Finlux 55S8090-T User Manual

happy Finnish
55in LED TV
55S8090-T
Customer Helpline Number: 0845 459 5282
Owner’s manual
Contents
Environmental Information ..................................... 2
Accessories included .............................................. 3
TV - Features ......................................................... 3
Safety Precautions and Important Information ....... 3
Viewing the TV ...................................................... 4
TV Control Buttons & Operation ............................. 4
Operation with the Buttons on the TV ..................... 4
Operation with the Remote Control ........................ 4
Remote Control ..................................................... 5
Inserting the Batteries into the Remote Control...... 7
Connect Power & Antenna ..................................... 7
Switching On/Off ..................................................... 7
First Time Installation.............................................. 7
Media Playback via USB Input ............................... 8
Quick Menu ............................................................ 9
Changing Image Size: Picture Formats .................. 9
Using the Channel List ........................................... 9
Appendix C: AV and HDMI Signal Compatibility
(Input Signal Types) .............................................. 22
Appendix D: Supported File Formats for USB Media
Browser ................................................................ 23
Appendix E: Supported DVI Resolutions .............. 24
SKY Remote Control Code ................................... 24
Specications ....................................................... 24
English - 1 -
Power cord and plug
The power cord plug should be easily accessible. If there is lightning or storms, or if the TV is not going to be used for a while (e.g. if going away on holiday), disconnect the TV set from the mains.
•Do not place the TV, furniture, etc. on the power cord or pinch the cord.
Handle the power cord by the plug, do not unplug the TV by pulling the power cord.
Never touch the power cord/plug with wet hands as this could cause a short circuit or electric shock.
Never make a knot in the power cord or tie it with other cords.
Power cords should be placed in such a way that they are not likely to be stepped on or provide a trip hazard.
• A damaged power cord/plug can cause re or give
you an electric shock. When damaged it must be
replaced, this should only be done by qualied
personnel.
Moisture and Water
•Do not use this TV in a humid or damp place (avoid using in the bathroom or near the kitchen sink)
•Do not expose this TV to rain or water, as this may be dangerous.
If any solid object or liquid falls into the cabinet, unplug the TV and have it checked by qualied
personnel before operating it any further.
Ventilation
The slots and openings on the TV set are intended for ventilation and to ensure reliable operation.
To prevent overheating, these openings must not be blocked or covered in any way.
Heat sources and Flames
Do not expose the TV to direct sunlight or other heat sources.
• The TV should not be placed near open ames or
sources of intense heat such as an electric heater.
• Ensure that no open ame sources, such as lit
candles, are placed on top of the TV.
Headphone Volume
Excessive sound pressure from earphones and headphones can cause hearing loss, please take care.
Wall Mounting (optional)
To prevent injury, this TV must be securely attached to the wall in accordance with the installation instructions.
Screen
Occasionally, a few non-active pixels may appear
on the screen as a xed blue, green or red point.
Please note that this does not affect the performance of your product.
• Take care not to scratch the screen with ngernails
or other hard objects.
Cleaning
Before cleaning, unplug the TV from the wall socket.
•Do not use liquid or aerosol cleaners. Only use a
soft, dry cloth.
Environmental Information
This television is designed to consume less energy to help save the environment. You can not only help to save the environment but you can also save money by reducing your electricity bills thanks to the energy efficiency features of this TV. To reduce energy consumption, you should take the following steps:
You can use the Power Save Mode setting, located in the Picture menu. If you set the Power Save Mode as Eco, the TV will switch to energy-saving mode and the luminance level of TV set will be decreased to the optimum level. Note that some picture settings will be unavailable to be changed when the TV is in Power Save Mode.
If Picture Off is selected, “Screen will be off in 15 seconds.” message will be displayed on the screen. Select PROCEED and press OK to continue. The screen will be off in 15 seconds.
When the TV is not in use, please switch off or disconnect the TV from the mains plug. This will also reduce energy consumption.
It is highly recommended that you activate the Power Save Mode setting to reduce your annual power consumption.
1) If the TV does not receive any input signal (e.g. from an aerial or HDMI source) for 5 minutes, the TV will go into standby. When you next switch-on, the following message will be displayed:
“Standby Cause No Signal”
Press OK to continue.
2) If the TV has been left on and not been operated for 4 hours, the TV will go into standby. When you next switch-on, the following message will be displayed.
“Standby Cause No Operation”
Press OK to continue.
English - 2 -
Accessories included
Remote Control
Batteries: 2 x AAA
Instruction Book
Side AV Connection Cable
WiFi Dongle
USB Cable
NeroHome Media CD
TV - Features
Remote controlled colour LCD TV
Fully integrated digital tuner
DVB-T2 Compliant
HDMI Inputs are for connecting a device that has
a HDMI socket
USB input
10000 programmes
OSD menu system
Scart socket for external devices (such as DVD
Players, PVR, video games, etc.)
Stereo sound system
Teletext
Headphone connection
Automatic programming system
Manual tuning
Automatic power down after up to six hours
Sleep timer
Child lock
Automatic sound mute when no transmission
NTSC playback
AVL (Automatic Volume Limiting)
PLL (Frequency Search)
PC input
Plug&Play for Windows 98, ME, 2000, XP, Vista,
Windows 7
Game Mode (optional)
Ethernet (LAN) for Internet connectivity
802.11n WiFi Support via USB dongle
DLNA
100Hz frequency scan
Safety Precautions and Important Information
Please read these instructions fully before installing or operating.
Preparation
Place the device on a solid even surface. For ventilation purposes, leave a free space of at least 10 cm all around the set. Do not place any objects on top of the set. Use this device in moderate climates. Operation temperature and operation humidity: 5ºC up to 45ºC, 85% humidity max. Note: Don’t block ventilation holes.
Intended Use
This device is used to receive and display TV programmmes. The different connection options expand the reception and display sources possible (various external devices). This device is only suitable for operation in dry interiors. This appliance is intended solely for private domestic use and may not be used for industrial and commercial purposes. We exclude liability in principle, if the device is not used as intended, or unauthorized
modications have been made. To operate your TV
in extreme ambient conditions may cause damage to the device.
WARNING: Never let people (including
children) with reduced physical, sensory or mental capabilities or lack of experience and / or knowledge use electrical devices unsupervised.
Children may not recognize the dangers of incorrect use. The swallowing of batteries can be fatal. Keep batteries out of reach of small children. If a battery is swallowed, immediately seek medical attention. Keep the packaging
lmsoutofreachofchildrentopreventtherisk
of suffocation.
