TBP SERIES PUMPS
OPERATION & PARTS MANUAL
EU Declaration of Conformity
Finish Thompson Inc. hereby declares that the following machine(s) fully comply with the
applicable health and safety requirements as specified be the EC Directives listed.
The product may not be taken into service until it has been established that the drive motor
for the Drum and Container Pump complies with the provisions of all relevant EC Directives.
The complete product complies with the provisions of the EC Directive on machinery safety
provided motors manufactured by Finish Thompson Inc. are used.
This declaration is valid provided that the devices are fully assembled and no modifications
are made to these devices.
BTS – 40 EPPI/EPPS 15/27/40 EFP/EFV/EFS-16/27/40/48
HVDP LR-27/40/48 HVDP HR-27/40/28 PFM-27/40/48/60
PFP-15/27/40/48/60/72 PFS-27/40/48/60/72 PFV-27/40/48/60/72
TBP-27/40/48 TBS-40 TTC/TTS-27/40/48
STTS-40 TMS-40
Type of Device:
Drum and Container Pump Tubes
Models:
EC Directives:
Machinery Safety (2006/42/EC)
Applied Harmonized Standards:
EN ISO 12100 Part 1
EN ISO 12100 Part 2
EN 809
Manufacturer:
Finish Thompson Inc.
921 Greengarden Road
Erie, Pennsylvania 16501-1591 U.S.A
Signed,
_
President
January 7, 2013
Person(s) Authorized to Compile Technical File: Michael Smith Engineers Limited
Oaks Road, Woking, Surrey
GU21 6PH, UK
Telephone: 01483 771871
Introduction
This manual pertains to the TBP Series drum pumps. Finish Thompson Inc. thanks you for choosing our products. We
believe the use of our products will be fully satisfactory. When properly installed and operated, your Finish Thompson
motor and pump will provide long, trouble-free service; therefore, please read this manual carefully before carrying
out any operations on the pump/motor unit. Any use other than that described herein is considered incorrect; and,
consequently, Finish Thompson Inc. shall not be held responsible for any damages to people or property. In case of
doubt or enquiries, please reply to our Technical Service department directly at the following address:
Finish Thompson, Inc.
921 Greengarden Rd.
Erie, PA 16501 U.S.A.
Tel. 1-814-455-4478; Fax 1-814-455-8518
www.finishthompson.com; fti@finishthompson.com
Index
Introduction ............................................................................................................................. 1
Warranty, General Terms & Conditions ...................................................................................... 2
Safety ...................................................................................................................................... 3
Pump Specifications ................................................................................................................ 4
Installation ............................................................................................................................... 5
Maintenance
Disassembly ....................................................................................................................... 5
Inspection ........................................................................................................................... 6
Reassembly ........................................................................................................................ 6
Exploded View ......................................................................................................................... 7
Pump Tube Spare Parts List ..................................................................................................... 8
Technical Service Hotlne: 1-800-888-3743 or email techservice@finishthompson.com
1
Warranty, General Terms & Conditions
1. The following terms and conditions apply to the sale of machinery, components and related services and products, of Finish
Thompson Inc. (hereinafter “the products”)
2. Finish Thompson Inc. (the manufacturer) warrants only that:
a) its products are free of defects in material, design and workmanship at the time of original purchase;
b) its products will function in accordance with Finish Thompson Inc. operation manuals; Finish Thompson Inc. does not
guarantee that the product will meet the precise needs of the Customer, except for those purposes set out in any invitation
to render documents or other documents specifically made available to Finish Thompson Inc. before entering into this
agreement;
c) high quality materials are used in the construction of the pumps and that machining and assembly are carried out to the
highest standards. Except as expressly stated above, Finish Thompson Inc. makes no warranties, express or implied,
concerning the products, including all warranties of fitness for a particular purpose.
This warranty shall not be applicable in circumstances other than defects in material, design, and workmanship. In particular
warranty shall not cover the following:
d) Periodic checks, maintenance, repair and replacement of parts due to normal wear and tear;
e) Damage to the product resulting from:
i. Tampering with, abuse or misuse, including but not limited to failure to use the product for its normal purposes as
stated at the time of purchase or in accordance with Finish Thompson, Inc. instructions for use and maintenance of the
product, or the installation or improper ventilation or use of the product in a manner inconsistent with the technical or
safety standard in force;
ii. Repairs performed by non-authorized service workshop, or opening of the unit by non-authorized personnel, or use of
non genuine Finish Thompson Inc. parts;
iii. Accidents, force majeure or any cause beyond the control of Finish Thompson Inc., including but not limited to light ning, water, fire, earthquake, and public disturbances, etc.
