FIC K8M-800T/M User Manual

K8M-800T/M

MAI NBOARD

MANUAL

DOC No.: M03601
Rev. : A0
Date : 9, 2003
Part No. : 25-11110-00

Handling Precautions

Warning:

1. Static electricity may cause damage to the integrated circuits on

the motherboard. Before handling any motherboard outside of its
protective packaging, ensure that your body carries no static

electric|charge.

2. There is a danger of explosion if the battery is incorrectly
replaced. Replace only with th e same type of battery, or an

equivalent type|recommended by the manufacturer.

3. Discard used batteries according to the manufacturer’s
instructions.

4. Never run the processor without the heatsink properly and firmly

attached. PERMANENT DAMAGE WILL RESULT!

Observe the following basic precautions when handling the motherboard
or other com puter components:

n Wear a static wrist strap which is|connected to a natural earth

ground.

n Touch a grounded or anti-static surface or a metal fixture such as a

water pipe.

n Avoid contacting the components on add-on cards, motherboards,

and modules with the golden finger connectors plugged into the
expansion slot. It is best to handle system components by their
m ounting brackets.

The above methods prevent static build-up and causes it to be discharged
properly.

Trademark

All tra demarks mentioned in this manual are registered properly by
the respective owners.

Handling Precautions

This manual may not, in whole or in part, be photocopied, reproduced,
transcribed, translated, or transmitted in whatever form without the
written consent of the manufacturer, except for copies retained by the
purchaser for personal archival purposes.

Notice

i

Table of Contents

T able of Contents

Chapter 1 Overview

Package Checklist .................................................................................. 1-2

The K8M-800T/M Mainboard ........................................................ 1-3

Main Features ........................................................................................ 1-4

FIC Unique Innovation for Users (NOVUS) -

Enhanced Mainboard Features and System Support....................... 1-5

Chapter 2 Ins tallation Procedures

1). Set System Jumpers ......................................................................... 2-2

Clear CMOS .............................................................................. 2-2

LED Type Select ....................................................................... 2-2

2). Install Memory Modules ................................................................. 2-3

3). Install the CPU.................................................................................. 2-4

Connect ATX Power................................................................ 2-5

4). Install Expansion Cards ................................................................... 2-6

5). Connect Devices............................................................................... 2-8

Floppy Diskette Drive Connector.......................................... 2-8

IDE Device Connectors........................................................... 2-8

Fan Connectors ........................................................................ 2-9

Power Connectors ................................................................... 2-9

Front Panel Block Connector ................................................. 2-10

IR and Speaker Connector...................................................... 2-11

Chassis Intrusion Connector ................................................. 2-11

Serial IRQ Connector............................................................... 2-12

Wake-On-LAN Connector...................................................... 2-12

Serial ATA Connectors ............................................................ 2-12

SPDIF Connectors ................................................................... 2-13

1394 Connectors (optional) .................................................... 2-13

CD Audio-In Connectors ........................................................ 2-14

Types of Rear Panel I/O Connectors ..................................... 2-14

RJ45 LAN Connector .............................................................. 2-14

PS/2 Keyboard and Mouse Connector................................. 2-15

Printer Connector..................................................................... 2-15

Serial Port Connectors (K8M-800T)...................................... 2-15

Serial Port Connectors (K8M-800M) .................................... 2-16

ii

K8M-800T/M Mainboard Manual

Chapter 3 BIOS Setup

CMOS Setup Utility ............................................................................... 3-1

Standard CMOS Setup .......................................................................... 3-2

Advanced BIOS Features ..................................................................... 3-4

Advanced Chipset Features ................................................................. 3-7

Integrated Peripherals ........................................................................... 3-10

Power Management Setup.................................................................... 3-14

PnP/PCI Configurations........................................................................ 3-17

PC Health Status .................................................................................... 3-19

Frequency/Voltage Control .................................................................. 3-19

Load Optimized Defaults ....................................................................... 3-20

Supervisor/User Password ................................................................... 3-20

Save and Exit Setup ............................................................................... 3-20

Exit without Saving................................................................................ 3-20

CRT Connector (K8M-800M)................................................. 2-16

Audio I/O Jacks ....................................................................... 2-17

Front Audio Connector........................................................... 2-17

Printer Connector..................................................................... 2-18

Universal Serial Bus Connectors ........................................... 2-18

1 - 1

Overview

Overview

Chapter 1

This new Mainboard is a microATX sized board supporting the latest genera­tion of AMD 64 processors at FSB 800MHz. Memory is up to DDR400 MHz
and has 2 DDR SDRAM DIMMs for up to 2 GBs. This board provides users
with an ATA133 data transaction for peripheral IDE drives .

This board is based upon the high performance VIA K8T800 (K8M-800T)/
K8M800 (K8M-800M )/as its North Bridge and t he VIA VT8237 as its
South Bridge. Its AGP functions supported AGP 3.0 interface and the most
robust 3D games with software environments.

The board features onbo ard audio and LAN function; also, the serial ATA
feature replaces the standard parallel ATA physical storage interface and al­lows future enhanceme nts to the computing platform. It is completely soft­ware com patible with parallel ATA, requiring no modification to your operat­ing system. For more details, please read the help file in the lst Utilities CD.

This mainboard comes with a versatile range of I/O features such as serial port
(s) and/or 1 CRT port, (K8M-800T: 2 COM ports, no CRT port; K8M-800M: 1
COM port + 1 CRT port), 1 parallel port, 1 LAN, 2 optional IEEE 1394, 1 PS/2
m ouse and keyboard c onnector, 8 USB ports, and 1 media conn ector (front
audio, Line-in, Line-out and Mic-in). In addition, the board is equipped with 2
dual channel enhanced PCI bus master IDE connectors. Ample expansion is
available through 3 PCI and 1AGP allow for enjoyment of the CPU’s benefits
wth internet applicatons, video/3D graphics performance, and so forth.

Oth er key features are Remo te On/Off, A uto Power Failure Recovery, inte­grated tem perature monitoring and system fan control. Also, included are a lst
Utilities CD with enhanced drivers and a few bundled soft-ware solutions.

1 - 2

K8M-800T/M Mainboard Manual

Package Checklist

If you discover any item belo w was damaged or lost, please contact your
vendor.

NOTE: A 1st Utilities CD that contains patch files, onboard video/
audio chip drivers, related online help and other useful information
can be found in your mainboard package.

Please install the 1st Utilities immediately after your Windows oper­ating system installation is complete. To install, place your 1st Util­ity in th e drive. An operating menu will appears on your monitor.
Please sel ect Auto Installation. The CD will automa tically detect
which softwa re tools (patch files, d rivers) the mainboard needs.
Press OK button to go through the whole installation procedure in
a very straight forward and easy way. The CD also provides you with
a way to select which patch files and software drivers the onboard
chips use. The m ain menu of 1st Utilities lists all the functions

that are allowed by this board.

1 - 3

Overview

The K8M-800T/M Mainboard

1 - 4

K8M-800T/M Mainboard Manual

M ain Features

n CPU

Athlon 64 processors from 3200+ and up* at FSB 800 MHz
(*: not tested when this manual was printed)

n Chipset

North Bridge: VIA® K8T800 (K8M-800T)

/K8M800(K8M-800M)

South Bridge: VIA® 8237

n Memory

2 memory sockets :
supp ort 184-pin DDR266/333/400 (PC2100/ PC2700/PC3200*) DDR
SD RAM memory size up to 2 GBs total

n Exp ansion Slots

1 AGP 8X Slot
3 PCI Slots

n Aud io Features

Realtek ALC655/658 (dual layout) controller; AC97
LINE_IN, LINE_OUT, MICROPHONE_IN Jack

5.1 audio channel
Front audio pinheaders

n I /O Ports

2 IDE connectors ­PIO, Bus Master, Ultra DMA 66/100/133 up to 4 devices
COM1 and COM2
1 parallel port
PS/2 mouse and PS/2 keyboard
8 USB ports

1 - 5

Overview

n M ounting Holes

9 holes

n M ainboard Size

9.6 x 9.6 (unit: inch)

n I EEE 1394 Ports (optional)

V T6307L
2 ports
1 bracket with cable

n SA TA Connections

V T8237
RAID 0, 1, 0+1
2 optional cables

n LAN

RTL8100C 10/100M Fast Ethernet/
8110S Gigabit Ethernet (dual layout)

FIC Unique Innovation for Users (NOVUS) -

Enha nced Mainboard Features and System Support

n BIOS Guardian

BIOS Guardian effectively acts as a fire-wall against viruses that can attack
the BIOS while the system is running and when default is enabled. Please
read Page 3-7 for more detailed information. NOTE: BIOS Guardian must

b e disabled before you reflash BIOS.

1 - 6

K8M-800T/M Mainboard Manual

n Easy Key

Instead of completing the multi-layered BIOS setup process, these 3 Easy
Key functions provide direct access to the Sub-Menu when completing
BIOS settings adjustments.

Easy-Keys are as follows:

Ctrl + c: To enter clock settings menu.
Ctrl + p : To load Performance Default settings and restart.
Ctrl + f: To load Fail-Safe Default settings and restart.

2 - 1

Installation Procedures

Chapter 2

Installation Procedures

The mainboard has several user-adjustable jumpers on t he board that allow you to
configure your system to suit your requirements. This chapter contains information
on the various jumper settings on your mainboard.

To set up your computer, you must complete the following steps:

Step 1 - Set system jumpers
Step 2 - Install memory modules
Step 3 - Install the Central Processing Unit (CPU)
Step 4 - Install expansion cards
Step 5 - Connect ribbon cables, cabinet wires, and power supply
Step 6 - Set up BIOS software
Step 7 - Install supporting software tools

WARNING: Excessive torque may damage the mainboard. When
using an electric screwdriver on the mainboard, make sure that
the torque is set to the allowable range of 5.0 ~ 8.0kg/cm.

Mainboard components contain very delicate Integrated Circuit
(IC) chips. T o prevent static electricity from harming any of the
sensitive components, you should follow the following precau­tions whenever working on the computer:

1. Unplug the computer when working on the inside.

2. Hold components by the edges and try not to touch the IC

||||chips, leads, or circuitry.

3. W ear an anti-static wrist strap which fits around the wrist.

4. Place components on a grounded anti-static pad or on the bag
that came with the component whenever the components are
separated from the system.

