Fient Water Leak Detector Installation Manual

eng

Water Leak Detector

INSTALLATION MANUAL

Version 1.6

Product description

The Water Leak Detector provides you with an

early warning to help avoid or reduce potential

damage from leaking roofs, pipes, and

appliances, heavy rainfall, overland ooding, or

rapidly melting snow and ice.

The Water Leak Detector can be connected

with other Zigbee based products.

Precautions

• Do not remove the product label as it

contains important information.

• Do not paint the detector.

Getting started

1. Detach the cover of the detector by twisting
it counter clockwise.

a.

2. Insert one CR123A battery respecting the
polarities.

b.

3. Put the plastic disc back (it ts only one
way) and close the casing by twisting it
clockwise.

c.

4. The Water Leak Detector will start search-

ing (up to 15 minutes) for a Zigbee network

to join.

5. Make sure that the Zigbee network is open
for joining devices and will accept the
Water Leak Detector.

6. While the Water Leak Detector is searching
for a Zigbee network to join, the LED

ashes red.

d.

7. When the LED stops ashing, the Water
Leak Detector has successfully joined the
Zigbee network.

Placement

• Place the alarm indoors at a temperature
between 0-50°C.

• The Flood Sensor should be placed on the
ground, where water is suspected

• Reachable for the battery testing and
maintenance.

Testing

• Always test the working order of the Wa-

ter Leak Detector after installation or bat­tery change.

• When pressing the test button (closest to
the battery), the alarm sound should be
heard.

e.

• A network alarm test can be performed by
holding down the test button for at least

6.5 seconds (count 3 sounds).

• A test message will be sent
Zigbee network.

over the

Resetting

Resetting is needed if you want to connect your

Water Leak Detector to another gateway or if

you need to perform a factory reset to eliminate

abnormal behavior.

STEPS FOR RESETTING

1. Detach the cover of the detector by twisting
it counter clockwise.

2. Remove the plastic disc.

3. Press and hold the LED button.

f.

4. While you are holding the button down, the

LED rst ashes once, then two times in a

row, and nally numerous times in a row.

1. Release the button while the LED is

ashing numerous times in a row.

2. After you release the button, the LED

shows one long ash, and the reset is

completed.

Modes

SEARCHING GATEWAY MODE

The red LED inside of the device is ashing

every second (up to 15 minutes)

NORMAL MODE

The internal LED ashes red every 45 seconds.

ALARM MODE

The simultaneous ashing of the internal red

LED and sounding of intermittent audible
signal. When water is detected, the alarm will

sound. Press the “button/top” of the detector to

acknowledge and stop the siren. The following

10 minutes, it will block alarms.

g.

LOW BATTERY MODE

Simultaneous audible signals and LED ashes

every 45 seconds means that the battery

should be replaced.

Fault nding

• If the Water Leak Detector does not work

when the LED reset button is pushed, the

probable cause is a faulty battery. Replace

the battery if it is worn out.

• In case of a bad or weak signal, change

the location of the Water Leak Detector.

Otherwise, relocate your gateway or

strengthen the signal with a smart plug.

• If the search for a gateway has timed out, a

short press on the LED button will restart it.

Battery replacement

CAUTION: RISK OF EXPLOSION IF BATTERIES

ARE REPLACED BY AN INCORRECT
TYPE. DISPOSE OF THE BATTERIES IN
ACCORDANCE WITH INSTRUCTIONS.

CAUTION: When removing cover for battery

change - Electrostatic Discharge (ESD) can

harm electronic components inside

1. To replace the battery, detach the cover

of the Water Leak Detector by twisting it
counter clockwise.

2. Remove the plastic disc and replace the

battery respecting the polarities. The Water

Leak Detector uses 1xCR123 battery.

3. Put the plastic disc back and close the
casing by twisting it clockwise.

Disposal

Dispose the product and battery properly at

the end of life. This is electronic waste which

should be recycled.

FCC statement

FCC statement

Changes or modications to the equipment not

expressly approved by the party responsible for

compliance could void the user’s authority to

operate the equipment.

NOTE: This equipment has been tested and

found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is no

guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful

interference to radio or television reception,

which can be determined by turning the

equipment o and on, the user is encouraged

to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on
a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/

TV technician for help.

This device complies with FCC RF radiation

exposure limits set forth for an uncontrolled

environment. The antenna used for this

transmitter must be installed to provide a

separation distance of at least 20 cm from

all persons and must not be co-located or

operating in conjunction with any other antenna

or transmitter.

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful
interference, and

2. this device must accept any interference
received, including interference that may
cause undesired operation.

FCC Label can be found on the back of the

device when opening the cover by twisting it

counter clockwise.

IC statement

English

This device contains licence-exempt

transmitter(s)/receiver(s) that comply

with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two

conditions:

1. This device may not cause interference.

2. This device must accept any interference,

including interference that may cause

undesired operation of the device.

This equipment complies with IC RSS-102

radiation exposure limits set forth for an

uncontrolled environment. This equipment

should be installed and operated with minimum

distance 20 cm between the radiator and your

body.

Français

L’émetteur/récepteur exempt de licence

contenu dans le présent appareil est

conforme aux CNR d’Innovation, Sciences

et Développement économique Canada

applicables aux appareils radio exempts de

licence. L’exploitation est autorisée aux deux

conditions suivantes :

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage

est susceptible d’en compromettre le

fonctionnement.

Cet équipement est conforme aux limites

d’exposition aux radiations IC CNR-102 établies

pour un environnement non contrôlé. Cet

équipement doit être installé et utilisé avec une

distance minimale de 20 cm entre le radiateur

et votre corps.

ISED statement

ISED statement

Innovation, Science and Economic

Development Canada ICES-003 Compliance

Label: CAN ICES-3 (B)/NMB-3(B).

CE certication

The CE mark axed to this product conrms

its compliance with the European Directives

which apply to the product and, in particular,

its compliance with the harmonized standards

and specications.

IN ACCORDANCE WITH THE DIRECTIVES

• Radio Equipment Directive (RED)
2014/53/EU

• RoHS Directive 2015/863/EU amending
2011/65/EU

Other certications

• Zigbee 3.0 certied.

Installation of the probe

NOTE: The Water Leak Detector Probe is

an additional option for the Water Leak

Detector. It is only included on request.

1. Detach the detector from the probe base.

h.

2. Install the probe base on a wall by using
enclosed screws.

i.

NOTE: Make sure that the probe reaches

required level either to the oor or down the

drain.

j.

WALL

FLOOR

3. The detector can be attached to the base
simply by pushing it in there and rotating
until it you hear a click.

k.

Click!

All rights reserved.

frient assumes no responsibility for any errors,

which may appear in this manual. Furthermore,

Frient reserves the right to alter the hardware,

software, and/or specications detailed herein

at any time without notice, and frient does

not make any commitment to update the

information contained herein. All the trademarks

listed herein are owned by their respective

owners.

Distributed by frient A/S
Tangen 6
8200 Aarhus N
Denmark
www.frient.com

Copyright ©frient A/S

PN400062-1A 5102-007 (H6500161) v1.6