Power source
The TV should be operated only from a 220-240 V AC, 50 Hz outlet.
Positioning the TV
For ventilation, please leave a clear space of at least 10cm all around the TV.
•Do not block the ventilation openings.
•Do not place the TV on sloping or unstable surfaces,
the TV may tip over.
To prevent damage to the TV, do not place any objects on top of the TV.
English - 3 -
Viewing the TV
TV Control Buttons & Operation
1. Up direction
2. Down direction
3. Programme/Volume / AV / Standby-On selection
switch
Operation with the Buttons on the TV
Volume Setting
You can move the control switch upward or downward for changing the volume. To increase volume, please move the switch upward. Move the switch downward to decrease the volume. A volume level scale (slider) will be displayed on the screen.
Programme Selection
First press the control switch once to change channel. You can move the switch upward to select the next programme or move it downward to select the previous programme.
Viewing Main Menu
Menu screen cannot be displayed by using the control switch.
AV Mode
Press the control switch consecutively until the source OSD is displayed on the screen.
Operation with the Remote Control
Press the MENU button on your remote control to display the main menu screen. Use the “ ” or “ ” buttons to select a menu tab and press the OK button to select option. Use the “ ” / “ ” or “ ” / “ ” buttons to select or set an item. Press BACK or EXIT or MENU button to quit a menu screen.
Input Selection
Once you have connected external systems to your TV, you can switch to different input sources. Press the
- (SOURCE)” button on your remote control consecutively to select the different inputs.
Changing Channels and Volume
You can change the channel and adjust the volume using the V+/- and P+/- buttons on the remote.
English - 4 -
Remote Control
1. Standby / On
2. Channel list
3. Volume up-down
4. Menu on/off
5. OK / Channel list / Conrm
6. Return / Back
7. Internet Portal
8. My button 1 / Youtube (*)
9. My button 2 (**)
10. Coloured buttons (Red, Green, Yellow, Blue)
11. Mono-Stereo Dual I-II / Current language
12. Fast rewind (in media browser mode)
13. Pause (in media browser mode) / Timeshift
recording
14. Programme recording
15. Play (in media browser mode)
16. Stop (in media browser mode)
17. Fast forward (in media browser mode)
18. Subtitle on-off / Subtitle (in media browser
mode)
19. Image size
20. Teletext - Mix
21. Media Browser
22. Electronic programme guide
23. Exit
24. Navigation buttons
25. Quick menu
26. Info / Reveal (in TXT mode)
27. Programme up/down
28. Mute
29. Previous programme / Now (in EPG mode)
30. Numeric buttons
31. AV / Source
TV
NOTE: The Remote Control range is approximately 7m
/ 23ft.
Using My button 1 (*)
This button’s main function is to run Youtube link. However, if you want to change this function, you can press MY
BUTTON 1 for ve seconds when on a desired source,
channel or link, until the “MY BUTTON IS SET” message
is displayed on the screen. This conrms that the selected
MY BUTTON is now associated with the selected function.
Note that if you perform rst time installation, MY BUTTON
1 will return to its default function.
English - 5 -
Using My Button 2 (**)
This button’s main function is to switch to DVB-T, broadcasts. However, if you press MY BUTTON 2 for
ve seconds, you can set a function to it as described
in My Button 1.
Note that if you perform a first time installation, MY BUTTON 2 will return to its default function.
Connections
AV Connection
Cable (supplied)
Scart
Connection
(back)
VGA
Connection
(back)
PC/YPbPr Audio
Connection
(back)
HDMI
Connection
(back & side)
S/PDIF Optical Out
(back)
S/PDIF
Side AV
Connection
(side)
Headphone Connection
(side)
USB
Connection
(side)
Connector Type Cables Device
Y BPRP
AUDIO L&R
SIDE AV
HEADPHONE
YPbPr Video
Connection
(back)
CI
Connection
(side)
CAM
module
Subwoofer
Connection
(back)
NOTE: When connecting a device via the YPbPr or Side AV input, you must use the supplied connection cables to enable connection. See the illustrations above. | To enable PC audio, you will need to use the PC/YPBPR CONNECTION cable’s WHITE & RED inputs. | If an external device is connected via the SCART socket, the TV will automatically switch to AV mode.| When receiving DTV channels (Mpeg4 H.264) or while in Media Browser mode, output will not be available via the scart socket. | When using the wall mounting kit (optional), we recommend that you plug all your cables into the back of the TV before mounting on the wall. | Insert or remove the CI module only when the TV is SWITCHED OFF. You should refer to the module instruction manual for details of the settings.
English - 6 -
Inserting the Batteries into the Remote Control
HDMI 1
HDMI 1
1. Lift the cover on the back of the remote upward gently.
2. Install two AAA batteries. Make sure to match the + and - ends of the batteries in the battery compartment (observe the correct polarity).
3. Replace the cover.
Connect Power & Antenna
IMPORTANT: The TV set is designed to operate on
220-240V AC, 50 Hz socket. After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the mains. Plug the aerial cable into the ANT socket on your TV.
Switching On/Off
To Switch the TV On
Connect the power cord to the 220-240V AC, 50 Hz. Then the standby LED lights up.
To switch on the TV from standby mode either:
Press the “ ” button, P+ / P- or a numeric button on the remote control.
Press the control switch located on the left side of the TV. The TV will then switch on.
To Switch the TV Off
Press the “ ” button on the remote control or press and hold the control switch on the TV until the TV shuts down, so the TV will switch to standby mode.
To power down the TV completely, unplug the power cord from the mains socket.
Note: When the TV is switched to standby mode, the standby LED can blink to indicate that features such as Standby Search, Over Air Download or Timer is active. The LED can also blink when you switch on the TV from standby mode.
First Time Installation
When turned on for the rst time, the “language
selection” menu appears. The message “Welcome please select your language!” is displayed and all
language options are listed alphabetically.
Press the “ ” or “ ” button to highlight the required language, press OK button to select. “First Time Installation” appears. Use “ ” or “ ” button to set the required country, and press “ ” button to select Search Type. Use “ ” or “ ” to set the desired search type. Available search types are digital and analog, digital only and analog only. When set, press “ ” to select Teletext Language. Use “ ” or “ ” button to set the “Teletext Language” and select “Scan Encrypted” using “ ” or “
” button. You can set Scan Encrypted as Yes if you
want to scan coded stations.
Press OK button on the remote control to continue and the following message will be displayed on the screen.
