PF SERIES PUMPS
PFM, PFP, PFV
OPERATION, INSTALLATION & PARTS MANUAL
EU Declaration of Conformity
Finish Thompson Inc. hereby declares that the following machine(s) fully comply with the
applicable health and safety requirements as specified by the EU Directives listed. The product may
not be taken into service until it has been established that the drive motor for the Drum and
Container Pump complies with the provisions of all relevant EU Directives. The complete product
complies with the provisions of the EU Directive on machinery safety provided motors
manufactured by Finish Thompson Inc. are used.
This declaration is valid provided that the devices are fully assembled and no modifications are
made to these devices.
Type of
Device:
Drum and Container Pump
Tubes
Models:
EU
Directives:
Machinery Safety
(2006/42/EC)
Applied Harmonized
Standards:
EN ISO 12100
EN
809
Manufacturer:
Finish
Thompson
Inc.
921 Greengarden
Road
Erie, Pennsylvania 16501-1591
U.S.A
Signed,
_
President
1 August 2016
Person(s) Authorized to Compile Technical File: Finish Thompson GmbH
Otto-Hahn-Strasse 16
Maintal, D-63477 DEU
Telephone: 49 (0)6181-90878-0
BTS – 40
EPPI/EPPS 15/27/40
EFP/EFV/EFS-16/27/40/48/54
HVDP LR-27/40/48
HVDP HR-27/40/28
PFM-27/40/48/60
PFP-15/27/40/48/60/72
PFS-27/40/48/60/72
PFV-27/40/48/60/72
TBP-27/40/48
TBS-40
TTC/TTS-27/40/48
STTS-40
TMS-40
2
Introduction
This manual pertains to the PF Series, specifically the PFP, PFM, and PFV plastic drum pumps. Finish Thompson Inc.
thanks you for choosing our products. We believe the use of our products will be fully satisfactory. When properly
installed and operated, your Finish Thompson motor and pump will provide long, trouble-free service; therefore,
please read this manual carefully before carrying out any operations on the pump/motor unit. Any use other than that
described herein is considered incorrect; and, consequently, Finish Thompson Inc. shall not be held responsible for
any damages to people or property. In case of doubt or enquiries, please reply to our Technical Service department
directly at the following address:
Finish Thompson, Inc.
921 Greengarden Rd.
Erie, PA 16501 U.S.A.
Tel. 1-814-455-4478; Fax 1-814-455-8518
www.finishthompson.com; fti@finishthompson.com
Index
Introduction ............................................................................................................................. 3
Warranty, General Terms & Conditions ......................................................................................4
Safety ...................................................................................................................................... 5
Important Safety Information for Pumping Flammable or Hazardous Substances ...................... 6
Pump Specifications ................................................................................................................ 7
Installation ............................................................................................................................... 8
Operation ................................................................................................................................. 8
Maintenance
Disassembly ....................................................................................................................... 8
Inspection ........................................................................................................................... 9
Reassembly ........................................................................................................................ 9
Exploded View ......................................................................................................................... 10
Pump Tube Spare Parts List .....................................................................................................11
Technical Service Hotlne: 1-800-888-3743 or email techservice@finishthompson.com
3
Warranty, General Terms & Conditions
1. The following terms and conditions apply to the sale of machinery, components and related services and products, of Finish
Thompson Inc. (hereinafter “the products”)
2. Finish Thompson Inc. (the manufacturer) warrants only that:
a) its products are free of defects in material, design and workmanship at the time of original purchase;
b) its products will function in accordance with Finish Thompson Inc. operation manuals; Finish Thompson Inc. does not
guarantee that the product will meet the precise needs of the Customer, except for those purposes set out in any invitation
to render documents or other documents specifically made available to Finish Thompson Inc. before entering into this
agreement;
c) high quality materials are used in the construction of the pumps and that machining and assembly are carried out to the
highest standards. Except as expressly stated above, Finish Thompson Inc. makes no warranties, express or implied,
concerning the products, including all warranties of fitness for a particular purpose.
This warranty shall not be applicable in circumstances other than defects in material, design, and workmanship. In particular
warranty shall not cover the following:
d) Periodic checks, maintenance, repair and replacement of parts due to normal wear and tear;
e) Damage to the product resulting from:
i. Tampering with, abuse or misuse, including but not limited to failure to use the product for its normal purposes as
stated at the time of purchase or in accordance with Finish Thompson, Inc. instructions for use and maintenance of the
product, or the installation or improper ventilation or use of the product in a manner inconsistent with the technical or
safety standard in force;
ii. Repairs performed by non-authorized service workshop, or opening of the unit by non-authorized personnel, or use of
non genuine Finish Thompson Inc. parts;
iii. Accidents, force majeure or any cause beyond the control of Finish Thompson Inc., including but not limited to light ning, water, fire, earthquake, and public disturbances, etc.
