Fimco LG-28-SS Assembly And Operating Instructions Manual
5301063
MODEL LG-28-SS
12 VOLT - 25 GALLON LAWN & GARDEN SPRAYER
Assembly / Operation Instructions / Parts
ASSEMBLY
The sprayer is partially assembled at the factory. The only
assembly necessary is to hook up the wiring to an existing
12 volt power source. The red wire of the two wire set must
be connected to the positive post on the battery or the “Hot”
connection on a switch or to the ammeter. The brown wire
may be grounded or connected to the negative battery post.
OPERA TION
The pump on the sprayer is equipped with a “on-off”toggle
switch and a pressure switch that is factory set at a maximum of 60 PSI. The handgun may be shut off at anytime
when the pump system is running and it will be electrically
turned off by the pressure switch. When the handgun trigger
is squeezed the pump will start again. Use care when hooking up the battery wires to the battery.
GENERAL INFORMATION
The purpose of this manual is to assist you in operating and
maintaining your lawn and garden sprayer. Please read it
carefully as it furnishes information which will help you
achieve years of dependable trouble free operation.
WARRANTY / PARTS / SERVICE
Products are warranted for one year from date of purchase
against manufacturer or workmanship defects.
Your authorized dealer is the best source of replacement
parts and service. T o obtain prompt, ef ficient service, always
remember to give the following information:
1. Correct part description and part number.
2. Model Number of your sprayer.
3. Serial Number of your sprayer.
Part description and part numbers can be obtained from the
illustrated parts list section of this manual.
Whenever you need parts or repair service, contact your
distributor / dealer first. For warranty work always take your
original sales slip, or other evidence of purchase date, to
your distributor / dealer.
The handgun has an adjustable nozzle which allows the spray
to be adjusted from a cone shaped fine mist to a straight
stream.
Note: The nut on the nozzle which has finger tabs must be
tight in order for the spray pattern adjustment to vary when
turning the nozzle end.
When it becomes necessary to clean the screen in the
suction line, remove the screen from the bottom of the
suction tube. Reach into the tank through the fill opening,
slide the tube to one side and slip the screen from the bottom of the tube. The screen may now be tapped or flushed
with clear water for cleaning.
WARNING: Some chemicals will damage the pump valves
if allowed to soak untreated for a length of time. Always flush
the pump with water after use. Do not allow chemicals to sit
in the pump for extended times of idleness. Flushing may be
done by adding 5 gallons of water to the tank and then pump
the solution through the entire system.
TECHNICAL SPECIFICATIONS
• Corrosion Resistant Polyethylene Tank
• 12 Volt Diaphragm Pump, Demand Switch
• 15 Foot Handgun Hose
1000 FIMCO LANE • P.O. BOX 1700 • NO. SIOUX CITY, SD 57049
Form No. 5004597 (816 7/05) Printed In U.S.A.
Page 1
AFTER SPRAYING
WINTER STORAGE
After use fill the sprayer part way with water, start the sprayer
and allow clear water to be pumped through the plumbing
system and out through the handgun. Use the handgun on
the sprayer to thoroughly wash all internal parts of the tank
and tank cover.
Refill the tank about half full with plain water and use a chemical neutralizer such as Nutra-Sol or equivalent and repeat
cleaning instructions above. Flush the entire sprayer with
the neutralizing agent. Follow the chemical manufacturers
disposal instructions of all wash or rinsing water.
Drain all water out of the sprayer paying special attention to
the pump, valves, and handgun. These items are
especially prone to damage from chemicals and freezing
weather. The sprayer should be winterized before storage
by pumping a solution of RV anti-freeze through the entire
plumbing. Proper care and maintenance will prolong life of
the sprayer.
Page 2
Loading...