You must select YES to search and store broadcasts. The television will search for digital terrestrial TV broadcasts.
English - 7 -
NOTE: You can press MENU button to cancel.
After all the available stations are stored, the Channel
List will be displayed on the screen. If you are satised
with the order of channels press the OK button to quit the channel list and watch TV.
Media Playback via USB Input
You can connect a USB hard disk drive or USB memory stick to your TV by using the USB inputs of
the TV. This feature allows you to play les stored in
a USB drive. 2.5” and 3.5” inch (hdd with external power supply) external hard disk drives are supported.
IMPORTANT! You should back up your les before
making any connections to the TV set in order to avoid any possible data loss. The Manufacturer will not be
responsible for any le damage or data loss. It is
possible that certain types of USB devices (e.g. MP3 Players) or USB hard disk drives/memory sticks may not be compatible with this TV. The TV supports FAT32 and NTFS disk formatting but recording will not be available with NTFS formatted disks. Note: While formatting a USB hard disk that has 1TB (Tera Byte)
or more le capacity, you can experience problems
with the formatting process.
Quickly plugging and unplugging USB devices is a very hazardous operation. This may cause physical damage to the USB player and the USB device itself.
Do not pull out the USB module while playing a le.
Media Browser Menu
You can play photo, music, and movie les stored
on a USB disk by connecting it to your TV. Connect a USB disk to one of the USB inputs located on the side of the TV.
The USB selection OSD will be displayed on the screen. Press the MENU button and select the Media Browser tab by using the Left/Right and OK buttons. The Main media browser screen will be displayed. You can display the approprite content by selecting the Video, Music or Picture tab. Follow the button indications under each on screen menu for media playback features.
Pressing the MENU button while in the Media Browser mode will access the Picture, Sound and Settings menu options. Pressing the MENU button again will exit from this screen.
You can set your Media Browser preferences by using the Settings menu.
Note: If two USB devices are connected to the TV at
the same time, the rst USB device connected to the
TV will be named USB drive 1. Select the drive by using “ ” or “ ” buttons and press OK.
English - 8 -
Quick Menu
The Quick Settings menu allows you to access some options quickly. This menu includes Power Save Mode,
Picture Mode, Equalizer Settings, Favourites and Sleep Timer options.
Press Q.MENU button on the remote control to view the quick menu. See the following chapters for details of the listed features.
Changing Image Size: Picture Formats
Programmes can be watched in different picture formats, depending on the transmission received. You can change the aspect ratio (image size) of the TV for viewing the picture in different zoom modes. Press the “ ­SCREEN” button repeatedly to change the image size.
You can shift the screen up or down by using “ ” orbuttons while in 14:9 Zoom, Cinema or Subtitle.
Using the Channel List
Sorting Channel List
You can select which broadcasts will be listed in the
channel list. To display specic types of broadcast,
you should use the Active channel list setting. Select the Active channel list from the Channel list menu by using “ ” or “ ” button. Press the OK button to continue. You can select a network type option from the list by using “ ” or “ ” and OK buttons.
The TV sorts all stored stations in the Channel List. You can edit this channel list, set favourites or set active stations to be listed by using the Channel List options. Press the MENU button to view the main menu. Select the Channel List item by using Left or
Right button. Press OK to view menu contents. Select Edit Channel List to manage all stored channels. Use Up or Down and OK buttons to select Edit Channel List. Press the Up or Down button to select the channel that will be processed. Press the Left or Right button to select a function on the Channel List
menu. Use P+/P- buttons to move page up or down. Press MENU button to exit.
English - 9 -
Menu Features and Functions
Picture Menu Contents
Mode
Contrast Sets the lightness and darkness values of the screen.
Brightness Sets the brightness value for the screen.
Sharpness Sets the sharpness value for the objects displayed on the screen.
Colour Sets the colour value, adjusting the colors.
Power Save Mode
Backlight (optional)
Noise Reduction
Dynamic Contrast
Colour Temp Sets the desired colour tone.
Picture Zoom Sets the picture size to Auto,16:9, Subtitle,14:9, 14:9 Zoom, 4:3 or Cinema.
Movie Sense
HDMI True Black
Film Mode
Skin Tone Adjust the desired skin tone.
Colour Shift Adjust the desired colour tone.
RGB Gain
Reset Resets the picture settings to factory default settings.
Autoposition (in PC mode)
H Position (in PC mode)
V Position (in PC mode)
You can change the picture mode to suit your preference or requirements. The Picture mode can be set to one of these options: Cinema, Game, Sport, Dynamic and Natural.
To set the Power Save Mode as Eco, Picture Off and Disabled. See the section, “Environmental Information” in this manual for further information on the Power Save Mode.
This setting controls the backlight level and it can be set to Auto, Maximum, Minimum or Eco Mode. The Backlight function will be inactive if the Power Save Mode is set to
On. The Backlight cannot be activated in VGA, Media Browser mode or while the picture mode is set to Game.
If the broadcast signal is weak and the picture is noisy, use the Noise Reduction setting to reduce the amount of noise. Noise Reduction can be set to one of these options: Low, Medium, High or Off.
Advanced Settings
You can change the contrast rate by using the dynamic contrast function. Dynamic contrast can be set to one of these options: Low, Medium, High or Off.
Movie Sense: Press Use “Left” / “Right” to set Movie Sense Low, Med, High or Off. While Movie Sense is active, it will optimize the TV’s video settings for motional images to acquire a better quality and readability.
When Movie Sense option is set to Low, Med or High, Movie Sense demo option will be available. If one of these options is selected and if you press OK button, then the demo mode starts. While demo mode is active, the screen will be divided into two sections, one displaying the movie sense activity, the other displaying the normal settings for TV screen.
While watching from a HDMI source, this feature will be visible in the Picture Settings menu. You can use this feature to enhance the blackness in the picture.
Films are recorded at a different number of frames per second to normal television programmes.
Turn this feature on when you are watching lms to see the fast motion scenes clearly.
Press OK button to edit RGB gain. You can congure the colour temperature values using the RGB Gain feature.
Automatically optimizes the display. Press OK to optimize.
This item shifts the image horizontally to the right hand side or left hand side of the screen.
This item shifts the image vertically towards the top or bottom of the screen.
English - 10 -
Menu Features and Functions
Advanced Settings
Dot Clock (in PC mode)
Phase (in PC mode)
While in VGA (PC) mode, some items in Picture menu will be unavailable. Instead, VGA mode settings will be added to the Picture Settings while in PC mode.