2 - 2

K8M-800T/M Mainboard Manual

Clear CM OS

The CMOS RAM is powered by the onboard button cell battery.
To clear the RTC data:

(1) Turn off your com puter;
(2) Open the system case and disconnect the ATX power cable;
(3) Place the jumper cap onto the pinpair 2-3 for at least 6 seconds

to enable CMOS clearance;

(4) Place the jumper cap onto the pinpair 1-2 to disable the effect of

CMOS clearance;
(5) Connect the ATX power cable and close the system case;
(6) Turn on your com puter until CMOS checksum error appears;
(7) Hold down the Delete key when booting;
(8) Enter the BIOS Setup to re-enter user preferences.

1.) Set System Jumpers

LED Type Select

This 2x3 jumper allow you to select Power LED Type, single LED or dual
LED.

2 - 3

Installation Procedures

2.) Install Memory Modules

1. Locate DDR DIMM sockets
on the m ainboard.

2. Install DDR DIMM straight down

into socket 1, using both hands,
then socket 2, and so forth.

NOTE: Please refer to Front Panel Block Connector Section of this
chapter for detail information.

2 - 4

K8M-800T/M Mainboard Manual

3.) Install the CPU

The proc edure below shows you
how to install your CPU, its fan
and heatsink. Before you begin,
loc ate th e CPU socket on th e
m ainboard.

1. Swing the lever upward to 90 degrees.

Press the clips outward with both hands to remove the DIMM.

3. The clip on both ends of the
socket will close to hold the DDR
DIMM in place when the DDR
DIMM reaches the bottom of the
socket.

The main board has a built-in Switching
Voltage Regulator to support CPU Vcore
autodetection. That is, It has the ability to
detect and recognize the CPU health con­dition from the BIOS Setup Screen.

Apply some thermal material, such as paste or
tape, on the CPU top, and install a fan with a
heatsink that is approved by the manufa cturer
to avoid CPU damage. For detail info rmation,
please refer to the CPU manufacturer website.

Affix th e CPU by press ing the lever downward
and locking it beside the socket.

2 - 5

Installation Procedures

Connect ATX Power

The 20-hole power plug (top right) is connected
to the ATX power 20-pin pinheaders. The 4-hole
12V power plug (bottom right) is inserted in the
ATX_12V powe r connector.

The plug from the power supply can only be in-
serted in one orientation because of the differ­ent hole s izes. Find the proper orientation and
push down firm ly making sure that the pins are
aligned.

3. Place the fan with h eatsink on the CPU top
and pres s down on the two plastic clips,

hooking them up wit h the holes on the two

sides of the retention module.

4. Press t he white bar on each clip down to
fasten t he fan set on the retention module.

2 - 6

K8M-800T/M Mainboard Manual

CAUTION:

1. Make sure to unplug the power supply when adding or remov

ing expansion cards or other system components. Failure to
do so may cause severe damage to both the mainboard and
expansion cards.

2. Always observe static electricity precautions.

3. Please read Handling Precautions at the start of this manual.

4). Install Expansion Cards

Th is s ection describes how to connect an expansion card to o ne of your
system expansion slots. Expansion cards are printed circuit boards that, when
con nected to the mainboard, increase th e capabilities o f your sys tem. For
example, expansion cards can provide video and sound capabilities. The
m ainboard features one AGP and three PCI bus expansion slots.

NOTE:

The CPU installing procedures should be:

1. Insert the CPU (with its fansink and retention module) on the
socket.

2. Connect the 4-pin plug of the power supply

3. Connect the 20-pin plug of the power supply.
T o remove the processor, please do it in reverse order.

2 - 7

Installation Procedures

1. Select an available expansion slot.

2. Remove the corresponding slot cover from the computer chassis. Un-

screw the m ounting screw that secures the slot cover and pull the slot cover
out from the computer chassis. Keep the slot cover mounting screw nearby.

3. Push the card firmly into the s lot.
Push down on one end of the e xpan­sion card, then the other. Use this r ock­ing motion u ntil ca rd is firmly seated
inside the expansion slot. Secure the
card with the screw removed in Step 2.

2 - 8

K8M-800T/M Mainboard Manual

IDE Device Connectors

The two connectors, PRIMARY
and SECONDARY, are u sed for
your IDE hard disk drives, CD drives,
LS-120|drives, or IDE ZIP drives.

5). Connect Devices

Floppy Diskette Drive Connector

This connector provides the connection with your floppy disk drive.

Insert the floppy ribbon cable (below)
onto th e floppy connector.

The colored stripe (indicated by the
arrow , right) of the ribbon cable must
be on the sam e side as Pin 1.

Insert the floppy ribbon cable (below)
onto th e floppy connector.

The colored stripe (indicated by the
arrow , right) of the ribbon cable must
be on the sam e side as Pin 1.

2 - 9

Installation Procedures

Power Connectors

The 20-pin male block connector is connected to the ATX power supply. The
4-pin male block connector is for the ATX_12V power supply. Both con nec-
tors are linked with your ATX power supply. The plug from the power supply

can only be inserted in one orientation because of the different hole sizes. Find

the proper orientation and push down firmly making s ure th at the pins are
aligned.

Fan Connectors

The two connectors, CPU_F AN and SYS_FAN are linked to the CPU fan and
case fan, respectively. PWR_FAN can be used with the power supply cooling
fan.

2 - 10

K8M-800T/M Mainboard Manual

Front Panel Block Connector

(1) Reset Sw itch is connected to the reset button. Push this switch to reboot

the system instead of turning the power button off and on.

(2) H DD LED is connected to the IDE device indicator. This LED will blink

when the hard disk drives are activated.

(3) Power (Single and Dual) /Sleep LED

Please refer to the tables below for the representations of LED states.
There is also 3-Pin Power LED connector on board for those cases that
have a 3-pin plug.

This block connector includes the
co nnectors for linking with the
Power LED (3-pin), HDD LED,
power but ton, power/s leep/mes­sage waiting button, and the reset
bu tton on the front panel of the
system case. Please identify the
polarities of the plug wires for the
case speaker and LEDs. Please ask
v endor about this informat ion
when you buy them and install the
system by yourself. The plug wire
polarities of these buttons will not
affect the function.

2 - 11

Installation Procedures

(1) IR is a pinheader that is used for linking with your ID device to

allow transmission of data to another system that also supports the
IR feature.

(2) SPK is connected with the case

speaker.

(4) Power Button is connected with the power button. Pushing this switch

allows the system to be turned on and off rather than using the power
supply button.

Chassis Intrusion Connector

This conn ector allows you to enable (or
disable) system activation if and when the
system out casing is being rem oved. A high
level signal to the connector will indicate
to the system that the chassis has b een
opened. Pin 1 is Signal, Pin 2 is G ND.

NOTE: To use IR functions you must adjust the BIOS features intro­duced in the section titled Integrated Peripherals, Chapter 3.

IR and Speaker Connector

2 - 12

K8M-800T/M Mainboard Manual

Serial ATA Connectors

The 2 SATA connectors provide you with connections to serial ATA devices
that conform to the Serial ATA specification. Serial ATA supports all ATA and
ATAPI devices. The pictures below le ft show the two SATA cables (the top
one is for power; the bottom one is for data).

NOTE: Please read the Integrated Peripherals section of Chapter 3
for more details.

W ake-On-LAN Connector

This connector is used for connection with
a network card with wake-on LAN feature.
It will p ower up the system if a signal is
received through the network card. Pin 1 is
+5VSB, Pin2 is GND, Pin 3 is signal.

Serial IRQ Connector

This 2-pin connecto r is used for some
system integration use.
Pin 1 is signal, Pin 2 is G ND.

2 - 13

Installation Procedures

1394 Connectors (optional)

The 2 optional 1394 pinheaders on th e board provide you with two connec­tions for peripherals which have 1394 connectors through an optional bracket
with cable (see the figure below). The pin definitions of the 1394 pinheaders
are listed below. The 1394_26 p ort may be in tegrated on rear panel for some
system cases.

SPDIF Connector

The SPDIF_OUT conn ector is used for audio output with SPDIF spec. Pin
definitions: Pin1 is 5V, Pin2 is SPDIF signal, Pin3 is GND.

2 - 14

K8M-800T/M Mainboard Manual

RJ45 LAN Connector

The RJ45 jack of the LAN port is used for the LAN cable plug.

Types of Rear Panel I/O Connectors

The rear panel I/O connectors of the K8M-800T and K8M-800M are different.
One 1394 socket is optional upon customer request. A 1394 socket may be on
the top of USBs for special systems.

CD Audio-In Connectors

The connectors, CD_IN and AUX_IN, are
for CD- ROM drive audio analog input use.
Pin definitions: Pin1is Left, Pin2 and P3 is
G ND, Pin4 is GND.

2 - 15

Installation Procedures

PS/2 Keyboard and Mouse Connector

These two 6-pin female connectors (keyboard is purple and mouse is green)
are used for your PS/2 keyboard and PS/2 mouse.

Serial Port Connectors (K8M -800T)

COM1/2 (teal colored 9-pin D-sub male connectors) allow you to connect with
your devices that use serial ports, such as a serial mouse or an external modem.

2 - 16

K8M-800T/M Mainboard Manual

This connector is linked to your m onitor. The pinheaders pin assignments are
shown at right side.

CRT Connector (K8M-800M)

Serial Port Connectors (K8M -800M)

COM1 (teal colored 9-pin D-sub male connector) and COM2 (9-pin male
connector) allow you to connect with devices that use serial ports, such as a
serial mouse or an external modem.

2 - 17

Installation Procedures

Audio I/O Jacks

LINE_OUT (lime) c an be connected to headphones or p referably powered
speakers. LINE_IN (light blue) allows tape players or other audio sources to
be recorde d by your computer or played through the LINE_OUT. MIC_IN
(pink) allows microphones to be connected for audio input.

NOTE: If you do not use F_AUDIO , please keep the pinpair 5-6, 9-10
short as default; also, when the front headphone is plugged in,
the rear audio output will be disabled.

The m ainboard has a front panel audio, F_AUDIO, connector (Intel spec.). It
allows you to attach an audio device via the front panel (instead of rear panel)
by a ribbon cable. Its pin definitions are presented below.