3. The warranty shall cover the replacement or repair of any part, which is documented to be faulty due to construction or as sembling, with new or repaired parts free of charge delivered by Finish Thompson, Inc. Parts subjected to normal wear and
tear shall not be covered by the warranty. Finish Thompson, Inc. shall decide as to whether the defective or faulty part shall be
replaced or repaired. Transportation charges are prepaid to Finish Thompson.
4. The warranty of the products shall be valid for a period of 12 months from the date of delivery, under the condition that notice
of the alleged defect to the products or parts thereof be given to Finish Thompson, Inc. within the term of 8 days from the
discovery.
5. Repair or replacement under the terms of this warranty shall not give a right to an extension to, or a new commencement of,
the period of warranty. Repair or replacement under the terms of this warranty may be fulfilled with functionally equivalent re conditioned units. Finish Thompson Inc. qualified personnel shall be solely entitled to carry out repair or replacement of faulty
parts after careful examination of the motor. Faulty parts or components when replaced by Finish Thompson Inc. will become
the property of Finish Thompson Inc. If this warranty does not apply, the purchaser shall bear all cost for labor, material and
transportation.
6. Finish Thompson Inc. will not be liable on any claim, whether in contact, tort, or otherwise, for any indirect, special, incidental,
or consequential damages, caused to the customer or to third parties, including loss of profits, process down time, transpor tation costs, costs associated with replacement or substitution products, labor costs, installation or removal costs. In any and
all events, manufacturer’s liability shall not exceed the purchase price of the product and/or accessories.
7. Return Policy. Should you have any problems with this product, please contact the distributor in your area. The distributor
will determine if a return to the factory is necessary and will contact the factory for a Return Authorization Number. Otherwise,
contact our Technical Service Hotline (1-800-888-3743) or e-mail techservice@finishthompson.com if you have any questions
regarding product operation or repair.
Warranty Registration
Thank you for your purchase of this quality Finish Thompson product. Be sure to take a minute to register your pump at
Finishthompson.com/warranty. Simply provide the model number, serial number and a few other pieces of information.
4
Safety
1. Introduction
This manual contains all the information needed for the correct installation, use and maintenance of your new Finish Thompson
pump. It should be read and understood by all the personnel involved in installation, operating and servicing of the pump before
it is started.
2. Operator Qualification and Training
The personnel in charge of the installation, the operation, and the maintenance of the pump must be qualified and able to per form the operations described in this manual. Finish Thompson, Inc. shall not be held responsible for the training level of
personnel and for the fact that they are not fully aware of the contents of this manual.
3. Safety Instructions
FOR YOUR OWN SAFETY
BEFORE using or servicing your pump, please make sure to wear the proper clothing, eye protection and follow standard safety
procedures when handling corrosive or personally harmful materials.
ALWAYS use and store the pump and motor in an upright position.
DANGER: POWER SUPPLY
Refer to instructions in the appropriate motor Operation & Installation Manual.
4. Noise Level
Refer to specifications in the appropriate motor Operation & Installation Manual.
5. Modifications and Spare Parts
Any changes concerning the service of the pump as originally purchased can be executed only after written approval from
Finish Thompson Inc. It is recommended to use only genuine Finish Thompson Inc. spare parts and approved accessories. The
use of non-original spare parts or non-approved accessories will void warranty and removes any responsibility on the manufac turer’s behalf for any damage caused to people or things.
6. Cleaning
It is highly recommended to flush pumps with clean water or some other neutralizing fluid compatible with pump materials
when done pumping or when switching chemicals.
5
IMPORTANT SAFETY INFORMATION FOR PUMPING FLAMMABLE OR HAZARDOUS SUBSTANCES
Read these instructions before operating the pump and motor equipment. The manufacturer will not be responsible for any damage to property or to persons
caused by improper use of the equipment.
WARNING: It is the responsibility of the user to operate the pump in conformance with OSHA rules for dispensing liquids. Pump containers should be
grounded when using with flammable or combustible liquids to avoid static electricity.