Volume Adjusts the volume level.
Equalizer
Balance This setting is used for emphasizing left or right speaker balance.
Headphone Sets the headphone volume.
Sound Mode
AVL
Headphone/Lineout (optional)
Dynamic Bass Enables or disables the Dynamic Bass.
Surround Sound (optional)
Digital Out Sets digital audio output type.
Dot Clock adjustments correct the interference that appear as vertical banding in dot intensive presentations like spreadsheets or paragraphs or text in smaller fonts.
Depending on the resolution and scan frequency that you input to the TV set, you may see a hazy or noisy picture on the screen. In such a case you can use this item to get a clear picture by using trial and error.
Sound Menu Contents
In the equalizer menu, the preset can be changed to Music, Movie, Speech, Flat, Classic and User. Press the MENU button to return to the previous menu. Equalizer
menu settings can be changed manually only when the Equalizer Mode is in User.
You can select Mono, Stereo, Dual I or Dual II mode, only if the selected channel supports that mode.
Automatic Volume Limiting (AVL) function sets the sound to obtain a xed output
level between programmes (For instance, volume level of advertisements tend to be louder than programmes).
When you connect an external amplier to your TV using the headphone jack, you
can select this option as Lineout. If you have connected headphones to the TV, set this option as Headphone.
Surround sound mode can be changed as On or Off.
Install and Retune Menu Contents
Automatic Channel Scan (Retune)
Manual Channel Scan
Analogue Fine Tune
First Time Installation
Clear Service List
Digital Aerial: Searches and stores aerial DVB stations.
This feature can be used for direct broadcast entry.
You can use this setting for ne tuning analogue channels. This feature is not
available if no analogue channels are stored.
Deletes all stored channels and settings, resets TV to factory settings and starts
rst time installation. You can follow the instructions in the First Time Installations
section for more information on this process.
(*) This setting is visible only when the Country option is set to Denmark, Sweden, Norway or Finland. Use this setting to clear channels stored.
English - 11 -
Menu Features and Functions
Settings Menu Contents
Conditional Access Controls conditional access modules when available.
Language Congures language settings.
Parental Congures parental settings.
Timers Sets timers for selected programmes. (USB Record)
Recording
Conguration
Date/Time Sets date and time.
Sources Enables or disables selected source options.
Network Settings Displays network settings.
Menu Timeout Changes timeout duration for menu screens.
Scan Encrypted
Blue Background Activates or deactivates the blue background system when the signal is weak or absent.
Software Upgrade
Application Version Displays application version.
Hard of Hearing Enables any special feature sent from the broadcaster.
Audio Description
Auto TV Off
Standby Search (optional)
DLNA Renderer
Power Up Mode
Virtual Remote (Optional)
Displays the recording conguration menu.
Other Settings: Displays other setting options of the TV set:
When this setting is on, the search process will locate encrypted channels as well. If it is set as Off, encrypted channels will not be located in automatic or manual searches.
To ensure that your TV always has the most up to date rmware. Please ensure
that the TV is set to standby mode with an aerial connected to pick up the over air download.
Audio description refers to an additional narration track for blind and visually impaired viewers of visual media, including television and movies. You can use this feature, only if the broadcaster supports the additional narration track.
You can set the timeout value of the auto off feature. After the timeout value is reached and the TV has not been operated for a selected time, the TV will go into standby mode.
If you change Standby Search to Off, this function will be unavailable. To use Standby search please make sure that you select Standby Search as On. If the Standby Search is set to On, when the TV is in standby mode, available broadcasts will be searched. If the TV locates any new or missing broadcasts, a menu screen will be displayed, asking you whether or not to execute these changes. The Channel list will be updated and changed after this process. Please activate the Standby Search setting in order to enable your TV to automatically update the broadcast frequency
of the broadcaster, broadcast denition and other similar changes.
DLNA feature allows you to share les stored on your smartphone. If you have a
DLNA compatible smartphone and the appropriate software is installed, you can play photos on your TV. See instructions of your sharing software for more information.
Standby: The TV powers up into Standby mode when the TV is plugged into the mains.
Last State: The TV powers up into On mode when the TV is plugged into the mains and the last channel/source is selected.
Enable or disable the virtual remote feature.
English - 12 -
Electronic Programme Guide (EPG)
Some, but not all channels send information about the current and next programmes. Press the “ - EPG” button to view the EPG menu.
Up/Down/Left/Right: Navigate EPG.
OK: Displays programme options.
INF(İ): Displays, in detail, information on the programme selected.
GREEN: Switches to List Schedule EPG.
YELLOW: Switches to Timeline Schedule EPG.
BLUE: displays ltering options.
(RECORD): the TV will start to record the selected
progamme. You can press again to stop the recording.
IMPORTANT: To record a programme, you should first connect a USB disk to your TV while the TV is switched off. You should then switch on the TV to enable the recording feature. Otherwise, the recording feature will not be available.
Note: Switching to a different broadcast or source is not available during a recording.
Programme Options
In the EPG menu, press the OK button to enter the
Event Options menu.
Select Channel
In the EPG menu, using this option, you can switch to the selected channel.
Record / Delete Record Timer
After you have selected a programme in the EPG menu, press the OK button and the Options screen will be displayed. Select the “Record” option and press the OK button. After this operation, a recording will be sheduled for the selected programme.
To cancel an already set recording, highlight that programme and press the OK button and select the option “Delete Rec. Timer”. The recording will be cancelled.
Set Timer / Delete Timer
After you have selected a programme in the EPG menu, press the OK button and the Options screen will be displayed. Select the “Set Timer on Event” option and press the OK button. You can set a timer for future programmes. To cancel an already set timer, highlight that programme and press the OK button. Then select “Delete Timer” option. The timer will be cancelled.
Note: It is not possible to record two channels at the same time.
Recording a Programme
IMPORTANT: When using a new USB hard disk drive, it is
recommended that you rst format the disk using your TV’s
“Format Disk” option.
To record a programme, you should rst connect a
USB disk to your TV while the TV is switched off. You should then switch on the TV to enable the recording feature.
To use the recording function, you need to connect a USB disk or an external hard disk drive to the TV and the connected USB disk should have at least 1GB capacity and should have 2.0 speed compatibility. If the connected USB device does not support 2.0 speed, an error message will be displayed.
Note: Recorded programmes are saved into the connected USB disk. If desired, you can store/copy recordings onto a
computer; however, these les will not be available to be
played on a computer. You can play the recordings only via your TV.
