLOCCO RUOTE SEEGER SEEGEER ROUES
F35.02.031 LR2012 2 RUOTA PER BATTITAPPETO WHEEL ROUE
F35.02.032 RO203 2 RONDELLA NORMALE DIAM. 6 UNI 6592/6 WASHER D6 RONDELLE
F35.02.033 LR2010 1 MOLLA ASSALE RUOTE WHEELS AXLE SPRING RESSORT AXE ROUES
F35.02.034 LR2014 3 LINGUETTA FERMASSALE FEATHER PLATINE
F35.02.035 VA251 3 VITE AUTOFILET. TC 3.9x13 UNI 6954/ SELF THREADING SCREW VIS
F35.02.036 LR2009 1 ASSALE X RUOTE WHEEL AXLE AXE ROUES
F35.02.037 PI089 1 PEDALINO INCLINAZIONE FOOT PEDAL PEDAL
F35.02.038 CB021G 1 BASAMEN.RULLO SPAZ.*FANT* CHASSIS BASEMENT BROSSE
F35.02.039 LR4013 1 POMELLO COM.ALT.SPAZ*FANT* - BRUSH HEIGHT ADJUSTME POMMEAU REGL.HAUTEUR
F35.02.040 VA251 2 VITE AUTOFILET. TC 3.9x13 UNI 6954/ SELF THREADING SCREW VIS
F35.02.041 VC218 4 VITE CILIN.CROCE M5x45 UNI 7687 SCREW M5x45 VIS
F35.02.042 BU010 1 BUMPER PARACOLPI BUMPER BUMPER
F35.02.043 AS011 1 ASSALE RUOTE REGOL.ALTEZZA RULLO SP WHEELS AXLE AXE ROUES
F35.02.044 RT081 3 RUOTA ASSALE REGOL.RULLO SPAZZOLA BRUSH ADJUSTMENT WHEE REGLAGE BROSSE
F35.02.045 GO068 1 GUARNIZ.ANTERIORE PATTINO 350(RIC.D GASKET GARNITURE SUCEUR
F35.02.046 GO027 1 GUARNIZIONE PATTINO 350 GASKET GARNITURE SUCEUR
F35.02.047 VI044 2 ROSETTA IN PLASTICA TIPO MP15.4 WASHER RONDELLE
F35.02.048 CQ021 1 PATTINO IN ACCIAIO STAINLESS AND STELL S SUCEUR EN ACIER
F35.02.049 VS211 2 VITE SVASATA A CROCE M 5x12 UNI 768 SCREW M5x12 VIS
F35.02.050 VS202 1 VITE SVASATA A CROCE M 4x10 UNI 768 SCREW M4x10 VIS
F35.02.051 KS031 1 ASS.SNODO COMP/MES.TER.*FANT* COMPLET JOINT ARTICULATION COMPL.
F35.02.052 KS022 1 RULLO SPAZ.COM.F350E *FANT* COMPLETE BRUSH BROSSE COMPLETE
F35.02.053 KX011 1 ASSALE RUOTE COM.*FANT* WHEELS AXLE COMPLETE AXE ROUES
F35.02.054 KS028 1 ASS.PATT.C/GUARN.F350*FANT* STAINLESS AND STELL A ASS. SUCEUR JOINT VIS
F35.02.055 MP355 2 CARBONCINO C/CONDOTTO X MOTORE 230V CARBON BRUSH CHARBON MOTEUR
F35.02.056 VI045 1 ROSETTA IN PLASTICA TIPO MP15.3 WASHER RONDELLE
F35.02.057 ML108 1 MOLLA CONTATTO MESSA A TERRA SNODO ENCLOSING COVER SPRIN RESSORT
REVISIONE N°05/001
ING. O. FIORENTINI S.p.A.
INDUSTRIAL CLEANING MACHINES
12
REVISIONE N°05/001
ING. O. FIORENTINI S.p.A.
