Fibaro FGR-222 Operating Manual

ENG

OPERATING MANUAL

FIBARO ROLLER SHUTTER 2

FGR-222-EN-A-v1.2

FIBARO Roller Shutter 2 is a universal, Z-Wave compatible, electric motor controller. The device allows for controlling motors of roller blinds, awnings, venetian blinds, gates and others, which are single phase AC powered. FIBARO Roller Shutter 2 allows for precise positioning of a roller blind or venetian blind slats. Precise positioning is available for the motors equipped with mechanic and electronic end switches. The module may be controlled wirelessly, through the Z-Wave network main controller, or through the switch keys connected to it. It’s also possible to combine few devices into groups of devices, which then can be controlled simultaneously. In addition, FIBARO Roller Shutter 2 is equipped with Power Metering.

I. SPECIFICATIONS

Power supply:

Power consumption:

Operational temperature:

Dimensions (L x W x H):

For installation in boxes:

Rated load current:

Active element:

Type of supported motor:

Supported limit switches type:

Device control:

Radio protocol:

Radio signal power:

Radio Frequency:

Range:

Comply with EU directives:

II. TECHNICAL INFORMATION

• Controlled by FIBARO system devices or any Z-Wave controller.

• FIBARO Roller Shutter 2 is an extension unit.

• Microprocessor control.

• Active element: electromagnetic, micro-gap relay switch.

• The device may be operated by momentary or toggle switches, and by dedicated roller blind control switches.

• Connected motor’s current and historical power consumption measured.

• To be installed in wall switch boxes of dimensions allowing for

installation, conforming to provisions of applicable regulations.

110 - 240 V AC 50 - 60 Hz

to 0,8 W

0 - 35°C

42,5 x 38,25 x 20,3 mm

Ø ≥ 50mm, depth ≥ 60mm

4,2 A for lamps and resistive loads 1,7 A for motors with compensated

power factor (inductive loads)

micro-gap relay switch μ

single-phase AC motors

electronic and mechanic

remotely - radio waves directly - push buttons

Z-Wave

1mW

868,4 MHz EU; 908,4 MHz US; 921,4 MHz ANZ; 869,0 MHz RU;

up to 50 m outdoors up to 30 m indoors (depending on building materials)

RoHS 2011/65/EU RED 2014/53/EU

III. SUPPORTED LOADS

110-240 V~FGR-222

4,2 A

lamp and resistive load

inductive load

IV. GENERAL INFORMATION ABOUT FIBARO SYSTEM

FIBARO is a wireless smart home automation system, based on the Z-Wave protocol. All of available devices can be controlled through a computer (PC or Mac), smartphone or tablet. Devices are not only receivers, but can also repeat the signal, increasing the Z-Wave network’s range. It gives advantage over traditional wireless systems that require direct link between transmitter and receiver, as a result the construction of the building could affect network’s range negatively.

Every FIBARO network has its unique identification number (home ID). Multiple independent networks can exist in the building without interfering. Transmission security of FIBARO System is comparable to wired systems.

Z-Wave technology is the leading solution in smart home automation. There is a wide range of Z-Wave devices that are mutually compatible, independently of manufacturer. It gives the system the ability to evolve and expand over time. For more information visit: www.fibaro.com.

V. ROLLER SHUTTER INSTALLATION

CAUTION Read this manual before attempting to install the device! Failure to observe recommendations

included in this manual may be dangerous or cause a violation of the law. The manufacturer, Fibar

Group S.A., will not be held responsible for any loss or damage resulting from not following the instructions of operating manual.

DANGER Danger of electrocution! All works on the device

may be performed only by a qualified and licensed electrician. Observe national regulations. Faulty connection or use may result in fire or electric shock.

DANGER Danger of electrocution! Even when the device is

turned off, voltage may be present at its terminals. Any works introducing changes into the configuration of connections or the load must be always performed with disconnected voltage (disable the fuse).

DANGER

Any maintenance work on controlled devices may be performed only after the power supply has been disconnected.

CAUTION

It’s not recommended to operate all of the roller blinds simultaneously. For safety reasons, at least one roller blind should be controlled independently,

providing safe escape route in case of emergency.

CAUTION

Do not connect the device to loads exceeding recommended values. Connect only in accordance with the diagram presented in the manual.

Improper connections may be dangerous.

1. Before installation make sure the voltage supply is disconnected.

2. Connect the Roller Shutter in accordance with the wiring diagram presented on Fig. 1 (roller blinds, venetian blinds) or Fig. 2 (gates).

3. Place the device in a switch box.

4. Arrange the antenna (tips presented below Fig. 3)

5. Turn on the power supply keeping the necessary safety

precautions.