3. The warranty shall cover the replacement or repair of any part, which is documented to be faulty due to construction or as sembling, with new or repaired parts free of charge delivered by Finish Thompson, Inc. Parts subjected to normal wear and
tear shall not be covered by the warranty. Finish Thompson, Inc. shall decide as to whether the defective or faulty part shall be
replaced or repaired. Transportation charges are prepaid to Finish Thompson.
4. The warranty of the products shall be valid for a period of 12 months from the date of delivery, under the condition that notice
of the alleged defect to the products or parts thereof be given to Finish Thompson, Inc. within the term of 8 days from the
discovery.
5. Repair or replacement under the terms of this warranty shall not give a right to an extension to, or a new commencement of,
the period of warranty. Repair or replacement under the terms of this warranty may be fulfilled with functionally equivalent re conditioned units. Finish Thompson Inc. qualified personnel shall be solely entitled to carry out repair or replacement of faulty
parts after careful examination of the motor. Faulty parts or components when replaced by Finish Thompson Inc. will become
the property of Finish Thompson Inc. If this warranty does not apply, the purchaser shall bear all cost for labor, material and
transportation.
6. Finish Thompson Inc. will not be liable on any claim, whether in contact, tort, or otherwise, for any indirect, special, incidental,
or consequential damages, caused to the customer or to third parties, including loss of profits, process down time, transpor tation costs, costs associated with replacement or substitution products, labor costs, installation or removal costs. In any and
all events, manufacturer’s liability shall not exceed the purchase price of the product and/or accessories.
7. Return Policy. Should you have any problems with this product, please contact the distributor in your area. The distributor
will determine if a return to the factory is necessary and will contact the factory for a Return Authorization Number. Otherwise,
contact our Technical Service Hotline (1-800-888-3743) or e-mail techservice@finishthompson.com if you have any questions
regarding product operation or repair.
2
Safety
1. Introduction
This manual contains all the information needed for the correct installation, use and maintenance of your new Finish Thompson
pump. It should be read and understood by all the personnel involved in installation, operating and servicing of the pump before
it is started.
2. Operator Qualification and Training
The personnel in charge of the installation, the operation, and the maintenance of the pump must be qualified and able to per form the operations described in this manual. Finish Thompson, Inc. shall not be held responsible for the training level of
personnel and for the fact that they are not fully aware of the contents of this manual.
3. Safety Instructions
FOR YOUR OWN SAFETY
BEFORE using or servicing your pump, please make sure to wear the proper clothing, eye protection and follow standard safety
procedures when handling corrosive or personally harmful materials.
GENERAL DANGER
ALWAYS use a stainless steel pump tube with an explosion proof electric motor or air motor and static protection kit with
grounded discharge hose when pumping or mixing flammable or combustible material.
ALWAYS use and store the pump and motor in an upright position.
DANGER: POWER SUPPLY
Refer to instructions in the appropriate motor Operation & Installation Manual.
4. Noise Level
Refer to specifications in the appropriate motor Operation & Installation Manual.
5. Modifications and Spare Parts
Any changes concerning the service of the pump as originally purchased can be executed only after written approval from
Finish Thompson Inc. It is recommended to use only genuine Finish Thompson Inc. spare parts and approved accessories. The
use of non-original spare parts or non-approved accessories will void warranty and removes any responsibility on the manufac turer’s behalf for any damage caused to people or things.
6. Cleaning
It is highly recommended to flush pumps with clean water or some other neutralizing fluid compatible with pump materials
when done pumping or when switching chemicals.
3
PUMP SPECIFICATIONS
Outer Tube Diameter 1.66” (4.2 cm)
Discharge Thread 1” hose barb
Max. Specific Gravity 1.4
Max. Viscosity 200 cP
Min./ Max. Fluid
Temperature
Wetted Materials Pure polypropylene, pure PVDF, PTFE, Alloy 625
MODEL TBP
35°F Min. to 150°F Max.