Front Audio Connector

2 - 18

K8M-800T/M Mainboard Manual

Universal Serial Bus Connectors

The figure at below shows the pin
assignments of the USB4/5. Those of
USB6/7 are similar.

The m ainboard has eight USB ports; four USB black jacks that are integrated
on the edge of the board, and four other USB ports (pinheaders) on the board.
They allow users to attach to USB devices either from the rear or front panels.
Please note that your operating system must support USB 1.1/2.0 features.

Printer Connector

This 25-pin D-Sub female connector (burgundy­colored) is attached to your printer.

3 - 1

BIOS Setup

Chapter 3

BIOS Setup

This mainboard c omes with a chip fro m Award BIOS that contains the ROM
Setup information for your system. (This chip serves as an interface between
the p rocessor and the rest of the mainboard components.) This section ex­plains the information cont ained in the Setup program and tells you how to
m odify the settings according to your system configuration.

CM OS Setup Utility

The Setup utility program allows updates to the mainboard configuration set­tings. The BIOS setup values will be saved in the CMOS. It is executed when
you change the system configuration, you change the system backup battery,
or the system detects a configuration error and asks you to run the Setup
prog ram. Use the arrow keys to select, and press Enter to run th e selected
program .

3 - 2

K8M-800T/M Mainboard Manual

Standard CMOS Setup

The Standard CMOS Setup screen is displayed above. Each feature may have
one or m ore option settings. Use the arrow keys to highlight the feature you
want to change and then use PgUp or PgDn to select the value you want for
that feature.

NOTE: The system BIOS automatically detects memory size, thus no changes
are necessary.

Date

To set the date, highlight the Date field and then press PgUp/PgDn or +/-
keys to set the current date. Follow the month, day and year format.

Time

To set the time, highlight the Time field and then press PgUp/PgDn or +/-
keys to set the current time. Follow the hour, minute, and second format.

3 - 3

BIOS Setup

Hard Disks

This field records the specifications for all non-SCSI hard drives installed
in the system. The onboard PCI IDE connectors provide Primary and Sec­onda ry channels for connecting up to four IDE hard disks or other IDE
devices. Each channel can support up to two hard disks, the first of which
is the Master and the second is the Slave.

Hard Dis k Configurations

Capacity: The hard disk size. The unit is Bytes.
Cylinder: The cylinder number of the hard disk.
H ead: The read/write head number of the hard disk.
Precomp: The cylinder number at which the disk drive

changes the write current.

Landing
Zone: The cylinder number on which the disk drive heads

(read/write) are seated when the disk drive is
parked.

Sector: The sector num ber of each track defined on the

hard disk.

Drive A / Drive B

This field re cords the types of floppy drives installed in th e system. To
ent er the configuration value for a particular drive, highlig ht its corre-

sponding field and then select the drive type using the

lef t- or right -arrow

key.

Floppy 3 Mode Support

This is a Japanese standard floppy type drive.

Video

Set this field to the type of video display card installed in the system.

Halt On

This field determines which types of errors will cause the system to halt.

3 - 4

K8M-800T/M Mainboard Manual

Advanced BIOS Features

Hard Disk Boot Priority

This fe ature will auto d etect all hard disks of bootable devices on the
system . It also allows you to select hard disk device booting priority.

CPU Internal Cache

This controls the status of the processor’s internal cache area.
The options are: Enabled, Disabled.

External Ca che

This controls the status of the external (L2) cache area.
The options are: Enabled, Disabled.

CPU L2 Ca che ECC Checking

Set the ECC (Error-Correcting Code) feature for Level 2 cache. Facilitates
error detection/correction when data passes through Level 2 cache.
The options are: Enabled, Disabled.

Quick Power On Self Test

When enabled, allows the BIOS to bypass the extensive memory test.
The options are: Enabled, Disabled.

3 - 5

BIOS Setup

First/Second/Third Boot Device

This feature allows you to select the boot device priority.
The o ptions are: Floppy, LS120, Hard Disk, CDROM, ZIP100, USB-FDD,
USB-ZIP, USB-CDROM, LAN, Disabled.

Boot Other Device

This feature allows you to select the boot device priority.
The options are: Enabled, Disabled.

Swa p Floppy Drive

Allows you to switch the order in which the operating system accesses
the floppy drives during boot up. The options are: Enabled, Disabled.

Boot Up Floppy Seek

When enabled, assigns the BIOS to perform floppy diskette drive tests by
issuing the time-consuming seek commands.
The options are: Enabled, Disabled.

Boot Up Numlock Status

When set to On, allows the BIOS to automatically enable the Num Lock
Function when the system boots up. The options are: On, Off.

Typematic Rate Setting

The term t ypematic means that when a keyboard key is held down, the
character is repeatedly entered until the key is released.
The options are: Disabled, Enabled.

Typematic Rate (Chars/Sec)

This feature is available only if the above item, Typematic Rate Setting, is
set at Enable d. Sets the rate of a character repeat when the key is held
down. The options are: 6, 8, 10, 12, 15, 20, 24, 30.

Typematic Delay (Msec)

This feature is available only if the item, Typematic Rate Setting, is set at
Enabled. Sets the delay time before a character is repeated.
The options are: 250, 500, 750, 1000 millisecond.

3 - 6

K8M-800T/M Mainboard Manual

Security Option

Allows you to s et the security level of the system.The options: Setup,
System .

APIC Mode

Allows you to decide if the system enters the APIC (Advanced Program­m able Interrupt Controller) mode or not for more IRQs can be released.
The options are: Enabled, Disabled.

MPS Version Control For OS

With two CPUs are onboard (not a feature of this board) this feature allows
you to select Mult i-Processor Spec. (MPS) version control for OS when
the logo test executes. The options are: 1.1, 1.4.

OS Select For DRAM > 64MB

If your o perating system (OS) is OS/2, select the option OS2. Otherwise,
stay with the default setting Non-OS2.The options are: Non-OS2, OS2.

HDD S.M.A.R.T. Capability

S.M.A.R.T. stands for Self-Monitoring and Analysis Reporting Technol­ogy which allows yo ur hard disk drive to report any read/write errors and
issues a warning with LDCM installed. The options: Disabled, Enabled.

Video BIOS Shadow

Enabling this feature will copy the video BIOS to shadow RAM, it will
improve the system performance. The options are: Enabled, Disabled.

Full Screen LOGO Show

This decides whether or not the full screen logo is s hown during system
boot ups. The options are: Enabled, Disabled.

BIOS Guardian

It allows the system to prevent compu ter viruses. Users will need to dis­able it to update BIOS. The options are: Enabled, Disabled.

NOTE: Please disable the BIOS Guardian feature before you start
to reflash BIOS.

3 - 7

BIOS Setup

Advanced Chipset Features

DRAM Configuration

Current FSB Frequency, Current DRAM Frequency

This item allows you to get current FSB and DRAM frequencies.

BIOS Guardian and Reflash BIOS

BIOS Guardian by default is enabled, thus effectively acting as a fire­wall against viruses that can attack the BIOS while the system is
running. It must be disabled before you reflash BIOS.

The steps below show you how t o the BIOS G uardian off and on
when you want to reflash BIOS:

1. Press Del key while booting and go to CMOS Setup Utility menu.

2. Go to the Advanced BIOS Features submenu.

3. Set the feature BIOS Guardian at Disabled.

4. Save the setting and exit. The system will restart.

5. The POST screen holds. A message about BIOS G uardian shows.

6. Press the Space bar.

7. Reflash the BIOS. Restart the system after you are finished.

8. The POST screen holds. A message about BIOS G uardian shows.

9. Press G key. The feature BIOS Guardian will be enabled again.

3 - 8

K8M-800T/M Mainboard Manual

DDR Timing Setting by

This feature allows you to decide DRAM clock timing.
The options are: Auto, Manual.

Max Memlock (Mhz)

This fea ture allo ws you to place an artificial memory clock limit on the
system . Memory is presented from running faster than this frequency.
The options are: 100, 133, 166, 200.

AGP & P2P Bridge Control

AGP Aperture Size

This feature defines the size of the ape rture if you use an AGP graphics
adapter. It refers to a s ection of the PCI memo ry address range used for
graphics memory. The options are: 32M, 64M, 128M, 256M.

AGP Mode

Chipset AGP Mode support. The options are: 1X, 2X, 4X.

AGP Driving Control / AGP Driving Value

These two features allow you to manually improve the perform ance of AGP
card m anually by pressing the Page Down/Page Up key if necessary.
The options of AGP Driving Control are: Auto, Manual.

AGP Fa st Write

This feature allows you to set AGP fast write mode.
The options are: Disabled, Enabled.

AGP Ma ster 1 WS Write

When enabled, the AGP bus master write acc ess to D RAMs will add one
wait-state cycle. The options are: Enabled, Disabled.

AGP Ma ster 1 WS Read

When enabled, the AG P bus master read access to the D RAMs will add one
wait-state cycle. The options are: Disabled, Enabled.

3 - 9

BIOS Setup

LDT & PCI Bus Control

Upstrea m LDT Bus Width

This feature allows you to select the range of upstreaming LDT (Lightning
Data Transport) bus width. The options are: 8 bit, 16 bit.

Downstrea m LDT Bus Width

Th is feature allo ws you to select the rang e of downstreaming LDT
(Lightning Data Transport) bus width. The options are: 8 bit, 16 bit.

LDT Bus Frequency

This feature allows you to set the LDT bus frequency.
The options are: Auto, 800 MHz, 600 MHz, 400 MHz, 200 MHz.

PCI1/2 Master WS Write

When Enabled, Writes to the PCI bus are commanded with wait states.
The options are: Enabled, Disabled.

PCI1/2 Post Write

Enables CPU to PCI bus POST write. The options are: Enabled, Disabled.

PCI Delay Transaction

The chipset has an embedded 32-bit p osted write buffer to support delay
transactions cycles. The options are: Enabled, Disabled.

Memory Hole

When you install a Legacy ISA card, this feature allows you to select the
m emory hole address range of the ISA cycle when the processor accesses
the selected address area. Please read your card manual for detail informa­tion. When disable d, the memory hole at the (15-16MB) address will be
treated as a DRAM cycle when the processor accesses the15~16MB ad­dress area. The options are: Disabled, 15M - 16M.

VLink Data Rate

This item allows users to select the supported VLink data rate.
The options are: 8X, 4X.