6. Include the module into the Z-Wave network, observing pt. VI description.

7. If necessary, calibrate the module, observing pt. IX descripion.

1,7 A

L NS1S2

Fibaro Roller

Shutter

Fig. 1 Roller Shutter wiring diagram

sensor

switches

safety switch

limit

L NS1 S2 Q2 Q1

Fibaro Roller

Shutter

Fig. 2 Connecting Roller Shutter to GATE motor

NOTES FOR THE DIAGRAM: L - terminal for live lead N - terminal for neutral lead S1 - terminal for key no. 1 (has the option of entering the device in

learning mode)

S2 - terminal for key No. 2 Q1 - output terminal no. 1 for shutter motor Q2 - output terminal no. 2 for shutter motor B - service button (used to add or remove a device from the

system)

CAUTION

The device is designed for installation in wall switch boxes and can work only with the electrical connectors compliant with the relevant safety

standards.

CAUTION

The switch box must be compliant with the relevant national safety standards and its depth should not

be less than 60mm.

WARNING

Fibaro Roller Shutter is dedicated to operate with AC powered electric motors. Connecting the device directly to DC powered motors may result in them

being damaged.

WARNING

It is recomended to monitor regulary operation of Fibaro Roller shutter in all modes. In case of gate control mode device, motor limit switches, infrared

barriers and emergency stop should be monitored and maintained regulary .

NOTE

A push button connected to S1 terminal operates the Q1 output, while the push button connected to S2 terminal operates the Q2 output. It’s recommended to connect an UP button to S1 terminal and a

wire, responsible of up movement, to Q1 output terminal. Respectively, a DOWN button should be connected to S2 terminal and a wire, responsible for down movement, to Q2 output terminal.

TIPS FOR ARRANGING THE ANTENNA

1. Locate the antenna as far from metal elements as possible

(connection wires, bracket rings, etc.) in order to prevent interferences.

2. Metal surfaces in direct vicinity of the antenna (e.g. metal switch boxes, door frames) may impair radio signal reception!

3. Do not cut or shorten the antenna. Its length is perfectly matched to the band in which the system operates.

VI. Z-WAVE NETWORK INCLUSION

Fibaro Roller Shutter may be included into the Z-Wave network via the B-button or a push button connected to the S1 terminal. In addition, the module may be included in auto inclusion mode, by simply connecting the power supply.

Automatic Z-Wave network inclusion:

1) Make sure the power supply is disconnected and a Roller Shutter is located within a direct Z-Wave network’s main controller communication range.

2) Set the main controller into the learn mode (see main controllers operating manual).

3) Connect the power supply to include the Roller Shutter in auto inclusion mode.

4) Fibaro Roller Shutter will be automatically detected and included into the Z-Wave network.

To disable the auto inclusion mode, press the B-button briefly, after connecting the module to the power supply.

Manual Z-Wave network inclusion:

1) Connect the power supply.

2) Set the main controller into the learn mode (see main controllers

operating manual).

3) Triple click the B-button or a push button connected to the S1 terminal.

4) Fibaro Roller Shutter will be detected and included into the Z-Wave network.

VII. Z-WAVE NETWORK EXCLUSION

1) Make sure the module is connected to the power supply.

2) Set the main controller into the learn mode (see main controllers

operating manual).

3) Triple click the B-button or a push button connected to the S1 terminal.

VIII. ROLLER SHUTTER RESET

Reset procedure clears the modules’ EPROM memory, including all information about the Z-Wave network controller, calibration and power consumption data.

1) Make sure the module is connected to the power supply.

2) Press and hold the B-button for ca. 14 seconds.

3) LED indicator will glow yellow.

4) Release the B-button and press it again, briefly.

5) The Roller Shutter memory is now empty.

6) The module goes into the auto inclusion mode, until any button

is pushed.

CAUTION

Memory reset does not remove the module from the Z-Wave network main controller’s memory. Prior to memory reset it’s recommended to exclude

the module from the Z-Wave network.

TIP

After memory reset, the Roller Shutter goes into the auto inclusion mode and waits to be included into the Z-Wave network. To exit the auto inclusion

mode press the B-button briefly.

IX. POSITIONING CALIBRATION

Calibration is a process during which a Roller Shutter learns the position of the limit switches and a motor characteristic. Calibration is mandatory in order for the Roller Shutter to correctly recognize a roller blind position. The procedure consists of an automatic, full movement between the limit switches (up, down, and up again). There are separate procedures of calibrating roller blind and slats (venetian blind) positioning. Each time the calibration requires the completion of a full cycle (up and down).

ROLLER BLIND POSITIONING CALIBRATION

There are 5 procedures of calibrating a Fibaro Roller Shutter to choose from. Each one gives the same results and the user may choose which one to execute.

