Fimco 5302322, LG-3025-QR, ATV-25-71-QR, 5302321 Owner's Manual

OWNER’S MANUAL

Model: LG-3025-QR (5302322)

(25 Gallon Lawn & Garden/ATV Boomless Sprayer)

Technical Specifications

x 25 Gal. Corrosion-Resistant Polyethylene Tank
x 12 Volt Diaphragm Pump, 3.8 g.p.m.—45 psi
x Deluxe Pistol Grip Handgun
x 15 Ft. Handgun Hose (3/8” I.D.)
x 26 Ft. Vertical throw, 35 Ft. Horizontal Throw
x 30 Foot Spray Coverage w/Boom
x Corrosion-Resistant Nozzles

Caution: When fully filled with water, this sprayer will
weigh 260 lbs.. Consult the owner’s manual for your
vehicle to verify that you are within it’s load carrying
capacity.

Assembly Instructions

x Make sure the contents of the sprayer’s carton match the

items shown on page 2 of the manual.

x Follow the steps on pages 3 & 4 to properly assemble the

sprayer.

x After assembly is complete and before testing your spray-

er, make sure you connect the electrical hook-up to the
end of your pump and clip the clips to a fully charged bat­tery. The red wire must be connected to the positive (+)
and the black wire should be connected to the negative (-).

x The drain plug assembly should already be attached to the

tank

General Information

Thank you for purchasing this product. The purpose of this
manual is to assist you in operating and maintaining your lawn
& garden/ATV sprayer. Please read it carefully, as it furnishes
information which will help you achieve years of trouble-free
operation.

Warranty

Products are warranted for one year from date of purchase

against manufacturer or workmanship defects for home owner

www.fimcoindustries.com or call: TOLL FREE @ 1-800-831-0027

Our Technical Support Representatives will be happy to help you.

To obtain prompt, efficient service, always remember to give the

Part descriptions and numbers can be obtained from the illustrated

usage and 90 days for commercial usage.

For technical assistance, visit our website @

following information…

x Correct Part Description and/or part number

x Model #/Serial # of your sprayer

parts list section(s) of this manual.

***IMPORTANT REMINDER***

www.fimcoindustries.com

1000 FIMCO Lane, P.O. Box 1700, North Sioux City, SD 57049
Toll Free Phone: [phone] : Toll Free Fax: [phone]

[5008430 (04/16)]

Page 1

Contents of your sprayer’s carton (LG-3025-QR - 5302322):

Owner’s

Manual

Lid w/Lanyard

(#5058188)

Tank/Plumbing Pre-Assembly

“Wet Boom” Sub-Assembly

(5275712)

Contents of Parts Bag

#5278137

End Nozzle (5275122)

Pkg. of 2: #5275713

Contents of Bracket Kit

#5278138

Page 2

Step 1

Assembly Procedure (LG-3025-QR)

Normally, the sprayer will be mounted on an ATV with the
pump assembly at the operator’s back and the spray wand
will be at the rear of the unit. Right Hand (RH) and Left
Hand (LH) sides of the sprayer are
determined as if you are standing behind the sprayer,
looking at it (facing forward)

After removing the tank from the box, start the assembly
procedure by turning the tank upside down on a stable, flat
surface.

A phillips head screwdriver is required for this step.

(**) Mount tank brackets (5278222) to the underside of the
tank as shown in Step 1. Use (4) flat head screws
(5034149) to secure it to the tank. The tank will rest on the
surface of the brackets. Make sure the brackets are parallel
with each other before tightening down the bolts. Do not
over-tighten.

Step 2

Step 3

Detail A

After your tank brackets are securely attached, turn the
tank assembly over and position it so that the cam handles
which extend beyond the back of the tank are facing you
and just hanging over the edge of the table or flat surface
you are assembling this on.

Secure the boom mounting brackets (5038873) to the tank
mounting brackets with Cam handles as shown in Detail A.
You can position them as needed within the slot on the
bracket. Just be sure that the surfaces of both brackets are
even with each other.

You are now ready to mount this unit to an ATV, using
ratchet straps (NOT INCLUDED)

Attach the boom to the boom mounting brackets with
the (2) u-bolts and (4) whiz locknuts. Make sure the u­bolts are positioned within the grooves of the grommets
on the boom tube

NOTE: The purpose of these grommets is to pre­vent metal-to-metal contact between the u-bolts,
boom tube and boom mounting brackets.

The grommets will ‘compress’ as you tighten the whiz
locknuts onto the u-bolts. Tighten just so that the boom
tube will NOT rotate within the grommets. Alternate the
tightening of the locknuts to provide even pressure on
the grommet.

**DO NOT OVER TIGHTEN the whiz locknuts, as
this may cause the boom tube to flatten slightly!

Page 3