Note: Lip Sync delay may occur during the timeshifting.
Radio recording is not supported. The TV can record programmes up to ten hours.
Recorded programmes are split into 4GB partitions.
If the writing speed of the connected USB disk is not
sufcient, the recording may fail and the timeshifting
feature may not be available.
Recordings of HD programmes can occupy more space on the USB disk compared to SD programmes. For this reason it is recommended to use a USB hard disk drive to record HD programmes.
Do not unplug the USB/HDD during a recording. This may harm the connected USB/HDD.
Multipartiton support is available. A maximum of two different partitions are supported. If the disk has more than two partitions, a crash may occur. The
rst partition of the USB disk is used for PVR ready
features. It also must be formatted as the primary partition to be used for the PVR ready features.
Some stream packets may not be recorded because of signal problems, so sometimes the video may freeze during playback.
English - 13 -
Record, Play, Pause, Display (for PlayListDialog) keys can not be used when teletext is ON. If a recording starts from the timer when teletext is ON, teletext is automatically turned off. Also teletext usage is disabled when there is an ongoing recording or playback.
Timeshift Recording
Press (PAUSE) button while watching a broadcast to activate timeshifting mode. In timeshifting mode, the programme is paused and simultaneously recorded to the connected USB disk. Press (PLAY) button again to resume the paused programme from where you stopped. You will see the timeshift gap between the real and the timeshifted programme in the info bar.
Instant Recording
Press (RECORD) button to start recording an event instantly while watching a programme. You can press (RECORD) button on the remote control again to record the next event on the EPG. In this case, the OSD will display the programmed events for recording. Press (STOP) button to cancel instant recording.
Note: You can not switch broadcasts or view the Media Browser during the recording mode.
Watching Recorded Programmes
In the main menu, use “ ” or “ ” buttons to select the Media Browser. Highlight the Recordings Library using “ ” or “ ” button and press the OK button to enter the Recordings Library. Select a recorded item from the list (if previously recorded) by using “ ” or “ ” buttons. Press the OK button to view the Play Options. Select an option by using “ ” or “ ” or OK buttons.
Press the (STOP) button to stop a playback and return to the Recordings Library.
Slow Forward
If you press (PAUSE) button while watching recorded programmes, the slow forward feature will be available. You can use button to slow forward. Pressing button consecutively will change slow forwarding speed.
Recordings Library
To view the list of recordings, select “Recordings Library” and press the OK button. The Recordings
Library will then be displayed with available recordings. All the recordings are kept in a list in the recordings library.
RED button (Delete) :Erases the selected recording.
GREEN button (Edit): Makes changes on the
selected recording.
BLUE button (Sort): Changes the order of the recordings. You can select from a wide range of sorting options.
OK button: Activates the play options menu:
: Resume Playback.
INFO (Details): Displays the programme information details.
RecordingConguration
Select the Recording Configuration item in the
Settings menu to congure the recording settings.
Format Disk: You can use the Format Disk feature for formatting the connected USB disk. IMPORTANT: Note that ALL the data stored on the USB disk will be lost and the disk format will be converted to FAT32 if you activate this feature. If your USB disk malfunctions, you can try formatting the USB disk. In most cases formatting the USB disk will restore normal operation; however, ALL the data stored on the USB disk will be lost in such a case.
Note: If “USB is too slow” message is displayed on the screen while starting a recording, try restarting the recording. If you still get the same error, it is possible that your USB disk does not meet the speed requirements. Try connecting another USB disk.
Available playback options:
Play from start: Plays the recording from the beginning.
Resume: Resumes Playback from the point at which you stopped playback previously.
• Play from offset: Species a playing point.
Note: Viewing main menu and menu items will not be available during the playback.
English - 14 -
Product Safety
Do not drop objects on the product or knock the product forcefully. This may result in an electric
shock or re.
• Do not use your product near a humidier or kitchen counter. This may result in an electric shock or re.
Do not disassemble, repair or modify the product
or its parts. Doing so may result in damage to the product or a malfunction.
Do not spray cleaner directly onto the surface of the product.This may result in discoloration and cracks and may cause the screen display to peel off.
Do not let water come into contact with the product when cleaning it. Ensure that water does not enter the product. This may result in an electric shock
or re.
Since the surface of the product is easily scratched,
make sure you clean the product with a soft cloth. As the product may be scratched if there is any foreign material on the cloth, make sure to shake off any dust before using it.
Do not scratch the surface of the display screen with a sharp tool or clean it using chemicals. This may degrade the screen quality.
Do not apply force to the display screen.
Do not drop or bend the product.
PC/HDD/Media Player or any other devices that are
DLNA 1.5 compatible should be used with a wired connection for higher playback quality.
Tocongure wiredsettings pleaserefer tothe
Network Settings section in the Settings menu.
You might be able to connect your TV to your LAN
depending on your network’s conguration. In such
a case, use an ethernet cable to connect your TV directly to the network wall outlet.
The modem port on the wall
Rear of TV
Wired Connectivity
To Connect to a Wired Network
For connecting to a wired LAN, you should perform the following steps:
You must have a modem/router connected to an active broadband connection.
Ensure that Nero Media Home software is installed to your PC (for DLNA function). See Appendix G for more information on the installation process.
Connect your PC to your modem/router. This can be a wired or wireless connection.
Connect your TV to your modem/router via an ethernet cable. There is a LAN port at the rear (back) of your TV.
Broadband ISP Connection
Lan(Ethernet cable)
Rear of TV
• To access and play shared les, you must select the
Media Browser. Press the Menu button and select Media Browser by using the “ ” or “ ” buttons and press OK to continue. Select the desired le type and press OK. You must always use the Media Browser
screen to access and play shared network les.
ConguringWiredDeviceSettings
The Network type can be selected as Wired or Wireless, in accordance with the active connection to the TV set. Select this as “Wired” if you are connecting via an ethernet.
CongurationStatus
This section displays the status of the connection. Select Connected if you want to activate a connection. Select as Not Connected to end an active connection.
IP Address
If an active connection is available, the IP address will
be displayed on this section. If you want to congure
an IP address preference, press the GREEN button and switch to the advanced mode.
ConguringWiredNetworkSettingsin
Advanced Mode
After pressing the GREEN button, the “Advanced mode” will be available. While in Advanced Mode, press the RED button to edit settings. When nished, press OK to save, Press RETURN/BACK to cancel
English - 15 -
Wireless Connectivity
Connecting to a Wireless Network
IMPORTANT: USB dongle (supplied) is required to
use wireless network features.
