• 5 mm wide
• Low coil power
• PCB or 93 series sockets
1
1 CO (SPDT)
6/10
250/400
1,500
300
0.185
6/0.2/0.12
500 (12/10)
AgNi
—
5 - 12 - 24 - 48 - 60
—/0.17
—
(0.7…1.5)U
N
—/0.4 U
N
—/0.05 U
N
—/10 · 10
6
60 · 10
3
5/3
6
1,000
–40…+85
RT II
34.51
34 Series - Slim electromechanical PCB relays 6 A
Contact specification
Contact configuration
Rated current/Maximum peak current A
Rated voltage/Maximum switching voltage V AC
Rated load AC1 VA
Rated load AC15 (230 V AC) VA
Single phase motor rating (230 V AC) kW
Breaking capacity DC1: 30/110/220 V A
Minimum switching load mW (V/mA)
Standard contact material
Coil specification
Nominal voltage (U
N
) V AC (50/60 Hz)
V DC
Rated power AC/DC VA (50 Hz)/W
Operating range AC
DC
Holding voltage AC/DC
Must drop-out voltage AC/DC
Technical data
Mechanical life AC/DC cycles
Electrical life at rated load AC1 cycles
Operate/release time ms
Insulation between coil and contacts (1.2/50 µs)
kV
Dielectric strength between open contacts V AC
Ambient temperature range °C
Environmental protection
Approvals (according to type)
Copper side view
Features
Ultra-slim 1 Pole - 6 A relay
Printed circuit mount
- direct or via PCB socket
35 mm rail mount
- via screw or screwless sockets
• 1 Pole changeover contacts or
1 Pole normally open contact
• Ultra slim, 5 mm, package
• Sensitive DC coil - 170 mW (Dual AC/DC coil
drive possible using 93 series sockets)
• UL Listing (certain relay/socket combinations)
• Cadmium Free contact materials
• 8/8 mm clearance/creepage distance
• 6 kV (1.2/50 µs) insulation, coil-contacts
FORUL H
ORSEPOWER ANDPILOTDUTY RATINGS
SEE“General technical information” page
V
28 5
153.5
0.4 1 0.4
A2 A1 12 11 14
0.8 1.3
3.755511.25
1.3
28
5
1.9
1 NO (SPST-NO) 1 NO (SPST-NO) 1 NO (SPST-NO)
2/20 0.1/0.5 2/40
(24/33)DC (48/60)DC (240/275)AC
(1.5...24)DC (1.5...48)DC (12...240)AC
10.0522
0.001 0.001 1.5
0.12 1 1.6
5 24 60 24 60 5 24 60
3.5...12 16...30 35...72 16...30 35...72 3.5...10 16...30 35...72
77 3 7 3 1273
1 10 20 10 20 1 10 20
715 3,200 21,300 3,200 21,300 416 3,200 21,300
0.1/0.3* 0.02/0.1* 12/12*
2,500 2,500 2,500
–20...+60 –20...+60 –20...+60
RT III RT III RT III
—
2
34.81-9024 34.81-7048 34.81-8240
Output circuit
Contact configuration
Rated current/Maximum peak current (10 ms) A
Rated voltage/Maximum blocking voltage V
Switching voltage range V
Minimum switching current mA
Max. “OFF-state” leakage current mA
Max. “ON-state” voltage drop V
Input circuit
Nominal voltage V DC
Operating range V DC
Control current mA
Release voltage V DC
Impedance Ω
Technical data
Operate/release time ms
Dielectric strength between input/output V
Ambient temperature range °C
Environmental protection
Approvals (according to type)
Copper side view Copper side view Copper side view
input output input output
34 Series - Slim solid state PCB relays (SSR) 0.1 - 2 A
* Note: all technical data relates to using the relay directly on PCB or PCB socket type 93.11.
If the relay is use with 35 mm rail socket types 93.01 or 93.51, refer to the technical data of 38 Series.