1. Use only an explosion-proof rated electric or non-electric (air) motors on stainless steel pump tubes with a Static Protection Kit when transferring flammable
or combustible liquids.
WARNING: Never use an open, splash-proof, TEFC, battery-operated or non-explosion-proof rated motor or a plastic pump tube when transferring flammable
or combustible liquids.
2. When operating a drum pump (especially when pumping flammable, combustible or hazardous liquids) follow all electrical and safety codes.
a) In the United States: the United States Occupational Safety and Health Act (OSHA), most recent National Electrical Code (NEC), National Fire
Protection, Inc. (NFPA) Code 30 (Flammable and Combustible Code), NFPA 77 (Static Electricity), NFPA 251 (Standard Method of fire Test of Building
Construction), NFPA 704 (Identification of the Fire Hazards of Materials), and other NFPA codes, local codes and ordinances.
b) Outside the United States: the ATEX equipment directive 2014/34/EU where applicable, the ATEX workplace 99/92/EC directive where applicable, in
addition the precautions of the U.S. codes listed herein and all other local codes and ordinances.
3. Pumping hazardous, flammable, or combustible liquids should only be done in buildings, rooms, or areas suited for this purpose. (See NFPA 30, NFPA 78,
NFPA 80, NFPA 251, NFPA 704, other suitable NFPA codes, OSHA, ATEX workplace 99/92/EC directive insurance companies, and other local codes and ordinances.)
4. When filling cans, drums, etc. with combustible or flammable liquids, both container pumping from and container pumping to, should be bonded and
grounded to dissipate possible accumulations of static electricity, and minimize sparks caused by static electricity (refer to NFPA 77 and CLC/TR 60079-32-1
for specific details).
WARNING: Avoid splashing. Splash filling can create static electricity and is extremely hazardous. Reduce motor speed to prevent splashing.
WARNING: Fluid velocity must be 3 feet/.9 meter/second maximum (7 gpm/26.5 lpm in 1” hose and 4 gpm/15 lpm in ¾” hose) to reduce risk of static elec-
tricity. Reduce motor speed to reduce the fluid velocity.
5. Before using, confirm that the pump and any accessories (hose, nozzle, flow meter, etc.) materials of construction are suitable for the material to be pumped
and that the maximum temperature is not exceeded.
INFORMATIONS IMPORTANTES SUR LA SÉCURITÉ DURANT LE POMPAGE DE SUBSTANCES INFLAMMABLES OU DANGEREUSES
Veuillez lire attentivement ces instructions avant d’utiliser la pompe et l’équipement du moteur. Le fabricant ne sera pas tenu responsable des dommages matériels ou corporels causés par une utilisation inappropriée de l’équipement.
AVERTISSEMENT: Il est de la responsabilité de l’utilisateur de faire fonctionner la pompe conformément aux règles OSHA (Santé et Sécurité au Travail)
relatives à la distribution de liquides. Les conteneurs de pompes doivent être électriquement mis à la terre lors de l’utilisation de liquides inflammables ou
combustibles afin d’éviter toute électricité statique.
1. Lors du transfert de liquides inflammables ou combustibles, utilisez uniquement des moteurs électriques ou non électriques (pneumatiques) antidéflagrants
sur des tubes de pompe en acier inoxydable dotés d’un dispositif de protection antistatique.
AVERTISSEMENT: N’utilisez jamais de moteur ouvert, à l’épreuve des éclaboussures, TEFC, alimenté par piles ou non antidéflagrant, ni un tube de pompe en
plastique lors du transfert de liquides inflammables ou combustibles.
2. Lors de l’utilisation d’une pompe à tambour (en particulier lors du pompage de liquides inflammables, combustibles ou dangereux), respectez tous les codes
électriques et les codes de sécurité.
a) Aux États-Unis : Loi américaine sur la sécurité et la santé au travail (OSHA); le code national de l’électricité (NEC) le plus récent; le code 30 de la
NFPA (code d’inflammabilité et de produits combustibles); le code NFPA 77 (électricité statique); le code NFPA 251 (Méthode standard de test
d’incendie de la construction de bâtiments); le code NFPA 704 (Identification des risques d’incendie des matériaux) et autres codes et règlements de
la NFPA.
b) En dehors des États-Unis : La directive sur les équipements ATEX 2014/34 / EU, le cas échéant, la directive ATEX sur le lieu de travail 99/92 /EC, le
cas échéant, ainsi que les précautions des codes des États-Unis énumérés dans la présente et de tous les autres codes, lois et règlements locaux.
