Fidelity Electronics DM-3000, DM-3000D, DM-6000, DM-6000D, DM-10K Operation Manual

...

DM SERIES

HIGH PRECISION WEIGHING SCALE

OPERATION MANUAL

PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE

ATTEMPT TO OPERATE THIS SCALE

V118 June 2012

Specifications subject to change without prior notice

CONTENTS

1. INSTALLATION

2. SPECIFICATIONS

3. KEYS, DISPLAY AND CONNECTIONS

4. GETTING STARTED

5. INITIAL SETUP

6. INSTRUCTION FOR USE

7. RS232 DATA OUTPUT MODE

8. TICKET / RECEIPT PRINTING

9. LABEL PRINTING (LP-50 or CPOMPATIBLE)

10. BATTERY POWER AND RECHARGING

11. ERROR CODES

12. DAILY CARE AND MAINTENANCE

Appendix A: -

BI-DIRECTIONAL COMMUNICATION COMMANDS

1. INSTALLATION

Because of metrological legislation, installation/some metrological parameter settings are limited to be done by authorized personnel only. Do not attempt to change any of the built-in parameters. Contact your dealer for installation and technical assistance.

CAUTION:

This scale is legal for trade only when it is sealed (and/or stamped) and bearing a serial number. Do not attempt to break the seal (or stamp) affixed to this scale or remove the serial number. Contact your dealer for more information and after sales service.

For most accurate weighing result, do not use the unit in where or when the environment condition falls beyond as those listed on SPECIFICATIONS.

Do not attempt to open this scale or conduct any trouble shootings other than those listed on TROUBLE SHOOTING.

2. SPECIFICATIONS

Model

Capacity [Max (g)]

Readability [d (g)]

DM-3000

3000

Nil

0.1

Nil

DM-3000D

1500

3000

0.1

0.2

DM-6000

6000

Nil

0.1

Nil

DM-6000D

3000

6000

0.1

0.2

DM-10K

10000

Nil

0.1

Nil

DM-10KD

5000

10000

0.1

0.2

DM-20K

20000

Nil

0.1

Nil

DM-20KD

10000

20000

0.1

0.2

Weight Units

kg / g / lb (Weight Unit Conversation Supports

Single Range Models only)

Tare Range

- Max (Subtractive Tare)

Platter

220 x 290mm all Stainless Steel

Dual Power Source

Built-in Rechargeable Battery, and

DC External Power Adaptor

Operation Environment

15 ~ 35oC. Non-condensed. R.H.≦ 85%

Specifications subject to change prior to notice

3. KEYS, DISPLAY AND CONNECTIONS

1. SPARE

Spare key, no assignment.

2. UNIT KEY

Press this key to shift among various weight units (if weight unit conversation is enabled).

3. PRINT KEY1

Press this key to print the results to a computer or a printer through the RS-232 output.

4. MR KEY

Press this key to recall total stored transactions.

5. M+ KEY

Press this key to accumulate current weight to memory manually.

6. ZERO KEY

Press this key to set weight displayed to zero when an empty scale has drifted away from a true zero reading.

7. TARE KEY

Press this key to tare off the weight of a container.

8. FUNCTION KEY

Press this key to shift between percentage, piece count and animal2 mode.

9. CHECK FUNCTION

Press this key to start check weighing function and to enter value for HI and LO limit.

10. CE KEY Press this key to clear value entered.

This key is also used to accumulate the current weight value to memory when F17 is set to

ON.

When F11 = ON.

11. NUMERIC KEYS

Numeric keys 0 ~ 9.

12. CHECK SYMBOLS

 HI = Checked Value is higher than the HI limit entered,  OK = Checked Value is in between than the low and HI limits entered,  LO = Checked Value is lower than the LO limit entered.

13. W1 INDICATOR3

(When under dual weighing range mode4) Visible when this scale is in the first weighing range (W1).

14. W2 INDICATOR5

(When under dual weighing range mode) Visible when this this scale is in the second weighing range (W2).

15. SPARE

Blank, no function assigned.

16. M+ INDICATOR

Visible when the total accumulated weight value is being displayed.

17. BATTERY POWER / LEVEL INDICATOR

Visible to show: -

 This scale is being powered by the built-in rechargeable battery,  Remaining battery level.

18. HOLD INDICATOR

(When under animal mode) Visible when weight reading being displayed is a frozen value.

This indicator will not appear when this instrument is in single range mode.

This instrument can support two weighing ranges with different maximum capacities (Max)

and different scale intervals (d), each range extending from zero to its maximum capacity.