To use your TV with your wireless network, you need a Wireless USB dongle. To make your modem’ s SSID visible, you should change your SSID settings via the modem’s software. The TV cannot connect to the networks with a hidden SSID.
To Connect to a wireless LAN, you should perform the following steps:
1. Ensure that Nero Media Home software is
installed to your PC (for DLNA function).
2. Then connect the wireless adaptor to one of the
USB inputs of the TV.
3. To congure your wireless settings please refer to
Network settings section in this manual.
Broadband ISP Connection
USB Inputs (Side of the TV)
The location where the transmission is most effective differs depending on the usage environment.
The Wireless LAN adaptor should be connected directly to the TV’s USB port. USB hubs are not supported.
• To congure wireless settings please refer to the
WiFi section in the Settings menu.
Wireless LAN adaptor supports 802.11 a,b,g & n type modems. It is highly recommended that you should use the IEEE 802.11n communication protocol in order to avoid any possible problems while watching videos.
Use the other USB input, if you experience problems with audio/video performance.
You must change your modem’s SSID when there are any other modems around with the same SSID. You can encounter connection problems otherwise. Use a wired connection if you experience problems with a wireless connection.
Wireless Lan Adaptor
A Wireless-N router (IEEE 802.11a/b/g/n) with simultaneous 2.4 and 5 GHz bands is designed to increase bandwidth. These are optimized for smoother and faster HD video streaming, file transfers, and wireless gaming.
Use a LAN connection for quicker file sharing between other devices like computers.
The frequency and channel differ depending on the area.
The transmission speed differs depending on the distance and number of obstructions between the
transmission products, the conguration of these products, the radio wave conditions, the line trafc,
and the products that you use. The transmission may also be cut off or may get disconnected depending on the radio wave conditions, DECT phones, or any other WiFi 11b appliances. The standard values of the transmission speed are the theoretical maximum values for the wireless standards. They are not the actual speeds of data transmission.
English - 16 -
To enable Wi-Fi features, plug in the Wi-Fi dongle to one of the USB ports.
Press the YELLOW button to scan the wireless networks from the network settings menu. A list of available networks will be displayed. Please select your desired network from the list.
Note: If the modem supports N mode, you should set N mode settings.
If the selected network is protected with a password, please enter the correct key by using the virtual keyboard. You can use this keyboard via the navigation buttons (“ ” or “ ”, “ ” or “ ”) and the OK button on the remote control.
Wait until the IP address is shown on the screen.
Press the GREEN button to switch to advanced mode and then press the OK button to edit settings. This means that the connection is now established.
To disconnect from a wireless network, you should highlight CongurationStatus and press OK.
You can navigate between menu tabs by pressing left/right buttons. The help bar on the bottom of the dialog shows features that you may use. Press the BLUE button to check your internet connection speed.
You can check the signal strength by using the network settings menu for the wireless device mode.
Other Information
Configuration Status: Displays Wi-Fi status as
connected or not connected.
IP Address: Displays the current IP address.
Network Name: Connected networks’ name will be
displayed.
DeleteSavedWiFiProles
Saved proles will be deleted if you press the Red
button while the wireless device selection OSD is on the screen.
Connecting to your mobile Phone via WiFi
If your mobile phone has WiFi feature, you can connect your mobile phone to your TV by using a WiFi connection via a router, in order to play content from your phone. For this, your cell phone must have appropriate sharing software.
Connect to your router following the steps stated
above in the Wireless Connection section.
Afterwards, engage your cell phone with the router
and then activate the sharing software on your cell
phone. Then, select les that you would like to share
with your TV.
If the connection is established correctly, you should
now be able to access the shared les from your cell
phone via the Media Browser of your TV.
Enter the Media Browser menu and the playback
device selection OSD will be displayed. Select your mobile phone and press the OK button to continue.
Note: This feature may not be supported on all mobile phones.
Connectivity Troubleshooting
Wireless Network Not Available
Ensure that any rewalls of your network allow
the TV wireless connection.
Ensure the USB WiFi dongle (supplied) is plugged in fully.
If the wireless network does not function properly, try using the wired network in your home. Refer to the Wired Connection section for more information on the process.
If the TV does not function using the wired connection, check the modem (router). If the router does not have a problem, check the internet connection of your modem.
Try searching for wireless networks again, using the Network Settings menu screen.
Connection is slow
See the instruction book of your wireless modem to get information on the internal service area, connection speed, signal quality and other settings. You need to have a high speed connection for your modem.
Distruption during playback or slow reactions
You could try the following in such a case:
Keep at least three meters distance from microwave ovens, mobile telephones, bluetooth devices or any other Wi-Fi compatible devices. Try changing the active channel on the WLAN router.
Using DLNA Network Service
DLNA (Digital Living Network Alliance) is a standard that eases the viewing process of digital electronics and makes them more convenient to use on a home network. For further information, visit www.dlna.org.
The DLNA standard allows you to view and play photos, music and videos stored in the DLNA media server connected to your home network.
1. Nero Media Home Installation
The DLNA function cannot be used if the server program is not installed on to your PC. Please prepare your PC with the provided Nero Media Home programme. For more information about the
installation, please refer to appendix A.
2. Connect to a Wired or Wireless Network
See the chapter Network Settings for detailed
conguration information.
3. Play Shared Files via Media Browser
Select Media Browser by using the “ ” or “ ” buttons from the main menu and press OK. The Media browser will then be displayed.
English - 17 -
DLNA
DLNA support is only available in the Media Browser folder mode. To enable folder mode, go to the Settings tab in the main media browser screen and press OK. In the settings options, highlight View Style and change to Folder using the “ ” or “ ” buttons. Select the desired media type and press OK.
If sharing congurations are set properly, the following
OSD message will be displayed after selecting the desired media type. Select OK to display the selected network or USB memory content. If you want to refresh the device list, press the GREEN button. You can press MENU to exit.
If available networks are found, they will be listed on this screen. Select media server or network that you want to connect to using the “ ” or “ ” buttons and press OK.
If you select the media type as Video and choose a device from the selection menu, a new menu screen will appear on the screen as below:
To play other media types from this screen, you must go back to main Media Browser screen and select the media type as desired and then perform the network selection again. Refer to the Media Browser
USB Playback section for further information on le
playback.
Subtitle les do not work if you watch videos from your
network through DLNA.