3. Le pompage de liquides dangereux, inflammables ou combustibles ne doit être effectué que dans des bâtiments, des pièces ou des zones adaptées à cet
usage. (Voir NFPA 30, NFPA 78, NFPA 80, NFPA 251, NFPA 704, autres codes NFPA appropriés, OSHA, les directives des compagnies d’assurance ATEX 99/92
/CE, et autres codes, lois et règlements locaux.)
4. Lors du remplissage de bidons, fûts, etc. avec des liquides combustibles ou inflammables, les conteneurs d’où le liquide est pompé et le conteneur
recevant le liquide doivent être reliés et mis à la terre pour éviter toute accumulation éventuelle d’électricité statique et minimiser ainsi les étincelles
causées par l’électricité statique (voir NFPA 77). et CLC / TR 60079-32-1 pour des détails spécifiques).
AVERTISSEMENT: Évitez les éclaboussures. Les éclaboussures peuvent créer de l’électricité statique et sont extrêmement dangereuses. Réduisez la vitesse
du moteur pour éviter les éclaboussures.
AVERTISSEMENT: La vitesse du fluide doit être au maximum de 3 pieds / 0,9 mètre / seconde (7 gpm / 26,5 lpm dans un tuyau de 1”; et 4 gpm / 15 lpm
dans un tuyau de ¾”) afin de réduire le risque d’électricité statique. Réduisez la vitesse du moteur afin de réduire ainsi la vitesse du fluide.
5. Avant utilisation, assurez-vous que les matériaux de la pompe et des accessoires (tuyau, ajutage, débitmètre, etc.) sont compatibles avec le
fluide et que la température maximale n’est pas dépassée.
6
PUMP SPECIFICATIONS
Outer Tube Diameter 2” (51 mm) 2” (51 mm) 2” (51 mm)
Discharge Spout 1” Variable orifice barb fitting 1” Variable orifice barb fitting 1” Variable orifice barb fitting
Discharge Thread 1-1/4” NPSM 1-1/4” NPSM 1-1/4” NPSM
Max. Specific Gravity 1.83 1.83 1.83
Max. Viscosity 2000 cP 2000 cP 2000 cP
Min./ Max. Fluid
Temperature
35°F Minimum to 160°F Maximum 35°F Minimum to 160°F Maximum 35°F Mininum to 120°F Maximum*
(1.6°C Minimum to 71°C Maximum) (1.6°C Minimum to 71°C Maximum) (1.6°C Minimum to 49°C Maximum)
Wetted Materials Polypro, FKM, PTFE, ETFE, 316 SS Polypro, FKM, PTFE, ETFE, Alloy 625 (PFP) Unfilled Polypro, PVDF, FKM, PTFE, ETFE, Alloy 625
MODEL PFM MODEL PFP MODEL PFV
*PFV-72: 35°F Min. to 115°F Max. (2°C Min. to 49°C Max.)
MODEL
DIM ‘A’
(IN.)
DIM ‘A’
(MM)
DIM ‘B’
(IN.)
DIM ‘B’
(MM)
DIM ‘C’
(IN.)
DIM ‘C’
(MM)
PFM/PFP/PVF-27 27 686 29 737 38-29/32 988
PFM/PFP/PVF-40 40 1016 42 1067 51-29/32 1318
PFM/PFP/PVF-48 48 1219 50 1270 59-29/32 1522
PFM/PFP/PVF-54 54 1372 56 1422 65-29/32 1674
PFM/PFP/PVF-60 60 1524 62 1575 71-29/32 1826
PFM/PFP/PVF-72 72 1829 74 1880 83-29/32 2131
7
INSTALLATION & MAINTENANCE INSTRUCTIONS
Installation
1. Remove the drum pump from its packaging and inspect for shipping damage.
2. Turn the pump coupling to verify there is no binding.
3. Verify the housing cover (item 16) is on tight (it has a left hand thread).
4. Adjust the coupling so that the empty slots in the insert are at 3 and 9 o’clock with the pump dis-
charge at 12 o’clock.
5. Install the motor onto the drum pump per the installation instructions from the Operation & Installation
Manual of the specific motor model.
Note: Pumps with the standard 1” barb spout include a variable orifice fitting, which initially limits the flow of the
pump to 10 gpm. As it is cut away, flow will increase from 10 gpm up to maximum flow (to increase flow,
simply trim back orifice). Orifice steps control flow as follows: Step 1 = 10 gpm, Step 2 = 20 gpm, Step 3 = 30
gpm, Step 4 (maximum opening) = maximum flow (see Fig. 1).