• 2 A, 24 V DC output
switching
• PCB or 93 series sockets
• 0.1 A, 48 V DC output
switching
• PCB or 93 series sockets
•
2 A, 240 V AC output switching
• Zero crossing switching
• PCB or 93 series sockets
Features
Ultra-slim - Solid State Relays
Printed circuit mount
- direct or via PCB socket
35 mm rail mount
- via screw or screwless sockets
• Single circuit output switching options
- 2 A 24 V DC
- 0.1 A 48 V DC
- 2 A 240 V AC
• Silent, high speed switching with long
electrical life
• Ultra slim, 5 mm, package
• Sensitive DC Input circuits (Dual AC/DC
input drive possible using 93 series sockets)
• UL Listing (certain relay/socket combinations)
• Wash tight: RT III
• 2,500 V insulation, input-output
input output
28
5
15.53.6
0.711
A2- A1+ + A
1.3
1.3
3.75
16.25
5
28
A2- A1+ + A
1.3
5
1.3
3.75
1.9
16.25
A2- A1+
1.3
5
5
28
1.3
1.9
3.75
16.25
28
~ ~
5
5
1.9
Example: 34 series slim electromechanical relay, 1 CO (SPDT) 6 A contacts, 24 V sensitive DC coil.
Example: 34 series SSR relay, 2 A output, 24 V DC supply.
34 Series - Ultra-Slim PCB relays
A: Contact material
0 = Standard AgNi
4 = AgSnO
2
5 = AgNi + Au (5 µm)
B: Contact circuit
0 = CO (SPDT)
3 = NO (SPST)
Series
Type
5 = Electromechanical type
No. of poles
1 = 1 pole, 6 A
Coil version
7 = Sensitive DC
Coil voltage
See coil specifications
5 1 07
D: Special versions
0 = Flux proof (RT II)
9 = Flat version
C: Options
1 = None
Ordering information
Electromechanical relay (EMR)
Solid state r
elay (SSR)
ABCD
... .
02434
Output circuit
9024 = 2 A - 24 V DC
7048 = 0.1 A - 48 V DC
8240 = 2 A - 240 V AC
Series
Type
8 = SSR type
Output
1 = 1 NO (SPST-NO)
Input circuit
See input specifications
8 1 7
... .
024
9024
34
Option = 34.51.7xxx.x019
Copper side view
0 1 0
3
Type Coil version A B C D
34.51 sens. DC 0 - 4 - 5 0 - 3 10
34.51 sens. DC 0 - 4 - 5 0 1 9
Selecting features and options: only combinations in the same row are possible.
Preferred selections for best avaliability are shown in bold.
Flat pack version
15
28 5
0.4 1
0.4
15.6
7.5
28
15.6
Ø 1.1 Ø 0.6
3.75
11.25 5 5 1.9
Technical data
34 Series - Ultra-Slim PCB relays
Nominal Coil Operating range Resistance Rated coil
voltage code
consumption
U
N
U
min
U
max
R I at U
N
VVVΩ mA
5 7.005 3.5 7.5 130 38.4
12 7.012 8.4 18 840 14.2
24 7.024 16.8 36 3,350 7.1
48 7.048 33.6 72 12,300 3.9
60 7.060 42 90 19,700 3
DC coil data
Coil specifications
• When switching a resistive load (DC1) having voltage and current
values under the curve, an electrical life of ≥ 60·103can be expected.
• In the case of DC13 loads, the connection of a diode in parallel with
the load will permit a similar electrical life as for a DC1 load.
Note: the release time for the load will be increased.