You can connect only one television with DLNA to the same network. If a problem occurs with the DLNA network, please switch your television off at the wall socket and back on again. Trick mode and jump are not supported with the DLNA function.
Note: There may be some PC’s which may not be able to utilize the DLNA function due to administrator and security settings (such as business PC’s).
For best home network streaming with this TV, the supplied Nero software should be installed.
Internet Portal
Ensure the TV is connected to a Wired/Wireless Internet connection. After the connection is established, you can select or view portal options.
Note: A Broadband Internet connection is required for high quality viewing. Ensure that the internet connection is made properly. You must set the Country and Language data correctly in the First Time Installation for the proper operation of the internet portal.
Press “ ” button on your remote control and the portal application options will be displayed. The application options will be displayed in a manner similar to the template below.
Select Videos from this screen to list all the available
video les from the selected network.
English - 18 -
Use the “ ” or “ ”, “ ” or “ ” to navigate between the items on Portal screen. Press the OK button to conrm your selection. Press the BACK button to go to the previous screen.
Press the EXIT button to quit the Internet portal mode.
iPlayer Application
You can access BBC iPlayer using your TV. To do this, an active internet connection is required. (See connecting to a Wired/Wireless Network section to connect your TV to internet). After the connection is established, you can select BBC iPlayer among the portal options. (See Internet Portal)
Press the OK button on your remote control to start the BBC iPlayer application.
Note: Broadband internet connection (minumum 2mbps) is required for high quality viewing.
Playing a Programme via iPlayer
Select a programme and press OK button. The programme playback will begin.
You can press the PAUSE button to pause playback. Press the PLAY button to resume the playback.
Use the STOP button to stop the playback.
Press the EXIT button to exit iPlayer. Press the RETURN button for going back to the previous screen.
Note: “Episode is unavailable.” message may be displayed on the screen if a problem occurs during the playback.
Searching a Programme
Highlight the Search tab using the navigation buttons and press the OK button. Use the virtual keyboard to type the letters. Select letters and press the OK
button. When nished, highlight Search option and
press the OK button.
Digital Teletext
Press the “ ” button. The digital teletext information appears. Operate it with the coloured buttons, cursor buttons and the OK button.
The operation method may differ depending on the contents of the digital teletext. Follow the instructions displayed on digital teletext screen.
When the “ ” button is pressed again, the TV returns to television broadcast.
English - 19 -
Software Upgrade
Your TV is capable of finding and updating automatically via the Aerial signal or over the Internet.
Background search and upgrade mode
While the TV is connected to the Internet, if new software is found, it downloads the upgrades automatically when the TV next powers on from standby.
3.00am search and upgrade mode
While the TV is connected to an aerial signal. If Automatic scanning in the Upgrade Options menu is enabled, the TV wakes up at 03:00 and searches broadcast channels for new software upgrades. If new software is found and downloaded successfully, the next time the TV powers up , it will have the new software version.
Note. If the TV fails to come on after the upgrade unplug the TV for 2 minutes and plug in again.
Troubleshooting & Tips
Image persistence - ghosting
Please note that ghosting may occur while displaying a persistent image (still or paused image). LCD/LED TVs’ image persistence may disappear after a short time. Try turning off the TV for a while. To avoid this, do not leave the screen in still picture mode for extended periods of time.
No power
If your TV has no power, please check the power cord plug is connected to the mains power socket.
Poor picture
1. Have you selected the correct TV system?
2. Is your TV or house aerial located too close to a
non-earthed audio equipment or neon lights, etc.?
3. Mountains or high buildings can cause double
pictures or ghost images. Sometimes you can improve the picture quality by changing the direction of the aerial. Is the picture or teletext unrecognisable?
4. Check if you have entered the correct channel
frequency if you have done manual tuning.
5. Please retune the channels.
6. The picture quality may degrade when two devices
are connected to the TV at the same time. In such a case, disconnect one of the devices.
No picture
1. No Picture means that your TV is not receiving a
transmission. Have you selected the correct button on the remote control? Try once more. Also make sure the correct input source has been selected.
2. Is the aerial connected properly?
LicenceNotications
Manufactured under license from Dolby Laboratories.
TRADEMARK ACKNOWLEDGMENT
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
“DLNA®, the DLNA Logo and DLNA CERTIFIED® are
trademarks, service marks, or certication marks of
the Digital Living Network Alliance.”
“HDMI, the HDMI logo and High-Denition Multimedia
Interface are trademarks or registered trademarks of HDMI Licensing LLC.”
English - 20 -
Appendix A: Nero MediaHome Installation
This software is compatible with Windows XP and Windows 7.
Note: To use DLNA function, this software should be installed to your PC.
To install Nero MediaHome onto your computer.
1) Insert the Nero MediaHome installation disc into your optical disc drive.
2) The Nero MultiInstaller screen will open automatically.
3) Click on the button labeled Nero MediaHome 4 Essentials to start the installation process.
Note: If the below window is not displayed automatically, double-click on the le SetupX located on the Nero
MediaHome installation disc.
4) The Nero MediaHome installation wizard is displayed. If necessary change installation language from the language selection menu before continuing.
5) Click the Next button.
The integrated serial is displayed. (Do not change the serial number)
6) Click the Next button. The License Conditions (EULA) screen is displayed.
7) Click the Next button.
The Select Installation Type screen is displayed. It is possible to choose between Typical, meaning standard
installation, or Custom installation. User dened installation allows you to determine languages to be installed
and to choose the installation path.
8) Use Typical installation and click the Next button.
The Prerequisites screen is displayed.•
The Nero MediaHome installation wizard checks the availability of required third-party software on your PC. If applications are missing they are listed and must be installed before continuing installation.
9) As soon as all prerequisites are installed, the Install button will change to a Next button.
10) Ready to Start Installation Process screen is displayed, installation begins and nishes automatically.
English - 21 -
Appendix B: PC Input Typical Display
14
45
Modes
The following table is an illustration of some of the typical video display modes. Your TV supports up to 1920x1200.