Fig. 1
Step 1
Step 2
Note: ALWAYS use a 1” I.D. hose properly secured to the barb spout using a hose clamp.
Step 3
Step 4
Operation
1. Make sure the motor (electric or air) is properly installed on the pump tube and is in the off position. See
motor instruction manual for motor installation instructions.
2. Insert the pump tube into the uid to be dispensed and the hose into the container to be lled prior to
starting the pump. Bung adapters are available to provide a tighter t between the pump tube and bung
opening of a standard drum. Check drum pump accessories at www.nishthompson.com or contact your
local Finish Thompson distributor for bung adapter info.
3. Make sure the pump’s discharge hose is properly secured before operating the motor.
4. Begin pumping by turning the motor on and verifying that there are no leaks. If leaks are noticed immedi-
ately turn the motor off and check all discharge hose connections.
NEVER allow the pump to run dry.
Maintenance
Disassembly
1. Remove the housing cover (item 16) by turning it clockwise (left hand thread) while gripping the impeller
housing (item 14).
2. Turn the impeller (item 15) counterclockwise (right-hand thread) while holding the coupling half (item 2)
with the other hand to prevent the shaft from turning and remove it.
8
3. Remove the impeller housing (item 14) by gripping the intake tube and spinning the housing clockwise
(left hand thread).
4. Place a wooden board or rubber mat on the floor (to protect threads on the bottom of the shaft) and gently
tap shaft (item 14) on it until the bearings (item 3) are exposed at the top of the pump. Pull the bearings and
shaft out through the top of the pump. Shaft can be removed from the bearing sleeve by unthreading it
counterclockwise (right hand thread).
5. Place the pump head (item 6) in a vise (do not crush) and remove the intake tube (item 7) by unthreading
clockwise (left hand thread). Remove the inner tube (item 10) and shaft sleeve (item 8) from the head using a
twist-pull motion.
6. Use a hook tool to remove the lip seal (item 5) from the head.
7. To remove the center support (item 11) from the inner tube (item 10), spread open fingers and disengage it
from the inner tube.
Inspection
1. Check the housing cover (item 16), the impeller (item 15), and the impeller housing (item 14) for wear, rubbing, or damage from foreign objects. Replace if damaged.
Note: The double impeller design of this pump is dependant on the impeller working correctly. Any damage
to the impeller can cause pump failure.
2. Inspect the pump shaft (item 4) for wear in the bottom (item 12), and the FKM lip seal (item 5) areas. Replace the shaft if needed.
3. Inspect the bottom bearing (item 12) and the shaft sleeve (item 8) for internal wear. Inspect all o-rings (items
9, 13, & 17) for nicks or chemical attack. Replace as needed.
4. Inspect the bearing assembly (item 3) for rust or corrosion. Never reuse the lip seal (item 5).
Reassembly
1. Install new lip seal (item 5) into the pump head (item 6) with the grooved side facing the bottom of the
pump.
2. Thread the longer threaded end of the shaft (item 4) into the bearing assembly (item 3) and hand tighten.
Carefully insert the shaft from the top through the vapor seal and head (items 5 & 6) and seat the bearing
assembly (item 3) into the head (item 6)
3. If o-rings are replaced: Install 2 upper inner tube o-rings (items 9), and install the impeller housing o-ring
(item 13) inside the top of the housing (item 14). Apply a small amount of Vaseline to the o-rings to aid in
assembly. Install the center support (item 11) onto the inner tube (item 10).
4. Slide the inner tube (item 10) up the shaft and into the counter bore in the bottom of the head. Slide the shaft
sleeve (item 8) up inside the inner tube. Slide the intake tube up from the bottom, centering the center support, and thread it (left hand thread) into the head (item 6).
5. Gripping the coupling (item 7) at the top of the pump, thread the impeller on (right hand thread). Install the
housing cover (left hand thread). Turn the coupling to verify there is no binding inside the pump.
