FINISAR FTLF1323P1BTL Datasheet

Download

Page 1

F i n i s a r

Product Specification

OC-3 LR-1/STM L-1.1 RoHS Compliant Pluggable SFP Transceiver

FTLF1323P1xTL

PRODUCT FEATURES

• 155 Mb/s bi-directional data links

• Hot-pluggable SFP footprint

• Built-in digital diagnostic functions

• Uncooled Fabry-Perot 1310nm

laser transmitter

• Duplex LC connector

• RoHS compliant and lead-free

• Metal enclosure, for lower EMI

• Single 3.3V power supply

• Low power dissipation <700mW

typical

• Industrial operating temperature range: -40°C to 85°C

Finisar’s FTLF1323P1xTL Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA) They comply with SONET and SDH standards diagnostics functions are available via the 2-wire serial bus specified in the SFP MSA. They are RoHS compliant and lead-free per Directive 2002/95/EC Application Note AN-2038.

PRODUCT SELECTION

APPLICATIONS

• SONET OC-3 LR-1 / SDH STM L-1.1

at OC-3 LR-1/STM L-1.1. Digital

and Finisar

FTLF1323P1xTL

 Finisar Corporation December 2, 2005 Rev.A Page 1

W Wide Extraction Bail

B Narrow Extraction Bail

Page 2

FTLF1323P1xTL Pluggable SFP Product Specification - December 2005 F i n i s a r

I. Pin Descriptions

Pin Symbol Name/Description Ref.

1 V 2 T 3 T

EET

FAULT

Transmitter Disable. Laser output disabled on high or open. 2

DIS

4 MOD_DEF(2) Module Definition 2. Data line for Serial ID. 3 5 MOD_DEF(1) Module Definition 1. Clock line for Serial ID. 3 6 MOD_DEF(0) Module Definition 0. Grounded within the module. 3 7 Rate Select No connection required 4 8 LOS Loss of Signal indication. Logic 0 indicates normal operation. 5

9 V 10 V 11 V 12 RD-

EER

13 RD+ Receiver Non-inverted DATA out. AC Coupled. 14 V 15 V 16 V 17 V

EER

Receiver Power Supply

CCR

Transmitter Power Supply

CCT

EET

18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. 19 TD20 V

EET

Notes:

1. Circuit ground is internally isolated from chassis ground.

2. Laser output disabled on T

3. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.5V. MOD_DEF(0) pulls line low to indicate module is plugged in.

4. Finisar FTLF1323P1xTL transceivers do not require rate control.

5. LOS is open collector output. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.5V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.

Transmitter Ground (Common with Receiver Ground) 1

Transmitter Fault. Not supported.

Receiver Ground (Common with Transmitter Ground) 1 Receiver Ground (Common with Transmitter Ground) 1 Receiver Ground (Common with Transmitter Ground) 1 Receiver Inverted DATA out. AC Coupled.

Receiver Ground (Common with Transmitter Ground) 1

Transmitter Ground (Common with Receiver Ground) 1

Transmitter Inverted DATA in. AC Coupled. Transmitter Ground (Common with Receiver Ground) 1

>2.0V or open, enabled on T

DIS

<0.8V.

DIS

Towards

Bezel

VeeT

TXFault

TX Disable

MOD-DEF(2)

MOD-DEF(1)

MOD-DEF(0)

Rate Select

LOS

VeeR

VeeT

TD-

TD+

VeeT

VccT

VccR

VeeR

RD+

RD-

VeeR

Towards

ASIC

Pinout of Connector Block on Host Board

 Finisar Corporation December 2, 2005 Rev.A Page 2

Page 3

FTLF1323P1xTL Pluggable SFP Product Specification - December 2005 F i n i s a r

II. Absolute Maximum Ratings

Parameter Symbol Min Typ Max Unit Ref.

Maximum Supply Voltage Vcc -0.5 4.5 V Storage Temperature T Case Operating Temperature T

Relative Humidity RH 0 85 % 1

III. Electrical Characteristics (T

Parameter Symbol Min Typ Max Unit Ref.

Supply Voltage Vcc 3.10 3.50 V Supply Current Icc 165 300 mA

Transmitter

Input differential impedance R Single ended data input swing Vin,pp Transmit Disable Voltage V Transmit Enable Voltage V Transmit Disable Assert Time

Receiver

Single ended data output swing Vout,pp Data rise/fall time tr 400 1300 ps 5 LOS Fault V LOS Normal V Power Supply Rejection PSR

Notes:

1. Non condensing.

2. AC coupled.

3. Or open circuit.

4. Into 100 ohm differential termination.

5. 10 – 90 %

6. Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.

= -40 to 85 °°°°C, VCC = 3.10 to 3.50 Volts)

LOS fault

LOS norm

7. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5

MHz up to specified value applied through the power supply filtering network shown on page 23 of the Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA), September 14, 2000. Valid on receive side for input powers within receive sensitivity.