INDUSTRIAL CLEANING MACHINES
13
N.Position Code Num Qta Descrizione Description Description
F35.03.001 PY260 1 CAVO 3x1 SPINA EUROPEA ELECTRIC CABLE CABLE SJT 3X18 AWG105
F35.03.002 IN041 1 INTERRUTTORE BIPOLARE SWITCH INTERRUPTEUR
F35.03.003 CW073 1 CAVETTO COLLEGAMENTO INTERR.MICRO S ELECTRIC CABLE SWITCH CABLE CONN.MICRO-INTE
F35.03.004 IN057 1 MICRO INTERRUTTORE LUNG.25 MICROSWITCH 25mm MICRO-INTERRUPTEUR
F35.03.005 PY568 1 SCHEDA CONTROLLO SACCO CARTA PIENO PAPER BAG CONTROL CAR PLATINE CONTROL SAC P
F35.03.007 CW076 1 CAVETTO 2x1 COLL. SCHEDA MORSETTIER ELECTRIC CABLE CONTRO CABLE 2X1
F35.03.008 PY346 1 MORSETTIERA MAMMUT 3 POLI PA27 TERMINAL BOARD MAMMUT BORNIER
F35.03.009 MO464 1 MOTORE ASPIRAZIONE 220V VAC MOTOR 230 V MOTEUR ASPIRATION 230 V
F35.03.010 CW077 2 CAVETTO MESSA A TERRA MOTORE ASP./B GROUNDING CABLE CABLE MISE AU SOL
F35.03.011 CW078 1 CAVETTO MICRO SICUREZZA BASAMENTO ELECTRIC CABLE MAMMUT CABLE MICRO DE SURETE
F35.03.012 IN057 1 MICRO INTERRUTTORE LUNG.25 MICROSWITCH 25mm MICRO-INTERRUPTEUR
F35.03.013 CW079 2 CAVETTO MOTORE ASPIRAZIONE ELECTRIC CABLE MAMMUT CABLE MOTEUR ASP.
F35.03.014 CW080 1 COPPIA CONTATTI FEMMINA BASAMENTO F CONTACT PLUG COUPLE CONTATS FEMELL
F35.03.015 PY432 1 SCHEDA ELETTRONICA 230V F350E ELECTRONIC CARD 230V PLATINE ELECTRONIQUE 230V
F35.03.016 MO262 1 MOTORE SPAZZOLA 230V BRUSH MOTOR 230V MOTEUR BROSSE 230V
F35.03.017 CW081 1 COPPIA CONTATTI MASCHIO SNODO*FANT* WIRE ON SWIVEL NECK CONTACT MALE
F35.03.018 ML108 1 MOLLA CONTATTO MESSA A TERRA SNODO ENCLOSING COVER SPRIN RESSORT
F35.03.019 CW074 1 CAVETTO ANTISTATICA ANTISTATIC CABLE CABLE ANTISTATIQUE
REVISIONE N°05/001
ING. O. FIORENTINI S.p.A.
INDUSTRIAL CLEANING MACHINES
14
N.Position Code Num Qta
Descrizione Description Description
F35.04.001 HH024 1 TUBO PROLUNGA TUBE EXTENSION RALLONGE
F35.04.002 LL007 1 LANCIA PIATTA BATTITAPPETO CREVICE TOOL SUCEUR PLAT
F35.04.003 ZZ060 1 PENNELLO BATTITAPPETO ROUND BRUSH BROSSE RONDE
F35.04.004 SF040 1 SACCO CARTA PAPER BAG SAC EN PAPIER
F35.04.005 SF041 1 10 SACCHI CARTA BATTITAPPETO 10 PAPER BAGS 10 PC.SAC PAPIER
REVISIONE N°05/001
ING. O. FIORENTINI S.p.A.
INDUSTRIAL CLEANING MACHINES
15
Mat. n.
Serial no. _____________________
Nr. de serie
Data di spedizione
Date of shipment _____________________
Date de spedition
ING. O. FIORENTINI S.p.A.
“T
HE BEST IN FLOOR MACHINES
”
FILIALI:
20132 MILANO – Fax. 02/2592779
Via Palmanova 211/a – Tel. 02/27207783 - 2564810
00012 Guidonia Montecelio (ROMA) – Fax. (0774)353419 - 353314
Via Ponte Corvo 20 – Tel. (0774)357184 - 353015
STABILIMENTO:
50030 PIANCALDOLI (FI) – Fax. 055/817144
Loc. Rombola – Tel. 055/8173610
Distributed by:
Loading...