3 - 10

K8M-800T/M Mainboard Manual

Integrated Peripherals

Init Display First

When you install an AG P VGA card and a PCI VGA card on the board, this
feature allows you to select the first initiation of the monitor display from
which card. The options are: PCI Slot, AGP.

System BIOS Cacheable

When enabled, allows the ROM area F000H-FFFFH to be cacheable when
cache controller is activated. The options are: Enabled, Disabled.

VGA Share Memory Size (K8M-800M only)

It allows user to select the frame buffer size of VG A share memory.
The options are: Disabled, 8M, 16M, 32M, .

VI A OnChip IDE Device

OnChip SATA

This feature allows you to disable the optional onboard SATA chip.
The options are: Enabled, Disabled.

SATA Mode

This item allows you to select the serial ATA mode
The options are: IDE, RAID.

3 - 11

BIOS Setup

IDE DMA transfer access

This item allo ws you to disable the IDE DMA (Direct Memory Access)
transfer access function. The options are: Enabled, Disabled.

OnChip IDE Channel0/1

When enabled, this allows you to use the onboard primary/secondary PCI
IDE. The options are: Enabled, Disabled.

IDE Prefetch Mode

When set at Enabled, this allows data to be posted to and prefetched from
the primary IDE dat a ports. Data prefetching is initiated when a data port
read occurs. The read prefetch eliments latency to the IDE data ports and
allows them to be performed back to back for the highest possible PIO data
transfer rates. The first data port read of a sector is called the demand read.
Subsequent data port reads from the sector are called prefetch reads. The
dem and read and all prefetch reads must be of the same size (16 or 32 bits).
The options are: Enabled, Disabled.

Primary Ma ster/Slave PIO

This allows an autom atic or a manual configuration of the PCI primary IDE
hard drive (master/slave) mode. The options are: Auto, Mode 0, ..., 4.

Secondary Ma ster/Slave PIO

This allows an automatic or a manual configuration of the PCI secondray
IDE hard drive (master/slave) mode. The options are: Auto, Mode 0, ..., 4.

Primary Ma ster/Slave UDMA

This allows an automatic configuration of the PCI primary IDE hard drive
(m aster/slave) mode if Ultra DMA is supported both on the motherboard
and the hard disk. The options are: Auto, Disabled.

Secondary Master/Slave UDMA

This allows an automatic co nfiguration of the PCI secondary IDE hard
drive (master/slave) mode if Ultra DMA is su pported both on th e
m otherboard and the hard disk. The options are: Auto, Disabled.

3 - 12

K8M-800T/M Mainboard Manual

IDE HDD Block Mode

Block mode is also c alled block tran sfer, mu ltiple c ommands, or mult iple
sector read/write. If your IDE hard drive supports block mode (most new
drives do), select Enabled for automatic detection of the optimal number of
block read/writes the drive can support per sector .
The options are: Enabled, Disabled.

VIA OnChip PCI Device

VIA-3058 AC97 Audio

This allows you to disable AC97 audio function in South Bridge.
The options are: Auto, Disabled.

OnChip USB Controller

Enables the onboard USB controller.
The options are: Enabled, Disabled.

OnChip USB 2.0 Controller

Disable this option if you are not using the onboar d USB 2.0 feature (USB

1.1 not effected). The options are: Disabled, Enabled.

USB Lega cy Support

Your sys tem contains a Universal Serial Bus (USB) controller and you
have a USB keyboard Device. When se t at Auto, the BIOS will automati­cally detect if USB keyboard is installed automatically.
The options are: Auto, Enabled, Disabled.

SuperIO Device

Onboard FDC Controller

When enabled, the floppy diskette drive (FDD) controller is activated.
The options are: Enabled, Disabled.

Onboard Serial Port 1/2

If the serial port 1/2 uses the onboard I/O controller, you can modify your
serial port parameters.
The options are: 3F8/IRQ4, 3E8/IRQ4, 2F8/IRQ3, 2E8/IRQ3, Disabled.

3 - 13

BIOS Setup

UART Mode Select

This allows you to select the IR modes if the serial port 2 is used as an IR
port. Set at Normal, if you use COM2 as the serial port, instead of as an IR
port. The options are: Normal, IrDA, ASKIR, SCR.

UR2 Duplex Mode

This allows you to select the IR modes. The options are: Full, Half.

Onboard Parallel Port

Allows you to select from a given set of parameters if the parallel port uses
the onboard I/O controller.
The options are: Disabled, 378/IRQ7, 278/IRQ5, 3BC/IRQ7.

Parallel Port Mode

Allows you to connect with an advanced printer via the port mode it sup­ports. The options are: SPP, ECP, EPP, EPP+ECP.

ECP Mode Use DMA

This feature allows you to select Direct Memory Access (DMA) channel.
The options are: 1, 3.

Onboard La n Device

This allows you to disable onboard LAN feature.
The options are: Enabled, Disabled.

Onboard La n Boot ROM

Enables and disables the onboard LAN Boot ROM.
The options are: Enabled, Disabled.

Onboard 1394 Device

This allows you to disable the onboard 1394 feature.
The options are: Enabled, Disabled.

3 - 14

K8M-800T/M Mainboard Manual

ACPI function

This feature allows you to disable the ACPI function.
The options are: Enabled, Disabled.

ACPI Suspend Type

This feature allows you to s elect suspen d mode when the system is in
ACPI mode. The options are: S1 (POS), S3 (PTR), S1&S3.

Power Ma nagement Option

This feature allows you to adjust the power management features.
Select User Define for configuring your own power management features.

Min Sa ving init iates all predefined timers in their minimum values. Max
Saving, on the other hand, initiates maximum values.

The options are: User Define, Min Saving, Max Saving.

HDD Power Down

This feature allows the BIOS to turn the HDD motor off when the system is
in Suspend mode. Selecting 1 Min..15 Min allows you to define the HDD
idle time before the HDD enters th e Power Saving Mode. The options 1
Min..15 Min will not work concurrently. When HDD is in the Power Saving
Mode, any access to the HDD will wake the HDD up.
The options are: Disable, 1 Min..15 Min.

Power M anagement Setup

3 - 15

BIOS Setup

MODEM Use IRQ

This feature allows you to select the IRQ# to meet your modem IRQ#.
The options are: NA, 3, 4, 5, 7, 9, 10, 11.

Soft-Off by PWRBTN

The selection Delay 4 Sec. will allow the system shut down after 4 seconds
after the power button is pressed. The selection Instant-Off will allow the
system shut down immediately once the power button is pressed.
The settings are: Delay 4 Sec, Instant-Off.

Run VGABIOS if S3 Resume

This feature allows you to decide the way that VGA BIOS should be called
when the system resumes from an S3 state, if the above feature is set at S3
(PTR) or S1&S3. The options are Auto, Yes, No.

Suspend Mode

When disable d, the system will not enter Suspend mode. The specified
time option defines the idle time the system takes before it enters Suspend
m ode. The options are: Disable, 1, 2, 4, 8, 10, 20, 30, 40 Min, 1 Hour.

Video Off Option

This feature provides the selections of the video display power saving
m ode. The option Suspend - Off allows the video display to go blank if the
system enters Suspend mode. The option All Modes - Off allows the video
display to go blank if the system enters Doze mode or Suspend m ode. The
option Always On allows the video display to stay in Standby mode even
when the system enters Doze or Suspend mode.
The options are: Suspend - Off, All Modes -> Off, Always On.

Video Off Method

The option V/H SYNC+Blank allows the BIOS to turn off the screen dis-
play by turning off the V-Sync and H-Sync signals sent from add-on VGA
card. DPMS Support allows the BIOS to turn off the screen display by
your add-on VGA card which supports DPMS (Display Power Manage­m ent Signaling function). Blank Screen allo ws the BIOS to turn off the
screen display by turning off the red-green-blue signals.
The options are: V/H SYNC+Blank, DPMS Support, Blank Screen.

3 - 16

K8M-800T/M Mainboard Manual

HDD & FDD

When it is set at ON, any access happened at hard drives and floppy drives
will awake the system. The options are: OFF, ON.

PCI Master

To set this feature at ON activates that Power Management feautre (PM)
wake-up event for the PCI bus master card. The options are: OFF, ON.

IRQ/Event Activity Detect

USB Resume from S3

This feature allows you to wake-up the system by USB device when you
save the com puter power at S3. The options are: Enabled, Disabled.

VGA

When set at On, any VGA activity will aThe options are: wake the system.
The options are: OFF, ON.

LPT & COM

When LPT/COM is selected, any access of LPT and COM ports will awake
the system. Likewise, either LPT or COM is chosen, the system will be
awaken by any activity of LPT or COM port.
The options are: LPT/ COM, LPT, COM, NONE.

AC Loss Auto Restart

When the system is shut down due to a power failure, the system will not
power back on by itself. This feature allows you to set the system back to
which power status when the system power is resumed. It will always be
back to on if set at On. The system will always be back to off if set at Off.
The options are Auto, On, Off.

PowerOn by PCI Card

When set at Enabled, any PCI- PM event awakes the system from a PCI-PM
controlled state. The options are Disabled, Enabled.

Wa ke Up On LAN/Ring

When set at Enabled, an input signal coming from another client/server on
the LAN/ring awakes the system from a soft off s tate if connected over
LAN/modem. The options are Disabled or Enabled.

3 - 17

BIOS Setup

Resume Time (hh:mm:ss)

If an ATX power supply is installed and when RTC Alarm Resume is Enabled,
this feature allows you to set the time of the alarm starts when the RTC
Alarm Resume From Soft Off is set to be Enabled.

The options are: hh (

hou r) - 0, 1, 2,.., 23; mm (minu te) - 0, 1, 2,..,59; ss

(second) - 0, 1, 2,..,59.

RTC Alarm Resume

Enabled allows you to set the time the system will be turned on from the
system power-off status. The options are: Enabled, Disabled.

Date (of Month)

This feature allows yo u to set the day of the alarm starts when the RTC
Alarm Resume From Soft Off is set to be Enabled. The options are: 0, 1..31.

IRQs Activity Monitoring

Primary INTR

If set at ON, the Primary interrupt (the Primary option in the feature of IRQ#
Acitivity) will make the power management wake up the system.
The options are: ON, OFF.