-40 100

-40 85

°C °C

100

Ω

250 1200 mV

Vcc – 1.3 Vcc V

Vee Vee+ 0.8 V 3

µs

300 400 800 mV 4

Vcc – 0.5 Vcc

V 6

HOST

Vee Vee+0.5 V 6

50 mVpp 7

 Finisar Corporation December 2, 2005 Rev.A Page 3

Page 4

FTLF1323P1xTL Pluggable SFP Product Specification - December 2005 F i n i s a r

IV. Optical Characteristics (T

Parameter Symbol Min Typ Max Unit Ref.

Transmitter

Output Opt. Pwr: 9/125 SMF P Optical Wavelength Spectral Width Optical Extinction Ratio ER Optical Rise/Fall Time tr/ t Relative Intensity Noise RIN Generated Jitter (peak to peak) JTXp-p Generated Jitter (rms) JTXrms Mask Margin 20%

Receiver

Average Rx Sensitivity R Optical Center Wavelength LOS De-Assert LOS LOS Assert LOS LOS Hysteresis

Notes

1. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations.

2. Unfiltered, 20-80%

3. Jitter measurements taken using Agilent OMNIBERT 718 in accordance with GR-253.

4. With worst-case extinction ratio. Measured with a PRBS 2

= -40 to 85 °°°°C, VCC = 3.10 to 3.50 Volts)

OUT

λ σ

-5 0 dBm 1

1263 1360 nm

3 nm

10 dB

1300 ps 2

-120 dB/Hz

0.07 UI 3

0.007 UI 3

SENS1

-34 -10 dBm 4

1260 1600 nm

-34 dBm

-45 dBm

0.5 dB

-1 test pattern.

 Finisar Corporation December 2, 2005 Rev.A Page 4

Page 5

FTLF1323P1xTL Pluggable SFP Product Specification - December 2005 F i n i s a r

V. General Specifications

Parameter Symbol Min Typ Max Units Ref.

Data Rate BR 155 155 Mb/sec 1 Bit Error Rate BER 10 Max. Supported Link Length on 9/125µm SMF @ OC-3

Notes:

1. Compliant with SONET and SDH at OC-3 LR-1/STM L-1.1.

2. Tested with a PRBS 2

-1 test pattern.

40 km 4

MAX5

3. Attenuation of 0.55 dB/km is used for the link length calculations (per GR-253 CORE). Distances are

indicative only. Please refer to the Optical Specifications in Table IV to calculate a more accurate link budget based on specific conditions in your application.

VI. Environmental Specifications

Finisar 1310nm SFP transceivers have an industrial operating temperature range from –40°C to +85°C case temperature.

Parameter Symbol Min Typ Max Units Ref.

Case Operating Temperature T Storage Temperature T

sto

-40 85 °C

-40 100 °C

VII. Regulatory Compliance

Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TÜV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request.

-12

 Finisar Corporation December 2, 2005 Rev.A Page 5

Page 6

FTLF1323P1xTL Pluggable SFP Product Specification - December 2005 F i n i s a r

VIII. Digital Diagnostic Functions

Finisar FTLF1323P1xTL SFP transceivers support the 2-wire serial communication protocol as defined in the SFP MSA1. It is very closely related to the E2PROM defined in the GBIC standard, with the same electrical specifications.

The standard SFP serial ID provides access to identification information that describes the transceiver’s capabilities, standard interfaces, manufacturer, and other information.

Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory-set normal range.

The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged. The interface is identical to, and is thus fully backward compatible with both the GBIC Specification and the SFP Multi Source Agreement. The complete interface is described in Finisar Application Note AN-2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”.

The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially.

For more information, please see the SFP MSA documentation Note AN-2030.

Digital diagnostics for the FTLF1323P1xTL are externally calibrated by default.

Please note that evaluation board FDB-1018 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface.

or Finisar Application

 Finisar Corporation December 2, 2005 Rev.A Page 6

Page 7

FTLF1323P1xTL Pluggable SFP Product Specification - December 2005 F i n i s a r

IX. Mechanical Specifications

Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA) 3.

FTLF1323P1BTL

 Finisar Corporation December 2, 2005 Rev.A Page 7

Page 8

FTLF1323P1xTL Pluggable SFP Product Specification - December 2005 F i n i s a r

FTLF1323P1WTL

 Finisar Corporation December 2, 2005 Rev.A Page 8

Page 9

FTLF1323P1xTL Pluggable SFP Product Specification - December 2005 F i n i s a r

X. PCB Layout and Bezel Recommendations

 Finisar Corporation December 2, 2005 Rev.A Page 9

Page 10

FTLF1323P1xTL Pluggable SFP Product Specification - December 2005 F i n i s a r

 Finisar Corporation December 2, 2005 Rev.A Page 10

Page 11

FTLF1323P1xTL Pluggable SFP Product Specification - December 2005 F i n i s a r

XI. References

1. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 2000. Documentation is currently available at Finisar upon request.

2. Bellcore GR-253 and ITU-T G.957 Specifications.\

3. Directive 2002/95/EC of the European Council Parliament and of the Council, “on the restriction of the use of certain hazardous substances in electrical and electronic equipment.” January 27, 2003.

XII. For More Information

Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138

sales@finisar.com www.finisar.com

 Finisar Corporation December 2, 2005 Rev.A Page 11