9
PFM/PFP/PFV SPARE PARTS EXPLODED VIEW
10
PUMP SPARE PARTS LIST
ITEM QTY DESCRIPTION
1 1
2 1
3* 1
4 1
5* 1
6 1
7 1
8* 1
9* 2
10 1
1 (27-48”)
11*
2 (60”)
3 (72”)
12* 1
13* 1
14* 1
15* 1
COUPLING INSERT
NITRILE J100014 J100014 J100014
COUPLING HALF
CAST ALUMINUM 1/4”-20 THREAD FOR S/N 211770 & UP J100012-2 J100012-2 J100012-2
BEARING ASSEMBLY (INCLUDES COUPLING HALF)
STEEL A101110 A101110 A101110
MAIN SHAFT (PFM = 316SS, PFP/PFV = ALLOY 625)
27” MODELS M100004-5 M100004-1 M100004-1
40” MODELS M100004-7 M100004-3 M100004-3
48” MODELS M100004-8 M100004-4 M100004-4
54” MODELS M100004-17 M100004-15 M100004-15
60” MODELS M100004-12 M100004-9 M100004-9
72” MODELS M100004-13 M100004-11 M100004-11
LIP SEAL
1/4” FKM (STANDARD) 107592 107592 107592
1/4” EKONOL (OPTIONAL) 107622 107622 107622
HEAD
POLYPROPYLENE 107755-1 107755-1 N/A
PVDF N/A N/A 107755-2
INTAKE TUBE (PFM/PFP = POLYPROPYLENE, PFV = PVDF)
27” MODELS 107475-2 107475-2 107475-7
40” MODELS 107475-3 107475-3 107475-8
48” MODELS 107475-4 107475-4 107475-9
54” MODELS 107475-12 107475-12 107475-13
60” MODELS 107475-5 107475-5 107475-10
72” MODELS 107475-6 107475-6 107475-11
SHAFT SLEEVE (ALL MODELS = PTFE)
27” MODELS 108375-2 108375-2 108375-2
40” MODELS 108375-3 108375-3 108375-3
48” MODELS 108375-4 108375-4 108375-4
54” MODELS 108375-7 108375-7 108375-7
60” MODELS 108375-5 108375-5 108375-5
72” MODELS 108375-6 108375-6 108375-6
INNER TUBE O-RING
FKM (STANDARD) J100249 J100249 J100249
EPDM 106519 106519 106519
PERLAST 105621 105621 105621
INNER TUBE (PFM/PFP = POLYPROPYLENE, PFV = PVDF)
27” MODELS 108373-2 108373-2 108373-7
40” MODELS 108373-3 108373-3 108373-8
48” MODELS 108373-4 108373-4 108373-9
54” MODELS 108373-12 108373-12 108373-13
60” MODELS 108373-5 108373-5 108373-10
72” MODELS 108373-6 108373-6 108373-11
CENTER SUPPORT
ETFE 108277 108277 108277
BOTTOM BEARING
PTFE M100007 M100007 M100007
IMPELLER HOUSING O-RING
FKM (STANDARD) J100019 J100019 J100019
EPDM 106799 106799 106799
PERLAST 105622 105622 105622
IMPELLER HOUSING
POLYPROPYLENE 107316-1 107316-1 N/A
PVDF N/A N/A 107316-2
IMPELLER ASSEMBLY
PVDF A100002-2 A100002-2 A100002-2
PART NUMBER
MODEL PFM MODEL PFP MODEL PFV
11
ITEM QTY DESCRIPTION
HOUSING COVER
16* 1
17 1
18 1
19 1
*Recommended Spare Parts
Note: Bearing assembly and lip seal can be purchased as a kit using part number 108110.
POLYPROPYLENE M101612-1 M101612-1 N/A
PVDF N/A N/A M101612-2
DISCHARGE O-RING
FKM (STANDARD) J100991 J100991 J100991
EPDM J102378 J102378 J102378
PERLAST 107017 107017 107017
DISCHARGE NUT
FOR USE WITH 1” OR 3/4” BARB SPOUT & GARDEN HOSE ADAPTER M101610-1 M101610-1 M101610-2
FOR USE WITH 1” MNPT SPOUT ONLY 106622 106622 106622-1
SPOUT
1” BARB (STANDARD) M100028-1 M100028-1 M100028-2
3/4” BARB (OPTIONAL) 105439-1 105439-1 105439
3/4” MALE GARDEN HOSE ADAPTER (OPTIONAL) 110135-1 110135-1 N/A
1” MNPT (OPTIONAL) 106599 106599 106599-1
PART NUMBER
MODEL PFM MODEL PFP MODEL PFV
N/A = Not Applicable
Service 1-800-888-3743
P/N 108097, Rev. 6, 3/26/2019
Loading...