IRQ3/../15

After a user-defined time period, the system changes from doze mode to
susp end mode, in which the CPU clock stops and the screen display is
turned off. At this moment, if IRQ activity occurs, the system goes back to
full-on mode directly.
If the IRQ activity which is defined as Non Prim ary takes place, the system
rem ains off until the corresponding IRQ handler finishes. Th e options of
IRQ 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 are: Enabled, Disabled.

3 - 18

K8M-800T/M Mainboard Manual

Resources Controlled By

If set a t Auto, the BIOS arranges all system resources. If there exists a
conflict, select Manual. The options are: Auto (ESCD), Manual.
If Manual is chosen, after the feature IRQ Resources has been pressed,
the I RQ- Assigned To are: PCI Device, Reserved. Whe n resources are
controlled manually, assign each sy stem interrupt a typ e, depending on
which device type uses the interrupt.

PNP OS Installed

If your operating system supports Plug-and-Play, such as Windows NT or
Windows 95, select Yes. The options are: No, Yes.

Reset Configuration Data

Enablin g this, resets the system Exten ded System Configuration Data
(ESCD) when you exit Setup, if you h ave installed a new add-on card and
the system recon figuration has caus ed such a serious conflict that the
operating system can not boot. The options are: Disabled, Enabled.

PCI/VGA Palette Snoop

Set this feature to be enabled if any ISA adapter card installed in the system
requires the VGA palette snoop function.
The options are: Disabled, Enabled.

PnP/PCI Configurations

3 - 19

BIOS Setup

Assign IRQ For VGA

If your PCI VGA card devices do not need an IRQ, select Disabled; there­fore, an IRQ can be released for the system use.
The options are: Enabled, Disabled.

Assign IRQ For USB

If your USB devices do not need an IRQ, select Disabled; therefore, an IRQ
can be released for the system use.
The options are: Enabled, Disabled.

PC Health Status

These items allow end users and technicians to monitor data provided by the
BIOS on this mainboard. They are not user-configurable.

3 - 20

K8M-800T/M Mainboard Manual

Load Optimized Defaults

This submenu is selected for default settings which provide the best system
perform ance.

Supervisor/User Password

To enable the Supervisor/Use r passwords, select the item from the Standard
CMOS Setup. You will be prompted to create your own password. Type your
password up to eight characters and press Enter. You will be asked to confirm
th e pass word. Type the password again and pres s Enter. To disable the
password, press Enter twice when you are prompted to enter a password. A
m essage will appear, confirming the password is disabled.

Spread Spectrum

This feature allows you to disable the spread spectrum.
The options are: Enabled, Disabled.

Auto Detect PCI Clk

When enabled, BIOS will detect the PCI slot slot. If no devices are installed,
the BIOS will auto disable its clock. The options are: Enabled, Disabled.

Frequency/Voltage Control

3 - 21

BIOS Setup

Save and Exit Setup

Afte r you have made changes under Setup, press Esc t o return to the main
m enu. Move the cursor to Save and Exit Setup or press F10 and then press Y to
change the CMOS Setup. If you did not change anything, press Esc again or
m ove the cursor to Exit Without Saving and press Y to retain the Setup settings.
The following message will appear at the center of the screen to allow you to
save data to CMOS and exit the setup utility: SAVE to CMOS and EXIT (Y/N)?

Exit without Saving

If you select this feature, the following message will appear at the center of the
screen to allow you to exit the setup utility without saving CMOS modifications:

Quit Without Saving (Y/N)?

Under the BIOS Feature Setup, if Setup is selected under the Security Option
field and the Supervisor/User Password is enabled, you will be prompted for
the password every time you try to enter the CMOS Setup Utility. If System is
selected and the Supervisor/User Password is enabled, you will be requested
to enter the Password every time you reboot the system or enter the CMOS
Setup utility.

3 - 22

K8M-800T/M Mainboard Manual

Quick Reference

Before Start

This quick reference together with the EZ guide is used for providing you with
the assistance when installing computer system. For detail information, please
read the user manual.

1.

Static electricity may cause damage to the integrated
circuits on the motherboard. Before handling any
motherboard outside of its protective packaging,
ensure that there is no static electric charge in your
body.

2.

Never run the processor without the heatsink properly
and firmly attached. PERMANENT DAMAGE WILL
RESULT!

Package Checklist

If you discover any item below was damaged or lost, please contact your
vendor.

English

1

English

K8M-800T/M Mainboard Manual

Hardware Installation

CPU

1. Swing the lever upword to 90 degree.

2. Install the CPU and make sure the the pin 1

orientation by aligning the socket corner marking
with the socket corner closest to the lever tip. Do
not insert the CPU by force.

Apply some thermal materials on the CPU top;
and install a fan with heatsink that approved by
CPU manufacturer. Affix the CPU by pressing
the lever downward and locking it.

3. Place the fan with heatsink on the CPU top
and press down two plastic clips to hook up with
the holes on the retention module on two sides.

4. Press down the white bar on each clip to
fasten the fan set on the retention module.

2

Memory

1. Locate DDR DIMM sockets on the mainboard.

2. Install DDR DIMM straight down into the

socket 1 using both hands, then socket 2, and so
forth.

3. The clip on both ends of the sock et will close
up to hold the DDR DIMM in place when the
DDR DIMM reaches the socket bottom.

Mounting Mainboard

1.

When using an electric screwdriver, the torque is set
to the allowable range of 5.0 ~ 8.0kg/cm.

2.

Be aware of the shape edges of devices.

Quick Reference

English

1. Locate mounting holes on the mainboard.

2. Place the board over the frame inside the

chassis. Be sure that the board and frame are
aligned.

3. Affix the mainboard by copper columns.

3

English

K8M-800T/M Mainboard Manual

Connecting Devices

1. Locate floppy drive frame and storage on the chassis.

2. Place the drive from the front panel side into

the frame.

3. Affix the drive on the frame by screws.

3. Connect the floppy ribbon cable and power wires. The colored line

on the ribbon cable (pointed by blue arrowhead) must be the same side
with the pin1 of the connector.

Connecting CD/DVD Drive

1. Locate CD/DVD drive frame and storage on the chassis.

2. Place the drive from the front panel side into

the frame.

3. Affix the drive on the frame by screws.

4

Quick Reference

4. Connect the IDE ribbon cable and power wires. The colored line on
the cable (pointed by blue arrowhead) must be the same side with the
pin1 of the connector.

Connecting Hard Drive

1. Locate hard drive frame and storage on the chassis.

2. Place the hard disk drive from the rear of the

frame as the arroaw head indciated.

English

3. Affix the drive on the frame by screws.

4. Connect the IDE ribbon cable and power wires. The colored line on

the cable (pointed by blue arrowhead) must be the same side with the
pin1 of the connector.

5

English

K8M-800T/M Mainboard Manual

Installing Cards

1. Select an available card slot.

2. Remove the slot cover from

chassis.

3. Push the card firmly into the slot. Secure the card with the screw.

Connecting ATX Power

The 20-hole power plug is connected
to ATX power connector. The 4-hole
Power plug is on ATX_12V power
connector.

Assembly System Case

Place the cover on the chassis and
secure the screws on the cover (as
arrow heads pointed) either by a
screw driver or by fingers to tighten
them up.

6

Quick Reference

Attach Peripheral Devices

Link peripheral devices to your system via rear/front panel.

BIOS Setup

English

7

English

K8M-800T/M Mainboard Manual

Standard CMOS Setup

Use the arrow keys to highlight the item and then use PgUp or PgDn
keys to select the value you want in each item.

Load Fail-Safe Defaults

This submenu is selected to diagnose the problem after the computer
boots, if the computer will not boot. These settings do not give optimal
performance.

Driver Installation

Drivers

Place your lst Utilities CD into your CD Drive. The top menu will
appear on the screen. Select the item Drivers to start the auto running
feature.

Help

The item provides you with some information about the features and
drivers. Reading it will be helpful on installation.

Software Bundle

The item provides you with some useful software tools to assist you to
manage your computer system.

8

s

l

Guide de référence rapide

Avant de commencer

Le présent guide de référence facile et le guide EZ ont pour but de vous aider à
installer votre système informatique. Pour des informations plus détaillées,
veuillez vous reporter au manuel de l'utilisateur.

1.

L'électricité statique risque d'endommager les circuits
intégrés sur la carte mère. Avant de sortir une carte
mère de son emballage protecteur, vérifiez que vous
n'êtes pas porteur d'une charge d'électricité statique.

2.

Ne jamais utilisé le processeur sans avoir installé
correctement et solidement un dissipateur de chaleur.
CELA RISQUERAIT DE CAUSER DES
DOMMAGES IRREVERSIBLES !

Liste de contrôle du paquet

Si vous vous rendez compte que l'un de ces éléments est manquant ou
endommagé, prenez immédiatement contact avec votre revendeur.

Français

Carte mère Câble pour

Protection E/S Manue

Support 1394 avec
câble (optionnel)

lecteur de

disquettes

SATA (haut)

Câble données SATA

Câble ruban

IDE 80

broche

Pilotes

Câble alimentation

Câble USB

(optionnel)

1

Français

Manuel de la carte mère K8M-800T/M

Installation de l'équipement

Microprocesseur :

1. Faites pivoter le levier vers le haut de 90
degrés.

2. Installez le microprocesseur et vérifiez
l'orientation de la broche 1 en alignant le coin
marqué du socle avec le coin du socle le plus près
de la pointe du levier. Ne pas forcer lors de
l'insertion du microprocesseur.

Appliquez des matériaux thermiques au sommet
du microprocesseur ; et installez un ventilateur
avec dissipateur de chaleur agréé par le fabricant
du microprocesseur. Fixez le microprocesseur en
position en abaissant le levier et en le
verrouillant.

3. Placez le ventilateur avec dissipateur de
chaleur sur le microprocesseur et appuyez sur les
deux clips en plastique pour les enclencher dans
les orifices sur le module de rétention sur les
deux côtés.

4. Appuyez sur la barre blanche sur chaque clips
pour fixer l'ensemble de ventilation sur le module
de rétention.

2

Guide de référence rapide

Mémoire

1. Repérez les emplacements DDR DIMM sur la carte
mère.

2. Installez un module DDR DIMM directement
dans le socle 1 en vous servant de vos deux
mains, puis dans le socle 2, et ainsi de suite.