(1.6°C Min. to 66°C Max.)
4
Installation & Maintenance Instructions
Installation
1. Remove the drum pump and motor from its packaging and inspect for shipping damage.
2. Turn the pump coupling to verify there is no binding.
3. Adjust the coupling so that the empty slots in the insert are at 3 and 9 o’clock with the pump discharge at 12
o’clock.
4. Install the motor according to instructions in the appropriate motor manual.
5. Attach discharge hose and install pump into the container.
Note: Pumps with the standard 1” barb spout ship with a variable orifice fitting, which limits the flow of the
pump to 10 gpm. As it is cut away, flow will increase minimum up to maximum flow (to increase flow, simply
trim back orifice) See Fig. 1.
Fig. 1
Step 1
Step 2
Step 3
Maintenance
Disassembly
1. Carefully place the pump head (item 5) in a vice (do not crush), and unthread the intake tube (item 6) by
turning it clockwise (left hand thread). Pull the intake tube (item 6) carefully off the bottom of the pump
shaft.
2. Holding the pump coupling half (item 2) in one hand, unthread the pump shaft (item 10) from the bearing
assembly (item 3) by turning it counterclockwise (right hand threads).
3. Remove the bearing assembly (item 3) and the seal assembly (item 4) from the pump head (item 5) being
careful not to damage the threaded area at the bottom of the bearing assembly. Discard the seal assembly
(never reuse the seal).
5
Inspection
1. Visually inspect the compressor (item 11), and the 3 center bearings (item 9) for wear or damage. Replace as
needed.
2. Inspect the bearing assembly (item 3) for rust, corrosion, or tightness. Replace as needed.
3. Inspect the pump shaft in the seal area for wear and replace as needed.
Reassembly
1. Install the intake tube (item 6) into the pump head (item 5) by threading it counterclockwise (left hand
threads).
2. Insert the pump shaft assembly up through the bottom of the intake tube until the threaded part of the
shaft sticks out slightly from the pump head.
3. Warm up the seal assembly (item 4) with a heat lamp or by soaking it in hot water to aid in the installation
process.
4. Slide the seal over the shaft threads and onto the shaft so that the lip in the center of the seal is facing the bottom of the pump. Push the seal just past the steop on the shaft being careful not to damage the lip.
5. Thread on the bearing assembly. Carefully press the bearing assembly into the pump head, until the top of the
bearings are flush with the top of the pump head.
6. Turn the coupling half to verify there is no binding inside the pump.
Note: Repair instructions can be downloaded from our web site at www.finishthompson.com or contact Technical Service at
1-800-888-3743.
6
TBP SPARE PARTS EXPLODED VIEW
7
SPARE PARTS LIST
ITEM QTY DESCRIPTION PART NUMBER
1 1
2 1
3* 1
4* 1
5 1
6 1
7 1
8 1
9 2
10 1
11 1
12 1
13 1
14 1
*Recommended Spare Parts
COUPLING INSERT
J100014
COUPLING HALF
J100012
BEARING ASSEMBLY
W/ ROLL PIN A101110
SEAL ASSEMBLY
PTFE A103186
PUMP HEAD
PURE PVDF M102222
INTAKE TUBE ASSEMBLY
27” PURE POLYPROPYLENE M102221-1
40” PURE POLYPROPYLENE M102221-2
48” PURE POLYPROPYLENE M102221-3
IMPELLER ASSEMBLY
PTFE WITH ALLOY 625 PIN A103190
SPACER SET
27” PURE POLYPROPYLENE A103189-1
40” PURE POLYPROPYLENE A103189-2
48” PURE POLYPROPYLENE A103189-3
CENTER BEARING
PTFE M100039-1
SHAFT
27” ALLOY 625 M102219-1
40” ALLOY 625 M102219-2
48” ALLOY 625 M102219-3
COMPRESSOR
PTFE WITH ALLOY 625 PIN A103191
DISCHARGE O-RING
FKM J100991
SPOUT
1” BARBED PURE PVDF 106753
DISCHARGE NUT
PURE PVDF M101610-2
Service 1-800-888-3743
P/N 108100 REV. 3, 2/10/2014
Loading...