A. Calibration through a Fibaro Home Center 2 interface

1) Make sure the module is connected to the power supply,

according to Fig.1

2) Include the module into the Z-Wave network, according to section VI of instructions.

3) In Home Center 2 interface choose Fibaro Roller Shutter’s advanced settings.

4) Click CALIBRATE buttin in the devices advanced settings tab.

5) Roller Shutter performs the calibration process, completing full

cycle - up, down and up again.

6) Using an interface test whether the positioning works correctly.

B. Calibration through the Z-Wave network

1) Make sure the module is connected to the power supply,

according to Fig.1

2) Include the module into the Z-Wave network, according to section VI of instructions.

3) Set the parameter 29 value to 1.

4) Roller Shutter performs the calibration process, completing full

cycle - up, down and up again.

5) The parameter 29 value will be automatically set to 0.

6) Using an interface test whether the positioning works correctly.

C. Calibration through the switch keys

1) Make sure the module is connected to the power supply,

according to Fig.1, and to the switch keys as well (S1 and S2 inputs).

2) Include the module into the Z-Wave network, according to section VI of instructions.

3) Press and hold the switch key connected to S1 or S2 input terminal and release it after at least 3 seconds.

4) Press and hold the same switch key again, and release it after 3 seconds.

5) Now press and hold the same button, for 3 seconds, for the 3rd time.

6) After pressing and releasing the button for the third time, automatic calibration sequence will start.

7) Roller Shutter performs the calibration process, completing full cycle - up, down and up again.

D. Calibration through Menu (B-button)

1) Make sure the module is connected to the power supply,

according to Fig.1

2) Include the module into the Z-Wave network, according to section VI of instructions.

3) Press and hold the B-button for ca. 6 seconds.

4) LED will glow blue.

5) Release the B-button and press it again, briefly.

6) Roller Shutter performs the calibration process, completing full

cycle - up, down and up again.

E. Calibration through a Fibar Command Class control frame. It’s possible to force the calibration process execution through sending a Fibar Command Class control frame through a Z-Wave network main controller.

NOTE

To abort the calibration process press any key (connected to S1 or S2) or send a STOP control frame through the Z-Wave network controller. In

Gate Controller mode the calibration process will be aborted after disconnecting the S2 terminal.

CALIBRATING SLATS POSITIONING IN VENETIAN BLINDS

Apart from calibrating the roller blind position, it’s possible to calibrate the position of venetian blinds slats. After correct calibration, in case of venetian blinds, it’s possible to set the position between the limit switches, as well as the slats angle. By default, time of full turn of the slats is set to 1,5 seconds. If necessary, it can be modified following below instructions.

1) Make sure the module is connected to the power supply, according to Fig.1

2) Include the module into the Z-Wave network, according to section VI of instructions.

3) Calibrate the Roller Shutter, according to the instructions provided in sections IX.A, IX.B, IX.C, IX.D or IX.E.

4) Set the parameter 10 value to 2 or choose in HC2 interface: Device Type - Venetian Blind

5) Another device icon, responsible for slats operation, will show up in Home Center 2 interface. In case of any other Z-Wave network controllers managing the slats position is achieved through pressing and holding a switch key (up or down).

6) By default, time of transition between extreme positions is set to 1 500 ms (1,5 seconds).

7) Turn slats between extreme positions. If after full cycle a blind starts moving up or down, then parameter’s 12 value must be modified, e.g. to 1 000ms (1 second). Correctly configured slats should not force the blind to move up or down.

CAUTION

Roller Shutter needs to be calibrated to work with any given motor.

CAUTION

In Venatian Blind mode, slats need to be calibrated to work with any given motor.

CAUTION

Venetian blind slats may be only operated by momentary switches.

X. OPERATING THROUGH THE Z-WAVE NETWORK

After including into the Z-Wave network, Fibaro Roller Shutter will be presented in a Home Center 2 interface as a roller blind icon (see fig. below). After choosing Venetian Blind device type, a second icon will show up, responsible for managing slats position.

Fig. 4 Roller Shutter icons in Home Center interface

User can choose from the following operating modes:

1. Roller Blind Mode, without positioning

2. Roller Blind Mode, with positioning

3. Venetian Blind Mode

4. Gate Mode, without positioning

5. Gate Mode, with positioning

After choosing one of the above operating modes, device will be represented in Home Center 2 interface by icons shown in Fig.4. In addition, each operating mode affects certain parameters settings:

1) Roller blind without positioning (parameter 10 set to 0)

2) Roller blind with positioning (parameter 10 set to 1)

3) Venetian blind (parameter 10 set to 2; parameter 13, set to 2)

4) Gate without positioning (parameter 10 set to 3; parameter 12 set

to 0; parameter 17 set to 0)

5) Gate with positioning (parameter 10 set to 4; parameter 12 set to 0; parameter 17 set to 0)

NOTE

Above operating modes and their default settings are modified automatically only in Home Center 2 controller. In case of the Z-Wave network controllers from other manufacturers, these

settings need to be manually adjusted (see section XVIII).