3. Les clips situés aux deux extrémités du socle
se refermeront pour maintenir le module DDR
DIMM en position lorsque le module DDR
DIMM atteindra la base du socle.

Montage de la carte mère

1.

Lorsque vous utilisez un tournevis électrique, la
torsion doit être réglée entre 5,0 et 8,0kg/cm.

2.

Faites attention aux bords tranchants des éléments.

1. Repérez les orifices de montage sur la carte
mère.

2. Placez la carte au-dessus du cadre dans la
châssis. Vérifiez que la carte et le cadre sont bien
alignés.

Français

3. Fixez la carte mère à l'aide des plots en cuivre.

3

Français

Manuel de la carte mère K8M-800T/M

Branchement de périphériques

1. Repérez le cadre pour lecteur de disquettes et pour
disque dur sur le châssis.

2. Placez l'unité dans le cadre en l'insérant par le
panneau avant.

3. Fixez l'unité sur le cadre avec des vis.

4. Connectez le câble ruban et les fils d'alimentation du lecteur de

disquettes. La ligne colorée du câble ruban (indiquée par une flèche
bleue) doit être du même côté que la broche 1 du connecteur.

Connexion d'un lecteur de CD/DVD

1. Repérez le cadre pour unité CD/DVD sur le châssis.

2. Placez l'unité dans le cadre en l'insérant par le

panneau avant.

3. Fixez l'unité sur le cadre avec des vis.

4

Guide de référence rapide

4. Connectez le câble ruban IDE et les fils d'alimentation. La ligne
colorée du câble (indiquée par une flèche bleue) doit être du même
côté que la broche 1 du connecteur.

Connexion du Disque dur

1. Repérez le cadre pour unité de disque dur sur le châssis.

2. Placez le disque dur en l'insérant à l'arrière du

cadre ainsi qu'indiqué par la flèche.

Français

3. Fixez l'unité sur le cadre avec des vis.

4. Connectez le câble ruban IDE et les fils d'alimentation. La ligne

colorée du câble (indiquée par une flèche bleue) doit être du même
côté que la broche 1 du connecteur.

5

Français

Manuel de la carte mère K8M-800T/M

Installation des cartes

1. Sélectionnez un emplacement disponible pour carte.

2. Démontez le capot d'emplacement

du châssis.

3. Poussez fermement la carte dans l'emplacement. Fixez la carte
avec la vis.

Connexion de l'unité d'alimentation ATX

La prise d'alimentation 20 orifices
sert à connecter le connecteur de
l'unité d'alimentation ATX. La prise
d'alimentation 4 orifices sert à
brancher le connecteur
d'alimentation ATX_12V.

Montage du boîtier système

Placez le capot sur le châssis et fixez
à l'aide des vis sur le capot (ainsi
qu'indiqué par les flèches), soit avec
un tournevis soit avec les doigts, et
serrez-les.

6

Guide de référence rapide

Branchement d'équipements périphériques

Vous pouvez brancher des équipements périphériques sur le
panneau arrière ou avant de votre système.

Français

Câble

alimentation

système

Clavier PS/2

Module mémoire

flash USB

Manette de

jeux

Configuration BIOS

Sur prise LAN

Souris
PS/2

Imprimante

Moniteur

Haut-parleurs

7

Français

Manuel de la carte mère K8M-800T/M

Configuration CMOS standard

Utilisez les touches fléchées pour sélectionner l'élément voulu et
utilisez les touches Pages préc. et Page suiv. pour sélectionner la valeur
voulue pour chaque élément.

Chargement des valeurs de sécurité (Fail-Safe) par défaut

Ce menu secondaire est utilisé pour diagnostiquer un problème apparu
au démarrage de l'ordinateur, si l'ordinateur ne démarre pas. Ces
réglages ne permettent pas d'avoir des performances optimales.

Installation des pilotes

Pilotes

Placez le premier CD utilitaires dans votre lecteur de CD. Le menu
principal s'affichera à l'écran. Sélectionnez l'élément Pilotes pour lancer
la fonction d'exécution automatique.

Aide

Cette option vous donne des informations concernant les fonctions et
les pilotes. Lisez attentivement car cela vous aidera pour l'installation.

Logiciels d'accompagnement

Cette option vous permet d'avoir des outils logiciels utiles qui vous
aideront à générer votre système informatique.

8

g

Kurzanleitung

Bevor Sie beginnen

Diese Kurzanleitung zusammen mit dem EZ-Handbuch unterstützt Sie bei der
Installation des Computersystems. Details entnehmen Sie bitte dem Handbuch.

1.

Statische Elektrizität kann die integrierten
Schaltungen auf dem Motherboard beschädigen.
Bevor Sie ein Motherboard aus seiner Schützhülle
herausnehmen, sollten Sie sicherstellen, dass sich
keine statische Elektrizität auf Ihrem Körper befindet.

2.

Betreiben Sie den Prozessor nie ohne richtig und fest
angebrachtem Kühlkörper. EINE PERMANENTE
BESCHÄDIGUNG IST DIE FOLGE!

Prüfen des Kartoninhalts

Müssen Sie feststellen, dass eines der folgenden Gegenstände beschädigt ist
oder fehlt, dann kontaktieren Sie bitte Ihre Verkaufsstelle.

Deutsch

Mainboard Kabel des

E/A-Abschirmun

1394-Halter mit Kabel
(optional)

Diskettenlaufwerks

Anleitung Treiber

SATA-Neztkabel (oben)
SATA-Datenkabel (unten)
(optional)

80-pol. IDE­Flachbandkabel

USB-Kabel
(optional)

1

Deutsch

Handbuch

Installation der Hardware

CPU

1. Ziehen Sie den Hebel bis 90 Grad nach oben.

2. Installieren Sie die CPU und achten Sie dabei

darauf, das der Stift 1 mit der Markierung auf der
Sockelecke, die der Hebelspitze am nächsten
liegt, ausgerichtet ist. Stecken Sie die CPU nicht
gewaltsam hinein.

Tragen Sie auf der CPU einige thermische
Materialien auf; installieren Sie auch einen Lüfter
mit Kühlkörper, der vom CPU-Hersteller
genehmigt ist. Befestigen Sie die CPU, indem
Sie den Hebel herunterdrücken und sie dadurch
verriegeln.

3. Legen Sie den Lüfter mit Kühlkörper auf die
CPU und drücken Sie die zwei Plastikklemmen
herunter, damit sie in die Löcher auf beiden
Seiten des Retentionsmoduls einhaken.

4. Drücken Sie weiße Leiste auf jedem Clip nach
unten, um das Lüfterset am Retentionsmodul zu
befestigen.

2

Arbeitsspeicher

1. Finden Sie die DDR-DIMM-Sockel auf dem
Mainboard.

2. Stecken Sie das DDR-DIMM mit beiden
Händen gerade nach unten in den Sockel 1
hinein, dann in Sockel 2, usw.

3. Die Klemme an beiden Enden des Sockels
schließt sich, um das DDR-DIMM festzuhalten,
wenn das DDR-DIMM den Sockelboden
erreicht.

Einbauen des Mainboards

1.

Bei Verwendung eines elektrischen Schraubenziehers
sollten Sie das Drehmoment auf 5,0 ~ 8,0 kg/cm
einstellen.

2.

Achten Sie auf scharfe Gerätekanten.

1. Finden Sie die Befestigungslöcher auf dem
Mainboard.

2. Legen Sie das Mainboard auf den Rahmen im
Gehäuseinnern. Achten Sie darauf, dass das
Mainboard und der Rahmen miteinander
ausgerichtet sind.

Kurzanleitung

Deutsch

3. Befestigen Sie das Mainboard mit
Kupferstützen.

3

Deutsch

Handbuch

Anschließen von Geräten

1. Finden Sie den Rahmen und die Aufnahme des
Diskettenlaufwerks am Gehäuse.

2. Schieben Sie das Laufwerk von der
Vorderseite in den Rahmen hinein.

3. Befestigen Sie das Laufwerk mit Schrauben
am Rahmen.

4. Schließen Sie das Flachbandkabel und die Leitungsdrähte des
Diskettenlaufwerks an. Die farbige Linie auf dem Flachbandkabel (mit
blauem Pfeilkopf) muss sich auf der gleichen Seite befinden, wie Stift
1 des Anschlusses.

Anschließen eines CD/DVD-Laufwerks

1. Finden Sie den Rahmen und die Aufnahme des CD/DVD­Laufwerks am Gehäuse.

2. Schieben Sie das Laufwerk von der
Vorderseite in den Rahmen hinein.

3. Befestigen Sie das Laufwerk mit Schrauben
am Rahmen.

4

Kurzanleitung

4. Schließen Sie das IDE-Flachbandkabel und die Leitungsdrähte an.
Die farbige Linie auf dem Flachbandkabel (mit blauem Pfeilkopf)
muss sich auf der gleichen Seite befinden, wie Stift 1 des Anschlusses.

Anschließen einer Festplatte

1. Finden Sie den Rahmen und die Aufnahme der Festplatte am
Gehäuse.

2. Schieben Sie die Festplatte von der Rückseite
des Rahmens hinein, wie der Pfeilkopf anzeigt.

Deutsch

3. Befestigen Sie das Laufwerk mit Schrauben
am Rahmen.

4. Schließen Sie das IDE-Flachbandkabel und die Leitungsdrähte an.
Die farbige Linie auf dem Flachbandkabel (mit blauem Pfeilkopf)
muss sich auf der gleichen Seite befinden, wie Stift 1 des Anschlusses.

5

Deutsch

Handbuch

Installieren von Karten

1. Wählen Sie einen verfügbaren Kartensteckplatz aus.

2. Entfernen Sie die Abdeckung des

Steckplatzes vom Gehäuse.

3. Stecken Sie die Karte fest in den Steckplatz hinein. Befestigen Sie
die Karte mit der Schraube.

Anschließen des ATX-Netzteils

Der Netzstecker mit 20 Löchern wird
mit dem ATX-Netzanschluss
verbunden. Der Netzstecker mit 4
Löchern wird mit dem ATX_12V­Netzanschluss verbunden.

Montieren des Systemgehäuses

Setzen Sie die Abdeckung auf das
Gehäuse und ziehen Sie die
Schrauben auf dem Gehäuse (in
Pfeilrichtung) mit einem
Schraubenzieher oder mit Ihren
Fingern fest an.