This indicator will not appear when thus unit is in single range mode.

19. AUTO INDICATOR Visible when this scale is in animal weighing function.

20. NET INDICATOR

Visible when the tare function is in effect. Weight reading shown is net value.

21. GROSS INDICATOR

Visible when gross weight reading is displayed.

22. STABLE INDICATOR

This indicator appears to indicate the weight detected is in stable condition.

23. ZERO INDICATOR

Visible when this scale is at true zero weight status.

24. CAPACITY TRACK BAR

The ratio (increment = 10%) of applied & remaining weighing capacities are shown here.

25. WEIGHT UNITS AND FUNCTIONS

 % = Percentage (when in Percentage Mode in function),  kg = kilogram,  PCS = Pieces (Piece Count Mode in function),  kg/PCS and g/PCS = Weight per piece (Piece Count Mode in

function),

 lb = pound.

26. CHARGE STATUS INDICATOR

 Red color: Recharging battery,

 Green color: Charging completed.

BOTTOM VIEW

A. ON/OFF KEY Press this key to turn this scale on or off.

B. DC JACK INPUT

External power adaptor is plugged in here. Output requirements of the power adaptor: -

 DC9 ~ 12V 800mA,  Polarity: - Any kind.

C. RS232 COMPORT (DB9)

RS232 communication comport.

4. GETTING STARTED

In order to obtain an accurate weighing result, this scale must be placed on a strong and level surface. Avoid using this scale in environment where excessive wind flow, vibration and extreme temperature change exist

General Warning: -

 This scale is not an explosion proof device.  This scale is not a water proof device.  Do not open this scale, no user serviceable parts inside. Always

contact your dealer for service.

 This scale not to be subject to shock, excessive vibration or

extremes of temperature (before or after installation).

4.1 BUILT-IN RECHARGEABLE BATTERY

This scale is equipped with a built-in rechargeable battery. Before first time use, recharge it for at least 8 hours to ensure the best battery performance.

4.2 POWER ADAPTOR

Before plugging in the power adaptor, check and make sure the input voltage of the adaptor matches with output voltage of the electricity outlet. If not, contact your dealer immediately.

4.3 CONNECTING OTHER DEVICES6

4.3.1 Before Connecting with others

Turn this scale off and cut off power before making any connections or disconnections.

Turn this instrument off before making any connections or disconnections.

4.3.2. Connecting RS232 to computer

RS232 COMPORT

COM PORT ON COMPUTER

(DB9)

(DB25)

2 = RXD

3 = TXD

2 = RXD

5 = GND

7 = GND

4.3.3 Connecting RS232 to Printer (DB25)

RS232 COMPORT (DB9) ON

SCALE

COMPUTER COM DB25

2 = RXD

3 = TXD

2 = RXD

5 = GND

7 = GND

4.4 SETTING UP THE PREFERRED OPERATION PARAMETERS Set all preferred operation parameters according to 5.4 INTERNAL FUNCTION TABLE.

NOTE: -

1. F1~F26 are accessible without restriction,

2. F60~F66 are restricted functions which may request a password or hardware key to access,

3. F80 ~ F99 are restricted functions which may request a password or hardware key to access. These functions are usually for dealer and authorized personnel only and all settings these functions are monitored and recorded. Do not change any setting of these functions to avoid operation errors.

5. INITIAL SETUP

5.1 INTERNAL SETTINGS

Application parameters can be checked or set through internal setting functions. Refer to 5.4 for description of all internal functions.

5.2 HOW TO ENTER AND SELECT INTERNAL FUNCTION

Follow the below steps to enter and select desired parameter of an internal function.

a. Turn this scale off and on again, b. Press [TARE] during countdown, c. Display F1, d. This scale is now in internal function, e. Quick access to a function number

 Press 1 to go to F10,  Press 2 to go to F20,  Press 6 to go to F60 (for dealer and authorized personnel only),  Press 8 to go to F80 (for dealer and authorized personnel only),  Press 9 to go to F99 (for dealer and authorized personnel only),  Press 0 to go to F1,

5.3 KEY FUNCTION DURING INTERNAL FUNCTION MODE

 [M+] = Enter, save and return,  [ZERO] = Quit without saving,  [FUN] = Go next,  [UNIT] = Go previous,  [CE] = Clear,  [TARE] = Go to internal function during power on countdown, or set

F1 value being shown to zero and to display the net span gain by applying additional load applied.

+ 36 hidden pages

Fidelity Electronics DM-3000, DM-3000D, DM-6000, DM-6000D, DM-10K Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual