FIC P4M-865P Ultra, P4M-865PE Ultra, P4M-865PE MAX, P4M-865G Ultra User Manual

865 Dynasty

MAINBOARD

MANUAL

P4M-865G MAX

P4M-865PE MAX

P4M-865G Ultra

P4M-865PE Ultra

P4M-865P Ultra

DOC No.: M03106
Rev. : A0
Date : 5, 2003
Part No. : 25-10655-00

Notice

Handling Precautions

Warning:

1. Static electricity may cause damage to the integrated circuits on

the motherboard. Before handling any motherboard outside of its
protective packaging, ensure that there is no static electric charge
in your body.

2. There is a danger of explosion if the battery is incorrectly
replaced. Replace only with the same or an equivalent type
recommended by the manufacturer.

3. Discard used batteries according to the manufacturer’s
instructions.

4. Never run the processor without the heatsink properly and firmly

attached. PERMANENT DAMAGE WILL RESULT!

Observe the following basic precautions when handling the motherboard
or other computer components:

 Wear a static wrist strap which fits around your wrist and is

connected to a natural earth ground.

 Touch a grounded or anti-static surface or a metal fixture such as a

water pipe.

 Avoid contacting the components on add-on cards, motherboards,

and modules with the golden fingers connectors plugged into the
expansion slot. It is best to handle system components by their
mounting brackets.

The above methods prevent static build-up and cause it to be discharged
properly.

Trademark

All trademarks mentioned in this manual are registered properly of
the respective owners.

Handling Precautions

This manual may not, in whole or in part, be photocopied, reproduced,
transcribed, translated, or transmitted in whatever form without the
written consent of the manufacturer, except for copies retained by the
purchaser for personal archival purposes.

Ta ble of Contents

Table of Contents

Chapter 1 Overview

Package Checklist .......................................................................... 1-2

P4M-865G MAX
P4M-865PE MAX
P4M-865G Ultra

P4M-865PE Ultra

P4M-865P Ultra ......................................................................... 1-3

Main Features ................................................................................ 1-4

FIC Unique Innovation for Users (NOVUS) -

Enhanced Mainboard Features and System Support .................... 1-6

Chapter 2 Installation Procedures

1). Set System Jumpers .................................................................. 2-2

Clear CMOS ...................................................................... 2-2

BIOS Protect ...................................................................... 2-3

2). Install Memory Modules .......................................................... 2-4

3). Install the CPU .......................................................................... 2-5

Connect ATX Power .......................................................... 2-6

4). Install Expansion Cards ............................................................. 2-7

5). Connect Devices ....................................................................... 2-9

Floppy Diskette Drive Connector ...................................... 2-9

IDE Device Connectors ..................................................... 2-9

Fan Connectors ................................................................. 2-10

Power Connectors ............................................................. 2-10

Front Panel Block, Power LED, IR, and Speaker Connector 2-11

SIRQ Connector ................................................................ 2-12

Serial ATA Connectors ...................................................... 2-13

CD Audio-In Connector .................................................... 2-14

1394 Connectors (optional) ............................................... 2-14

PS/2 Keyboard and Mouse Connector .............................. 2-15

RJ45 LAN Connector ........................................................ 2-15

Serial Port Connectors ....................................................... 2-16

Printer Connector .............................................................. 2-16

i

865 D y n asty M ainboard M anual

Audio I/O Jacks ................................................................ 2-17

Front Audio Connector ..................................................... 2-17

CRT Connector .................................................................. 2-18

Universal Serial Bus Connectors ....................................... 2-18

Chapter 3 BIOS Setup

CMOS Setup Utility ....................................................................... 3-1

Standard CMOS Setup ................................................................... 3-2

Advanced BIOS Features .............................................................. 3-4

Advanced Chipset Features .......................................................... 3-8

Integrated Peripherals .................................................................... 3-10

Power Management Setup ............................................................. 3-14

PnP/PCI Configurations ................................................................. 3-18

PC Health Status ............................................................................ 3-19

Frequency/Voltage Control ............................................................ 3-20

Load Fail-Safe Defaults .................................................................. 3-21

Load Optimized Defaults ................................................................ 3-21

Supervisor/User Password ............................................................ 3-21

Save and Exit Setup ........................................................................ 3-22

Exit without Saving ........................................................................ 3-22

ii

865 Dynasty

®

Pentium 4 with

NOTE:

The information in this
document are subject to
change without further
notice.

Part Number: 25-10655-40

EZ Guide

Intel 865 Series

Package Checklist

 Mainboard | Manual | 865 Dynasty EZ Guide
 FDD cable  Drivers CD  ATA-100 cable
 I/O shielding |  USB cable

 Serial ATA cable (optional)
 1394 bracket with cable (optional)

Before Start

Warning:

1. Static electricity may cause damage to the integrated cir-

cuits on the motherboard. Before handling any motherboard
outside of its protective packaging, ensure that there is no
static electric charge in your body.

2. There is a danger of explosion if the battery is incorrectly
replaced. Replace only with the same or an equivalent type
recommended by the manufacturer.

3. Discard used batteries according to the manufacturer’s
instructions.

4. Never run the processor without the heatsink properly and
firmly attached. PERMANENT DAMAGE WILL RESULT!

Intallation Procedures

1. Install CPU 7. Set jumpers

2. Install memory module 8. Assembly case

3. Install mainboard 9. Link peripherals

4. Install devices 10. BIOS setup

5. Install add-on card 11. Install Drivers

6. Cconnect cables

Step 1 - Install CPU

1. Swing the lever upword to 90 degree.

2. Install the CPU and make sure the the pin 1

orientation by aligning the socket corner marking
with the socket corner closest to the lever tip.
Do not insert the CPU by force. Make sure the
processor is fully inserted into the socket on all
sides.

Apply some thermal materials, such as paste or

tape, on the CPU top; and install a fan with

heatsink that approved by CPU manufacturer

to avoid CPU damage. For detail information,

please refer to the CPU manufacturer website.

Affix the CPU by pressing the lever downward
and locking it beside the socket.

3. Place the fan with heatsink on the CPU top and
press down two plastic clips to hook up with the
holes on the retention module on two sides.

4. Press down the white bar on each clip to fasten
the fan set on the retention module.

Step 2 - Install Memory Module

Step 2 - Install Memory Module

1. Locate DDR DIMM sockets on the
mainboard.

2. Install DDR DIMM straight down
into the socket 1 using both hands,
then socket 2, and so forth.

3. The clip on both ends of the

socket will close up to hold the
DDR DIMM in place when the DDR
DIMM reaches the socket bottom.

NOTE:

1. To enable dual channel, it must be-

same density (128/256MB, etc.); same technology (128/256Mb, etc.);
same bus width (x8, x16); both single- (or dual-) sided; installed on
symmetical memory slots.

2. If your system uses an 800MHz CPU with DDR333 memory, the
memory interface of the chipset will runs at 320MHz.

Step 3 - Install Mainboard

Warning:

1. Excessive torque may damage the mainboard. When using

an electric screwdriver on the mainboard, make sure that the
torque is set to the allowable range of 5.0 ~ 8.0kg/cm.

2. Be aware of the shape edges in the case while installing
board.

1. Locate mounting holes on the

mainboard.

2. Place the board over the frame

inside the chassis.
Be sure that the board and frame are
aligned.

3. Affix the mainboard by copper

columns.

Front and Rear Panel

Note:

The chassis might not be the same as yours. The specifica­tion here is only for reference. Generally, most cases are simi­lar.

Step 4 - Install Devices

Floppy Drive

1. Locate floppy drive frame and

storage on the chassis.

2. Place the drive from the front

panel side into the frame.

3. Affix the drive on the frame by

screws.

4. Connect the floppy cable and power cable.

http://www.fic.com.tw

Step 4 - Install Devices (continued)

CD/DVD Drive

1. Locate CD/DVD drive frame and

storage on the chassis.

2. Place the drive from the front

panel side into the frame.

3. Affix the drive on the frame by

screws.

4. Connect the IDE cable and power cable.

Step 4 - Install Devices

Hard Disk Drive

1. Locate hard drive frame and

storage on the chassis.

2. Place the hard disk drive from the

rear of the frame as the arroaw head
indciated.

3. Affix the drive on the frame by

screws.

4. Connect the IDE cable and power cable.

Step 5 - Install Add-on Card

Warning:

Make sure to unplug the power supply when adding or remov­ing expansion cards or other system components. Failure to
do so may cause severe damage to both the mainboard and
expansion cards.

1. Select an available expansion slot.

2. Remove the corresponding slot

cover from the computer chassis. Un­screw the mounting screw that secures
the slot cover and pull the slot cover
out from the computer chassis. Keep
the slot cover mounting screw nearby.

3. Push the card firmly into the slot.

Push down on one end of the expan­sion card, then the other. Use this rock­ing motion until them card is firmly
seated inside the expansion slot. Se­cure the card with the screw removed
in Step 2.

Step 6 - Connect Wires

USB

Use the USB bracket with cable to install it on the rear panel. The pin defini­tions of the USB pinheaders (positions in the white rectangle in the below
right figure) are shown in the table below:

ATX Power

The 20-hole power plug (top right) is
connected to the ATX power 20-pin
pinheaders. The 4-hole 12V power plug
is inserted in the ATX_12V power con­nector. The plug from the power supply
will only insert in one orientation be­cause of the different hole sizes. Find
the proper orientation and push down
firmly making sure that the pins are
aligned.

Step 6 (continued)

Serial ATA

Use the optional SATA cable to con­nect to the hard drives (lower one is a
SATA data cable) and link with the
power supply (upper one is a SATA
power cable).

The pin definitions of the SATA
pinheaders (positions in the white rect­angle in the right figure)
are shown in the
right table:

1394 (optional)

Please use the optional 1394 cable to
install the 1394 connection.

The pin definitions
of the pinheaders
(positions in the
white rectangle in
the right figure)
are shown in the
right table:

Step 7 - Set System Jumpers

Clear CMOS

Warning: Please disconnect
the ATX power cable before
set this jumper and connect
the ATX power cable after
clear CMOS.

BIOS Protect Enable

The jumper is used to make sure that
the system BIOS can boot up when it is
enabled (default setting).

Step 8 - Assembly Case

Place the cover on the chas-

sis and secure the screws on

the cover either by a screw

driver or by fingers to

tighten them up.

Step 9 - Link Peripherals

Link peripheral devices to your system via rear/front panel.

Step 10 - BIOS Setup

Standard CMOS Setup

Use the arrow keys to highlight
the item and then use PgUp or
PgDn keys to select the value
you want in each item.

Load Fail-Safe Defaults

This submenu is selected to di­agnose the problem after the
computer boots, if the computer
will not boot. These settings do
not give optimal performance.

Step 11 - Install Drivers

Drivers

Place your lst Utilities CD into
your CD Drive. The top menu will
appear on the screen. Select the
item Drivers to start the auto runn
ing feature.

Help

The item provides you with
some information about the fea­tures and drivers. Reading it will
be helpful on installation.

Software Bundle

The item provides you with some useful software tools to assist you to man­age your computer system.

http://www.fic.com.tw

Chapter 1

Overview

Overview

The new microATX, 478-pin 1stMainboard® supports a full range of the latest
generation Intel® Pentium® 4 processors. The leading edge Intel® chipset
was designed for coworking with Pentium
package based on the VRM 10.0 spec and 400/533/800 MHz.Built using the
leading edge technology the Intel Pentium® 4 processors provide a significant
performance over previous Pentium® III processors. Two DDR 266/333/400
SDRAM sockets allow for up to 2 GB memory capacity. Support for the Ultra
DMA/100 protocol and its high-speed interface further ensures that data trans­fer speeds are improved, especially for long sequential transfers required by
audio/visual applications.

The board features onboard audio and LAN function; also, the serial ATA
feature replaces the standard parallel ATA physical storage interface and al­lows future enhancements to the computing platform. It completely software
compatible with parallel ATA, requiring no mofication to your operating sys­tem. For more detail, please read the help file in the lst Utilities CD.

® 4 (up to 3.06 GHz) in the 478-pin

The 1stMainboard comes with a versatile range of I/O features such as 1 serial
port, 1 CRT port, 1 parallel port, 1 LAN, 2 optional IEEE 1394, 1 PS/2 mouse and
keyboard connector, 8 USB ports, 1 media connector (front audio, Line-in,
Line-out and Mic-in). In addition, the board is equipped with 2 dual channel
enhanced PCI bus master IDE connectors. Ample expansion is available
through 3 PCI and 1AGP to meet the requirement for enjoying the P4 CPU
benefits in internet applicatons, video/3D graphics performance, and so forth.

Other key features are Remote On/Off, Auto Power Failure Recovery, inte­grated temperature monitoring and system fan control. Included also is lst
Utilities CD with enhanced drivers and a few bundled soft-ware solutions.

1 - 1

865 D y n asty M ainboard Manual

Package Checklist

If you discover any item below was damaged or lost, please contact your
vendor.

1 - 2

NOTE: lst Utilities CD that contains patch files, onboard video/au­dio chip drivers, related online help and other useful information
can be found in your mainboard package.

Please install it right after your Windows operating system installa­tion is done.Place your lst Utility in the drive, an operating menu will

appears in your monitor. Please select Auto Installation. It will auto­matically detect which software tools (patch files, drivers) that the
mainboard needs. Press OK button to go through the whole instal­lation procedure in a very straight forward and easy way. It also
provides you with a custom way to select wanted patch files and
software drivers that for onboard chips use. The top menu of lst

Utilities lists all the functions that allowed by this board.

P4M-865G MAX
P4M-865PE MAX
P4M-865G Ultra
P4M-865PE Ultra
P4M-865P Ultra

Overview

1 - 3

865 D y n asty M ainboard Manual

Main Features



 CPU



Celeron 1.4 G to 2.4 GHz and up* (FSB 400)

2.0 to 2.8 GHz and up* (FSB 533) /

3.06 GHz and up* (FSB 800)
(*: not tested yet)



 Chipset



North Bridge: Intel® 865G/PE/P
South Bridge: Intel® ICH5



 Memory



2 memory sockets :
support 184-pin DDR 266/333/400 MHz
memory size totally upto 2 GHz



 Expansion Slots



AGP Slot : support 2.0 4X/8X (0.8 - 1.5V);
3 PCI Slots



 IDE Connections



2 IDE connectors - PIO mode, Ultra DMA 66/100
up to 4 devices



 SATA Connections



2 ports controlled by embeded ICH5® SATA function



 Audio Features



AD1980 controller
AC97 2.2 compliant
LINE_IN, LINE_OUT, MICROPHONE_IN Jack
front audio pinheaders

1 - 4



 I/O Ports



2 IDE connectors ­PIO, Bus Master, Ultra DMA 66/100
up to 4 devices
1 serial port COM1
1 parallel port; 1 CRT port
PS/2 mouse and PS/2 keyboard
8 USB 1.1/2.0 ports



 LAN



RTL 8100BL®





IEEE 1394 Ports (optional)



Agere FW323
2 ports
1 bracket with cable



 Mounting Holes



9 holes



 Mainboard Size



9.6 x 9 (unit: inch)

Overview

1 - 5

865 D y n asty M ainboard Manual

FIC Unique Innovation for Users (NOVUS) -

Enhanced Mainboard Features and System Support



 LogoGenie



A user friendly GUI supporting Windows 95/98SE (not Windows 2000/
NT/ME/XP), LogoGenie allows you to customize, create or select a Logo
which will be displayed when the system is booting.

NOTE:

Please read Page 3-7 for detail information.



 BIOS Guardian



BIOS Guardian effectively acts as a fire-wall against viruses that can at­tack the BIOS while the system is running and by default is enabled.

WARNING:

BIOS Guardian must be disa bled bef ore refla s h BIOS.

NOTE:

Please read Page 3-7 for detail information.



 Easy Key



Instead of completing the multi-layered BIOS setup process these 3 Easy
Key functions provide direct access to Sub-Menu when completing BIOS
settings adjustments.

Easy-Keys are as follows:

Ctrl + c: To enter clock settings menu.

Ctrl + p: To load Performance Default settings and restart.
Ctrl + f: To load Fail-Safe Default settings and restart.

1 - 6

Installation Procedures

Chapter 2

Installation Procedures

The mainboard has several user-adjustable jumpers on the board that allow you to
configure your system to suit your requirements. This chapter contains information
on the various jumper settings on your mainboard.

To set up your computer, you must complete the following steps:

Step 1 - Set system jumpers

Step 2 - Install memory modules

Step 3 - Install the Central Processing Unit (CPU)

Step 4 - Install expansion cards

Step 5 - Connect ribbon cables, cabinet wires, and power supply

Step 6 - Set up BIOS software

Step 7 - Install supporting software tools

WARNING: Excessive torque may damage the mainboard. When
using an electric screwdriver on the mainboard, make sure that
the torque is set to the allowable range of 5.0 ~ 8.0kg/cm.

Mainboard components contain very delicate Integrated Circuit
(IC) chips. To prevent static electricity from harming any of the
sensitive components, you should follow the following precau­tions whenever working on the computer:

1. Unplug the computer when working on the inside.

2. Hold components by the edges and try not to touch the IC

||||chips, leads, or circuitry.

3. Wear an anti-static wrist strap which fits around the wrist.

4. Place components on a grounded anti-static pad or on the bag
that came with the component whenever the components are
separated from the system.

2 - 1

865 D y n asty M ainboard M anual

1). Set System Jumpers

Jumpers are used to select the operation modes for your system. Some jump­ers on the board have three metal pins with each pin representing a different
function. A 1 is written besides pin 1 on jumpers with three pins. To set a
jumper, a black cap containing metal contacts is placed over the jumper pin/s
according to the required configuration. A jumper is said to be shorted when
the black cap has been placed on one or two of its pins.

NOTE: Users are not encouraged to change the jumper settings
not listed in this manual. Changing the jumper settings improperly
may adversely affect system performance.

Clear CMOS

The CMOS RAM is powered by the onboard button cell battery. To
clear the RTC data:
(1) Turn off your computer;
(2) open the system case, disconnect the ATX power cable;
(3) place the jumper cap onto the pinpair 2-3 at least 6 seconds to enable
CMOS clearance;

(4) place the jumper cap onto the pinpair 1-2 to disable the effect of CMOS
clearance;
(5) connect the ATX power cable; close the system case;
(6) turn on your computer until CMOS checksum error appears;
(7) hold down the Delete key when boots;
(8) enter the BIOS Setup to re-enter user preferences.

2 - 2

Installation Procedures

BIOS Protect

The jumper helps users to prevent the 64K boot block table area in the
BIOS ROM from being overwritten by mistake.

2 - 3

865 D y n asty M ainboard M anual

2). Install Memory Modules

1. Locate DDR DIMM sockets

on the mainboard.

2. Install DDR DIMM straight down
into the socket 1 using both hands,
then socket 2, and so forth.

3. The clip on both ends of the

socket will close up to hold the
DDR DIMM in place when the DDR
DIMM reaches the socket bottom.

NOTE:

1. To enable dual channel, it must be-

same density (128/256MB, etc.); same technology (128/256Mb, etc.);
same bus width (x8, x16); both single- (or dual-) sided; installed on
symmetical memory slots.

2. If your system uses an 800MHz CPU with DDR333 memory, the
memory interface of the chipset will runs at 320MHz.

Press the clips with both hands to remove the DIMM.

2 - 4

Installation Procedures

3). Install the CPU

The mainboard has built-in Switching Voltage Regulator to support CPU Vcore
autodetection. That is, It has the ability to detect and recognize the CPU volt­age, clock, ratio.

The procedures below shows you how to install your CPU and its fan
and heatsink. First of all, locate the CPU socket on this mainboard.

1. Swing the lever upword to 90 degree.

2. Install the CPU and make sure the the pin 1

orientation by aligning the socket corner marking
with the socket corner closest to the lever tip.
Do not insert the CPU by force. Make sure the
processor is fully inserted into the socket on all
sides.

Apply some thermal materials, such as paste or

tape, on the CPU top; and install a fan with

heatsink that approved by CPU manufacturer

to avoid CPU damage. For detail information,

please refer to the CPU manufacturer website.

2 - 5

865 D y n asty M ainboard M anual

Affix the CPU by pressing the lever downward
and locking it beside the socket.

3. Place the fan with heatsink on the CPU top

and press down two plastic clips to hook up
with the holes on the retention module on two
sides.

4. Press down the white bar on each clip to

fasten the fan set on the retention module.

Connect ATX Power

The 20-hole power plug (top right) is connected
to the ATX power 20-pin pinheaders. The 4-hole
12V power plug (bottom right) is inserted in the
ATX_12V power connector.

The plug from the power supply will only insert
in one orientation because of the different hole
sizes. Find the proper orientation and push down
firmly making sure that the pins are aligned.

2 - 6

Installation Procedures

NOTE: Users The CPU installing procedures should be:

1. Insert the CPU (with its fansink and retention module) on the
socket.

2. Connect the 4-pin plug of the power supply

3. Connect the 20-pin plug of the power supply.
To remove the processor, please do it in reverse order.

4). Install Expansion Cards

This section describes how to connect an expansion card to one of your
system expansion slots.

Expansion cards are printed circuit boards that, when connected to the
mainboard, increase the capabilities of your system.

For example, expansion cards can provide video and sound capabilities. The
mainboard features one AGP and three PCI bus expansion slots.

CAUTION:

1.Make sure to unplug the power supply when adding or removing

expansion cards or other system components. Failure to do so
may cause severe damage to both the mainboard and expansion
cards.

2. Always observe static electricity precautions.

3. Please read Handling Precautions at the start of this manual.

2 - 7

865 D y n asty M ainboard M anual

1. Select an available expansion slot.

2. Remove the corresponding slot cover from the computer chassis. Un-

screw the mounting screw that secures the slot cover and pull the slot cover
out from the computer chassis. Keep the slot cover mounting screw nearby.

3. Push the card firmly into the slot.

Push down on one end of the expan­sion card, then the other. Use this rock­ing motion until them card is firmly
seated inside the expansion slot. Se­cure the card with the screw removed
in Step 2.

2 - 8

Installation Procedures

5). Connect Devices

Floppy Diskette Drive Connector

This connector provides the connection with your floppy disk drive.

Insert the floppy ribbon cable (below)
onto the floppy connector.

The colored stripe (indicated by the
arrow head, right) of the ribbon cable
must be the same side with the Pin 1.

IDE Device Connectors

The two connectors, IDE1 (PRIMARY)
and IDE2 (SECONDARY), are used for
your IDE hard disk drives, CD drives,
LS-120|drives, or IDE ZIP drives.

Insert the floppy ribbon cable (below)
onto the floppy connector.

The colored stripe (indicated by the
arrow head, right) of the ribbon cable
must be the same side with the Pin 1.

2 - 9

865 D y n asty M ainboard M anual

Fan Connectors

The two connectors, CPU_FAN, SYS_FAN are linked to the CPU fan, case fan,
respectively. CHIP_FAN can be used with North Bridge chip fan.

Power Connectors

The 20-pin male block connector is connected to the ATX power supply. The
4-pin male block connector is for the ATX_12V power use. All two connectors
are linked with your ATX power supply. The plug from the power supply will
only insert in one orientation because of the different hole sizes. Find the
proper orientation and push down firmly making sure that the pins are aligned.

2 - 10

Installation Procedures

Front Panel Block, Power LED, IR, and Speaker Connector

This block connector includes the connectors for linking with Power LED (3­pin), HDD LED, power button, power/sleep/message waiting button, reset
buttonon the front panel of the system case. Please identify polarities of plug
wires for the case speaker and LEDs. Please ask vendor about this information
when you buy them and install the system by yourself. The plug wires polari­ties of these buttons will not affect the function.

NOTE: Users that want to use IR port must adjust BIOS feature IR
Controller Port to activate onboard IR featuere.

(1) Reset Switch is connected to the reset button. Push this switch to reboot
the system instead of turning the power button off and on.

(2) HDD LED is connected to the IDE device indicator. This LED will blink
when the hard disk drives are activated.

(3) Power (Single and Dual) /Sleep LED

Please refer to the tables below for the representations of LED states.
There is another 3-Pin Power LED connector on board for some cases that with
a 3-pin plug.

2 - 11

865 D y n asty M ainboard M anual

(4) Power Button is connected with power button. Push this switch allows the
system to be turned on and off rather than using the power supply button.

IR is a pinheader that is used for linking with your ID device to allow transmis­sion of data to another system that also supports the IR feature. This mainboard
provides users with two types of IR pinheaders.

Speaker is connected with the case speaker.

Serial IRQ Connector

This 2-pin connector is used for some system integration use.

2 - 12

Installation Procedures

Serial ATA Connectors

The 2 SATA connectors (SATA1/2 are controlled by Intel ICH5R®) provide
you with the connections to serial ATA devices that confirm to the Serial ATA
specification. Serial ATA supports all ATA and ATAPI devices. The figures
below left are two SATA cables (the top one is for power; the next one is for
data). The data cable pin assignments of SATA connector.

NOTE: Please read page 3-12 for more detail about the usage of
SATA feature.

2 - 13

865 D y n asty M ainboard M anual

CD Audio-In Connectors

The connectors, CD_IN and AUX_IN, are for CD-ROM drive audio analog
input use.

1394 Connectors (optional)

The 2 optional 1394 pinheaders on the board provides you with two connec­tions with the peripherals which own 1394 connectors by an optional bracket
with cable (see the figure below). The pin definitions of the 1394 pinheaders
are listed below also.

2 - 14

Installation Procedures

PS/2 Keyboard and Mouse Connector

These two 6-pin female (PS/2 keyboard is purple color and PS/2 mouse is
green color) connectors are used for your PS/2 keyboard and PS/2 mouse.

RJ45 LAN Connector

The RJ45 jack of LAN port is used for the LAN cable plug.

2 - 15

865 D y n asty M ainboard M anual

Serial Port Connectors

COM1 (9-pin D-sub male connector with teal color) allows you to connect with
your devices that use serial ports, such as a serial mouse or an external modem.

Printer Connector

This 25-pin D-Sub female burgundy-colored connector is attached to your
printer.

2 - 16

Installation Procedures

Audio I/O Jacks

LINE_OUT (lime) can be connected to headphones or preferably powered
speakers. LINE_IN (light blue) allows tape players or other audio sources to
be recorded by your computer or played through the LINE_OUT. MIC_IN
(pink) allows microphones to be connected for audio input.

Front Audio Connector

The mainboard has a front panel
audio F_AUDIO connector
(Intel spec.). It allows users to
attach the audio device via front
panel (instead of rear panel) by a
ribbon cable that in some cases.
Its pin definitions are resented
below.

NOTE: If you do not use F_AUDIO, please keep the pinpair 5-6, 9-10
short as default; also, when the front headphone is plugged in,
the rear audio output will be disabled.

2 - 17

865 D y n asty M ainboard M anual

CRT Connector

The connector is linked with your monitor. The
pinheaders pin assignments are shown at right side.

Universal Serial Bus Connectors

The mainbaord have eight USB ports; four USB black jacks that integrated on
the edge of the board, the other four USB ports (pinheaders) on the board.
They allows users to attach with USB devices either from rear or front panels.
Please note that your operating system must support USB 1.1/2.0 features.

The figure below is the pin
assignments of the USB4/5 and
USB6/7.

2 - 18

BIOS Setup

Chapter 3

BIOS Setup

The mainboard comes with the chip that Award BIOS that contains the ROM
Setup information of your system. (This chip serves as an interface between
the processor and the rest of the mainboard components.) This section ex­plains the information contained in the Setup program and tells you how to
modify the settings according to your system configuration.

CMOS Setup Utility

The Setup utility program allows updates to the mainboard configuration set­tings. The BIOS setup values will be saved in the CMOS. It is executed when
the user changes system configuration; user changes system backup battery;
or the system detects a configuration error and asks the user to run the Setup
program. Use the arrow keys to select and press Enter to run the selected
program.

3 - 1

865 D y n asty M ainboard Manual

Standard CMOS Setup

The Standard CMOS Setup screen is displayed above. Each item may have
one or more option settings. The system BIOS automatically detects memory
size, thus no changes are necessary. Use the arrow keys to highlight the item
and then use PgUp or PgDn keys to select the value you want in each item.

Date

To set the date, highlight the Date field and then press Page Up/Page Down
or +/- keys to set the current date. Follow the month, day and year format.

Time

To set the time, highlight the Time field and then press Page Up/Page Down
or +/- keys to set the current time. Follow the hour, minute, and second
format.

3 - 2

BIOS Setup

Hard Disks

This field records the specifications for all non-SCSI hard drives installed
in the system. The onboard PCI IDE connectors provide Primary and Sec­ondary channels for connecting up to four IDE hard disks or other IDE
devices. Each channel can support up to two hard disks, the first of which
is the Master and the second is the Slave.

Hard Disk Configurations

Capacity: The hard disk size. The unit is Bytes.
Cylinder: The cylinder number of the hard disk.
Head: The read/write head number of hard disk.
Precomp: The cylinder number at which the disk drive

changes the write current.

Landing Zone: The cylinder number that the disk drive heads

(read/write) are seated when the disk drive is
parked.

Sector: The sector number of each track defined on the

hard disk.

Drive A / Drive B

This field records the types of floppy drives installed in the system. To
enter the configuration value for a particular drive, highlight its corre­sponding field and then select the drive type using the left- or right-arrow
key.

Floppy 3 Mode Support

This is a Japanese standard floppy type drive. The standard stores 1.2MB
in a 3.5 inch diskette.

Video

Set this field to the type of video display card installed in the system.

Halt On

This field determines which types of errors will cause the system to halt.

3 - 3

865 D y n asty M ainboard Manual

Advanced BIOS Features

Virus Warning

This feature starts the virus scan tool to detect if boot virus in boot sector
of the first hard disk drive when booting up.
The options are: Enabled, Disabled.

CPU L1 & L2 Cache

When enabled, improves the system performance. Disable this item when
testing or trouble-shooting. The options are: Enabled, Disabled.

Quick Power On Self Test

When enabled, allows the BIOS to bypass the extensive memory test.
The options are: Enabled, Disabled.

Hard Disk Boot Priority

This feature will auto detect all hard disks of bootable device on the sys­tem. It also allows users to select hard disk device booting priority.

First/Se cond/Third Boot Device

This feature allows user to select the boot device priority. The options are:
Floppy, LS120, Hard Disk, CDROM, ZIP100, USB-FDD, USB-ZIP, USB­CDROM, USB-HDD, LAN, Disabled.

3 - 4

BIOS Setup

Boot Other Device

This feature allows user to select the boot device priority.
The options are: Enabled, Disabled.

Swap Floppy Drive

Allows you to switch the order in which the operating system accesses
the floppy drives during boot up. Full Screen LOGO Show
It decides whether or not the full screen logo is shown during system
booting up. The options are: Enabled, Disabled.

Boot Up Floppy Seek

When enabled, assigns the BIOS to perform floppy diskette drive tests by
issuing the time-consuming seek commands.
The options are: Enabled, Disabled.

Boot Up Numlock Status

When set to On, allows the BIOS to automatically enable the Num Lock
Function when the system boots up. The options are: On, Off.

Gate A20 Option

When set at Fast, allows a faster access response under Protected mode.
The options are: Fast, Normal.

Type matic Rate Setting

The term typematic means that when a keyboard key is held down, the
character is repeatedly entered until the key is released.
The options are: Disabled, Enabled.

Type matic Rate (Chars/Se c)

This feature is available only if the above item, Typematic Rate Setting, is
set at Enabled. Sets the rate of a character repeat when the key is held
down. The options are: 6, 8, 10, 12, 15, 20, 24, 30.

T ype matic Delay (M sec)

This feature is available only if the item, Typematic Rate Setting, is set at
Enabled. Sets the delay time before a character is repeated.
The options are: 250, 500, 750, 1000 millisecond.

3 - 5

865 D y n asty M ainboard Manual

Security Option

Allows to set the security level of the system.The options: Setup, System.

APIC Mode

Allows you to decide if the system enters the APIC (Advanced Program­mable Interrupt Controller) mode or not for more IRQs can be released.
The options are: Enabled, Disabled.

MPS Version Control For OS

When two CPUs onboard (not this board) this feature allows you to select
MPS (Multi-Processor Spec.) version control for OS when logo test ex­ecutes. The options are: 1.1, 1.4.

OS Select For DRAM > 64MB

If your operating system (OS) is OS/2, select the option OS2. Otherwise,
stay with the default setting Non-OS2.The options are: Non-OS2, OS2.

H D D S.M.A.R.T. Capa bility

S.M.A.R.T. stands for Self-Monitoring and Analysis Reporting Technol­ogy which allows your hard disk drive to report any read/write errors and
issues a warning with LDCM installed. The options: Disabled, Enabled.

Report No FD D For W I N 95

When the field under the Standard CMOS Setup Menu for Drive A and/or
Drive B is set at None, users must set this field is set at Yes for it to function
properly. Otherwise, set at No, even if field for Drive A and/or Drive B is set
at None, system will still detect and recognize of a floppy drive(s).
The options are: Yes, No.

BIOS Guardian

It allows the system to prevent computer viruses. Users will need to dis­able it to update BIOS. The options are: Enabled, Disabled.

3 - 6

NOTE: Please disable this BIOS feature about BIOS Guardian
before you start to reflash BIOS.

BIOS Guardian and Reflash BIOS

BIOS Guardian by default is enabled, thus effectively acts as a fire­wall against viruses that can attack the BIOS while the system is
running. It must be disabled before reflash BIOS.

BIOS Setup

The steps below show you how to off and on BIOS Guardian when
reflash BIOS:

1. Press Del key while booting. Go to CMOS Setup Utility menu.

2. Go to Advanced BIOS Features submenu.

3. Set the feature BIOS Guardian at Disabled.

4. Save the setting and exit. The system restarts.

5. POST screen holds. A message about BIOS Guardian shows.

6. Press Space bar.

7. Reflash BIOS. Restart the system after complete it.

8. POST screen holds. A message about BIOS Guardian shows.

9. Press G key. The feature BIOS Guardian will be enabled again.

Full Screen LOGO Show

It decides whether or not the full screen logo is shown during system
booting up. The options are: Enabled, Disabled.

NOTE:

1. LogoGenie supports Award BIOS only.

2. If you create a Logo file (.bmp) by LogoGenie, the file size must

||||be 640 x 464 x 256 colors.

To enable this utility, please proceed as follows:

1. Insert software CD. Select LogoGenie from the Menu
and follow the installation instructions.

2. After LogoGenie has been installed, go to Windows Start Box.
In Programs Menu, select LogoGenie, then select LogoGenie.

3. Press F1 to read Help file to understand how to use this software if
it is new to you.

3 - 7

865 D y n asty M ainboard Manual

Advanced Chipset Features

DRAM Timing Selectable

This feature allows user to select the way to set DRAM timing.
The options are: Manual, By SPD.

CAS Latency Time

This feature allows user to select the CAS latency time, when any SDRAM
DIMM installed. The options are: 2, 2.5, 3.

Active to Precharge Delay

This feature allows user to set Active to Precharge Delay, if any SDRAM
installed. The options are: 8, 7, 6, 5.

D RAM RAS# to CAS# Delay

The feature allows user to set the delay time that from the DRAM RAS#
active to CAS#. The options are: 4, 3, 2.

DRAM RAS# Precharge

The feature allows user to set the DRAM RAS# Precharge Time.
The options are: 4, 3, 2.

Memory Frequency For

This feature allows users to set the memory frequency.
The options are: DDR 266, Auto.

3 - 8

BIOS Setup

Syste m BIOS Cacheable

Setting at Enabled will allow the caching of the BIOS ROM F0000H-FFFFFH,
resulting in better system performance. It may cause system error when
some programd try to access the memory area.
The options are: Disabled, Enabled.

V ideo BIOS Cache able

Setting at Enabled will allow the caching of the video BIOS ROM at C0000H­C7FFFH, resulting in better video performance. It may cause system error
when some programd try to access the memory area.
The options are: Disabled, Enabled.

Delay Prior to Thermal

It allows user to select the Delay Prior to Thermal.
The options are: 4 Min, 8 Min, 16 Min, 32 Min.

AGP Gr a phics Aperature Size (MB)

It allows user to select the main memory frame size of AGP use.
The options are: 4, 8, 16, 32, 64, 128, 256.

Init Display First

When you install an AGP VGA card and a PCI VGA card on the board, this
feature allows you to select the first initiation of the monitor display from
which card. The options are: PCI Slot, AGP.

** On-Chip VGA Setting ***

On-Chip VG A Setting

This feature allows users to disable the onchip VGA feature.
The options are: Enabled, Disabled.

On-Chip Frame Buffer Size

This feature allows users to select the onchip frame buffer size.
The options are: 1MB, 8MB, 16MB, 32MB.

Boot Display

This feature allows users to decide which monitor appears boot screen if
there are more than one type of monitor.
The options are: Auto, CRT, TV, EFP.

3 - 9

865 D y n asty M ainboard Manual

Integrated Peripherals

OnChip IDE Device

IDE HDD Block Mode

When enabled, the system executes read/write requests to hard disk in
block mode. The options are: Enabled, Disabled.

On-Chip Primary PCI IDE

When enabled, it allows you to use the onboard primary PCI IDE.
The options are: Enabled, Disabled.

IDE Primary Master/Slave PIO

Allows an automatic or a manual configuration of the PCI primary IDE
hard drive (master/slave) mode. The options are: Auto, Mode 0, Mode 1,
Mode 2, Mode 3, Mode 4.

IDE Pri mary Master/Slave UDMA

Allows an automatic configuration of the PCI primary IDE hard drive
(master/slave)) mode if Ultra DMA is supported both on the motherboard
and the hard disk. The options are: Auto, Disabled.

On-Chip Secondary PCI IDE

When enabled, it allows you to use the onboard secondary PCI IDE.
The options are: Enabled, Disabled.

3 - 10

BIOS Setup

IDE Secondary Master/Slave PIO

Allows an automatic or a manual configuration of the PCI secondary IDE
hard drive (master/slave) mode. The options are: Auto, Mode 0, Mode 1,
Mode 2, Mode 3, Mode 4.

IDE Secondary Master/Slave UDMA

Allows an automatic configuration of the PCI secondary IDE hard drive
(master/slave) mode if Ultra DMA is supported both on the motherboard
and the hard disk. The options are: Auto, Disabled.

Onboard Device

USB Controller

Disable this option if you are not using the onboard USB 1.1 and USB 2.0
feature. The options are: Disabled, Enabled.

USB 2.0 Controller

Disable this option if you are not using the onboard USB 2.0 feature (USB

1.1 not effected). The options are: Disabled, Enabled.

USB Legacy KB

When set at Auto, the BIOS will detect if USB keyboard is installed
automatically. The options are: Auto, Disabled, Enabled.

AC97 Audio

This feature auto detects if you use a card that with a CODEC to enable or
disable the AC97 audio function. The options are: Auto, Disabled.

Onboard 1394 Controller

This feature allows you to disable the onboard 1394 feature.
The options are: Enabled, Disabled.

Onboard Lan Controller

This feature allows users to enable or disable the onboard Lan controller.
The options are: Enabled, Disabled.

Onboard Lan Boot ROM

This feature allows users to enable or disable the onboard Lan boot
ROM to boot system. The options are: Enabled, Disabled.

3 - 11

865 D y n asty M ainboard Manual

*** Serial ATA Setting ***

Onboard Serial ATA

This feature allows users to disable the optional onboard SATA chip.
The options are: Enabled, Disabled.

S ATA Mode

This feature allows users to select SATA specifications that embeded func­tions in South Bridge. The options are: IDE, RAID.

On-Chip Seri al ATA

This feature allows users to select the SATA function modes (that embeded
in South Bridge). Setting at Disabled will disable STAT controller. Set at
Auto will allow the BIOS to arrange it. Setting Combined Mode will make
PATA and SATA combined. Max. of 2 IDE drives in each channel (primary
master/slave; secondary master/slave). Enhanced Mode allows max. of 6
IDE drives supported. SATA Only will make SATA operates in legacy mode.
The options are: Disabled, Auto, Combined Mode, Enhanced Mode, STAT
Only.

Seri al ATA Port0/1 Mode

This feature allows users to select the SATA port 0/1 modes.
The options are: SATA0 master, SATA1 master.

SuperIO Device

Onboard FDC Controller

When enabled, the floppy diskette drive (FDD) controller is activated.
The options are: Enabled, Disabled.

Onboard Serial Port 1

If the serial port 1 uses the onboard I/O controller, you can modify your
serial port parameters.
The options are: Disabled, 3F8/IRQ4, 3E8/IRQ4, 2E8/IRQ3.

IR Controller Port

Allows you to enable the IR function.

The options are: Enabled, Disabled.

3 - 12

BIOS Setup

UART Mode Select

Allows you to select the IR modes if the serial port 2 is used as an IR port.
Set at Standard, if you use COM2 as the serial port as the serial port,
instead as an IR port. The options are: Normal, IrDA, ASKIR, SCR.

UR2 Duplex Mode

Allows you to select the IR modes.
The options are: Full, Half.

Onboard Parallel Port

Allows you to select from a given set of parameters if the parallel port uses
the onboard I/O controller.
The options are: Disabled, 378/IRQ7, 278/IRQ5, 3BC/IRQ7.

Parallel Port Mode

Allows you to connect with an advanced printer via the port mode it
supports. The options are: SPP, ECP, EPP, EPP+ECP.

E C P Mode Use D M A

This feature allows you to select Direct Memory Access (DMA) channel.
The options are: 1, 3.

Power Management Setup

3 - 13

865 D y n asty M ainboard Manual

PWRON After PWR-Fail

When the system is shut down owing to the power failure, the system will
not be back to power on by itself. This feature allows you to set the
system back to which power status of the system when the system power
is resumed. The options are: Former-Sts, On, Off.

ACPI Function

This item allows you to disable the ACPI function.
The options are: Enabled, Disabled.

ACPI Suspend Type

This item allows you to select suspend mode when the system in ACPI
mode. The options are: S1 (POS), S3 (PTR), S1&S3.

Run VGABIOS if S3 Resume

This feature allows you to decide the way if VGA BIOS should be called
when the system resumes from S3 state if the above feature is set at S3
(PTR) or S1&S3. The options are Auto, Yes, No.

Power Management

This item allows you to adjust the power management features.
Select User Define for configuring your own power management features.
Min Saving initiates all predefined timers in their minimum values. Max
Saving, on the other hand, initiates maximum values.
The options are: User Define, Min Saving, Max Saving.

Video Off Method

The option Blank Screen allows the BIOS to blank off screen display by
turning off the red-green-blue signals. The option V/H SYNC+Blank al­lows the BIOS to blank off screen display by turning off the V-Sync and H­Sync signals sent from add-on VGA card. The option DPMS allows the
BIOS to blank off screen display by your add-on VGA card which sup­ports DPMS (Display Power Management Signaling function).
The options are: Blank Screen, V/H SYNC+Blank, DPMS.

Video Off In Suspend

The option allows you to select VGA status when the system goes to
suspend mode. The options are: No, Yes.

3 - 14

BIOS Setup

MODEM Use IRQ

This feature allows you to select the IRQ# to meet your modem IRQ#.
The options are: NA, 3, 4, 5, 7, 9, 10, 11.

Suspend Mode

When disabled, the system will not enter Suspend mode. The specified
time option defines the idle time the system takes before it enters Suspend
mode. The options are: Disable, 1, 2, 4, 8, 10, 20, 30, 40 Min, 1 Hour.

H D D Power Down

The option lets the BIOS turn the HDD motor off when system is in Sus­pend mode. Selecting 1 Min..15 Min allows you define the HDD idle time
before the HDD enters the Power Saving Mode.
The options 1 Min..15 Min will not work concurrently. When HDD is in the
Power Saving Mode, any access to the HDD will wake the HDD up.
The options are: Disabled, 1 Min..15 Min.

Soft-Of f b y PW R-BTTN

The selection Delay 4 Sec. will allow the system shut down after 4 seconds
after the power button is pressed. The selection Instant-Off will allow the
system shut down immediately once the power button is pressed.
The settings are: Instant-Off, Delay 4 Sec.

CPU THRM-Throttling

When thermal override condition occur, this item allows users to deter­mine the duty cycle of the throttling.
The options are: 87.5%, 75.0%, 62.5, 50.0%, 37.5%, 25.0%, 12.5%.

Wake-Up by PCI card

When set at Enabled, any PCI-PM event awakes the system from a PCI­PM controlled state. The options are Disabled, Enabled.

Power On by Ring

An incoming call via modem awakes the system from its soft-off mode.
The options are Disabled, Enabled.

USB KB Wake-Up From S3

When set at Enabled, it allows USB keyboard to activate the system from
ACPI S3 power saving mode. The options are Disabled, Enabled.

3 - 15

865 D y n asty M ainboard Manual

R e sume by Alarm

This feature allows you to set the when the system being turned on from
the system power-off status. The options are: Enabled, Disabled.

Date (of Month) Alarm

This feature allows you to set the day of the alarm starts when the RTC
Alarm Resume From Soft Off is set to be Enabled. The options are: 0, 1..31.

Time (hh:mm:ss) Alarm

If an ATX power supply is installed and when RTC Alarm Resume is En­abled, this feature allows you to set the time of the alarm starts when the
RTC Alarm Resume From Soft Off is set to be Enabled. The options are: hh
(hour) - 0, 1, 2,.., 23; mm (minute) - 0, 1, 2,..,59; ss (second) - 0, 1, 2,..,59.

Primary IDE 0

When the primary master HDD is working, the system timer will be re­loaded and the system will not be into the suspend mode.
The options are: Disabled , Enabled.

Primary IDE 1

When the primary slave HDD is working, the system timer will be reloaded
and the system will not be into the suspend mode.
The options are: Disabled, Enabled.

Secondary IDE 0

When the secondary master HDD is working, the system timer will be
reloaded and the system will not be into the suspend mode.
The options are: Disabled, Enabled.

Secondary IDE 1

When the secondar slave HDD is working, the system timer will be re­loaded and the system will not be into the suspend mode.
The options are: Disabled, Enabled.

FDD, COM, LPT Port

When FDD, COM, or LPT is working, the system timer will be reloaded and
the system will not be into the suspend mode.
The options are: Disabled, Enabled.

3 - 16

BIOS Setup

PCI PIRQ[A-D]#

When the PCI PIRQ[A-D]# has been alerted, the system timer will be re­loaded and the system will not be into the suspend mode.
The options are: Disabled, Enabled.

PnP/PCI Configurations

PNP OS Installed

If your operating system is a Plug-and-Play one, such as Windows NT,
Windows 95, select Yes. The options are: No, Yes.

Reset Configuration Data

Enabling it to reset the system Extended System Configuration Data (ESCD)
when you exit Setup if you have installed a new add-on card and the
system reconfiguration has caused such a serious conflict that the operat­ing system can not boot. The options are: Disabled, Enabled.

Resources Controlled By

If set at Auto, the BIOS arranges all system resources. If there exists con­flict, select Manual. The options are: Auto (ESCD), Manual.
If the manual options, after the featrue IRQ Resources being pressed, of
IRQ- Assigned To are: PCI Device, Reserved. When resources were con­trolled manually, assign each system interrupt a type, depending on each
device type to use the interrupt.

3 - 17

865 D y n asty M ainboard Manual

PCI/VGA Palette Snoop

Set this feature to be enabled if any ISA adapter card installed in the
system requires the VGA palette snoop function.
The options are: Disabled, Enabled.

INT Pin 1/2/3/4/5/6/7/8 Assignment

This feature allows you to assign the PCI IRQ numbers for PCI slots.
Selecting the default, Auto, allows the PCI controller to automatically allo­cate the IRQ numbers. The options are: Auto, 3, 4, 5, 7, 9, 10, 11, 12, 14, 15.

PC Health Status

Shutdown Temperature

This feature helps to shutdown the system when the system temperature
is as high as the selected temperature to prevent from the overheat prob­lem. The option list presents all the temperatures that supported by the
board and Disabled.

VCORE / VID / 3.3V / +5V / 12V / 3VSB / -12V / 5VSB / V oltage Battery
/ CPU Te mperature / SYSTEM Temperature / CPU FA N / SYSTEM FA N
/CHIP FA N

These items allow end users and technicians to monitor data provided by
the BIOS on this mainboard. It is not user-configurable.

3 - 18

BIOS Setup

Load Fail-Safe Defaults

This submenu is selected to diagnose the problem after the computer boots, if
the computer will not boot. These settings do not give optimal performance.

Load Optimized Defaults

This submenu is selected for default settings which provide the best system
performance.

Supervisor/User Password

To enable the Supervisor/User passwords, select the item from the Standard
CMOS Setup. You will be prompted to create your own password. Type your
password up to eight characters and press Enter. You will be asked to confirm
the password. Type the password again and press Enter. To disable password,
press Enter twice when you are prompted to enter a password. A message
appears, confirming the password is disabled.

Under the BIOS Feature Setup, if Setup is selected under the Security Option
field and the Supervisor/User Password is enabled, you will be prompted
password every time you try to enter the CMOS Setup Utility. If System is
selected and the Supervisor/User Password is enabled, you will be requested
to enter the Password every time when you reboot the system or enter the
CMOS Setup utility.

Save and Exit Setup

After you have made changes under Setup, press Esc to return to the main
menu. Move cursor to Save and Exit Setup or press F10 and then press Y to
change the CMOS Setup. If you did not change anything, press Esc again or
move cursor to Exit Without Saving and press Y to retain the Setup settings.
The following message will appear at the center of the screen to allow you to
save data to CMOS and exit the setup utility: SAVE to CMOS and EXIT (Y/N)?

Exit without Saving

If you select this feature, the following message will appear at the center of the
screen to allow you to exit the setup utility without saving CMOS modifica­tions: Quit Without Saving (Y/N)?

3 - 19

865 D y n asty M ainboard Manual

This Page Left Blank for Note

3 - 20