Electromechanical relay
4
Contact specification
F 34 - Electrical life (AC) v contact current
Cycles
DC voltage (V)
DC breaking current (A)
H 34 - Maximum DC1 breaking capacity
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
R 34 - DC coil operating range v ambient temperature
Insulation according to EN 61810-1:2004
Nominal voltage of supply system V AC 230/400
Rated insulation voltage V AC 250 400
Pollution degree 3 2
Insulation between coil and contact set
Type of insulation Reinforced
Overvoltage category III
Rated impulse voltage kV (1.2/50 µs) 6
Dielectric strength V AC 4,000
Insulation between open contacts
Type of disconnection Micro-disconnection
Dielectric strength V AC/kV (1.2/50 µs) 1,000/1.5
Conducted disturbance immunity
Burst (5...50)ns, 5 kHz, on A1 - A2 EN 61000-4-4 level 4 (4 kV)
Surge (1.2/50 µs) on A1 - A2 (differential mode) EN 61000-4-5 level 3 (2 kV)
Other data
Bounce time: NO/NC ms 1/6
Vibration resistance (5…55)Hz: NO/NC g 10/5
Shock resistance g 20/14
Power lost to the environment without contact current W 0.2
with rated current W 0.5
Recommended distance between relays mounted on PCB mm ≥ 5
Resistive load - cosϕ = 1
Inductive load - cosϕ = 0.4
7
10
10
10
10
6
5
4
0
4
62
(A)
20
10
6
4
2
1
0.2
8
0.1
20 60
100 140 180 220
U
2.0
U
N
1
1.5
1.0
0.5
-20
04020
60
2
80
(°C)
5
34 Series - Ultra-Slim PCB relays
Solid state relay
Nominal Input Operating range Release Impedance Control
voltage code voltage current
U
N
U
min
U
max
I at U
N
VVVVΩ mA
5 7.005 3.5 12 (10*) 1
715 (416*)
7 (12*)
24 7.024 16 30 10 3,200 7
60 7.060 35 72 20 21,300 3
Input data - DC types
Input specification
Output specification
Output current
Other data
Power lost to the environment without output current W 0.17
with rated current W 0.4
Technical data
Output current
L 34 - Output current v ambient temperature
SSR - 2 A DC & AC output types
L 34 - Output current v ambient temperature
SSR - 0.1 A DC output types
* AC Output version.
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.5
0.0
20 40 60-20 100800
(°C)
0.15
0.10
0.05
0
20 40 60-20 100800
(°C)
93 Series - Sockets and accessories for 34 series relays
93.01
6
Approvals
(according to type):
Screw terminal socket 35 mm (EN 50022) mounting
Supply voltage Relay type Socket type
12 V AC/DC 34.51.7.012.xx10 93.01.0.024
24 V AC/DC 34.51.7.024.xx10 93.01.0.024
48 V AC/DC 34.51.7.048.xx10 93.01.0.060
60 V AC/DC 34.51.7.060.xx10 93.01.0.060
(110…125)V AC/DC 34.51.7.060.xx10 or 34.81.7.060.xxxx 93.01.0.125
(220…240)V AC/DC 34.51.7.060.xx10 or 34.81.7.060.xxxx 93.01.0.240
(110…125)V AC/DC* 34.51.7.060.xx10 or 34.81.7.060.xxxx 93.01.3.125*
(220…240)V AC* 34.51.7.060.xx10 or 34.81.7.060.xxxx 93.01.3.240*
(220…240)V AC 34.51.7.060.xx10 or 34.81.7.060.xxxx 93.01.8.240
6 V DC 34.51.7.005.xx10 or 34.81.7.005.xxxx 93.01.7.024
12 V DC 34.51.7.012.xx10 93.01.7.024
24 V DC 34.51.7.024.xx10 or 34.81.7.024.xxxx 93.01.7.024
48 V DC 34.51.7.048.xx10 93.01.7.060
60 V DC 34.51.7.060.xx10 or 34.81.7.060.xxxx 93.01.7.060
Accessories
20-way jumper link 093.20 (see specification next page)
Plastic separator 093.01 (see specification next page)
Sheet of marker tags 093.64 (see specification next page)
Technical data
Rated values 6A - 250 V
Insulation 6 kV (1.2/50 µs) between coil and contacts
Protection category IP 20
Ambient temperature (–40…+70)°C (UN≤ 60 V), (–40…+55)°C (UN≥ 60 V)
Screw torque Nm 0.5
Wire strip length mm 10
Max. wire size for 93.01 socket solid wire stranded wire
mm21x2.5 / 2x1.5 1x2.5 / 2x1.5
AWG 1x14 / 2x16 1x14 / 2x16
* Leakage current suppression.
Certain relay/socket
combinations
75.6
87.3
6.2
7
93.51
Screwless terminal socket 35 mm (EN 50022) mounting
Supply voltage Relay type Socket type
12 V AC/DC 34.51.7.012.xx10 93.51.0.024
24 V AC/DC 34.51.7.024.xx10 93.51.0.024
(110…125)V AC/DC 34.51.7.060.xx10 or 34.81.7.060.xxxx 93.51.0.125
(220…240)V AC/DC 34.51.7.060.xx10 or 34.81.7.060.xxxx 93.51.0.240
(110…125)V AC/DC* 34.51.7.060.xx10 or 34.81.7.060.xxxx 93.51.3.125*
(220…240)V AC* 34.51.7.060.xx10 or 34.81.7.060.xxxx 93.51.3.240*
(220…240)V AC 34.51.7.060.xx10 or 34.81.7.060.xxxx 93.51.8.240
12 V DC 34.51.7.012.xx10 93.51.7.024
24 V DC 34.51.7.024.xx10 or 34.81.7.024.xxxx 93.51.7.024
60 V DC 34.51.7.060.xx10 or 34.81.7.060.xxxx 93.51.7.060
Accessories
20-way jumper link 093.20 (see table below)
Plastic separator 093.01 (see table below)
Sheet of marker tags 093.64 (see table below)
Technical data
Rated values 6A - 250 V
Insulation 6 kV (1.2/50 µs) between coil and contacts
Protection category IP 20
Ambient temperature (–40…+70)°C (UN≤ 60 V), (–40…+55)°C (UN≥ 60 V)
Wire strip length mm 10
Max. wire size for 93.51 socket solid wire stranded wire
mm21x2.5 1x2.5
AWG 1x14 1x14
* Leakage current suppression.
Approvals
(according to type):
093.20
20-way jumper link for 93.01 and 93.51 sockets 093.20 (blue) 093.20.0 (black)
Rated values 36 A - 250 V
093.01
093.64
Approvals
(according to type):
93 Series - Sockets and accessories for 34 series relays
Plastic separator for 93.01 and 93.51 sockets 093.01
Thickness 2 mm, required at the start and the end of a group of interfaces.
Can be used for visual separation of groups. Must be used for:
- protective separation of different voltages of neighbouring PLC interfaces according to VDE 0106-101
- protection of cut jumper links
Sheet of marker tags, plastic, 64 tags, 6x10 mm 093.64
for 93.01 and 93.51 sockets
Certain relay/socket
combinations
12
11
14
220-240
V~
A1
A2
75.6
93
6.2
2,5 mm
Accessories
121.5
2.8
10
6.5
6.2 6.26.26.26.26.26.26.26.26.2 1.851.85
16.5
93.11
Approvals
(according to type):
1.9
3.75
55
1.3
6.2
11.1
5.6
33
3.8
13
28.35
31
6.2
43.5
Copper side view
Retaining and release clip use:
PCB socket with retaining and release clip 93.11 (blue)
For relay type 34.51, 34.81
Technical data
Rated values 6 A - 250 V
Insulation ≥ 6 kV (1.2/50 µs) between coil and contacts
Protection category IP 20
Ambient temperature °C –40…+70
8
93 Series - Sockets and accessories for 34 series relays
(+) (A)
A2 A1 12 11 14
Loading...