6

Kurzanleitung

Anschließen von Peripheriegeräten

Schließen Sie Peripheriegeräte über die Rück-/Vorderseite an Ihr
System an.

Deutsch

System-

Netzkabel

PS/2-Tastatur

USB-Flasch-

Speichermodul

Joystick

BIOS-Setup

PS/2-Maus

Drucker

Monitor

Zur LAN-Buchse

Lautsprecher

7

Deutsch

Handbuch

Standard CMOS Setup

Markieren Sie den Menüpunkt mit den Pfeiltasten und wählen Sie den
Wert für jeden Punkt mit den Tasten Bild-Nach-oben oder Bild-Nach­unten aus.

Load Fail-Safe Defaults

Dieses Untermenü dient zur Diagnose des Computers, wenn er nicht
richtig startet. Diese Einstellungen liefern keine optimale
Systemleistung.

Treiberinstallation

Drivers

Legen Sie die 1. Utility-CD in das CD-Laufwerk. Das obere Menü
erscheint im Bildschirm. Wählen Sie den Punkt Drivers, um die
automatische Treiberinstallation einzuleiten.

Help

Dieser Punkt informiert Sie über die Funktionen und die Treiber. Er ist
sehr hilfreich bei der Installation.

Software Bundle

Dieser Punkt verfügt über einige nützliche Software-Werkzeuge, die
Sie bei der Verwaltung Ihres Computersystems unterstützen.

8

Consultazione rapida

Prima di iniziare

Questa Guida di consultazione rapida insieme alla Guida facile è utilizzata per
fornire assistenza durante l’installazione del sistema PC. Per informazioni
dettagliate si prega di fare riferimento al Manuale utente.

1.

L’elettricità statica può provocare danni ai circuiti
integrati della scheda madre. Prima di maneggiare
qualsiasi scheda madre senza la confezione di
protezione, assicurarsi che il proprio corpo non abbia
accumulato elettricità statica.

2.

Non fare funzionare mai il processore senza che il
dispersore di calore sia collegato in modo corretto ed
appropriato. SI POSSONO PRVOCARE DANNI
PERMANENTI!

Contenuto della confezione

Mettersi in contato con il rivenditore se qualsiasi dei seguenti elementi manca o
è danneggiato.

Italiano

Scheda madre Cavo unità

Schermatura I/O Manuale Driver

Staffa 1394 con

cavo (optional)

dischetti

Staffa SATA con cavo

(optional)

Cavo a nastro
IDE ad 80 pin

Cavo USB

(optional)

1

Italiano

Manuale scheda madre K8M-800T/M

Installazione dell’hardware

CPU

1. Spostare la levetta in lato di 90 gradi.

2. Installare la CPU e controllare l’orientamento

del pin 1 allineando il contrassegno sull’angolo
della presa con il contrassegno più vicino alla
punta della levetta. Non forzare la CPU.

Applicare dei materiali termici sulla parte
superiore della CPU ed installare una ventolina
con dispersore di calore che sia approvata dal
produttore della CPU. Bloccare la CPU
spingendo verso il basso la levetta e bloccandola.

3. Mettere la ventolina con il dispersore di calore
sulla parte superiore della CPU e premere verso il
basso i due fermagli di plastica per agganciare i
fori sui due lati del modulo di trattenimento.

4. Premere verso il basso la levetta bianca su
ciascun fermaglio per fissare il gruppo ventolina
sul modulo di trattenimento.

2

Riferimento rapido

Memoria

1. Ubicare gli alloggiamenti DIMM DDR sulla scheda
madre.

2. Installare i moduli DIMM DDR spingendoli
con entrambe le mani verso il basso nella presa 1,
poi la 2, e così avanti.

3. I fermagli su entrambi i lati della presa
fisseranno e bloccheranno i moduli DIMM DDR
quando raggiungono il fondo dell’alloggiamento.

Montaggio della scheda madre

1.

Quando si utilizza un cacciavite elettrico, la torsione
va impostata tra i 5 e gli 8 kg/cm.

2.

Prestare attenzione alle estremità affilate dei
dispositivi.

1. Ubicare i fori di montaggio sulla scheda
madre.

2. Mettere la scheda sulla cornice all’interno del
telaio. Assicurarsi che la scheda e la cornice
siano allineate.

Italiano

3. Fissare la scheda madre con le barre di rame.

3

Italiano

Manuale scheda madre K8M-800T/M

Collegamento dei dispositivi

1. Ubicare la cornice e l’alloggiamento dell’unità
dischetti sul telaio.

2. Inserire l’unità dalla parte frontale del telaio.

3. Fissare l’unità alla cornice con le viti.

4. Collegare il cavo a nastro ed i cavi d’alimentazione La riga colorata

sul cavo anastro (freccia blu) deve trovarsi nella stessa direzione con il
pin1 del connettore.

Collegamento dell’unità CD / DVD

1. Ubicare la cornice e l’alloggiamento dell’unità CD/DVD sul
telaio.

2. Inserire l’unità dalla parte frontale del telaio.

3. Fissare l’unità alla cornice con le viti.

4

Riferimento rapido

4. Collegare il cavo IDE ed i cavi d’alimentazione La riga colorata sul
cavo (freccia blu) deve trovarsi nella stessa direzione con il pin1 del
connettore.

Collegamento del disco rigido

1. Ubicare la cornice e l’alloggiamento dell’unità disco rigido sul
telaio.

2. Inserire il disco rigido dalla parte posteriore
della cornice come indica la freccia.

Italiano

3. Fissare l’unità alla cornice con le viti.

4. Collegare il cavo IDE ed i cavi d’alimentazione La riga colorata sul

cavo (freccia blu) deve trovarsi nella stessa direzione con il pin1 del
connettore.

5

Italiano

Manuale scheda madre K8M-800T/M

Installazione delle schede

1. Selezionare un alloggiamento scheda disponibile.

2. Rimuovere la copertura

dell’alloggiamento dal telaio.

3. Spingere con fermezza la scheda nell’alloggiamento. Fissare la
scheda con le viti.

Collegamento alimentazione ATX

La presa di corrente a 20 fori è
collegata al connettore alimentazione
ATX. La presa di corrente a 4 fori è
collegata al connettore ATX_12V.

Assemblaggio del sistema

Mettere la copertura sul telaio e
fissare le viti sulla copertura (come
mostrato dalle frecce) con un
cacciavite o con le dita.

6

Riferimento rapido

a

Collegamento delle periferiche

Collegare le periferiche al sistema tramite il pannello frontale /
posteriore.

Italiano

Cavo

alimentazione

sistem

Tastiera PS/2

Modulo memoria

Flash USB

Joystick

Impostazione BIOS

Mouse
PS/2

Stampante

Monitor

Al connettore LAN

Casse

7

Italiano

Manuale scheda madre K8M-800T/M

Standard CMOS Setup

Utilizzare le frecce per evidenziare la voce ed utilizzare i tasti PgUp o
PgDn per selezionare il valore desiderato per ciascuna voce.

Load Fail-Safe Defaults

Questo menu secondario è selezionato per diagnosticare il problema
dopo il riavvio del computer, se il computer non si avvia. Queste
impostazioni non forniscono le prestazioni ottimali.

Installazione del driver

Driver

Inserire il primo CD utilità nell’unità CD-ROM. Sullo schermo del
computer apparirà il menu d’installazione. Selezionare la voce Drivers
per avviare la funzione d’esecuzione automatica.

Help

Questa voce fornisce alcune informazioni sulle funzioni e sui driver. La
sua lettura è utili per l’installazione.

Software Bundle

Questa voce fornice alcuni utili strumento software per assistervi nella
gestione del sistema PC.

8

Referencia rápida

Antes de comenzar

Esta referencia rápida junto con la guía EZ se usan para ofrecerle asistencia al
instalar el sistema en su ordenador. Para más información, lea el manual del
usuario.

1.

La electricidad estática puede causar daños a los
circuitos integrados de la placa base. Antes de
manipular la placa base fuera de su bolsa protectora,
asegúrese de que su cuerpo no esta cargado con
electricidad estática.

2.

Nunca ponga el procesador en funcionamiento sin
adjuntar firmemente el disipador. ¡PODRÍAN
OCURRIR DAÑOS PERM ANENTES!

Lista de Comprobación de Paquete

Si descubre que falta algún elemento o está dañado, póngase en contacto con su
distribuidor.

Español

Placa Base Cable de unidad de

Blindaje E/S Manual Controladores

conector 1394 con cable
(opcional)

disco flexible

Cable de alimentación SATA

(Superior)

Cable de datos SATA (inferior)

(opcional)

Cable IDE de 80 pin

Cable USB
(opcional)

1

Español

Manual de la Placa Base Dynasty K8M-800T/M

Instalación de hardware

CPU

1. Deslice la palanca hasta 90 grados.

2. Instale la CPU y asegúrese de que la

orientación del pin 1 está alineada con la esquina
más cercana a la punta de la palanca. No fuerce la
inserción de la CPU.

Aplique algo de material térmico en la parte
superior de la CPU e instale un ventilador con
disipador aprobado por el fabricante de la CPU.
Fije la CPU presionando la palanca hacia abajo y
bloqueándola.

3. Coloque el ventilador con el disipador en la
parte superior de la CPU y enganche los dos
ganchos de plástico en el módulo de retención
por los dos lados.

4. Presione la barra blanca en cada gancho para
asegurar el ventilador en el módulo de retención.

2

Referencia rápida

Memoria

1. Localice las ranuras DIMM DDR en la placa base.

2. Installe los DIMM DDR en las ranura 1

usando ambas manos, después en la ranura 2, y
así continuamente.

3. Se cerrarán ambos extremos de la ranura para
sostener el DIMM DDR en su lugar cuando el
DIMM DDR llegue al fondo de la ranura.

Montaje de la Placa Base

1.

Si usa un destornillador eléctrico, debe ajustar la
fuerza en el rango de 5.0 ~ 8.0kg/cm.

2.

Tenga cuidado con los lados afilados de los
dispositivos.

1. Localice los agujeros de montaje en la placa
base.

Español

2. Coloque la placa en su lugar en la caja.
Asegúrese de que la placa y la caja están
alineadas.

3. fije la placa base con las barras de cobre.

