Traveler 1400MM
User Manual
FINWING TECHNOLOGY WWW FINWINGHOBBY COM..
PATENT OWNER FINWINGHOBBY:
Subscribe WeiChat
Fin inghobby
Finwinghobby
()
Like us
Facebook Page()
Like us
Facebook Page
..
as introductions to ing this
www
This manual user on how to build RC plane.
Please visit the finwinghobby com official website for more introductions.
Please read through the manual before installation and flying
Warning:
1 This model airplane is not a toy not recommended for children under 14 years old., ,
2. Be cautious and prepared while flying this plane as a range of issues could lead to a crash
including the environment/weather, speed, pilot error, improper building/testing,
interference or other component failures
3. Flying field: Choose an adequate flying space at least 100 meters long/wide and in an unpopulated
and non-built up area for safe flying. This includes avoiding flying over cities or other populated areas.
4. Please don't fly this model airplane in bad weather including rainy and/or windy environments.
5. Remember to unplug your flight/video battery when not in use to avoid any interference to others
who might be on similar channels.
6. Please remember switch on the transmitter first before connecting the battery, and disconnect
the battery first before switching off your transmitter.
7. Keep away from the propeller when the Airplane is powered as it can be dangerous and could
lead to injury. Keep the powered plane away from children at all times to avoid any accidents or injury.
.
Subscribe
WeiChat
Finwinghobby
Subscribe
WeiChat
Finwinghobby
Will post the information on time to weixin and facebok
once we have new airplane for sales or big discount promotions
Bethefirstonetoknow!
()
Like us
Facebook Page()
Like us
Facebook Page
H
Black White EPP and EPO/
L
R
Center of Leading edge
Center of Rear edge
Neutralize Elevator control surface first
Plane levelly at a platform measure the stabilizer before ready to fly
Hole
Forward
Backward
-
+
CG Setting at Hole H.""
LR=
LR=
RLabout 1 2MM> -> -
CG Setting at H Forward 2 4MM.-
It s inaccurate measurement if building not completely done' !
0 3MM Thin washers not thicker washers.
we also have flown good without washers
but seems added washer is better most of the time
must
0 3MM Washers included for all V2 package
you install washers if your think
your plane tendency to nose up climbing
After further adjust the CG properly
.
.
..
have to
How to find out the perfect CG ?
Generally most of us measure CG by fingers and inevitable differently by different people
For example if you noticed plane a little nose up flying landing then moving CG A little forward
but if plane likely to be nose down landing then moving CG A little backward 2040mm
,
,.
, . .(.-. )
Recommended Add washers
WWW finwinghobby com..
CG Setting.
Main Wings Building
Left and right wing building is exactly the same
1
2
3
Glue to install spars to this wing first
Install foam cover
Be sure metal part to be outward
WWW finwinghobby com..
Length is differently
Install extension
gluing to all contact surface
Long spar
Short spar
4
At last instll plywood and foam cover to extension wing
Recommend wrapping tape filming along the joint line
WWW finwinghobby com..
Main Wings Building
Left and right wing building is exactly the same
WWW finwinghobby com..
Fuselage Gluing Covers and Plywood()
Step 1
gluing shoulder cover
#
Step
gluing Plywood
#3
Step #2
Gluing fuselage tail cover
Important Note be sure let glue dry at least 12 hours before installing other parts:
Be careful I m big hole
don t use that small hole one
'
'
Be careful I m big hole
don t use that small hole one
'
'
Step Gluing
Motor Mount plywood
#4
Plywood
WWW finwinghobby com..
Fuselage Tail EPP EPO&(/)
Linkage
Linkage
Screw secure the lockers
Note Black EPP White EPP and White EPO is the same:/
Cut off
Cut off
For Metal linkage
For servo Horn
ForWingLock
Φ20.
Φ23.
Φ30.
Use hobby knife cut a hole let ESC and Servo wire pass through
Note Black EPP White EPP and White EPO is the same:/
ESC pass through the hole like this
WWW finwinghobby com..
Fuselage EPP EPO(/ )
Servo Horn
Choose the hole or the second hole won t be
big difference recommend try the top hole
:
'
,
top
#-Tail Boom
Gluing Cover and Carbon Strip
#Vertical wing
Gluing plywood and Carbon Strip
Now please let glue dry about hours
before continuing the next step
8
Cut off
WWW finwinghobby com..
T Tail-
T Tail-
#-
Glue vertical wing to the tail boom
Put vertical wing inside immediately
after gluing to all the contact surface
irremovable dry at least 12 hours
Warning Reminder:&
Please must have to glue vertical wing to the tail firmly and irremovable dry at least 12 hours.
this is the only way to secure stabilizers,
there is a horizontal mark line on the vertical wing ,keep it parallel to the tail surface.
it's absolutely dangerous(wrong) dicision if you want to make the vertical stablizer detachable or
removable in future by hot glue, tape, no mattery whatever way you think it's solid..
even if stabilizer not drop but 100% will loose during flight, 100% sure a loosing stabilizer
is a unstable "stabilizer and cause any weird accident, out of control, etc.
A well glued vertical stabilizer won't loose or drop no matter what kind of impact,
stabilizer is still part of the whole tail even if fuselage, mainwing crashed to hundrends of pieces
WWW finwinghobby com..
T Tail-
Enlarge the servo bay to have enough
space for the servo arm moving freely
Black EPP White EPP and White EPO is the same/
WWW finwinghobby com..
Install servos(/-)Fuselage Main Wing
Neutralize servo first
Install servo as photos displayed
Black EPP White EPP and White EPO is the same
/
Install servos()Use metal gear servo
The bottom hole
The holefirst
The holefirst
The bottom hole
Install servos()Use Metal mear servo
WWW finwinghobby com..
Motor ESC Propeller//
Solder in parallel
Note Move the heat shrink tubing inside first:
Black EPP White EPP and White EPO is the same/
WWW finwinghobby com..
Motor ESC Propeller//
Use the short wire servos
for rudder and elevator
if you have Finwing Stock
V2 ARF Combo
7 0CM.
:,
'
FYI during my later testing I removed the rudder servo
basically can t tell any difference without rudder
till flying very good without rudder
S
WWW finwinghobby com..
T Tail-
Launch Cart is not must to everybody OPtions only
Good to enjoying rolling take off and beginner
not included by kits ARF
()
</>
Front wheel
4 0 Hole.Φ
Rear wheel
3 0 Hole.Φ
Find out all the parts gluing the metal washers first
,
Φ40.
Φ30.
WWW finwinghobby com..
Launch Cart
What is this for ?
Use it as cushion if you found the locker become loose
WWW finwinghobby com..
EVA Cushion
Loading...