Fine Offset Electronics HP2002 User Manual

Wireless weather station

Operation Manual

- 1 -

OVERVIEW

Outdoor sensor:

1. Wind Vane

2. Wind Speed Sensor

3. Solar panel

4. Battery compartment

5. LED Indicator: light on for 4s if the unit power up. Then the LED will flash once every 16 seconds (the

sensor transmission update period).

6. Reset button

7. Thermo-hygro sensor

8. UV sensor

9. Light sensor

10. Rain collector

11. Bubble level

- 2 -

Indoor sensor

Display unit

memory card slot

Power jack
reset

Contents

The weather station consists of the following parts.

QTY Item

1 Display Console
1 Outdoor sensor(Thermo-hygrometer / Rain Gauge / Wind Speed Sensor /Transmitter)
1 Wind Vane
1 Indoor sensor
1 5V DC adaptor
1 Stainless Steel Tube (D32*H200mm)

1
3

1 Zip bag for 1pc Allen wrench
1 User manual

U style Stainl ess Steel Loop
AA 1.5V rechargeable batteries for outdoor sensor

- 3 -

Introduction

Thank you for your purchase this professional weather statio n. The outdo or sensor is solar powered a nd sends
data to the console via a low-power radio. It allows you to upload your weather data to weather website:

www.wunderground.com

This manual will guide you step-by-step through setting up your device. Use this manual to become familiar
with your professional weather station, and save it for future reference.

which you can share it with your friend.

Installation

Before placing and installing all components of the weather station at the re final destination, please set up the
weather station with all parts being nearby for testing the correct function.

Outdoor sensor

1. Attach the wind vane

Push the wind vane into the shaft. as shown in figure 1.
Tighten the set screw with the Allen Wrench (included) as shown in figure 2. Make sure the wind vane spin
freely.

Figure 1 Figure 2

2. Install Mounting Pole

Insert the pole into the base, as shown in figure 3. Spin the lid onto the base as shown in figure 4.

Togue and
groove joint

Figure 3

- 4 -

Figure 4

3. Install Batteries

Locate the battery door on the thermo-hygrometer / rain gauge tra nsmitter, as shown in Figure 5. Turn the set
screw counter clockwise to loosen the screw to open the battery compartment. Insert 3XAA rechargeable
batteries in the battery compartment The LED indicator on the back of the transmitter will turn on for four
seconds and normally flash once every 16 seconds (the sensor transmission update period).

Note: If no LED light up or is lighted permanently , make sure the battery is inserted the correct way or a proper
reset is happened. Do not install the batteries backwards. You can permanently damage the
thermo-hygrometer.

Figure 5

- 5 -

4. Mount outdoor sensor

Fasten the mounting pole to your mounting pole or bracket
(purchased separately) with the two U-bolts, mounting pole brackets
and nuts, as shown in Figure 6.

Tighten the mounting pole to your mounting pole with the U-Bolt
assembly, as shown in Figure 7..

Figure 6

Figure 8

Figure 7

there are four alphabet letter of “N”,”E”,”S”and “W”
representing for the direction of North, East, South and
West, as Figure 8. Wind direction sensor has to be
adjusted so that the directions on the sensor are
matching with your real location. Permanent wind
direction error will be introduced when the wind
direction sensor is not positioned correctly during
installation.

Level the sensors

Use the bubble level on the rain sensor as a guide to
verify that sensors are level.

Figure 9

- 6 -

5. Reset Button and Transmitter LED

In the event the ourdoor sensor is not transmitting, reset the outdoor sensor.
With an open ended paperclip, press and hold the RESET BUTTON for three seconds to completely discharge

the voltage.
Take out the batteries and wait one minute, while covering the solar panel to drain the voltage.
Put batteries back in and resynchronize with console by powering down and up the console with the sensor

about 10 feet away.

Figure 10

Indoor sensor

Remove the battery door on the back of the sensor with a Philips screwdriver (there is only one screw, at the
bottom of the unit). Insert two AAA batteries as shown in Figure 10 (we recommend lithium batteries for cold
weather climates, but alkaline batteries are sufficient for most climates).

Replace the battery door and set screw. Note that the temperature, humidity and pressure will be displayed on
the LCD display. Looking at the back of the unit from left to right, the polarity is (-) (+) for the top battery and (+)
(-) for the bottom battery.

Figure 10

- 7 -

Initial Display Console Set Up

Connect the power adapter to power up the display console.
The display console starts to register the transmitter and receiver the weather data from transmitter. The

interface as below

:

Then it start to scan the Wi-Fi network, if it didn’t found the available Wi-Fi it will shows” not find any AP
(Access Point)”. Press

the data to weather website. If the data upload to server successfully, the icon
wind chill.

key to return to normal display mode. Only after connect to WLAN you can upload

will show on beneath the

Program Mode

1. Normal display Mode

- 8 -

1. Wind direction 10. Rainfall

2. Low battery indicator 11. Heat index

3. Weather Forecast / rel. pre ssure graph

12. Dew point
/ In & Outdoor temperature graph / In &
Outdoor humidity graph

4. UV index 13. Outdoor Temperature &Humidity

5. Light 14. Indoor Temperature &Humidity

6. Barometric Pressure 15. Internet Connectivity

7. sunrise/sunset 16. WiFi Connectivity

8. moon phase 17. Wind chill

9. Time and date 18. Gust

19. Wind speed

Each icon in the display matches a black keys on plastic case. Please press the keys for operation.

- 9 -