Index Resolution Frequency
1 640x350 85Hz
2 640x400 70Hz
3 640x400 85Hz
4 640x480
5 640x480
6 640x480
7 640x480
8 640x480
9 800x600
10 800x600
11 800x600
12 800x600
13 800x600
800x600
15 832x624 75Hz
16 1024x768
17 1024x768
18 1024x768
19 1024x768
20 1024x768
21 1024x768
22 1152x864
23 1152x864
24 1152x864
25 1152x864
26 1152x870
27 1280x768
28 1280x768
29 1280x768
30 1280x960
31 1280x960
32 1280x960
33 1280x1024
34 1280x1024
35 1280x1024
36 1360x768 60Hz
37 1400x1050 60Hz
38 1400x1050 75Hz
39 1400x1050 85Hz
40 1440x900 60Hz
41 1440x900 75Hz
42 1600x1200 60Hz
43 1680x1050 60Hz
44 1920x1080 60Hz
1920x1200 60Hz
60Hz
66Hz
72Hz
75Hz
85Hz
56Hz
60Hz
70Hz
72Hz
75Hz
85Hz
60Hz
66Hz
70Hz
72Hz
75Hz
85Hz
60Hz
70Hz
75Hz
85Hz
75Hz
60Hz
75Hz
85Hz
60Hz
75Hz
85Hz
60Hz
75Hz
85Hz
Appendix C: AV and HDMI Signal Compatibility (Input Signal Types)
Source
EXT-1 (SCART1)
EXT-1 (SCART2)
Side AV
YPbPr
HDMI1
HDMI2
HDMI3
HDMI4
(X: Not Available, O: Available)
In some cases a signal on the TV may not be displayed properly. The problem may be an inconsistency with standards from the source equipment (DVD, Set-top box, etc. ). If you do experience such a problem please contact your dealer and also the manufacturer of the source equipment.
Supported
Signals
PAL O
NTSC 60 O
RGB 50/60 O
SECAM O
PAL O
NTSC 60 O
SECAM O
PAL 50/60 O
NTSC 60 O
SECAM O
480I 60Hz O
480P 60Hz O
576I 50Hz O
576P 50Hz O
720P 50Hz O
720P 60Hz O
1080I 50Hz O
1080I 60Hz O
480I 60Hz O
480P 60Hz O
576I 50Hz O
576P 50Hz O
720P 50Hz O
720P 60Hz O
1080I 50Hz O
1080I 60Hz O
24Hz
25Hz
1080P
30Hz
50Hz
60Hz
Available
O
English - 22 -
Appendix D: Supported File Formats for USB Media Browser
Media Extension Format Notes
Video Audio
Movie dat, mpg,
Music .mp3
Photo .jpg .jpeg Baseline JPEG max WxH =
Subtitle
mpeg
dat, mpg, mpeg
.vob MPEG2 MPEG1/2 Layer 1/2/3, AC3, LPCM 1080P@ 30fps 50Mbit/sec
.mkv MPEG1,2,4,
.mp4 .mov MPEG1/2 Layer 3, AAC/HEAAC,
RMVB, RM rv30, rv40 LBR(cook), AAC/HEAAC 1080P@ 30fps 50Mbit/sec
avi MPEG1,2,4
v H.264,
3gp,3g2 MPEG4, H.264 1920x1080 @ 30P
asf, wmv MPEG2,4, XviD, H.264,
OGG OGG
.wav LPCM
WMA/ASF WMA, WMA Pro
.m4a/ .aac AAC, HEAAC
.png Progressive JPEG
.bmp non-interlace
.png
sub - -
srt - -
Mpeg1,2 MPEG1/2 Layer 1/2/3, AAC/HEAAC,
MPEG2 ,H.264, VC1, AVS, MVC
XviD,
H.264,
VC1,WMV3,
Motion JPEG
Xvid
H.264,
VC1,WMV3,
Sorenson H.263
Motion JPEG
Sorenson H.263
VC1,WMV3
-
AC3/EAC3, LPCM/ADPCM
MPEG1/2 Layer 1/2/3, AAC/HEAAC, AC3/EAC3, LPCM/ADPCM
MPEG1/2 Layer 1/2/3, AAC/HEAAC,
AC3/EAC3, LPCM,OGG
AC3/EAC3, LPCM/ADPCM
MPEG1/2 Layer 1/2/3, AAC/HEAAC, AC3/EAC3, LPCM/ADPCM, WMA
MPEG1/2 Layer 3, AAC/HEAAC, LPCM/ADPCM
MPEG1/2 Layer 1/2/3, AAC/HEAAC, AC3/EAC3, LPCM, WMA
MPEG1 Layer 1/2/3 (MP3)
interlace
1080P@ 30fps 50Mbit/sec
H.264:1080Px2@25fps 1080P@ 50fps MVC: 1080P@ 24fps Other: 1080P@ 30fps” 50Mbit/sec
H.264:1080Px2@25fps 1080P@ 50fps Other:1080P@ 30fps 50Mbit/ sec
H.264: 1080Px2@25fps 1080P@ 50fps Other: 1080P@ 30fps 50Mbit/sec
H.264: 1080Px2@25fps 1080P@ 50fps Other: 1080P@ 30fps” 50Mbit/ sec
H.264: 1080Px2@25fps 1080P@ 50fps Other: 1080P@ 30fps” 50Mbit/sec
20Mbit/sec
1080P@ 30fps 50Mbit/sec
14592x12288
Up to 8 MegaByte
English - 23 -
Appendix E: Supported DVI Resolutions
When connecting devices to your TV’s connectors using DVI converter cable (not supplied), you can refer to the following resolution information.
24Hz 25Hz 30Hz 50Hz 60Hz
480i
480p
576i
576p
720p
1080i
1080p
þ
þ
þ þ
þ þ
þ þ þ þ þ
þ
þ
SKY Remote Control Code
The Sky Code is 065:
1 Turn your TV on.
2 Press TV on your Sky remote control handset.
3 Hold down SELECT and the RED button together for about two seconds, until the red light on the Sky remote control blinks twice.
4 Key in 065. The light on the Sky remote control should blink twice.
5 Press the STANDBY button on your Sky remote control. If your TV switches off, press SELECT. The light on the Sky remote control blinks twice. Now try the other functions.
Specications
RF AERIAL INPUT 75 Ohm (unbalanced)
OPERATING VOLTAGE 220-240V AC, 50 Hz.
AUDIO OUTPUT POWER (W
POWER CONSUMPTION (W)
165 W (max)
PANEL
16:9 display, 55” Screen Size
DxLxH (With foot): 221 x 1282 x 791
Weight (Kg): 25
DxLxH (Without foot): 40 x 1282 x 753
Weight (Kg): 20.40
Transmission Standards:
VHF (BAND I/III) UHF (BAND U) HYPERBAND
DVB-T, MPEG2,DVB-T, MPEG4 HD, DVB-T2
) (10% THD) 2 x 12
RMS.
English - 24 -
50229970
Loading...