Opening / Closing a blind is acheved through moving a slider or pushing a button shown in Fig. 4.

In Venetian Blind mode, setting slats angle is achieved through moving a slider or pushing a button shown in Fig. 4.

XI. MANUAL OPERATION

Fibaro Roller Shutter allows for connecting push buttons to S1 and S2 terminals. These may be momentary or toggle switches, alternatively. Push buttons are responsible for managing the blind’s movement.

Using momentary switches: Clicking button connected to S1 terminal, initiates up movement. Clicking button connected to S2 terminal, initiates down movement.

If the blind is moving, each click, of any button, will stop the movement. In addition a button click sends a command frame to I-st association group devices.

In case of venetian blinds, it’s possible to manage the slats angle. Operating Mode - Venetian Blind, or Parameter 10 value set to 2.

Holding connected to S1 terminal initiates slats rotation up.

Holding connected to S2 terminal initiates slats rotation down.

In addition a button hold sends a Fibar Command Class control frame to II-nd association group devices.

Using toggle switches: Changing switch key position, connected to S1 terminal, initiates up movement. Changing switch key position, connected to S2 terminal, initiates down movement. Choosing a middle position stops the blind.

XII. ASSOCIATIONS

Through an association Fibaro Roller Shutter may control another Z-Wave network device, e.g. another Roller Shutter, Wall Plug, Dimmer, Relay Switch, RGBW Controller.

NOTE

Association allows for direct communication between Z-Wave network devices. Main controller

does not take part in such communication.

Fibaro Roller Shutter provides three association groups:

I association group is triggered through a momentary switch click, or a toggle switch position change.

II association group is triggered through a momentary switch hold

NOTE

II association group is inactive when toggle switches are used or in Gate Controller mode (parameter 10). In case of controlling Venetian Blinds, control

commands are sent in Fibar Command Class standard.

III association group reports the module status. Only one device may be assigned to this group, main controller by default. It’s not recommended to modify this group’s settings. Fibaro Roller Shutter allows for commanding other Roller Shutters, associated into I or II association group, through clicking or holding a switch key. For example, this mechanism allows for operating a Roller Shutter connected to the switch with a button click, and operating the devices associated in II association group by a button hold. In addition, when operating Venetian Blinds, it’s possible to synchronize many devices.

USING ASSOCIATIONS TO OPERATE ANOTHER ROLLER SHUTTER OR ANY OTHER Z-WAVE DEVICE.

I ASSOCIATION GROUP: Clicking button, connected to S1 terminal will initiate up

movement in associated Roller Shutters, or send Turn On command frame to the devices associated in I-st association group.

Clicking button, connected to S2 terminal will initiate down movement in associated Roller Shutters, or send Turn Off command frame to the devices associated in I-st association group.

II ASSOCIATION GROUP: Holding button, connected to S1 terminal will move the

connected roller blind up, and after 1 second delay initiate up movement in associated Roller Shutters, or send Turn On command frame to the devices associated in II-nd association group. Holding button, connected to S2 terminal will move the conected rolled blind down, and after 1 second delay initiate down movement in associated Roller Shutters, or send Turn Off command frame to the devices associated in II-nd association group.

USING ASSOCIATIONS TO OPERATE ROLLER SHUTTERS CONNECTED TO VENETIAN BLINDS.

Using association mechanism to operating venetian blinds requires configuring both, I-st and II-nd association groups.

I ASSOCIATION GROUP Clicking button, connected to S1 terminal will initiate up

movement of the connected venetian blind and other devices

associated in I-st association group. Clicking button, connected to S2 terminal will initiate down movement of the connected venetian blind and other devices associated in I-st association group.

II ASSOCIATION GROUP (relevant for momentary switches only) Holding button, connected to S1 terminal will initiate slats

rotation up, of the connected venetian blind as well as the other devices associated in II-nd association group. Holding button, connected to S2 terminal will initiate slats rotation down, of the connected venetian blind as well as the other devices associated in II-nd association group.

NOTE

Once the associated devices are already moving, they will be stopped if any of the buttons is pressed

and held.

XIII. OPERATING GATE MOTORS

Fibaro Roller Shutter allows for operating gate motors. Gate motor should be connected to Q1 and Q2 terminals according to Fig.2. In the Gate Mode, a momentary switch may be connected to S1 terminal. It’s recommended to connect an IR barrier, an emergency stop button or any alarm mechanism to S2 terminal. Opening a contact in a device connected to S2 terminal will always result in stopping a motor in current position (see Fig. 2).

Clicking a push button connected to S1 terminal will initiate opening the gate. Next click of a button will stop the gate. Yet another click of a button will close the gate. According to following seaquence:

OPEN → STOP → CLOSE → STOP → OPEN.

Fig. 5 Roller Shutter icon in Home Center interface

NOTE

In Gate Mode, by default, the S1 terminal is set to operate with a momentary switch, ignoring the

parameter 14 settings.

Full opening the gate initiates a Roller Shutter COUNTDOWN. After the COUNTDOWN the gate will start closing. COUNTDOWN length is set through the parameter 12. In addition, if the IR barrier is cut (S2 contact opened) at the gate fully open, the gate will start closing after a time period specified in parameter 17.

NOTE

In both Gate Modes, with and without positioning, parameters 12 and 17 are automatically set to 0. At these settings the gate will open, but will not automatically close. Relevant times need to be set

manually in parameters 12 and 17 (see section XVIII).

NOTE

Parameters 12 and 17 settings are automatically modified only in Home Center 2 controller, when choosing one of Gate Modes. In case of controllers

from other manufacturers these parameters need to be set manually (see section XVIII).

NOTE

Installation of the gate driver may be performed only by certified professionals. The motor must be equipped with the appropriate limit switches (see Fig

2). It’s recommended to connect a NC (normally closed) contact of an IR barrier to S2 terminal. Opening the contact will stop the gate. In addition, it’s recommened to connect an emergency stop

button to the motors neutral (N) wire. In emergency, pushing the emergency stop button will cut the power and stop the gate. It is recomended to monitor regulary operation of Fibaro Roller shutter in all modes. Also it is recomended to regulary verificate and maintenance connectors.

NOTE

S1 and S2 terminals react to mains voltage only. Using IR barriers with NC contacts operating on lower voltages require using an additional relay (see

Fig. 2)

XIV. LED INDICATOR

Fibaro Roller Shutter has a MENU. Each MENU level is signaled through a LED Indicator colour. To enter MENU press and hold the B-button for at least 2 seconds.

While the B-button is being held, LED Indicator colours will change in the following sequence:

BLUE - Roller Shutter calibration procedure (see section IX) VIOLET - initiate the Z-Wave network range tester GREEN - reset energy consumption data memory (see section XVI) YELLOW - Roller Shutter reset (see section VIII)

Release the B-button to choose the desired function and confirm your choice with the B-button click.

XV. Z-WAVE RANGE TESTER

Fibaro Roller Shutter has a built in mechanism, allowing to roughly estimate the Z-Wave network range.

CAUTION

To allow for the Z-Wave network range test, the Z-Wave network controller needs to support the functionality and the module needs to be included in the network. Z-Wave range test puts heavy strain

on the network, so it’s recommended to use the function only in special cases.

In order to test the Z-Wave network range:

1) Press and hold the B-button for ca. 6 seconds, until the LED Indicator glows violet.

2) Release the B-button.

3) Click the B-button.

4) LED Indicator will signal the Z-Wave network range (see

description below).

5) Click the B-button to exit the Range Tester.

Network range signaling modes: Z-Wave network range is signaled by LED illumination colour and behaviour. Blinking each 1-second means the modules tries to establish a direct communication with the main controller, while 2 seconds glowing means the test result. The test is performed in a loop, until being stopped by the user. Z-Wave range test is performed in three steps, signaled with green, yellow, violet and red:

1) Blinking in GREEN means the module tries to establish a direct communication with the main controller. Positive test result is signaled by a 2 second glowing in GREEN, after which the test is repeated (step 1). In practice, if the module is able to establish a direct communication with the main controller, the LED will glow GREEN, without blinking.

2) If the module is not able to establish a direct connection with the main controller, it will try to establish a routed connection, through another, intermediary, Z-Wave network devices. LED indicator will change the illumination colour to RED. Positive test result is signaled with glowing in YELLOW. After 2 seconds the module will retry establishing a direct communication (step 1).

NOTE

The module may modify the main controller communication from direct to routed and vice versa, especially if it’s located at the direct

communication range limit.

3) If the module is not able to establish a routed connection with the main controller, LED Indicator colour will change from YELLOW to VIOLET. After few seconds test will end and the LED Indicator will glow RED for two seconds. Whole procedure will start again and the module will try to establish a direct connection with the main controller (step 1).

XVI. CURRENT AND HISTORICAL POWER CONSUMPTION MEASURING

Fibaro Roller Shutter allows for the current load and power consumption monitoring. Data is sent to the main controller, e.g. Home Center 2. Measuring is carried out by an independent microprocessor dedicated exclusively for the purpose, assuring maximum accuracy and precision. The microprocessor is factory calibrated.

Electric power - power consumed by an electric device in an instant, in Watts (W).

Electric energy - energy consumed by a device through a time period. Most commonly measured in kilowatt-hours (kWh). One kilowatt-hour is equal to one kilowatt of power consumed over a period of one hour, 1kWh = 1000 Wh.

RESETTING ELECTRICITY CONSUMPTION MEMORY

Fibaro Roller Shutters electricity consumption memory may be cleared in one of the following ways:

1) Through the module reset (see section VIII)

2) Through the main controller menu (see main controllers

operating manual

3) Manually using the following instructions:

a) Make sure the device is connected to voltage supply. b) Press and hold the B-button for ca. 10 seconds, until LED I

ndicator glows GREEN.

c) Release the B-button. d) Click the B-button. e) Energy consumption memory has been erased.

NOTE

1) Please contact your local supplier for the current

rates

2) Fibaro Roller Shutter stores consumed electricity data on its memory, which means disconnecting the

module from voltage supply does not erase the data.

XVII. PROTECTION MODE

Fibaro Roller Shutter uses the Protection Command Class v2 to prevent from unintended motor movement.

1) Local Protection Local Protection State: 0 - no protection. Roller Shutter responds to push buttons. 1 - not supported 2 - Local protection active. Roller Shutter does not respond to push buttons.

Once the Local Protection is activated, the module stops responding to S1 and S2 push buttons. SCENE ID and association commands will not be sent as well. The only exception is the B-button. Menu and Z-Wave network inclusion, after the B-button or S1 push button triple click, are still active.

WARNING

In Protection Mode it will not be possible to control Fibaro Roller Shutter from buttons. It is not recomended to control all Fibaro Roller Shutters in this mode.

CAUTION

There’s one more exception in Local Protection. In Gate Mode, S2 (IR Barrier) is still active. It means if the obstacle is detected, the gate will stop,

regardless the Local Protection State set.

2) RF Protection (radio protection) RF Protection State: 0 – No protection. Roller Shutter responds to command frames. 1 - RF Protection active. Roller Shutter does not respond to the Z-Wave control frames. 2 - not supported.

Once the RF Protection is activated, the module stops responding to command frames setting the blind position. It’s still possible however to configure the device (advanced configuration parameters, protection modes) and checking it’s current state through polling (position, power, energy).

XVIII. ADVANCED CONFIGURATION

GENERAL SETTINGS:

3. Reports type

0 – Blind position reports sent to the main controller using Z-Wave

Command Class. 1 - Blind position reports sent to the main controller using Fibar Command Class. Parameters value shoud be set to 1 if the module operates in Venetian Blind mode.

Default setting: 0 Parameter size: 1 [byte]

NOTE

To make sure whether Fibar Command Class is supported by Z-Wave network main controllers from other manufacturers, please contact the

controllers manufacturer.

10. Roller Shutter operating modes:

0 - Roller Blind Mode, without positioning 1 - Roller Blind Mode, with positioning 2 - Venetian Blind Mode, with positioning 3 - Gate Mode, without positioning 4 - Gate Mode, with positioning

Default settng: 1 Parameter size: 1 [byte]

12. In Venetian Blind mode (parameter 10 set to 2) the parameter determines time of full turn of the slats.

In Gate Mode (parameter 10 set to 3 or 4) the parameter defines the COUNTDOWN time, i.e. the time period after which an open gate starts closing. In any other operating mode the parameter value is irrelevant. Value of 0 means the gate will not close automatically.

Available settings: 0-65535 (0 - 655,35s) Default setting: 150 (1,5 s) Parameter size: 2 [bytes]

13. Set slats back to previous position.

In Venetian Blind Mode (parameter 10 set to 2) the parameter influences slats positioning in various situations. In any other operating mode the parameter value is irrelevant.

0 - Slats return to previously set position only in case of the main controller operation. 1 - Slats return to previously set position in case of the main controller operation, momentary switch operation, or when the limit switch is reached. 2 - Slats return to previously set position in case of the main controller operation, momentary switch operation, when the limit switch is reached or after receiving a “STOP” control frame (Switch Multilevel Stop).

Default setting: 1 Parameter size: 1 [byte]

14. Switch type.

The parameter settings are relevant for Roller Blind Mode and Venetian Blind Mode (parameter 10 set to 0, 1, 2).

0 - Momentary switches 1 - Toggle switches 2 - Single, momentary switch. (The switch should be connected to

S1 terminal)

Default setting: 0 Parameter size: 1 [byte]

17. In Roller Blind Mode or Venetian Blind mode (parameter 10 set to 0, 1, 2) the parameter determines when the Roller Shutter relays are turned off after reaching a limit switch.

In Gate Mode (parameter 10 set to 3 or 4) the parameter determines a time period after which a gate will start closing after a S2 contact has been disconnected. In this mode, time to turn off the Roller Shutter relays after reaching a limit switch is set to 3 seconds and cannot be modified. Value of 0 means the gate will note close automatically.

Available settings: 0 - 255 (0,1-25,5s). Default setting: 10 (1s). Parameter size: 1 [byte]

18. Motor operation detection.

Power threshold to be interpreted as reaching a limit switch.

Available settings: 0 - 255 (1-255 W) The value of 0 means reaching a limit switch will not be detected Default setting: 10 (10W). Parameter size: 1 [byte]

22. Motor operation time.

Time period for the motor to continue operation.

Available settings: 0 – 65535 (0 – 65535s) The value of 0 means the function is disabled. Default setting: 240 (240s. – 4 minutes) Parameter size: 2 [bytes]

29. Forced Roller Shutter calibration.

By modifying the parameters setting from 0 to 1 a Roller Shutter enters the calibration mode. The parameter relevant only if a Roller Shutter is set to work in positioning mode (parameter 10 set to 1, 2 or 4).

1 - Start calibration process Default setting: 0 Parameter size: 1 [byte]

ALARM SETTINGS:

30. Response to general alarm 0 - No reaction. 1 - Open blind. 2 - Close blind.

Default setting: 2 Parameter size: 1 [byte]

31. Response to flooding alarm

0 - No reaction. 1 - Open blind. 2 - Close blind.

Default setting: 0 Parameter size: 1 [byte]

32. Response to smoke, CO or CO2 alarm

0 - No reaction. 1 - Open blind. 2 - Close blind.

Default setting: 1 Parameter size: 1 [byte]

33. Response to temperature alarm

0 - No reaction. 1 - Open blind. 2 - Close blind.

Default setting: 1 Parameter size: 1 [byte]

35. Managing slats in response to alarm.

In Venetian Blind Mode (parameter 10 set to 2), the parameter determines how the slats will react upon alarm detection. In any other modes, the parameter value is not relevant.

0 - Do not change slats position - slats return to the last set position. 1 - Set slats to their extreme position.

Default setting: 1 Parameter size: 1 [byte]

POWER AND ENERGY REPORTS SETTINGS:

40. Power reports.

Power level change that will result in new power value report being sent. The parameter defines a change that needs to occur in order to trigger the report. The value is a percentage of the previous report.

Power report threshold available settings: 1-100 (1-100%). Value of 0 means the reports are turned off.

Default setting: 10 (10%). Parameter size: 1 [byte]

42. Periodic power or energy reports.

The parameter defines a time period between consecutive reports.

Available settings: 1-65534 (1-65534 seconds) Value of 0 means the reports are turned off.

Default setting: 3600 (3600 seconds / 60 minutes). Parameter size: 2 [bytes]

43. Energy reports.

Energy level change which will result in new energy value report being sent. The parameter defines a change that needs to occur in order to trigger the report.

Energy threshold available settings: 1-254 (0,01 - 2,54kWh). Value of 0 means the reports are turned off.

Default setting 10 (0,1kWh). Parameter size: 1 [byte]

44. Self-measurement.

A Roller Shutter may include power and energy used by itself in reports sent to the main controller.

0 - Self-measurement inactive. 1 - Self-measurement active.

Default setting: 0 Parameter size: 1 [byte]

SCENES AND ASSOCIATIONS SETTINGS:

50. Scenes / Associations activation.

Parameter determines whether scenes or associations are activated by the switch keys.

0 - Associations activation 1 - Scenes activation

Default setting: 0 Parameter size: 1 [byte]

XIX. GUARANTEE

1. FIBAR GROUP S.A. with its registered office in Poznan, ul.

Lotnicza 1, 60-421 Poznań, entered into the Register of

Entrepreneurs of the National Court Register maintained by the

District Court for Poznań-Nowe Miasto and Wilda in Poznań, VIII

Commercial Division of the National Court Register (KRS) under number: 553265, NIP 7811858097, REGON: 301595664, share capital PLN 1,182,100 paid in full, other contact information is available at: www.fibaro.com (hereinafter "the Manufacturer") guarantees that the device sold (hereinaftr: "the Device" is free from material and manufacturing defects.

2. The Manufacturer shall be responsible for malfunctioning of the Device resulting from physical defects inherent in the Device that cause its operation to be incompatible with the specifications within the period of:

- 24 months from the date of purchase by the consumer,

- 12 months from the date of purchase by a business customer (the consumer and business customer are further collectively referred to as "Customer").

3. The Manufacturer shall remove any defects revealed during the guarantee period, free of charge, by repairing or replacing (at the sole discretion of the Manufacturer) the defective components of the Device with new or regenerated components. The manufacturer reserves the right to replace the entire Device with a new or regenerated device. The Manufacturer shall not refund money paid for the device.

4. Under special circumstances, the Manufacturer may replace the Device with a different device most similar in technical characteristics.

5. Only the holder of a valid guaranty document shall be entitled to make claims under guarantee.

6. Before making a complaint, the Manufacturer recommends using the telephone or online support available at https://www.fibaro.com/support/.

7. In order to make a complaint, the Customer should contact the Manufacturer via the email address given at https://www.fibaro.com/support/.

8. After the complaint has been properly filed, the Customer will receive contact details for the Authorized Guarantee Service ("AGS"). The customer should contact and deliver the Device to AGS. Upon receipt of the Device, the manufacturer shall inform the Customer of the return merchandise authorization number (RMA).

9. Defects shall be removed within 30 days from the date of delivering the Device to AGS. The guarantee period shall be extended by the time in which the Device was kept by AGS.

10. The faulty device shall be provided by the Customer with complete standard equipment and documents proving its purchase.

11. The cost of transporting the Device in the territory of the Republic of Poland shall be covered by the Manufacturer. The costs of the Device transport from other countries shall be covered by the Customer. For unjustified complaints, AGS may charge the

Customer with costs related to the case.

12. AGS shall not accept a complaint claim when:

- the Device was misused or the manual was not observed,

- the Device was provided by the Customer incomplete, without accessories or nameplate,

- it was determined that the fault was caused by other reasons than a material or manufacturing defect of the Device

- the guarantee document is not valid or there is no proof of purchase,

13. The guarantee shall not cover:

- mechanical damages (cracks, fractures, cuts, abrasions, physical deformations caused by impact, falling or dropping the device or other object, improper use or not observing the operating manual);

- damages resulting from external causes, e.g.: flood, storm, fire, lightning, natural disasters, earthquakes, war, civil disturbance, force majeure, unforeseen accidents, theft, water damage, liquid leakage, battery spill, weather conditions, sunlight, sand, moisture, high or low temperature, air pollution;

- damages caused by malfunctioning software, attack of a computer virus, or by failure to update the software as recommended by the Manufacturer;

- damages resulting from: surges in the power and/or telecommunication network, improper connection to the grid in a manner inconsistent with the operating manual, or from connecting other devices not recommended by the Manufacturer.

- damages caused by operating or storing the device in extremely adverse conditions, i.e. high humidity, dust, too low (freezing) or too high ambient temperature. Detailed permissible conditions for operating the Device are defined in the operating manual;

- damages caused by using accessories not recommended by the Manufacturer

- damages caused by faulty electrical installation of the Customer, including the use of incorrect fuses;

- damages caused by Customer's failure to provide maintenance and servicing activities defined in the operating manual;

- damages resulting from the use of spurious spare parts or accessories improper for given model, repairing and introducing alterations by unauthorized persons;

- defects caused by operating faulty Device or accessories.

14. The guarantee shall not cover natural wear and tear of the Device and its components listed in the operating manual and in technical documentation as such elements have a defined operational life.

15. The Device Guarantee shall not exclude, limit or suspend the Customer's warranty rights.

16. The Manufacturer shall not be liable for damages to property caused by defective device. The Guarantor shall not be liable for indirect, incidental, special, consequential or punitive damages, or for any damages, including, inter alia, loss of profits, savings, data, loss of benefits, claims by third parties and any other damages arising from or related to the use of the Device.

Simplified EU declaration of conformity:

Hereby, Fibar Group S.A. declares that the device is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.manuals.fibaro.com

WEEE Directive Compliance:

Device labelled with this symbol should not be disposed with other household wastes. It shall be handed over to the applicable collection point for the recycling of waste electrical and electronic equipment.

Attention!

This product is not a toy. Keep away from children and animals!

This device complies with Part 15 of the FCC Rules

Operation is subject to the following two conditions:

1. This device may not cause harmful interference

2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Notice

This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux normes d’exemption de licence RSS d’Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer d’interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement.

Note

Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission’s rules.

This Device may be used with all devices certified with Z-Wave certificate and should be compatible with such devices produced by other manufacturers.

Any device compatible with Z-Wave may be added to Fibaro system.