3

Español

Manual de la Placa Base Dynasty K8M-800T/M

Conexión de los dispositivos

1. Localice los huecos de la unidad de disco flexible y
unidades de almacenamiento en la caja.

2. Coloque la unidad desde el lado del panel
frontal en el hueco.

3. Fije la unidad en el hueco con los tornillos.

4. Conente el cable de la unidad y los cables de alimentación. La linea

de color en el cable (señalada con una flecha azul) debe estar en el
mismo lado que el pin1 del conector.

Conexión de unidad de CD/DVD

1. Localice los huecos de la unidad de CD/DVD y unidades de
almacenamiento en la caja.

2. Coloque la unidad desde el lado del panel
frontal en el hueco.

3. Fije la unidad en el hueco con los tornillos.

4

Referencia rápida

4. Conecte el cable IDE de la unidad y los cables de alimentación. La
linea de color en el cable (señalada con una flecha azul) debe estar en
el mismo lado que el pin1 del conector.

Conexión del Disco Duro

1. Localice los huecos de disco duro en la caja.

2. Coloque el disco duro desde la parte trasera

como indica la flecha.

Español

3. Fije la unidad en el hueco con los tornillos.

4. Conecte el cable IDE de la unidad y los cables de alimentación. La

linea de color en el cable (señalada con una flecha azul) debe estar en
el mismo lado que el pin1 del conector.

5

Español

Manual de la Placa Base Dynasty K8M-800T/M

Instalación de Tarjetas

1. Seleccione una ranura de tarjeta disponible.

2. Quite la cubierta de la ranura del

chasis.

3. Presione la tarjeta firmemente en la ranura. Asegure la tarjeta con
el tornillo.

Conexión de la alimentación ATX

El conector de 20 agujeros se
conecta al conector de energía ATX.
El enchufe de 4 agujeros se conecta
al conector de energía ATX_12V.

Ensamblaje de la Caja del Sistema

Coloque la cubierta en la caja y
asegure los tornillos en la cubierta
(como muestran las flechas) con un
destornillador o con los dedos.

6

Referencia rápida

Conexión de Dispositivos Periféricos

Conecte los dispositivos periféricos al sistema por madio del panel
trasero/frontal.

Español

Cable de

alimentación del

sistema

Teclado PS/2

Módulo de Memoria

Flash USB

Joystick

Configuración BIOS

Ratón PS/2

Impresora

Monitor

Al conector LAN

Altavoz

7

Español

Manual de la Placa Base Dynasty K8M-800T/M

Configuración CMOS estándar

Use las teclas de cursor para resaltar el elemento y usar las teclas
AvPág y RePág para seleccionar el valor que desee para cada elemento.

Cargar opciones predeterminadas

Puede seleccionar este submenú para diagnosticar el problema después
de que inicie el ordenador, si el ordenador no ha iniciado correctamente.
Estas opciones no son necesariamente las óptimas.

Instalación de controladores

Controladores

coloque su CD de controladores en la unidad de CD. Aparecerá el
menú superior en la pantalla. Seleccione los Controladores para iniciar
la función de ejecución automática.

Ayuda

Le ofrece informaciónacerca de las funciones y controladores. Si la lee
encontrará ayuda para la instalación.

Paquete de software

Este elemento le ofrece algunas herramientas útiles para ayudarle a
administrar su sistema.

8

クイックリファレンス

始める前に

このクイックリファレンスをEZガイドと共に使用すると、コンピュータシステ
ムを簡単にインストールすることができます。詳細は、ユーザーマニュアルをお

読みください。

1.

静電気は、マザーボードの統合回路を損傷する原因と
なります。保護包装の外側でマザーボードを扱う前
に、身体に静電気が帯電していないことを確認してく
ださい。

2.

ヒートシンクを適切にしっかり取り付けていない状態
では、プロセッサを決して作動しないでください。永
久的な損傷の原因となります!

梱包のチェックリスト

付属品が足りないときは破損しているときは、ベンダーに連絡してください。

日本語

メインボード

I/O シールド マニュアル

ケーブル付き 1394 ブラ

フロッピードライブケ
ーブル

ケーブル付き SATA

（オプション）

80 ピン IDE リボンケー

ブル

ドライバ

USB ケーブル

1

日本語

K8M -800T/M メインボードマニュアル

ハードウェアの取り付け

CPU

1. レバーを90度上に回します。

2. CPUを取付け、ソケットの隅のマーキング

をレバーチップのすぐ傍のソケットの隅に
合わせて、ピン1の方向を確認します。無理
にCPUを差し込まないでください。

CPUの上に感熱糊を塗り、CPUメーカーが承
認したヒートシンクの付いたファンを取り
付けます。レバーを下方向に押してCPUを固
定したら、ロックします。

3. ヒートシンクの付いたファンをCPUの上
に配置し、2本のプラスチックのチップを押
し下げて、両側のリテンションモジュール
に取り付けます。

4. 白いバーを各クリップに押し下げて、リ
テンションモジュールにファンセットを固
定します。

2

クイックリファレンス

日本語

メモリ

1. マザーボードで、DDR DIMMソケットを探します。

2. 両手を使用してDDR DIMMをソケット1、

ソケット2といった具合に、真下に押して取
り付けます。

3. ソケットの両端のクリップを閉じると、
DDR DIMMがソケット下部に達したときに、

DDR DIMMは適切な場所に固定されます。

メインボードのマウント

1.

電動ネジ回しを使用するとき、トルクは5.0 ~

8.0kg/cmの許容範囲に設定されます。

2.

デバイスの端に注意してください。

1. メインボードでマウンティングホールを
探します。

2. ボードをシャーシ内部のフレームの上に
取り付けます。ボードとフレームの位置が
あっていることを確認してください。

3. 銅の支柱メインボードでメインボードを
固定します。

3

日本語

K8M -800T/M メインボードマニュアル

デバイスの接続

1. シャーシでフロッピードライブのフレームと記
憶装置を探します。

2. フロントパネルのサイドのドライブをフ
レームに取り付けます。

3. ネジでフレームにドライブを取り付けま
す。

4. フロッピーリボンケーブルと電源ワイヤを接続します。リボ
ンケーブルの色の付いた線（青い矢印でポイント）は、コネク
タのピン1と同じ側にある必要があります。

CD/DVD

ドライブの接続

1. シャーシでCD/DVDドライブのフレームと記憶装置を探します。

2. フロントパネルのサイドのドライブをフ

レームに取り付けます。

3. ネジでフレームにドライブを取り付けま
す。

4

クイックリファレンス

4. IDEリボンケーブルと電源ワイヤを接続します。ケーブルの
色の付いた線（青い矢印でポイント）は、コネクタのピン1と
同じ側にある必要があります。

ハードドライブの接続

1. シャーシでハードドライブのフレームと記憶装置を探します。

2. 矢印が示すように、フレームの背面のハ

ードディスクドライブを取り付けます。

日本語

3. ネジでフレームにドライブを取り付けます。

4. IDEリボンケーブルと電源ワイヤを接続します。ケーブルの

色の付いた線（青い矢印でポイント）は、コネクタのピン1と
同じ側にある必要があります。

5

日本語

K8M -800T/M メインボードマニュアル

カードの取り付け

1. 開いているカードスロットを選択します。

2. シャーシからスロットカバーを

取り外します。

3. カードをスロットにしっかりと押します。ネジでカードを
固定します。

ATX

電源の接続

20穴の電源プラグを、ATX電源
コネクタに接続します。4穴の
電源プラグをATX_12V電源コ
ネクタに接続します。

アセンブリシステムケース

シャーシのカバーを取り付け、ね
じ回しか指でカバーのネジを（矢
印がポイントするように）回して
締め付けます。

6

クイックリファレンス

日本語

周辺装置の取り付け

背面/前面パネルによって、システムに周辺装置を結合します。

システム電源ケ
ーブ

PS/2キーボード

USB フラッシュメモ

リモジュール

ジョイスティッ
ク

LAN ジャックへ

PS/2マウス

プリンタ

モニタ

スピーカー

BIOS のセットアップ

7

日本語

K8M -800T/M メインボードマニュアル

標準CMOSのセットアップ

矢印キーを使用してアイテムを強調表示し、PgUp または PgDn
キーを使って、各アイテムに希望する値を選択します。

フェールセーフデフォルトのロード
このサブメニューは、コンピュータが起動しても、コンピュー

タが起動しない場合の問題を診断するために選択します。これ
らの設定は、最適のパフォーマンスを提供しません。

ドライバのインストール

ドライバ

CDドライブに最初のユーティリティCDを挿入します。画面に
トップメニューが表示されます。アイテムのドライバを選択し、
自動実行機能を開始します。

ヘルプ

このアイテムは、機能とドライバに関する一部の情報を提供し
ます。この情報を読めば、インストールを簡単に行うことがで
きます。

ソフトウェアバンドル

このアイテムは役に立つソフトウェアツールを提供して、コン
ピュータシステムの管理を容易にします。

8

線

快速參考指南

開始之前

本快速參考指南和 EZ 指南可以幫助您安裝電腦系統。有關的詳細資訊，
請閱讀用戶手冊。



1.

靜電可能會損壞主板上的積體電路。從保護袋中
取出主板進行操作時，應確保身上沒有靜電。

2.

在沒有正確牢固地安裝散熱片之前，切勿運行處
理器。否則，可能導致永久損壞！

包裝物品清單

如果下列任何物品損壞或缺失，請與經銷商聯繫。

繁體中文

主板 80-針 IDE 帶

I/O 護蓋

1394 線板和帶線

（選件）

軟碟驅動器帶

手册

SATA 電源線（上）
SATA 資料線（下）

（選件）

線

驅動程式

USB 線

（選件）

1

繁體中文

K8M-800T/M 主機板手册

安裝硬體

CPU

1. 將鎖杆向上擡起 90 度。

2. 安裝 CPU，將插座拐角標記對準距離鎖杆

頂端最近的插座拐角，確保管腳 1 的方向正
確。不要用力插入 CPU。

在 CPU 上面塗上一層熱物質；然後安裝經過
CPU 製造商認可的帶散熱片的風扇。向下按
鎖杆並鎖緊以固定 CPU。

3. 將帶散熱片的風扇放在 CPU 上面，然後
向下按兩個塑膠夾以鈎住支撐塊兩側的孔。

4. 向下按每個塑膠夾上的白色扳杆，將風扇
套件固定到支撐塊上。

2